Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STIRRING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Microstructure and anisotropic mechanical behavior of friction stir welded AA2024 alloy sheets

The anisotropic mechanical properties of friction stir welded (FSW) AA2024-T3 alloy joints were investigated based on the uniaxial tensile tests. The joint microstructure was examined by using electron back-scattered diffraction and transmission electron microscope. Results show that the evident anisotropic failure and yielding are present in the FSW joints. With the increase of loading angle from 0° to 90° the ultimate tensile strength and elongation of the specimens consistently decrease, or at first decrease and then increase, depending on the FSW process parameters. The specimen cut from the weld direction, i.e. a loading angle of 0°, exhibits the highest strength and elongation. - Highlights: • Microstructure and anisotropy of friction stir welded joints were studied. • The evident anisotropic failure and yielding are present in joints. • The lowest yield stress and UTS are at 45° and 60° loadings, respectively. • Rotation speed heavily impact on the anisotropy of joints.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Friction stir processing of an aluminum-magnesium alloy with pre-placing elemental titanium powder: In-situ formation of an Al{sub 3}Ti-reinforced nanocomposite and materials characterization

A fine-grained Al–Mg/Al{sub 3}Ti nanocomposite was fabricated by friction stir processing (FSP) of an aluminum-magnesium (AA5052) alloy with pre-placed titanium powder in the stirred zone. Microstructural evolutions and formation of intermetallic phases were analyzed by optical and electron microscopic techniques across the thickness section of the processed sheets. The microstructure of the nanocomposite consisted of a fine-grained aluminum matrix (1.5 µm), un-reacted titanium particles (<40 µm) and reinforcement particles of Al{sub 3}Ti (<100 nm) and Mg{sub 2}Si (<100 nm). Detailed microstructural analysis indicated solid-state interfacial reactions between the aluminum matrix and micro-sized titanium particles to form Al{sub 3}Ti intermetallic phase. The hard inclusions were then fractured and re-distributed in the metal matrix by the severe thermo-mechanical conditions imposed by FSP. Evaluation of mechanical properties by hardness measurement and uniaxial tensile test determined significant enhancement in the mechanical strength (by 2.5 order of magnetite) with a high ductility (~22%). Based on a dislocation-based model analysis, it was suggested that the strength enhancement was governed by grain refinement and the presence of hard inclusions (4 vol%) in the metal matrix. Fractographic studies also showed a ductile-brittle fracture mode for the nanocomposite compared with fully ductile rupture of the annealed alloy as well as the FSPed specimen without pre-placing titanium particles. - Highlights: • FSP was employed to fabricate in situ nanocomposite. • The AA5052 Al alloy with pre-placed micro-sized Ti particles were utilized. • The structural analysis was revealed that the in situ formation of Al{sub 3}Ti nanophase. • The SZ grain structure was refined by PSN and ZHP mechanisms during DRX. • Hardness and tensile strength were improved up to ~2.5 times with a good ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Microstructure, texture, and mechanical properties of friction stir welded commercial brass alloy

Microstructural evolution during friction stir welding of single-phase brass and corresponding mechanical properties were investigated. For this purpose, 2 mm thick brass plate was friction stir welded at a rotational speed of 450 rpm and traverse speed of 100 mm/min. The microstructure of the joint was studied using optical microscopy, scanning electron microscopy equipped with electron back scattered diffraction system, and scanning transmission electron microscopy. The mechanical properties were measured using hardness and tensile tests. The formation of subgrains and their transformation into new grains in conjunction with existence of A{sub 1}{sup ⁎}, A{sub 2}{sup ⁎} and C texture components revealed that the continuous dynamic recrystallization plays a dominant role in the microstructural evolution. However, grain boundary bulging, along with the formation of twin boundaries, and presence of the G texture component showed that the discontinues dynamic recrystallization may participate in the new grain formation. Furthermore, the different strengthening mechanisms, which caused the higher strength of the joint, were discussed. - Highlights: •Microstructural evolution during FSW of a single phase brass was investigated. •CDRX and DDRX were the main mechanisms of the grain structure formation during FSW. •GDRX and SRX were not contributed in grain structure formation. •The lamellas TBs were formed in the SZ of the joints. •Grain boundary, dislocation, and texture effects resulted in higher strength.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Microstructure, mechanical properties and microtexture of friction stir welded S690QL high yield steel

Two try-out campaigns of friction stir welding (FSW) were performed with different friction parameters to join S690QL high yield strength steel. The welds were investigated at macroscopic and microscopic scales using optical and electronic microscopy and microhardness mapping. Welds of the second campaign exhibit microstructures and mechanical properties in accordance with requirements for service use. Microtexture measurements were carried out in different zones of welds by electron backscattered diffraction (EBSD). It is shown that that texture of the bottom of the weld is similar to that of the base metal, suggesting a diffusion bonding mechanism. Finally, the mechanical properties (tensile strength, resilience, bending) were established on the most promising welds. It is shown that it is possible to weld this high yield strength steel using FSW process with satisfactory geometric, microstructural and mechanical properties. - Highlights: •1000 mm ∗ 400 mm ∗ 8 mm S690QL steel plates are joined by friction stir welding (FSW). •Maximum hardness is reduced by optimization of process parameters. •Various microstructures are formed but no martensite after process optimization. •Texture is modified in mechanically affected zones of the weld. •Texture in the bottom of the weld is preserved, suggesting diffusion bonding.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization and pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Microstructural variation through weld thickness and mechanical properties of peened friction stir welded 6061 aluminum alloy joints

The current study examined the effect of microstructure variation on the development of mechanical properties in friction stir welded joints of 6061-T6 aluminum alloy, which were subsequently processed by shot peening (SP). Following to FSW, fatigue specimens were extracted perpendicularly to the welding direction. Surface Skimming to 0.5 mm from crown and root sides of the joint was made and SP was later applied on the two sides using ceramic shots of two different Almen intensities of 0.18 mmA and 0.24 mmA. Microstructural examination by electron back scattered diffraction (EBSD) indicated variation in the grain refinement of the weld zone, with coarsest grains (5 μm) at the crown side and finest grains (2 μm) at the root side. Reduction of microhardness to 60 HV occurred in the weld zone for samples in FSW condition. Application of SP promoted significant strain hardening at the crown side, with Almen intensities of 0.24 mmA providing maximum increase in microhardness to 120 HV. On the contrary, only a maximum microhardness of 75 HV was obtained at the root side. The difference in strain hardening capability at the two sides was strongly dependent on grain size. The two Almen intensities produced similar distribution of compressive residual stresses in the subsurface regions that led to enhance the fatigue strength to the level of base metal for N ≥ 10{sup 5} cycles. Yet, the increase in fatigue strength was more pronounced with increasing Almen intensity to 0.24 mmA, demonstrating further enhancement by strain hardening. - Highlights: • Grain refinement was observed after friction stir welding of AA 6061-T6. • Reduction in microhardness and fatigue strength were obtained after welding. • Variation in grain refinement led to different hardening behavior after peening. • Shot peening induced beneficial compressive residual stresses. • Shot peening and surface skimming markedly improved the fatigue performance.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Fabrication of Al-Zn solid solution via friction stir processing

Highlights: • Thermomechanical nature of FSP was utilized for mechanical alloying. • Zn particles dissolved in Al during FSP to form solid solution. • Second pass of FSP lead to homogenization and partial decomposition of the solid solution. • Processed alloy exhibited improved hardness over base and FSPed metal. • The process can be adopted for site specific property enhancement. - Abstract: The present study demonstrates that friction stir processing (FSP) can be used as a mechanical alloying tool to process solid solution. Zn was incorporated in commercially pure aluminium by multi-pass FSP leading to its dissolution and formation of supersaturated solid solution which was confirmed by X-ray diffraction and scanning electron microscopy. The hardness across the stir zone matched with the distribution of Zn and was significantly improved compared to the base metal. The supersaturated solid solution that formed in the first pass, partially decomposed during the second pass, leading to the formation of fine Al-Zn precipitates. Thermal stability of the microstructure against abnormal grain growth was also improved after the second pass due to the pinning effect of the grain boundary precipitates. FSP also caused grain refinement of the alloy yielding fine equiaxed grains in the range of 4–6 μm with a high fraction (> 67%) of high angle grain boundaries. Such microstructure is conducive for isotropic properties and the fact that the microstructure is stable against thermal cycles make the process suitable for selective alloying for location specific property enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Evaluation of the microstructure and mechanical properties of WC particle reinforced aluminum matrix composites fabricated by friction stir processing

Highlights: • FSP was used for the preparation of aluminum matrix composites reinforced with WC particle. • WC particles were uniformly distributed in the composite. • WC particles refined the grains of aluminum matrix. • WC particles enhanced the hardness and tensile strength, but decreased the ductility. - Abstract: Tungsten carbide (WC) is an attractive reinforcing material for aluminum and its alloys. However, it is technically challenging to fabricate WC particle reinforced aluminum matrix composites (AMCs) with homogeneous distribution of WC particles by liquid state processing techniques because of large density gradient. The present work aim to produce WC particle reinforced aluminum matrix composites (AMCs) through friction stir processing (FSP) and analyze the effect of its volume fraction on the microstructural features and the mechanical behavior of the developed AMCs. Microstructural evaluation was conducted on the cross-sections of the samples by optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD). Microhardness testing was conducted across the cross-sections of FSPed samples to obtain hardness profiles and tensile test was conducted on as-received Al and FSPed samples. The fabricated AMCs exhibited the homogeneous distribution of WC particle with no obvious particle clustering in the stir zone, irrespective of position and WC particle volume fraction. Excellent WC/Al interfacial bonding was obtained in all FSPed AMCs with obviously refined grains. The average size of WC particles after FSP was slightly reduced with the increased volume fraction. It was also found that increasing the volume fraction of WC particles favored the grain refinement, improved the hardness and strength, but decreased the ductility. This improvement in the hardness and strength was attributed to the grain refinement strengthening and homogeneous distribution of WC particles. The decreased ductility resulted from the introduction of more WC particles. Increasing the volume fraction of WC particles caused the nature of fracture to move towards brittle nature.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Influencing mechanism of Al-containing Zn coating on interfacial microstructure and mechanical properties of friction stir spot welded Mg–steel joint

Highlights: • Al-containing Zn coating improved Mg–steel interfacial wettability during friction stir spot welding (FSSW). • Pre-existing Al{sub 5}Fe{sub 2} phase in coating on steel surface promoted Mg–steel metallurgical bonding. • A high tensile-shear load of 4.3 kN was obtained in FSSW AZ31–steel joint. - Abstract: 2.4 mm thick AZ31 Mg alloy sheet and 1.5 mm Q234 steel sheet with a hot-dipped Al-containing Zn coating were friction stir spot welded (FSSW) using a pinless tool. It was shown that the Al-containing Zn coating played a crucial role in joining the Mg alloy and steel during FSSW. The Zn coating observably improved the Mg–steel interfacial wettability during FSSW, and the Al{sub 5}Fe{sub 2} phase in the Zn coating on the steel substrate surface promoted the metallurgical bonding of Mg alloy and steel. It was confirmed that the Al{sub 5}Fe{sub 2} phase on the steel surface resulted from the reaction between the steel substrate and the Al in the Zn coating during hot-dipping, and was not related to the Al-containing Mg alloy substrate. The tensile-shear load of the FSSW Mg–steel joint reached 4.3 kN. The fracture of the joint occurred along the interface on the steel substrate side. The interface between the Al{sub 5}Fe{sub 2} layer and Mg alloy substrate was the weakest region of the Mg–steel joint.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Effect of cooling conditions on microstructure and mechanical properties of friction stir welded 7055 aluminium alloy joints

Highlights: • Water cooling improves tensile properties of friction stir welded 7055 Al alloy. • Water cooling results in smaller grains and second phase in nugget zone. • Water cooling results in finer second phase in thermos-mechanically affected zone. • Water cooling results in finer second phase in heat affected zone. • Fracture surface is flat for air-cooled joint but zig-zag for water-cooled one. - Abstract: The microstructure and mechanical properties of friction stir welded 7055 aluminium alloy under air cooling and water cooling were investigated by means of hardness and tensile testing, optical microscopy and transmission electron microscopy. Water cooling results in reduced softening in the weld zone and therefore higher tensile strength compared to air cooling. Fracture generally occurs within the thermo-mechanically affected zone (TMAZ) and heat affected zone (HAZ) on the retreating side in joints welded under air cooling but shifts towards the TMAZ and nugget zone (NZ) in the joints welded under water cooling. The fracture surfaces are generally flat for the air-cooled joint, but exhibits a zig-zag feature for the water-cooled joint. The mechanical behaviour of the weld has been discussed in light of the change in grain structure and precipitation in the NZ, TMAZ and HAZ caused by cooling conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Interfacial bonding mechanism and mechanical properties of micro friction stir blind riveting for multiple Cu/Al ultra-thin layers

Highlights: • Micro Friction Stir Blind Riveting is developed for joining multilayer ultra-thin dissimilar materials. • Interfacial bonding mechanism for different interfaces is identified. • Proposed technique offers better mechanical performance than conventional micro riveting process. • The relationship between each interfacial bonding mechanism and improved mechanical property is elucidated. - Abstract: In this research, bonding mechanisms and mechanical properties were investigated for a newly developed multilayer dissimilar material joining technique, micro friction stir blind riveting (viz. μFSBR), where the multilayer micro joint was made consisting of one Cu layer and three Al layers (each layer having 0.203 mm thickness) connected through Al rivet. Different microscopy techniques were employed (i.e. scanning electron microscopy and transmission electron microscopy) to unearth the bonding mechanisms of the three interfaces (i.e. Al rivet and Cu sheet interface, Cu sheet and Al sheet interface, and Al rivet and Al sheet interface) which revealed intricate yet distinct bonding phenomenon for each interface. A nano-scale diffusion layer in addition to two-way material flow consequential heterogeneous lamellar structures and mechanical interlocking was formed at the Al rivet and Cu sheet interface; Cu particles diffused into a non-uniform thickness thin oxide layer at the Cu sheet and Al sheet interface; and Al sheet experienced grain refinement near the interface close to Al rivet with a nano-scale gap. These observations revealed that both mechanical and metallurgical bonding occurred simultaneously in μFSBR. The formation of different bonding mechanisms resulted in superior bonding strength and absorbed energy compared to conventional micro blind riveting joints, which was further confirmed through layer by layer tensile tests.

36 MATERIALS SCIENCE↗
DOE OSTI2018

On visualizing material flow and precipitate evolution during probeless friction stir spot welding of an Al-Li alloy

Highlights: • Severe thermal cycle and deformation refined grains and intermetallic particles in SZ. • T{sub 1} phases fully dissolved in SZ followed by re-precipitation of GP zone and δ′ phases. • The predominant flow direction remained in spiral-like pattern during P-FSSW. • Local abrasion existed in the lap-weld interface due to flow difference, forming joining. - Abstract: The precipitate evolution and material flow visualization during probeless friction stir spot welding (P-FSSW) of an Al-Li alloy has been investigated experimentally and numerically in this work. Due to severe heat input during welding, the main strengthening phases of T{sub 1} fully dissolved in the stir zone followed by the re-precipitation of GP zone and δ′ phases, assisted with the refinement of the intermetallic particles and grains. The history of material flow was three-dimensionally visualized with a tracer, studied with X-ray tomography. The experiments and the simulation results provided a consistent interpretation of a circumferential material flow which moved inwards radially near the top surface. Upward flow in the bottom sheet improved with dwell time, causing the interface to bend. Local abrasion between the two sheets due to flow difference led to the disruption of oxide layer, and formed a connection at the interface.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A comparative research on bobbin tool and conventional friction stir welding of Al-Mg-Si alloy plates

Highlights: • 6061-T4 Al plates were successfully welded by both BT-FSW and C-FSW processes. • A wide welding parameter window was achieved with bobbin tool. • BT-FSW joints showed good strength similar to that of C-FSW joints. • Proving that an Isothermal Dissolution Layer Theory also apply to BT-FSW - Abstract: In our work, Al-Mg-Si (6061Al -T4) plates of 6 mm thickness were subjected to bobbin tool friction stir welding (BT-FSW) and conventional friction stir welding (C-FSW) for comparison. How the welding process affects the microstructure and mechanical properties was investigated at various rotation rates and welding speeds. The results showed that butt FSW joints with high quality could be produced at the selected parameters. The joint strength rose with enhanced welding speed and was nearly independent of the rotation rate in both the welding processes. The strength of the joints produced with BT-FSW reached the same level as that of the C-FSW. The maximum joint strength of 229 MPa was 93% of the base material (BM), which is superior to the reported results of 60–80% for the T4 condition. The fracture position of most of the joints was in the heat-affected zone (HAZ), which is the lowest hardness zone.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Texture and precipitation behavior of friction stir welded Inconel 825 alloy

The microstructure, texture pattern, and precipitation behavior of friction stir butt welded Inconel 825 alloy are highlighted here. The microstructure of bright regions and black-banded regions in the stir zone (SZ) is characterized by SEM, EBSD, and TEM with EDS. EBSD analysis justifies that the SZ exhibits a dynamic recrystallized structure. Grain boundary mapping corroborates the insignificant difference in the low- and high-angle grain boundaries fraction between the SZ, the thermo-mechanically affected zone, and the base metal. TEM analysis confirms the formation of nano twins and dispersion of nano-size precipitations in the grains, and at the grain boundaries as well. Grain refinement and nano-size precipitation formation in the SZ significantly enhanced both microhardness and tensile strength.

Das, Hrishikesh↗
DOE OSTI2011

The Role of Friction Stir Welding on the Microstructure and Mechanical Properties of AZ31B-H24 Mg alloy

In this study, an attempt was made to join AZ31B magnesium alloy by friction stir welding (FSW) process. A single tool with cylindrical screw threaded pin was used to investigate the effect of welding parameters on microstructure and mechanical properties of stir zone (SZ). Several welds were made at different rotational ({omega}) and traverse ({upsilon}) speeds, while the {omega}/{upsilon} ratios were kept constant. The optical and scanning electron microscopy were used to study the variation of microstructure across the welds. Moreover, micro-hardness and tensile tests were carried out to evaluate the mechanical properties of joints. It was found that {omega} plays more significant role on the resulted grain structure than {upsilon}, and at a constant {omega}/{upsilon} ratio, decreasing rotational speed decreased the size of grains, and hence, improved the hardness value and the tensile strength of the SZ.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Friction stir processing on carbon steel

Friction stir processing of medium carbon steel samples has been carried out using a milling machine and tools made of cemented tungsten carbide. Samples have been machined from 40 and 40X steels. The tools have been made in the shape of 5×5×1.5 mm and 3×3×1.5 mm tetrahedrons. The microstructure of stirred zone has been obtained using the smaller tool and consists of fine recrystallized 2-3 μm grains, whereas the larger tool has produced the 'onion-like' structures comprising hard quenched 'white' 500-600 MPa layers with 300-350 MPa interlayers of bainite needles. The mean values of wear intensity obtained after measuring the wear scar width were 0.02 mm/m and 0.001 mm/m for non-processed and processed samples, respectively.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2011

EVOLUTIONARY TRACKS OF TIDALLY STIRRED DISKY DWARF GALAXIES

Using collisionless N-body simulations, we investigate the tidal evolution of late-type, rotationally supported dwarfs inside Milky Way sized host galaxies. Our study focuses on a wide variety of dwarf orbital configurations and initial structures. During the evolution, the disky dwarfs undergo strong mass loss, the stellar disks are transformed into spheroids, and rotation is replaced by random motions of the stars. Thus, the late-type progenitors are transformed into early-type dwarfs as envisioned by the tidal stirring model for the formation of dwarf spheroidal (dSph) galaxies in the Local Group. We determine the photometric properties of the dwarfs, including the total visual magnitude, the half-light radius, and the central surface brightness as they would be measured by an observer near the galactic center. Special emphasis is also placed on studying their kinematics and shapes. We demonstrate that the measured values are biased by a number of observational effects including the increasing angle of the observation cone near the orbital pericenter, the fact that away from the pericenter the tidal tails are typically oriented along the line of sight, and the fact that for most of the evolution the stellar components of the dwarfs are triaxial ellipsoids whose major axis tumbles with respect to the line of sight. Finally, we compare the measured properties of the simulated dwarfs to those of dwarf galaxies in the Local Group. The evolutionary tracks of the dwarfs in different parameter planes and the correlations between their different properties, especially the total magnitude and the surface brightness, strongly suggest that present-day dSph galaxies may have indeed formed from late-type progenitors as proposed by the tidal stirring scenario.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

TRENDS IN DWARF EARLY-TYPE KINEMATICS WITH CLUSTER-CENTRIC RADIUS DRIVEN BY TIDAL STIRRING

We model the dynamics of dwarf early-type galaxies in the Virgo cluster when subject to a variety of environmental processes. We focus on how these processes imprint trends in the dynamical state (rotational versus pressure support as measured by the λ{sub Re/2}{sup ∗} statistic) with projected distance from the cluster center, and compare these results to observational estimates. We find a large scatter in the gradient of λ{sub Re/2}{sup ∗} with projected radius. A statistical analysis shows that models with no environmental effects produce gradients as steep as those observed in none of the 100 cluster realizations we consider, while in a model incorporating tidal stirring by the cluster potential 34% of realizations produce gradients as steep as that observed. Our results suggest that tidal stirring may be the cause of the observed radial dependence of dwarf early-type dynamics in galaxy clusters.

79 ASTRONOMY AND ASTROPHYSICS↗