Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Static analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Analysis of Fluctuating Static Pressure Measurements in a Large High Reynolds Number Transonic Cryogenic Wind Tunnel

Dynamic measurements of fluctuating static pressure levels were made using flush mounted high frequency response pressure transducers at eleven locations in the circuit of the National Transonic Facility (NTF) over the complete operating range of this wind tunnel. Measurements were made at test section Mach numbers from 0.2 to 1.2, at pressure from 1 to 8.6 atmospheres and at temperatures from ambient to -250 F, resulting in dynamic flow disturbance measurements at the highest Reynolds numbers available in a transonic ground test facility. Tests were also made independently at variable Mach number, variable Reynolds number, and variable drivepower, each time keeping the other two variables constant thus allowing for the first time, a distinct separation of these three important variables. A description of the NTF emphasizing its flow quality features, details on the calibration of the instrumentation, results of measurements with the test section slots covered, downstream choke, effects of liquid nitrogen injection and gaseous nitrogen venting, comparisons between air and nitrogen, isolation of the effects of Mach number, Reynolds number, and fan drive power, and identification of the sources of significant flow disturbances is included. The results indicate that primary sources of flow disturbance in the NTF may be edge-tones generated by test section sidewall re-entry flaps and the venting of nitrogen gas from the return leg of the tunnel circuit between turns 3 and 4 in the cryogenic mode of operation. The tests to isolate the effects of Mach number, Reynolds number, and drive power indicate that Mach number effects predominate. A comparison with other transonic wind tunnels shows that the NTF has low levels of test section fluctuating static pressure especially in the high subsonic Mach number range from 0.7 to 0.9.

Igoe, William B.↗

Analysis of Fluctuating Static Pressure Measurements in the National Transonic Facility

Dynamic measurements of fluctuating static pressure levels were taken with flush-mounted, high-frequency response pressure transducers at 11 locations in the circuit of the National Transonic Facility (NTF) across the complete operating range of this wind tunnel. Measurements were taken at test-section Mach numbers from 0.1 to 1.2, at pressures from 1 to 8.6 atm, and at temperatures from ambient to -250 F, which resulted in dynamic flow disturbance measurements at the highest Reynolds numbers available in a transonic ground test facility. Tests were also made by independent variation of the Mach number, the Reynolds number, or the fan drive power while the other two parameters were held constant, which for the first time resulted in a distinct separation of the effects of these three important parameters.

Igoe, William B.↗

A Simplistic Look at Limit Stresses from Random Loading

Utilizing a continuous beam model, this report compares the potential stresses imposed on the beam from a random environment with those resulting from a typical static load analysis or test simulation. The Miles' equation used to develop peak response accelerations is shown to become a force equation in the hands of strength assessment personnel. This may prove to be unrealistic since hardware dynamic stresses are related to deflection rather than load. Correlation of the stress state for any static analysis or test with the actual dynamic response stress is strictly dependent upon how well the static deflections simulate the predominant dynamic mode shape. The report proposes that the general shape of this predominant mode, along with the peak response accelerations of major masses be used in strength assessments. From these data, a tailored enforced displacement loading may prove to be more effective in reproducing random induced stresses on flight hardware.

Lee, H. M.↗

Test stand design and analysis for Titan 34D static firing

The Test Stand 1C at the Air Force Astronautic Laboratory (AFAL), Edwards AFB, Calif., was originally designed for F-1 liquid propellant engines. The stand was modified to handle a five and one half segment Solid Rocket Motor (SRM) Titan 34D vertical static firing test. The main design drivers and analysis effort utilized in the modification of the test stand are discussed.

Pazargadi, Shayan↗

Reliability analysis of composite structures

A probabilistic static stress analysis methodology has been developed to estimate the reliability of a composite structure. Closed form stress analysis methods are the primary analytical tools used in this methodology. These structural mechanics methods are used to identify independent variables whose variations significantly affect the performance of the structure. Once these variables are identified, scatter in their values is evaluated and statistically characterized. The scatter in applied loads and the structural parameters are then fitted to appropriate probabilistic distribution functions. Numerical integration techniques are applied to compute the structural reliability. The predicted reliability accounts for scatter due to variability in material strength, applied load, fabrication and assembly processes. The influence of structural geometry and mode of failure are also considerations in the evaluation. Example problems are given to illustrate various levels of analytical complexity.

Kan, Han-Pin↗

Accelerated development and flight evaluation of active controls concepts for subsonic transport aircraft. Volume 2: AFT C.G. simulation and analysis

Relaxed static stability and stability augmentation with active controls were investigated for subsonic transport aircraft. Analytical and simulator evaluations were done using a contemporary wide body transport as a baseline. Criteria for augmentation system performance and unaugmented flying qualities were evaluated. Augmentation control laws were defined based on selected frequency response and time history criteria. Flying qualities evaluations were conducted by pilots using a moving base simulator with a transport cab. Static margin and air turbulence intensity were varied in test with and without augmentation. Suitability of a simple pitch control law was verified at neutral static margin in cruise and landing flight tasks. Neutral stability was found to be marginally acceptable in heavy turbulence in both cruise and landing conditions.

Urie, D. M.↗

Static and dynamic helicopter airframe analysis with NASTRAN

The use of NASTRAN at Bell Helicopter Company for structural static and dynamic analysis of a helicopter airframe is described. Analysis of airframe internal loads, main rotor isolation systems, and airframe vibration is discussed. The use of each rigid format for these types of analysis is summarized. Suggested improvements to NASTRAN to increase its effectiveness in performing helicopter airframe analysis are given.

Wilson, H. E.↗

An easily implemented static condensation method for structural sensitivity analysis

A black-box approach to static condensation for sensitivity analysis is presented with illustrative examples of a cube and a car structure. The sensitivity of the structural response with respect to joint stiffness parameter is calculated using the direct method, forward-difference, and central-difference schemes. The efficiency of the various methods for identifying joint stiffness parameters from measured static deflections of these structures is compared. The results indicate that the use of static condensation can reduce computation times significantly and the black-box approach is only slightly less efficient than the standard implementation of static condensation. The ease of implementation of the black-box approach recommends it for use with general-purpose finite element codes that do not have a built-in facility for static condensation.

Gangadharan, S. N.↗

Static Aeroelastic Scaling and Analysis of a Sub-Scale Flexible Wing Wind Tunnel Model

This paper presents an approach to the development of a scaled wind tunnel model for static aeroelastic similarity with a full-scale wing model. The full-scale aircraft model is based on the NASA Generic Transport Model (GTM) with flexible wing structures referred to as the Elastically Shaped Aircraft Concept (ESAC). The baseline stiffness of the ESAC wing represents a conventionally stiff wing model. Static aeroelastic scaling is conducted on the stiff wing configuration to develop the wind tunnel model, but additional tailoring is also conducted such that the wind tunnel model achieves a 10% wing tip deflection at the wind tunnel test condition. An aeroelastic scaling procedure and analysis is conducted, and a sub-scale flexible wind tunnel model based on the full-scale's undeformed jig-shape is developed. Optimization of the flexible wind tunnel model's undeflected twist along the span, or pre-twist or wash-out, is then conducted for the design test condition. The resulting wind tunnel model is an aeroelastic model designed for the wind tunnel test condition.

Aeroelasticity↗

BEST3D user's manual: Boundary Element Solution Technology, 3-Dimensional Version 3.0

The theoretical basis and programming strategy utilized in the construction of the computer program BEST3D (boundary element solution technology - three dimensional) and detailed input instructions are provided for the use of the program. An extensive set of test cases and sample problems is included in the manual and is also available for distribution with the program. The BEST3D program was developed under the 3-D Inelastic Analysis Methods for Hot Section Components contract (NAS3-23697). The overall objective of this program was the development of new computer programs allowing more accurate and efficient three-dimensional thermal and stress analysis of hot section components, i.e., combustor liners, turbine blades, and turbine vanes. The BEST3D program allows both linear and nonlinear analysis of static and quasi-static elastic problems and transient dynamic analysis for elastic problems. Calculation of elastic natural frequencies and mode shapes is also provided.

Source record↗

Parallel Aeroelastic Analysis Using ENSAERO and NASTRAN

A high fidelity parallel static structural analysis capability is created and interfaced to the multidisciplinary analysis package ENSAERO-MPI of Ames Research Center. This new module replaced ENSAERO's lower fidelity simple finite element and modal modules. Full aircraft structures may be more accurately modeled using the new finite element capability. Parallel computation is performed by breaking the full structure into multiple substructures. This approach is conceptually similar to ENSAERO's multi-zonal fluid analysis capability. The new substructure code is used to solve the structural finite element equations for each substructure in parallel. NASTRAN/COSMIC is utilized as a front end for this code. Its full library of elements can be used to create an accurate and realistic aircraft mode. It is used to create the stiffness matrices for each sub-structure. The new parallel code then uses an iterative preconditioned conjugate gradient method to solve the global structural equations for the sub-structure boundary nodes. Results are presented for a wing-body configuration.

Eldred, Lloyd B.↗

A Benchmark Example for Delamination Propagation Predictions Based on the Single Leg Bending Specimen Under Quasi-Static and Fatigue Loading

Benchmark examples based on Single Leg Bending (SLB) specimens with equal and unequal bending arm thicknesses were used to assess the performance of delamination prediction capabilities in finite element codes. First, the development of the quasi-static benchmark cases using the Virtual Crack Closure Technique (VCCT) is discussed in detail. Second, based on the quasi-static benchmark results, additional benchmark cases to assess delamination propagation under fatigue loading are created. Third, the application is demonstrated for the commercial finite element code Abaqus Standard 2018. The benchmark cases are compared to results obtained from VCCT-based, automated quasi-static propagation analysis. A comparison with results from automated fatigue propagation analysis was not performed at this point since the current version of Abaqus does not include this capability under variable mixed-mode conditions. In general, good agreement between the results obtained from the quasi-static propagation analysis and the benchmark results were achieved. Overall, the benchmarking procedure proved valuable for analysis verification.

Krueger, Ronald↗

A Benchmark Example for Delamination Propagation Predictions Based on the Single Leg Bending Specimen under Quasi-static and Fatigue Loading

Benchmark examples based on Single Leg Bending (SLB) specimens with equal and unequal bending arm thicknesses were used to assess the performance of delamination prediction capabilities in finite element codes. First, the development of the quasi-static benchmark cases using the Virtual Crack Closure Technique (VCCT) is discussed in detail. Second, based on the quasi-static benchmark results, additional benchmark cases to assess delamination propagation under fatigue loading are created. Third, the application is demonstrated for the commercial finite element code Abaqus Standard 2018. The benchmark cases are compared to results obtained from VCCT-based, automated quasi-static propagation analysis. A comparison with results from automated fatigue propagation analysis was not performed at this point since the current version of Abaqus does not include this capability under variable mixed-mode conditions. In general, good agreement between the results obtained from the quasi-static propagation analysis and the benchmark results were achieved. Overall, the benchmarking procedure proved valuable for analysis verification.

Ronald Krueger↗

Semi-analytical static nonlinear structural sensitivity analysis

The paper discusses two uses of the semianalytical methods for nonlinear sensitivity analysis. First, the application to noncritical response is analyzed. It is shown that the semianalytical method is equivalent to a particular form of the overall finite difference approach. It is concluded that the difference between overall finite differences and the semianalytical approach is blurred for the case of nonlinear static response. Next, the application of the semianalytical method to calculating sensitivities of limit loads is discussed. A formulation that is easy to implement in general purpose finite element programs is derived. Three examples are used to demonstrate the application of the formulation and to explore its accuracy.

Haftka, Raphael T.↗