Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THERMOPLASTICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

FIBER ORIENTATION IN INJECTION MOLDED LONG CARBON FIBER THERMOPLASTIC COMPOSITES

A set of edge-gated and center-gated plaques were injection molded with long carbon fiber-reinforced thermoplastic composites, and the fiber orientation was measured at different locations of the plaques. Autodesk Simulation Moldflow Insight (ASMI) software was used to simulate the injection molding of these plaques and to predict the fiber orientation, using the anisotropic rotary diffusion and the reduced strain closure models. The phenomenological parameters of the orientation models were carefully identified by fitting to the measured orientation data. The fiber orientation predictions show very good agreement with the experimental data.

carbon fiber↗
DOE OSTI2022

Bio-Optimized Technologies to Keep Thermoplastics out of Landfills and the Environment (BOTTLE)

Plastics have revolutionized modern life, but reliance on these fossil-based materials that persist for centuries is causing a pollution crisis and contributing to greenhouse gas (GHG) emissions. To develop new technologies to address this problem, the Bio-Optimized Technologies to keep Thermoplastics out of Landfills and the Environment (BOTTLE) Consortium will deliver selective, scalable technologies to enable cost-effective recycling, upcycling, and increased energy efficiency. BOTTLE is an interdisciplinary team of experts that aim to develop selective, scalable processes to deconstruct and upcycle today's plastics and thermosets, redesign tomorrow's plastics to be recyclable-by-design (RBD) and derived from both bio-based and plastic waste-based feedstocks, work with industrial partners across the value chain to catalyze the circular economy for plastics, and leverage AMO and BETO investments in analysis-guided R&D, integrated process development, chemical and biological catalysis, materials characterization, modeling, and data science. BOTTLE is guided by techno-economic analysis (TEA) and supply chain-based life-cycle assessment (LCA). BOTTLE comprises members from ten partner institutions. Primary outcomes to date include establishment of a full consortium, impactful, benchmarking analyses that will be important for the plastics recycling and upcycling community, and multiple impactful, high-impact publications across the breadth of our research portfolio.

bio-optimized↗
DOE OSTI2016

A new class of renewable thermoplastics with extraordinary performance from nanostructured lignin-elastomers

In this study, a new class of thermoplastic elastomers has been created by introducing nanoscale-dispersed lignin (a biomass-derived phenolic oligomer) into nitrile rubber. Temperature-induced controlled miscibility between the lignin and the rubber during high shear melt-phase synthesis allows tuning the material s morphology and performance. The sustainable product has unprecedented yield stress (15–45 MPa), strain hardens at large deformation, and has outstanding recyclability. The multiphase polymers developed from an equal-mass mixture of a melt-stable lignin fraction and nitrile rubber with optimal acrylonitrile content, using the method described here, show 5–100 nm lignin lamellae with a high-modulus rubbery interphase. Molded or printed elastomeric products prepared from the lignin-nitrile material offer an additional revenue stream to pulping mills and biorefineries. Research was sponsored by the Technology Innovation Program of Oak Ridge National Laboratory, managed by UT-Battelle, LLC, for the U.S. Department of Energy. TEM (J.C. and C.D.T.) and SAXS (J.K.K.) experiments were conducted at the Center for Nanophase Materials Sciences, which is a DOE Office of Science User Facility.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Thermoplastic Polyurethanes with Isosorbide Chain Extender

Isosorbide, a renewable diol derived from starch, was used alone or in combination with butane diol (BD) as the chain extender in two series of thermoplastic polyurethanes (TPU) with 50 and 70% polytetramethylene ether glycol (PTMEG) soft segment concentration (SSC), respectively. In the synthesized TPUs, the hard segment composition was systematically varied in both series following BD/isosorbide molar ratios of 100 : 0; 75 : 25; 50 : 50; 25 : 75, and 0 : 100 to examine in detail the effect of chain extenders on properties of segmented polyurethane elastomers with different morphologies. We found that polyurethanes with 50% SSC were hard elastomers with Shore D hardness of around 50, which is consistent with assumed co-continuous morphology. Polymers with 70% SSC displayed lower Shore A hardness of 74–79 (Shore D around 25) as a result of globular hard domains dispersed in the soft matrix. Insertion of isosorbide increased rigidity, melting point and glass transition temperature of hard segments and tensile strength of elastomers with 50% SSC. These effects were weaker or non-existent in 70% SSC series due to the short hard segments and low content of isosorbide. We also found that the thermal stability was lowered by increasing isosorbide content in both series.

elastomers↗
DOE OSTI2024

A novel digital lifecycle for Material‐Process‐Microstructure‐Performance relationships of thermoplastic olefins foams manufactured via supercritical fluid assisted foam injection molding

Abstract This research significantly enhances the applicability of thermoplastic olefins (TPOs) in the automotive industry using supercritical N 2 as a physical foaming agent, effectively addressing the limitations of traditional chemical agents. It merges experimental results with simulations to establish detailed material‐process‐microstructure‐performance (MP2) relationships, targeting 5–20% weight reductions. This innovative approach labeled digital lifecycle (DLC) helps accurately predict tensile, flexural, and impact properties based on the foam microstructure, along with experimentally demonstrating improved paintability. The study combines process simulations with finite element models to develop a comprehensive digital model for accurately predicting mechanical properties. Our findings demonstrate a strong correlation between simulated and experimental data, with about a 5% error across various weight reduction targets, marking significant improvements over existing analytical models. This research highlights the efficacy of physical foaming agents in TPO enhancement and emphasizes the importance of integrating experimental and simulation methods to capture the underlying foaming mechanism to establish material‐process‐microstructure‐performance (MP2) relationships. Highlights Establishes a material‐process‐microstructure‐performance (MP2) for TPO foams Sustainably produces TPO foams using supercritical (ScF) N 2 with 20% lightweighting Shows enhanced paintability for TPO foam improved surface aesthetics Digital lifecycle (DLC) that predicts both foam microstructure and properties DLC maps process effects & microstructure onto FEA mesh for precise prediction

Engineering↗
DOE OSTI2018

Quasi‐Solid‐State Dye‐Sensitized Solar Cells Containing a Charged Thermoplastic Elastomeric Gel Electrolyte and Hydrophilic/phobic Photosensitizers

As the threat of global climate change due to combustion emissions becomes increasingly alarming, the search for clean and sustainable alternative energy is of paramount importance. With this objective in mind, harnessing solar energy is particularly attractive due to ongoing improvements in silicon‐, perovskite‐, and organic‐based solar cells. Of these, dye‐sensitized solar cells (DSSCs) constitute a promising technology due to their relatively low cost, moderate conversion efficiency, and robust mechanical properties. An important breakthrough in the development of DSSCs is the use of polymer gel electrolytes. In this work, we employ amphi­philic thermoplastic elastomers (TPEs) in the form of sulfonated block ionomer (SBI) homologs for this purpose. Since the midblock of each charged copolymer is hydrophilic, the resultant microphase‐separated nanostructures consist of continuous ionic channels that facilitate electron diffusion. A unique characteristic of the SBI archetype studied here is that the morphology can be solvent‐templated. We exploit this feature by introducing either hydrophilic or hydrophobic photosensitizers into the DSSCs. When the SBI exhibits a primarily lamellar morphology, a hydrophilic dye yields the highest efficiency (7.0%), whereas the opposite is observed when the nanostructure consists of a solvent‐templated nonpolar matrix. Photosensi­tizer tunability is augmented by the intrinsic mechanical and adhesive properties of a TPE.

Al‐Mohsin, Heba A.↗
DOE OSTI2025

Fused filament fabrication of thermoplastic polyurethane composites with microencapsulated phase-change material

Here, the present study examines the thermal energy storage (TES) effectiveness and printability of microencapsulated phase-change material (MEPCM) combined with thermoplastic polyurethane (TPU) for fused filament fabrication (FFF). Two formulations were assessed: 24D MEPCM, which changes phase at 24 ° C, compounded with TPU pellets and 43D MEPCM, which changes phase at 43 ° C, integrated with TPU powder. These combinations are designed to evaluate the effectiveness of the form of the TPU (pellets versus powder) in the FFF process. The investigation includes a comprehensive analysis of thermal characteristics, encompassing phase-change temperature, latent heat of fusion, thermal conductivity, and thermal decomposition, which are assessed through differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Additionally, mechanical properties, including stress-strain behavior, are examined to evaluate material suitability for TES applications, while microstructural visualization is used to provide deeper insights into material performance, structural integrity, and the quality of printed components. The 24D MEPCM and TPU pellets formulation experienced a significant loss of approximately 39.6% of PCM during filament extrusion and printing, resulting in a reduced effective latent heat. Therefore, further characterization of the pellet formulation was discontinued due to excessive leakage. In contrast, the 43D MEPCM and TPU powder formulation demonstrated minimal PCM loss, with the 60 wt.% composition achieving an effective latent heat of 132 J/g. This value represents the highest effective latent heat currently documented in the literature for PCM-polymer-composite materials produced using an FFF-based additive manufacturing process.

25 ENERGY STORAGE↗
DOE OSTI2020

Effect of 3D printing conditions on the micro- and macrostructure and properties of high-performance thermoplastic composites

Within the scope of extrusion based additive manufacturing, this chapter provides a review of the research in understanding the physical relationships between microstructure variables and macrostructure properties of high-performance thermoplastic polymers. The development of interlayer strength has been discussed based on the theory of inter-diffusion and re-entanglement of polymer chains at interface. The observations from the study in joining and direct-bonding of polymer surfaces provide insights into the mechanisms of the formation of interface between adjacent layers. Quantitative prediction of interfacial strength as a function of processing temperature and contact time is presented. The mechanisms that lead to reduced mechanical strength at the interface are discussed. The second half of the chapter outlined a set of printing conditions and their influence on structural properties.

Liu, Peng↗
DOE OSTI2021

Melt extruded versus extrusion compression molded glass-polypropylene long fiber thermoplastic composites

Long fiber thermoplastic (LFT) composites are processed either with extrusion compression or fiber injection processes. The properties of LFT materials are highly influenced by processing techniques, which lead to different porosity contents, fiber length distributions, and fiber orientation distributions. It is important to understand the various LFT processing techniques and their effects on mechanical, thermal, and microscopic properties. This work considered LFT sheets processed via extrusion, which offers highly aligned fibers (referred to as “Tecnogor composites”), and LFT composites produced via extrusion compression molding (ECM), which offers a random distribution of fibers. Tecnogor composites exhibited higher flexural strength (35–65%), flexural modulus (132–172%), tensile strength (39–52%), tensile modulus (67–75%), and Izod impact resistance (195–220%) than the random LFT composites. This response was attributed to the aligned fibers in Tecnogor composites. Mathematical models including Halpin-Tsai and Lavengood-Goettler were used to predict and compare the Young’s modulus of Tecnogor and ECM composites, respectively.

mechanical testing↗
DOE OSTI2023

Conductive overbraid of continuous fiber thermoplastic composite tows

Here, to meet the increasing demand for lightweight materials with multifunctional capabilities, a new high-rate manufacturing method and material system, referred to as M-TOW ® (multifunctional-tow) is introduced. Overbraiding is used to incorporate highly conductive wire onto the continuous fiber reinforced tow (M-TOW ® ), offering a solution for integrating thermal and electrical conductivity into hybrid-molded composite structures. The conductivity performance of different wire configurations are compared before and after forming the M TOW ® , measuring electrical conductivities up to 5.5 x 10 5 S / cm and thermal conductivities up to 21 W / mK. Results conclude that the integration of conductive wires into thermoplastic preforms is a viable means of expanding the functionality of lightweight, high strength composite structures.

3-dimensional reinforcement↗
DOE OSTI2024

Examining infrared thermography based approaches to rapid fatigue characterization of additively manufactured compression molded short fiber thermoplastic composites

A novel additive manufacturing (AM) methodology combined with a compression molding (CM) process has been developed to optimize the microstructure of short fiber thermoplastic composites (SFTs)with higher fiber alignment and lower porosity, yielding superior stiffness, strength, and structural integrity. Here, the current work examines the efficacy of the ‘passive’ infrared thermography (IRT) techniques for rapid fatigue characterization of SFTs that use the surface temperature evolution during cyclic loading due to self-heating as a fatigue indicator. A comparison of fatigue limits obtained from traditional stress-life (SN) (≈53.1%σ uts ) and IRT (≈54.1%σ uts ) shows a close match. However, the SN curve required 18 specimens and two weeks of continuous cyclic testing, while IRT used three specimens with 5 hours of testing. Thus, the IRT approach provides an accelerated testing framework for rapidly estimating the fatigue limit. Additionally, existing phenomenological approaches to IRT fatigue characterization have been examined.

42 ENGINEERING↗
DOE OSTI2025

Fast-rate joining of thermoplastic composites using integrated additive manufacturing and compression molding process

The integration of additive manufacturing (AM) technology with compression molding (CM), has emerged as a high-performance composite manufacturing technology in recent years. In the AM-CM process, quickly deposited AM preform on a mold undergoes a rapid compaction cycle to fabricate structurally robust composite parts due to highly controlled fiber alignment (from AM) and reduced porosity (from CM). Currently, AMCM-based part size is limited by the size of the mold volume, thus posing a challenge to manufacture scalable parts. Here, this work focuses on joining techniques developed to enable fast rate joining of short fiber-reinforced thermoplastic composite parts using the AM-CM process. Acrylonitrile butadiene styrene resin reinforced with 20 wt% short carbon fiber composites was printed onto a flat mold and pressed under a hydraulic press. Fabricated panels were joined by the (a) mechanical impression at the joining interface and (b) over-molded continuous carbon fiber (CCF) sheet. Tensile tests were performed to characterize the joining strength of both mechanical impression-based joints and CCF over molded joints. Among the mechanical impression-based joints, a U-shape channel allowed the fibers to flow between two joint parts, and 280 % increased mechanical properties were observed. The continuous carbon fiber-based over molded joint CCF showed 350 % increase in tensile strength compared to the butt joints.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of natural carbon filler on thermo-oxidative degradation of thermoplastic-based composites

Here thermo-oxidative degradation of thermoplastic-based composites filled with two types of carbon filler including bituminous (Pittsburgh No.8, P8) and sub-bituminous (Powder River Basin, PRB) coals were investigated using differential scanning calorimetry (DSC) and thermogravimetric analysis. Oxidation induction time (OIT) and activation energy (AE) for coal plastic composites (CPCs), HDPE, and commercially available wood plastic composites (WPCs) were determined using isothermal and isoconversional kinetic methods. OIT values for CPC increased with coal content, indicating higher thermo-oxidative stability. AE values obtained using isothermal method were 52–116 kJ/mol for all CPC formulations, 32 kJ/mol for HDPE, and 33–114 kJ/mol for WPCs. AEs for CPCs obtained using isoconversional methods were not constant but rather dependent on the degree of degradation with CPC/ P8 coal possessing higher overall AE. Incorporating coal into HDPE increased thermo-oxidative stability of the resulting composite, indicating coal potentially acts as a natural primary and secondary antioxidant for polymer materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Strong, Resilient, and Sustainable Aliphatic Polyester Thermoplastic Elastomers

Thermoplastic elastomers (TPEs) composed of ABA block polymers exhibit a wide variety of properties and are easily processable as they contain physical, rather than chemical, cross-links. Poly(γ-methyl-ε-caprolactone) (PγMCL) is an amorphous polymer with a low entanglement molar mass (M e = 2.9 kg mol –1 ), making it a suitable choice for tough elastomers. Incorporating PγMCL as the midblock with polylactide (PLA) end blocks (f LA = 0.17) results in TPEs with high stresses and elongations at break (σ B = 24 ± 2 MPa and ε B = 1029 ± 20%, respectively) and low levels of hysteresis. The use of isotactic PLA as the end blocks (f LLA = 0.17) increases the strength and toughness of the material (σ B = 30 ± 4 MPa, ε B = 988 ± 30%) due to its semicrystalline nature. This study aims to demonstrate how the outstanding properties in these sustainable materials are a result of the entanglements, glass transition temperature, segment–segment interaction parameter, and crystallinity, resulting in comparable properties to the commercially relevant styrene-based TPEs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Asymmetric Miktoarm Star Polymers as Polyester Thermoplastic Elastomers

A library of polyester-based A(BA') n asymmetric miktoarm star polymers was synthesized with A, A' = poly(l-lactide) (PLLA) as the semicrystalline hard blocks and B = poly(4-methylcaprolactone) (PMCL) as the soft segment using a grafting-through platform known as μSTAR. The synthetic versatility of μSTAR enabled a systematic investigation of architectural design parameters, in particular the number of BA' arms (n), while holding the A, A', and B block lengths constant. The value of n has a pronounced impact on the mechanical properties of these high-molecular-weight miktoarm materials. Tensile toughness increases with n, an effect likely related to bridging, as the modulus drops because the hard-block volume fraction decreases. Furthermore, these insights expand our understanding of architecture effects in sustainable thermoplastic elastomers.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synthesis, Properties, and Metathesis Activity of Polyurethane Thermoplastics and Thermosets from a Renewable Polysesquiterpene Diol

Polyurethanes (PUs) are the sixth most commonly utilized plastic class, yet ∼80% of commodity material is landfilled or incinerated at the end of life. Disposal of thermosets is particularly problematic as cross-linking prevents the repurposing of disposed material. Thus, there is considerable interest in the development of PUs derived from inexpensive feedstocks that can be inherently chemically deconstructed. Ring opening metathesis polymerization (ROMP) of the naturally occurring sesquiterpene β-caryophyllene in the presence of dihydroxy chain terminators afforded the polyol hydroxy-terminated polycaryophyllene (HTPCR). Incorporation of HTPCR into PUs through reaction with polyisocyanates produced polymers with thermal and rheological properties comparable to commodity materials. The feasibility of chemical degradation of both thermoplastic and thermoset materials was also demonstrated through ruthenium-mediated metathesis, utilizing the metathesis-active olefins within the repeat caryophyllene monomer unit. Overall, this work highlights the value of biorenewable, chemically reprocessable polysesquiterpenes in the PU space.

materials↗
DOE OSTI2023

Revealing Deformation Mechanisms in Polymer-Grafted Thermoplastic Elastomers via In Situ Small-Angle X-ray Scattering

The tunable properties of thermoplastic elastomers (TPEs), through polymer chemistry manipulations, enable these technologically critical materials to be employed in a broad range of applications. The need to “dial-in” the mechanical properties and responses of TPEs generally requires the design and synthesis of new macromolecules. In these designs, TPEs with nonlinear macromolecular architectures outperform the mechanical properties of their linear copolymer counterparts, but the differences in the deformation mechanism providing enhanced performance are unknown. Here, in situ small-angle X-ray scattering (SAXS) measurements during uniaxial extension reveal distinct deformation mechanisms between a commercially available linear poly(styrene)–poly(butadiene)–poly(styrene) (SBS) triblock copolymer and the grafted SBS version containing grafted poly(styrene) (PS) chains from the poly(butadiene) (PBD) midblock. The neat SBS (φ SBS = 100%) sample deforms congruently with the macroscopic dimensions, with the domain spacing between spheres increasing and decreasing along and transverse to the stretch direction, respectively. At high extensions, end segment pullout from the PS-rich domains is detected, which is indicated by a disordering of SBS. Conversely, the PS-grafted SBS that is 30 vol % SBS and 70% styrene (φ SBS = 30%) exhibits a lamellar morphology, and in situ SAXS measurements reveal an unexpected deformation mechanism. During deformation, there are two simultaneous processes: significant lamellar domain rearrangement to preferentially orient the lamellae planes parallel to the stretch direction and crazing. The samples whiten at high strains as expected for crazing, which corresponds with the emergence of features in the 2D SAXS pattern during stretching consistent with fibril-like structures that bridge the voids in crazes. The significant domain rearrangement in the grafted copolymers is attributed to the new junctions formed across multiple PS domains by the grafting of a single chain. In conclusion, the in situ SAXS measurements provide insights into the enhanced mechanical properties of grafted copolymers that arise through improved physical cross-linking that leads to nanostructure domain reorientation for self-reinforcement and craze formation where fibrils help to strengthen the polymer.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Corrosion Resistance of Lignin-Based Thermoplastic Adhesive-Bonded Aluminum Joints

Adhesive-bonded joints are essential for lightweight, multimaterial automotive structures. We developed a lignin-based thermoplastic adhesive with adhesion strength comparable to conventional epoxy adhesives (20–23 MPa), while offering exceptional durability, recyclability, and corrosion resistance. Unlike commercial epoxy adhesives requiring refrigerated storage, our adhesive retains its bonding potential after a year of ambient conditioning. Bonded joints can be repeatedly disassembled and rejoined with less than 2% strength loss. After 500 h of salt fog exposure, the adhesive-bonded aluminum joints exhibited a 24% strength reduction, compared to 61% reduction in strength of joints based on a commercial epoxy adhesive.

Yu, Zeyang [ORNL] (ORCID:0000000209002374)↗