Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TWINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Highly mobile type II twin boundary in Ni-Mn-Ga five-layered martensite

Twin relationships and stress-induced reorientation were studied in Ni{sub 2}Mn{sub 1.14}Ga{sub 0.86} single crystal with five-layered modulated martensite crystal structure. Very low twinning stress of about 0.1 MPa was found for twin boundaries which deviated a few degrees from the (011) crystallographic plane. However, twin boundaries oriented exactly parallel to the (011) plane exhibited considerably higher level of twinning stress, above 1 MPa. X-ray diffraction experiments and calculations based on approximation of the martensite crystal lattice as a tetragonal lattice with a slight monoclinic distortion identified the two different kinds of twin interfaces as type II and type I twin boundaries.

36 MATERIALS SCIENCE↗

Digital Twin Enabling Technologies for Online Condition Monitoring of Nuclear Power Plant Components

Online condition monitoring is an area of active research that may enable improved scheduling, maintenance, and safety of nuclear power plant components, reducing unnecessary derate while simultaneously improving operational capacity. Digital twins are one avenue to conduct online condition monitoring and are currently being explored by national laboratories and universities alike. Digital twins for online condition monitoring are, in essence, state concurrent models that emulate a physical process which predicts a parameter and compares it against a measured value. However, digital twins may also provide additional insights by combining and interpreting various sources of information. These insights may be used for preventative maintenance scheduling optimization or early fault detection and are projected to be valuable for meeting requirements under 10 CFR 50.55a. However, digital twin technologies are still under significant development; quantifying model uncertainties, improving unique fault identification, and multimodal sensor fusion are some areas under investigation. Therefore, in this work, we discuss and review the various enabling technologies, in the form of advanced sensors, instrumentation, and modelling methods, that may be used to implement and enhance digital twins for online condition monitoring. A potential use case for pump-motors is presented to demonstrate how these various pieces of enabling digital twin technologies may integrated together for online condition monitoring. Challenges and opportunities associated with the pump-motor digital twin enabling technologies are also identified and discussed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Digital-Twin-Enabling Technologies for Online Condition Monitoring of Nuclear Power Plant Components

Online condition monitoring is an area of active research that may enable improved scheduling, maintenance, and safety of nuclear power plant components, reducing unnecessary derates while simultaneously improving operational capacity. Digital twins are one avenue to conduct online condition monitoring and are currently being explored by national laboratories and universities alike. Digital twins for online condition monitoring are, in essence, state concurrent models that emulate a physical process which predicts a parameter and compares it against a measured value. However, digital twins may also provide additional insights by combining and interpreting various sources of information. These insights may be used for preventative maintenance scheduling optimization or early fault detection and are projected to be valuable for meeting requirements under 10 CFR 50.55a. However, digital twin technologies are still under significant development; quantifying model uncertainties, improving unique fault identification, and multimodal sensor fusion are some areas under investigation. Therefore, in this work, we discuss and review the various enabling technologies, in the form of advanced sensors, instrumentation, and modelling methods, that may be used to implement and enhance digital twins for online condition monitoring. A potential use case for pump-motors is presented to demonstrate how these various pieces of enabling digital twin technologies may integrated together for online condition monitoring. Challenges and opportunities associated with the pump-motor digital twin enabling technologies are also identified and discussed.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗

Multi‐fidelity digital twin structural model for a sub‐scale downwind wind turbine rotor blade

Abstract This paper presents the development of a multi‐fidelity digital twin structural model (virtual model) of an as‐built wind turbine blade. The goal is to develop and demonstrate an approach to produce an accurate and detailed model of the as‐built blade for use in verifying the performance of the operating two‐bladed, downwind rotor. The digital twin model development methodology, presented herein, involves a novel calibration process to integrate a wide range of information including design specifications, manufacturing information, and structural testing data (modal and static) to produce a multi‐fidelity digital twin structural model: a detailed high‐fidelity model (i.e., 3D finite element analysis [FEA]) and consistent beam‐type models for aeroelastic simulation. A key element is that the multi‐fidelity structural digital twin method follows the rotor from the stages of design, to manufacturing, then to the ground testing and field operation. The result of this comprehensive approach is an accurate multi‐fidelity digital twin structural model for the geometric, structural, and structural dynamic properties of the as‐built blade within a 1% match in mass properties, 3.2% in blade frequencies, and 6% in deflection. The different stages of processing this information within the methodology are discussed. The rotor examined is the SUMR‐Demonstrator (SUMR‐D), which was installed on the Controls Advanced Research Testbed (CART‐2) wind turbine at the National Wind Technology Center. The digital twin model developed here was utilized to design controllers to safely operate SUMR‐D in field tests, which are providing additional data for further evaluation and development of the multi‐fidelity digital twin structural model.

Chetan, Mayank↗

The vector-like twin Higgs

Here, we present a version of the twin Higgs mechanism with vector-like top partners. In this setup all gauge anomalies automatically cancel, even without twin leptons. The matter content of the most minimal twin sector is therefore just two twin tops and one twin bottom. The LHC phenomenology, illustrated with two example models, is dominated by twin glueball decays, possibly in association with Higgs bosons. We further construct an explicit four-dimensional UV completion and discuss a variety of UV completions relevant for both vector-like and fraternal twin Higgs models.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Analysis of T cell receptor repertoire in monozygotic twins concordant and discordant for chronic hepatitis B infection

Highlights: • TCR Repertoire features from twin pairs show heritable bias. • TCR repertoires show antigen biases in chronic viral infection patients. • TCR repertoires show a high level of concordance among HBeAg-positive HBV twins. • Shared clonotypes in identical cured twins show therapeutic potential. Due to their identical inheritance and shared surroundings, identical twins have been the recommended group for studying the susceptibility and prognosis of diseases. Here, CD8{sup +} T cell receptor beta (TCRβ) chains were analyzed by high-throughput sequencing in three pairs of healthy identical twins and chronic hepatitis B patients. The data showed a high level of similarity in the TCR repertoire of each pair in terms of average TCR Vβ segment expression and frequency of the complementary determining region 3 (CDR3) pattern and skewed or oligoclonal clonotypes. Notably, the level of similarity in TCR Vβ expression between the twins appeared to be independent of the consistency or inconsistency of chronic HBV infection, although the detailed CDR3 pattern and frequency were related to disease prognosis. There were more immunodominant clonotypes in patients with HBV antigen seroconversion, which showed an increased abundance. These immunodominant clonotypes may be used as favorable prognostic biomarkers and potential targets for immunotherapy. Thus, delineating the CD8{sup +} T cell repertoire of identical twins with concordant chronic viral infections provides a promising means to screen protective TCR genes for immunotherapy.

60 APPLIED LIFE SCIENCES↗

Effects of carbon nanotubes on twin and texture evolution of magnesium matrix composite during compression process

Highlights: • The CNTs existing at grain boundaries lead to stress concentration, and stimulate the formation of twins. • Crystal rotation and non-basal slip alternately dominate the deformation of the CNTs/Mg composite. • The texture changes from random texture to strong basal texture, strong non-basal texture at the three corresponding stages. • Crystal rotation and non-basal slip system are the main toughening mechanisms of the CNTs/Mg composite. - Abstract: A compression test is performed to investigate the effects of carbon nanotubes (CNTs) on twin and texture evolution of the 1.0 wt.% CNTs reinforced magnesium matrix (CNTs/Mg) composite. The compression process consists of elastic, yield and hardening stages, and the number of twin significantly increases at the yield stage. During the compression process, the crystal rotation and non-basal slip caused by twin shear alternately dominate the deformation of the 1.0 wt.% CNTs/Mg composite. The CNTs existing at grain boundaries lead to stress concentration, and the stress concentration stimulates the formation of twins at the yield stage. The formed twins interact with dislocations, result in crystal rotation and promotion of the non-basal slip system at the hardening stage under the effect of twin shear, thus, improve the toughness of the CNTs/Mg composite.

36 MATERIALS SCIENCE↗

A critical assessment of deformation twinning and epsilon martensite formation in austenitic alloys during complex forming operations

Highlights: • The formation of ε-martensite in TRIP steel reduces formability. • In austenitic alloys, stress induced transformation in addition to twinning and slip does not affect the twinning behaviour. • The volume fraction of twins exhibits variation depending on the strain pathway due to differences in texture development. - Abstract: The effect of mechanical twinning and ε-martensite formation on the formability of austenitic alloys in complex strain pathways has been examined. One of the alloys studied deformed by deformation twinning and slip (TWIP), and this alloy was examined with two grain sizes. The second alloy showed three concurrent deformation modes (slip, TWIP and ε-martensite TRIP). The TWIP/TRIP alloy showed a markedly reduced formability compared to similar alloys, and this has been attributed to a combination of the early development of strain localizations, and the stress-induced formation of ε-martensite. It is suggested that the TRIP effect may not be desirable in high formability sheet steels if the transformation product is ε-martensite. Microstructural examination revealed that the different strain paths develop different twin volume fractions. Plasticity modelling has shown this to be the result of differences in texture development in the different strain paths. In microstructures where slip, TWIP and TRIP can operate concurrently, the stress to activate twinning is unaffected by the additional deformation mode becoming operative.

36 MATERIALS SCIENCE↗

Twinning and martensitic transformations in nickel-enriched 304 austenitic steel during tensile and indentation deformations

Twinning and martensitic transformation have been investigated in nickel-enriched AISI 304 stainless steel subjected to tensile and indentation deformation. Using electron backscatter diffraction (EBSD), the morphology of alpha- and epsilon-martensite and the effect of grain orientation to load axis on phase and structure transformations were analyzed in detail. It was found that the twinning occurred less frequently under indentation than under tension; also, twinning was not observed in [001] and [101] grains. In tensile tests, the martensite particles preferably formed at the deformation twins, intersections between twins, or at twin-grain boundary intersections. Conversely, martensite formation in the indentation tests was not closely associated with twinning; instead, the majority of martensite was concentrated in the dense colonies near grain boundaries. Martensitic transformation seemed to be obstructed in the [001] grains in both tensile and indentation test cases. Under a tensile stress of 800 MPa, both alpha- and epsilon-martensite were found in the microstructure, but at 1100 MPa only -martensite presented in the specimen. Under indentation, alpha- and epsilon-martensite were observed in the material regardless of stress level.

Gussev, Maxim N↗

Study of growth twins produced through heat treatment of fine-grained magnesium

This study investigated the microstructural features of magnesium after the fine-grained magnesium sample was heat treated at 400 °C for 2 h. Both fine-grained and heat-treated magnesium samples were observed using the electron backscatter diffraction technique in scanning electron microscopy. The results show that the grains were substantially coarsened, the local strain and the local misorientation was significantly reduced, and a large number of twins were observed in the heat-treated magnesium sample. The misorientation angle analysis determined that the twins were oriented about 86.3° away from the orientation of their corresponding matrices, and the twins were the variants of $\{1 0 \bar{1} 2\}$ tensile twins. The relative orientation analysis also identified that the fast growth directions of the twins were closely along the $<2 \bar{1} \bar{1} 0>$ or $<1 0 \bar{1} 0>$ directions in the basal plane. The twins can merge or impinge onto each other. Most boundaries between the twins have the misorientation angle of about 7.4°.

36 MATERIALS SCIENCE↗

Suppression of Rotational Twins in Epitaxial B 12 P 2 on 4H-SiC

B 12 P2 was grown epitaxially on (0001) 4H-SiC using two different substrate miscuts: a standard 4° miscut toward the [$11\bar{20}$] and a custom miscut 4° toward the [$1\bar{10}0$]. Epitaxy on substrates miscut to the [$11\bar{20}$] resulted in highly twinned B 12 P 2 films with a rotational twin density of approximately 70% twin orientation I and 30% twin orientation II. In contrast, epitaxy on substrates tilted toward the [$1\bar{10}0$] produced films of >99% twin orientation I. A H 2 etch model is used to explain the 4H-SiC surface morphology for each miscut prior to epitaxy and demonstrate how the surface steps influence the nucleation of B 12 P 2 twin orientations. Surface steps on substrates miscut to the [$11\bar{20}$] tend to be zig-zagged with steps rotated 60° from one another producing B 12 P 2 crystals that nucleate in orientations rotated by 60°, hence forming rotationally twinned films. In conclusion, steps on substrates tilted to the [$1\bar{10}0$] tend to be parallel resulting in crystallographically aligned B 12 P 2 nucleation.

36 MATERIALS SCIENCE↗

Dislocation mechanisms and 3D twin architectures generate exceptional strength-ductility-toughness combination in CrCoNi medium-entropy alloy

Combinations of high strength and ductility are hard to attain in metals. Exceptions include materials exhibiting twinning-induced plasticity. To understand how the strength-ductility trade-off can be defeated, we apply in situ, and aberration-corrected scanning, transmission electron microscopy to examine deformation mechanisms in the medium-entropy alloy CrCoNi that exhibits one of the highest combinations of strength, ductility and toughness on record. Ab initio modelling suggests that it has negative stacking-fault energy at 0K and high propensity for twinning. With deformation we find that a three-dimensional (3D) hierarchical twin network forms from the activation of three twinning systems. This serves a dual function: conventional twin-boundary (TB) strengthening from blockage of dislocations impinging on TBs, coupled with the 3D twin network which offers pathways for dislocation glide along, and cross-slip between, intersecting TB-matrix interfaces. The stable twin architecture is not disrupted by interfacial dislocation glide, serving as a continuous source of strength, ductility and toughness.

36 MATERIALS SCIENCE↗

Deformation twinning and grain partitioning in a hexagonal close-packed magnesium alloy

Pervasive deformation twinning in magnesium greatly affects its strength and formability. The local stress fields associated with twinning play a key role on deformation behavior and fracture but are extremely difficult to characterize experimentally. In this study, we perform synchrotron experiments with differential-aperture X-ray microscopy to measure the 3D stress fields in the vicinity of a twin with a spatial resolution of 0.5 micrometer. The measured local stress field aids to identify the sequence of events involved with twinning. We find that the selected grain deforms elastically before twinning, and the twin formation splits the grain into two non-interacting domains. Under further straining one domain of the grain continued to deform elastically, whereas the other domain deforms plastically by prismatic slip. This heterogeneous deformation behavior may be mediated by the surrounding medium and it is likely to lead to asymmetric twin growth.

36 MATERIALS SCIENCE↗

Review of low-cost self-driving laboratories in chemistry and materials science: the “frugal twin” concept

This review proposes the concept of a “frugal twin,” similar to a digital twin, but for physical experiments. Frugal twins range from simple toy examples to low-cost surrogates of high-cost research systems. For example, a color-mixing self-driving laboratory (SDL) can serve as a low-cost version of a costly multi-step chemical discovery SDL. Frugal twins already provide hands-on experience for SDLs with low costs and low risks. They can also offer as test beds for software prototyping (e.g., optimization, data infrastructure), and a low barrier to entry for democratizing SDLs. However, there is room for improvement. The true value of frugal twins can be realized in three core areas. Firstly, hardware and software modularity; secondly, purpose-built design (human-inspired vs. hardware-centric vs. human-in-the-loop); and thirdly state-of-the-art (SOTA) software (e.g., multi-fidelity optimization). We also describe the ethical benefits and risks that come with the democratization of science through frugal twins. For future work, we suggest ideas for new frugal twins, SDL educational course outcomes, and a classification scheme for autonomy levels.

36 MATERIALS SCIENCE↗

Single Crystal Plasticity Model with Deformation Twinning for the High Rate Deformation of β-HMX

Deformation twinning is an active deformation mechanism during loading along certain crystallographic directions of β-cyclotetramethylene tetranitramine (β-HMX). In this work, a finite strain thermomechanical model is extended to include twinning as a deformation mechanism in addition to plastic slip. The stress is derived from the free energy expression including a term representing the equation of state. The crystal plasticity framework is used to divide the total strain into inelastic and elastic component, where the elastic part is used in the expression for the free energy. The twin systems are treated as pseudo slip systems and the shear rate on the twin systems is evaluated in terms of the twin resistance and the projection of the stress tensor. The model parameters were calibrated against a set of plate impact experiments performed on β-HMX by Dick et al. The remaining plate impact experiments are used to evaluate the predictive capability of the model. The quality of the model fits and predictions is discussed from a physical and modeling perspective. Particularly, the role of twin modeling on results is highlighted. Finally, the model is used to explore the relationship between the propensity for twinning and crystal orientation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

THE 'TWIN-CME' SCENARIO AND LARGE SOLAR ENERGETIC PARTICLE EVENTS IN SOLAR CYCLE 23

Energetic particles in large solar energetic particle (SEP) events are a major concern for space weather. Recently, Li et al. proposed a 'twin-CME' scenario for ground-level events. Here we extend that study to large SEP events in solar cycle 23. Depending on whether preceding coronal mass ejections (CMEs) within 9 hr exist and whether ions >10 MeV nucleon{sup -1} exceed 10 pfu, we categorize fast CMEs with speed >900 km s{sup -1} and width >60 Degree-Sign from the western hemisphere source regions into four groups: groups I and II are 'twin' and single CMEs that lead to large SEPs; groups III and IV are 'twin' and single CMEs that do not lead to large SEPs. The major findings of this paper are: first, large SEP events tend to be 'twin-CME' events. Of 59 western large SEP events in solar cycle 23, 43 are 'twin-CME' (group I) events and 16 are single-CME (group II) events. Second, not all 'twin CMEs' produced large SEPs: 28 twin CMEs did not produce large SEPs (group III events). Some of them produced excesses of particles up to a few MeV nucleon{sup -1}. Third, there were 39 single fast CMEs that did not produce SEPs (group IV events). Some of these also showed an excess of particles up to a few MeV nucleon{sup -1}. For all four groups of events, we perform statistical analyses on properties such as the angular width, the speed, the existence of accompanying metric type II radio bursts, and the associated flare class for the main CMEs and the preceding CMEs.

79 ASTRONOMY AND ASTROPHYSICS↗

Testing the role of AGN on the star formation and metal enrichment of ‘twin galaxies’

Here, we explore the effect of AGN activity on the star formation history of galaxies by analysing the stellar population properties of 10 pairs of nearby twin galaxies – selected as being visually similar except for the presence of an AGN. The selection of such twin samples represents a method to study AGN feedback, as recently proposed by del Moral Castro et al. We use integral field unit (IFU) data from CALIFA, stacked within three fixed apertures. AGN galaxies in a twin pair suggest more evolved stellar populations than their non-AGN counterpart 90 per cent of the time, regardless of aperture size. A comparison with a large sample from SDSS confirms that most twins are representative of the general population, but in each twin the differences between twin members is significant. A set of targeted line strengths reveal the AGN member of a twin pair is older and more metal-rich than the non-AGN galaxy, suggesting AGN galaxies in our sample may either have an earlier formation time or follow a different star formation and chemical enrichment history. These results are discussed within two simple, contrasting hypotheses for the role played by AGN in galaxy evolution, which can be tested in the future at a greater detail with the use of larger data sets.

79 ASTRONOMY AND ASTROPHYSICS↗

Technical Challenges and Gaps in Integration of Advanced Sensors, Instrumentation, and Communication Technologies with Digital Twins for Nuclear Application

This paper explores integrating advanced sensor, instrumentation, and communication technologies with digital twin technologies for nuclear energy application. Digital twins and digital-twin-enabling technologies are expected to integrate with future nuclear reactor designs and have the potential to impact currently operating nuclear power plants. Greater digital integration, advanced instrumentation and control systems, and advanced operations and maintenance practices are all associated with digital-twin-enabling technologies. Advanced sensors, instrumentation, and communication technology are expected to comprise important elements of the infrastructure required to develop and operate a nuclear digital twin system. This paper identifies and discusses challenges and gaps in developing and implementing advanced sensors and instrumentation and communication technology to be integrated with a digital twin in current and advanced reactor applications. It is important to address some challenge and gap to enable a successful near-term deploying advanced sensors, instrumentation, and communication technologies integrated with digital twins.

Yadav, Vaibhav↗