Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ThIn”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Turbulent viscous drag reduction with thin-element riblets

Thin-element riblets for aircraft aerodynamic surface turbulent viscous drag reduction are presently found to be as effective as symmetric V-grooves in this role, while possessing a greater range of admissible spacings. The thin-element geometry shows the qualitatively predictable influence of independent riblet height and spacing variations. The evidence for more than one drag-reduction mechanism in thin-element riblets is found to be inconclusive.

Lazos, B.↗
NASA NTRS1988

Analytic limits on the forms of spectra possible from optically thin collisional bremsstrahlung source models

The constraints on hard X-ray bremsstrahlung spectral forms required in order for them to correspond to physically acceptable (nonnegative) electron distributions in thin-target, thick-target, and thermal source models are discussed. The extent to which various spectra can be attributed to the different models is examined, showing that many possible spectra cannot be described by all, or in some cases, any of the models. It is shown that for any bremsstrahlung cross section, the thick-target and thermal models require that successively higher derivatives of the thin-target constraint have the appropriate sign. It is found that thermal models are the most restrictive, and that thin-target models are the least restrictive. Explicit analytic constraint expressions are derived for all three cases for the Kramers cross section and examples of acceptable and unacceptable spectra are given. Application of these criteria to the testing and exclusion of models is discussed.

Brown, John C.↗
NASA NTRS1988

Commercial aspects of epitaxial thin film growth in outer space

A new concept for materials processing in space exploits the ultra vacuum component of space for thin film epitaxial growth. The unique low earth orbit space environment is expected to yield 10 to the -14th torr or better pressures, semiinfinite pumping speeds and large ultra vacuum volume (about 100 cu m) without walls. These space ultra vacuum properties promise major improvement in the quality, unique nature, and the throughput of epitaxially grown materials especially in the area of semiconductors for microelectronics use. For such thin film materials there is expected a very large value added from space ultra vacuum processing, and as a result the application of the epitaxial thin film growth technology to space could lead to major commercial efforts in space.

Ignatiev, Alex↗
NASA NTRS1988

Technique for measuring the dielectric constant of thin materials

A practical technique for measuring the dielectric constant of vegetation leaves and similarly thin materials is presented. A rectangular section of the leaf is placed in the tranverse plane in a rectangular waveguide and the magnitude and phase of the reflection coefficient are measured over the desired frequency band using a vector network analyzer. By treating the leaf as an infinitesimally thin resistive sheet, an explicit expression for its dielectric constant is obtained in terms of the reflection coefficient. Because of the thin-sheet approximation, however, this approach is valid only at frequencies below 1.5 GHz. To extend the technique to higher frequencies, higher order approximations are derived and their accuracies are compared to the exact dielectric-slab solution. For a material whose thickness is 0.5 mm or less, the proposed technique was found to provide accurate values of its dielectric constant up to frequencies of 12 GHz or higher. The technique was used to measure the 8 to 12 GHz dielectric spectrum for vegetation leaves, teflon and rock samples.

Sarabandi, K.↗
NASA NTRS1988

A proposal for epitaxial thin film growth in outer space

A new concept for materials processing in space exploits the ultravacuum component of space for thin film epitaxial growth. The unique low earth orbit space environment is expected to yield 10 to the -14th torr or better pressures, semiinfinite pumping speeds, and large ultravacuum volume without walls. These space ultravacuum properties promise major improvement in the quality, unique nature, and the throughput of epitaxially grown materials. Advanced thin film materials to be epitaxially grown in space include semiconductors, magnetic materials, and thin film high temperature superconductors.

Ignatiev, Alex↗
NASA NTRS1990

Matrix.Vector Multiplication In Thin Photorefractive Crystal

Thin GaAs device integrated with other electronic and optoelectronic devices. Experiments show matrix.vector multiplication performed optically by four-wave mixing in thin crystal of GaAs. Concept applicable to thin crystals of other photorefractive materials having suitable electro-optical properties and same crystalline symmetry as that of GaAs.

Cheng, Li-Jen↗
NASA NTRS1989

Static and free-vibrational response of semi-circular graphite-epoxy frames with thin-walled open sections

Experiments were conducted to measure the three-dimensional static and free vibrational response of two graphite-epoxy, thin-walled, open section frames. The frames are semi-circular with a radius of three feet, and one specimen has an I cross section and the other has a channel cross section. The flexibility influence coefficients were measured in static tests for loads applied at midspan with the ends of the specimens clamped. Natural frequencies and modes were determined from vibrational tests for free and clamped end conditions. The experimental data is used to evaluate a new finite element which was developed specifically for the analysis of curved, thin-walled structures. The formulation of the element is based on a Vlasov-type, thin-walled, curved beam theory. The predictions from the finite element program generally correlated well with the experimental data for the symmetric I-specimen. Discrepancies in some of the data were found to be due to flexibility in the clamped end conditions. With respect to the data for the channel specimen, the correlation was less satisfactory. The finite element analysis predicted the out-of-plane response of the channel specimen reasonably well, but large discrepancies occurred between the predicted in-plane response and the experimental data. The analysis predicted a much more compliant in-plane response than was observed in the experiments.

Collins, J. Scott↗
NASA NTRS1990

Attachment of lead wires to thin film thermocouples mounted on high temperature materials using the parallel gap welding process

Parallel gap resistance welding was used to attach lead wires to sputtered thin film sensors. Ranges of optimum welding parameters to produce an acceptable weld were determined. The thin film sensors were Pt13Rh/Pt thermocouples; they were mounted on substrates of MCrAlY-coated superalloys, aluminum oxide, silicon carbide and silicon nitride. The entire sensor system is designed to be used on aircraft engine parts. These sensor systems, including the thin-film-to-lead-wire connectors, were tested to 1000 C.

Holanda, Raymond↗
NASA NTRS1990

Sequentially evaporated thin film YBa2Cu3O(7-x) superconducting microwave ring resonator

There is great interest in the application of thin film high temperature superconductors in high frequency electronic circuits. A ring resonator provides a good test vehicle for assessing the microwave losses in the superconductor and for comparing films made by different techniques. Ring resonators made of YBa2Cu3O(7-x) have been investigated on LaAlO3 substrates. The superconducting thin films were deposited by sequential electron beam evaporation of Cu, Y, and BaF2 with a post anneal. Patterning of the superconducting film was done using negative photolithography. A ring resonator was also fabricated from a thin gold film as a control. Both resonators had a gold ground plane on the backside of the substrate. The ring resonators' reflection coefficients were measured as a function of frequency from 33 to 37 GHz at temperatures ranging from 20 K to 68 K. The resonator exhibited two resonances which were at 34.5 and 35.7 GHz at 68 K. The resonant frequencies increased with decreasing temperature. The magnitude of the reflection coefficients was in the calculation of the unloaded Q-values. The performance of the evaporated and gold resonator are compared with the performance of a laser ablated YBa2Cu3O(7-x) resonator. The causes of the double resonance are discussed.

Rohrer, Norman J.↗
NASA NTRS1990

Free vibrations of thin-walled semicircular graphite-epoxy composite frames

A detailed study is made of the effects of variations in lamination and material parameters of thin walled composite frames on their vibrational characteristics. The structures considered are semicircular thin walled frames with I and J sections. The flanges and webs of the frames are modeled by using 2-D shell and plate finite elements. A mixed formulation is used with the fundamental unknowns consisting of both the generalized displacements and stress resultants in the frame. The frequencies and modes predicted by the 2-D finite element model are compared with those obtained from experiments, as well as with the predictions of a non-dimensional thin walled beam finite element model. A detailed study is made of the sensitivity of the vibrational response to variations in the fiber orientation, material properties of the individual layers, and boundary conditions.

Carden, Huey D.↗
NASA NTRS1990

The effect of temperature cycling typical of low earth orbit satellites on thin films of YBa2Cu3O(7-x)

The refrigeration of superconductors in space poses a challenging problem. The problem could be less severe if superconducting materials would not have to be cooled when not in use. Thin films of the YBa2Cu3O(7-x) (YBCO) superconductor were subjected to thermal cycling, which was carried out to simulate a large number of eclipses of a low earth orbit satellite. Electrical measurements were performed to find the effect of the temperature cycling. Thin films of YBCO were formed by coevaporation of Y, BaF2, and Cu and postannealing in wet oxygen at 850 C for 3.5 h. The substrates used were (100) SrTiO3, polycrystalline alumina, and oxidized silicon; the last two have an evaporated zirconia layer. Processing and microstructure studies of these types of films have been published. THe zero resistance transition temperatures of the samples used in this study were 91, 82, and 86 K, respectively. The samples were characterized by four point probe electrical measurements as a function of temperature. The parameters measured were: the zero resistance transition temperature, the 10 to 90 percent transition width, and the room temperature resistance, normalized to that measured before temperature cycling. The results for two samples are presented. Each sample had a cumulative exposure. Cycling in atmospheric pressure nitrogen was performed at a rate of about 60 cycles per day, whereas in vacuum the rate was only about 10 cycles per day. The results indicate only little or no changes in the parameters measured. Degradation of superconducting thin films of YBCO has been reported due to storage in nitrogen. It is believed that the relatively good performance of films after temperature cycling is related to the fact that BaF2 was used as an evaporation source. The latest result on extended temperature cycling indicates significant degradation. Further tests of extended cycling will be carried out to provide additional data and to clarify this preliminary finding.

Mogro-Campero, A.↗
NASA NTRS1990

Preparation and characteristics of superconducting cuprate thin films: Nd(2-x)Ce(x)CuO4 and substituted Bi-system

Characteristics of the electron-doped-type Nd(2-x)Ce(x)CuO4 systems and substituted Bi2(Sr,Ln)3Cu2Oy system were systematically studied using the high quality thin-film samples. The Nd(2-x)Ce(x)CuO4 thin films with various Ce concentrations, x, were prepared by RF magnetron sputtering on SrTiO3 heated at around 500 C. After subsequent annealing at 1100 C in air, the films showed the c-axis orientation normal to the substrates. By means of the reducing treatment (annealing in a vacuum), superconductivity was induced for the films with 0.14 is less than or equal to x is less than or equal to 0.18. The superconductivity and transport properties of the films were strongly affected by the reducing treatment. The x = 0.15 film exhibited a sharp superconducting transition with zero resistivity at 22 K, in consistent with the diamagnetic properties. The resistivity of the films was fairly low with metallic characteristics, and the sight of the Hall coefficient was negative in the normal state. On the other hand, the normal-state optical measurements showed that the undoped Nd2CuO4 is a semiconductor with a charge transfer gap of 1.3 eV, and that, when Ce ions were doped, a plasma reflection due to the free-carriers came to be seen with the plasma frequency of 1.07 eV for 0.14 is less than or equal to x is less than or equal to 0.18. Moreover, x ray photoemission study revealed that the Cu valence of the film decreased for 2(+) for x = 0 to 1(+) for x = 0.15. These physical properties are in contrast with those of hole-doped-type cuprate superconductors. Bi2(Sr,Ln)3Cu2Oy thin films were also prepared on MgO substrates heated at 600 to 700 C by similar methods. It was found that the growth conditions for Bi-systems with two CuO2 planes were different for each composition and species of lanthanoid in the films. Moreover, preparation of Bi-system with three CuO2 planes was very difficult when lanthanoid atoms were doped in the system. Their electric transport properties and x ray photoemission spectroscopy were investigated. Carrier concentration and Cu valence were discussed with regard to the superconductivity.

Adachi, H.↗
NASA NTRS1990

Optical and microwave detection using Bi-Sr-Ca-Cu-O thin films

Recent progress at the Johns Hopkins University Applied Physics Laboratory (JHU/APL) in the development of optical and microwave detectors using high temperature superconducting thin films is described. Several objectives of this work have been accomplished, including: deposition of Bi-Sr-Ca-Cu-O thin films by laser abation processing (LAP); development of thin film patterning techniques, including in situ masking, wet chemical etching and laser patterning; measurements of bolometric and non-bolometric signatures in patterned Bi-Sr-Ca-Cu-O films using optical and microwave sources, respectively; analysis and design of an optimized bolometer through computer simulation, and investigation of its use in a Fourier transform spectrometer. The focus here is primarily on results from the measurement of the bolometric and non-bolometric response.

Grabow, B. E.↗
NASA NTRS1990

Some optical and electron microscope comparative studies of excimer laser-assisted and nonassisted molecular-beam epitaxically grown thin GaAs films on Si

The quality of GaAs thin films grown via MBE under pulsed excimer laser irradiation on Si substrates is examined in both laser-irradiated and nonirradiated areas using Raman scattering, Rayleigh scattering, and by photoluminescence (PL), as a function of temperature, and by TEM. The temperature dependence of the PL and Raman peak positions indicates the presence of compressive stress in the thin GaAs films in both laser-irradiated and nonirradiated areas. This indicates incomplete homogeneous strain relaxation by dislocations at the growth temperature. The residual compressive strain at the growth temperature is large enough such that even with the introduction of tensile strain arising from the difference in thermal expansion coefficients of GaAs and Si, a compressive strain is still present at room temperature for these thin GaAs/Si films.

Lao, Pudong↗
NASA NTRS1990

Microwave characterization of high-temperature superconducting thin films using stripline resonators

A method was derived for the extraction of the surface resistivity (Rs) of high-Tc superconducting (HTS) thin films at microwave frequencies, using a stripline resonator circuit. Surface resistivity values were calculated by measuring the difference in Q-values of a stripline resonator configuration when an HTS thin film was substituted for one of the metallic ground planes. Cryogenic tests were completed for several stripline resonator structures, yielding accurate predictions of the HTS thin-film performance at frequencies between 3 and 26 GHz (in harmonics of approximately 3 GHz). These results were then used to illustrate the dependence of HTS surface resistivity on frequency and temperature in the microwave frequency band.

Macdonald, Alan D.↗
NASA NTRS1990

Determination of surface resistance and magnetic penetration depth of superconducting YBa2Cu3O(7-delta) thin films by microwave power transmission measurements

A novel waveguide power transmission measurement technique was developed to extract the complex conductivity of superconducting thin films at microwave frequencies. The microwave conductivity was taken of two laser ablated YBa2Cu3O(7-delta) thin films on LaAlO3 with transition temperatures of approx. 86.3 and 82 K, respectively, in the temperature range 25 to 300 K. From the conductivity values, the penetration depth was found to be approx. 0.54 and 0.43 micron, and the surface resistance (R sub s) to be approx. 24 and 36 micro-Ohms at 36 GHz and 76 K for the two films under consideration. The R sub s values were compared with those obtained from the change in the Q-factor of a 36 GHz Te sub 011-mode (OFHC) copper cavity by replacing one of its end walls with the superconducting sample. This technique allows noninvasive characterization of high transition temperature superconducting thin films at microwave frequencies.

Bhasin, K. B.↗
NASA NTRS1990

Free vibrations of thin-walled semicircular graphite-epoxy composite frames

A detailed study is made of the effects of variations in lamination and material parameters of thin walled composite frames on their vibrational characteristics. The structures considered are semicircular thin walled frames with I and J sections. The flanges and webs of the frames are modelled by using 2-D shell and plate finite elements. A mixed formulation is used with the fundamental unknowns consisting of both the generalized displacements and stress resultants in the frames. The frequencies and modes predicted by the 2-D finite element model are compared with those obtained from experiments, as well as with the predictions of a 1-D thin walled beam finite element model. A detailed study is made of the sensitivity of the vibrational response to variations in the fiber orientation, material properties of the individual layers, and boundary conditions.

Noor, Ahmed K.↗
NASA NTRS1990

A flammability study of thin plastic film materials

The Materials Science Laboratory at the Kennedy Space Center presently conducts flammability tests on thin plastic film materials by using a small needle rake method. Flammability data from twenty-two thin plastic film materials were obtained and cross-checked by using three different testing methods: (1) the presently used small needle rake; (2) the newly developed large needle rake; and (3) the previously used frame. In order to better discern the melting-burning phenomenon of thin plastic film material, five additional specific experiments were performed. These experiments determined the following: (1) the heat sink effect of each testing method; (2) the effect of the burn angle on the burn length or melting/shrinkage length; (3) the temperature profile above the ignition source; (4) the melting point and the fire point of each material; and (5) the melting/burning profile of each material via infrared (IR) imaging. The results of these experimentations are presented.

Skinner, S. Ballou↗