Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Pilot Plant”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

60 years of science in ICF: from conception to scientific breakeven on the National Ignition Facility

The recent achievements of a burning plasma, fusion ignition, and scientific energy gain with deuterium-tritium (DT) fuel at Lawrence Livermore National Laboratory’s National Ignition Facility (NIF) represents a major milestone in the development of inertial confinement fusion (ICF) and all of fusion research. In these experiments, fuel pressures well in excess of hundreds of GBars were achieved in the compressed fuel, and robust alpha heating of the fuel, far in excess of the energy provided by the implosion, were demonstrated for the first time. These achievements occurred 60 years after the inception of ICF and the first laser demonstration, and were made possible by more than five decades of research at laser facilities around the world. Advances in laser technology both in wavelength and precision, motivated by improved understanding of laser-plasma interaction physics and the demands of targets; improvements in target fabrication inspired by the need to control and minimize hydrodynamic instabilities in the implosion; and multi-dimensional simulations and diagnostics have been critical to this achievement. This paper will summarize the scientific and technical advances, the surprises, and the challenges that had to be overcome to achieve these goals.

fusion↗
DOE OSTI2025

Techno-economic evaluation of emission control configurations for AMP/PZ-based post-combustion CO 2 capture

Minimizing the environmental impacts of amine-based post-combustion carbon capture technologies is essential for regulatory compliance and public acceptance. Experimental campaigns at RWE's CO 2 capture pilot plant in Niederaussem using CESAR1 demonstrated that combining existing emission abatement technologies can substantially reduce the concentration of amines and degradation products in the CO 2 -depleted flue gas to below the detection limit of an infrared spectrometer. The campaign confirmed that a proprietary dry bed technology (OEASE aerozone™) or a second water wash can reduce AMP and PZ emissions to below 1 mg/Nm 3 . However, an acid or chemically active wash downstream of the water wash is necessary to reduce NH 3 emissions to very low levels (<2 mg/Nm 3 ). Combining a dry bed with an acid wash significantly reduces both the required acid solution and the resulting acid waste. The techno-economic analysis indicates that implementing emission mitigation technologies provides substantial environmental benefits for the CESAR1 process, with only a marginal increase (<1 €/tCO 2 ) in both the carbon capture cost (CCC) and CO 2 avoidance cost (CAC). The additional capital cost associated with extra column packing is offset by operational cost savings from reduced solvent losses. For stringent emission permits targeting NH 3 , a configuration combining a dry bed upstream of the water wash followed by an acid wash achieves the best balance between emission control and cost efficiency. This configuration results in a Levelized Cost of Electricity (LCOE) of 143 €/MWh, a CCC of 45.4 €/tCO 2 , and a CAC of 88.4 €/tCO 2 .

AMP↗
DOE OSTI2025

Machine learning modeling and model predictive control of a closed-circuit reverse osmosis system

Closed-circuit reverse osmosis (CCRO) offers a flexible and energy-efficient alternative to conventional reverse osmosis by operating in a semi-batch mode that recycles brine, enabling higher recovery rates and reduced specific energy consumption (SEC). However, developing accurate, system-level dynamic models for CCRO remains challenging due to its nonlinear, multi-phase operation and sensitivity to variable feed water conditions. Traditional modeling approaches, such as NARMAX (nonlinear autoregressive moving average with exogenous inputs), often struggle to generalize across varying inlet feed concentrations, necessitating frequent parameter re-estimation and limiting their utility for real-time control applications. To address these limitations, we developed a long short-term memory (LSTM) neural network model trained on an extensive experimental data set from a CCRO pilot plant. The model accepts three inputs, feed flow rate, recirculation flow rate, and initial feed conductivity, and predicts three key outputs: reject conductivity, feed pump power draw, and recirculation pump power draw. We validated the LSTM model against experimental data, demonstrating its ability to distinguish between different feed conductivities and adapt to variable flow rates. Subsequently, we incorporated the LSTM model within a nonlinear model predictive control (MPC) scheme and conducted closed-loop simulations to optimize the integrated SEC (iSEC). In conclusion, the results project up to a 6% reduction in iSEC by using MPC to optimize performance over the entire experiment duration, without requiring any random excitation for data collection or parameter re-estimation.

Desalination↗
DOE OSTI2022

Environmental evaluation of radioactivity levels and associated radiation hazards in groundwater around the WIPP site

Groundwater may contain radioactive substances which can be dangerous to human health. Concentrations of natural radionuclides polonium (Po), thorium (Th), uranium (U), and radium (Ra) isotopes were measured in groundwater samples collected from different locations in the vicinity of the Waste Isolation Pilot Plant (WIPP) site in Carlsbad, New Mexico. The average values of gross activity concentrations of 210 Po, 228 Th, 238 U, 234 U, 226 Ra and 228 Ra isotopes were determined to be 1.62 Bq L -1 in shallow groundwater and 5.88 Bq L -1 in deep groundwater, respectively. The total radioactivity in deep groundwater was higher than that in shallow groundwater, and most of the radioactivity in the water is from 226 Ra. Furthermore, the effective doses for ingestion of natural radionuclides were about 0.333 mSv y–1 for shallow groundwater and about 1.338 mSv y –1 for deep groundwater samples, which are higher than the World Health Organization (WHO, 2017) guideline level (0.1 mSv y –1 ) for drinking water. Ra dominated the total ingestion dose, contributing 93.06 % and 75.40 % of the total effective doses to the deep and shallow groundwater, respectively. The ingrowth and decay of natural radionuclides suggested that 228 Ra/ 226 Ra ratio can be a useful indicator of the source of radioactive contamination. The radioactivity data obtained from the investigated groundwater samples can be used to establish a baseline for radioactivity levels in groundwater around the WIPP site.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2024

Toward a high-fidelity tritium transport modeling for retention and permeation experiments

We report Tritium Migration Analysis Program version 8 (TMAP8), the latest version of TMAP, was developed within the framework of the Multiphysics Object-Oriented Simulation Environment (MOOSE). Created at Idaho National Laboratory (INL), MOOSE is an open-source, dimension-agnostic, fully coupled, and fully implicit multiphysics platform featuring massively parallel computation capabilities. Using TMAP8, tritium transport in a divertor monoblock was analyzed to elucidate the effects of pulsed operation (up to fifty 1,600 s plasma discharge and cool-down cycles) on the tritium in-vessel inventory source term and ex-vessel release term (i.e., tritium retention and permeation) for safety analysis. With its built-in Message Passing Interface capability, TMAP8 can, in under 2 h, simulate tritium transport in three different layered materials (i.e., tungsten, copper, and copper-chromium-zirconium alloy) in 2D geometry, using a single device/computer with 10 cores. The MOOSE-based TMAP8 code can leverage other MOOSE tools developed under the Nuclear Energy Advanced Modeling and Simulation program to perform tritium and thermal transport in complex geometries and multiphysics environments. And via its massively parallel computation, MOOSE will enable the fusion pilot plant designers to conduct high-fidelity multiphysics modeling for the design of the divertor and blanket systems as well as for the safety analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Validation of NSFsim as a Grad-Shafranov equilibrium solver at DIII-D

Plasma shape is a significant factor that must be considered for any Fusion Pilot Plant (FPP) as it has significant consequences for plasma stability and core confinement. A new simulator, NSFsim, has been developed based on a historically successful code, DINA [1], offering tools to simulate both transport and plasma shape. Specifically, NSFsim is a free boundary equilibrium and transport solver and has been configured to match the properties of the DIII-D tokamak. This paper is focused on validating the Grad-Shafranov (GS) solver of NSFsim by analyzing its ability to recreate the plasma shape, the poloidal flux distribution, and the measurements of the simulated diagnostic signals originating from flux loops and magnetic probes in DIII-D. Five different plasma shapes are simulated to show the robustness of NSFsim to different plasma conditions; these shapes are Lower Single Null (LSN), Upper Single Null (USN), Double Null (DN), Inner Wall Limited (IWL), and Negative Triangularity (NT). The NSFsim results are compared against real measured signals, magnetic profile fits from EFIT [2], and another plasma equilibrium simulator, GSevolve [3]. EFIT reconstructions of shots are readily available at DIII-D, but GSevolve was manually ran by us to provide simulation data to compare against.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Preliminary proof-of-concept of real-time divertor heat flux control from infrared cameras with nitrogen injection in the DIII-D tokamak

In future tokamak reactors like ITER and the Fusion Pilot Plant (FPP), real-time feedback control of heat flux to the plasma-facing components (PFC) will be critical for steady-state operation. This work presents the first experimental demonstration of real-time divertor heat flux estimation with infrared thermography and feedback control with impurity seeding on the DIII-D tokamak. The flexible infrastructure of the Plasma Control System (PCS) on DIII-D makes this new capability possible. The PCS software runs on a gateway computer system, and five real-time compute nodes. An array of low latency streaming digitizers from D-TACQ Solutions connects to these real-time computers to collect and process data, and send commands to actuators during plasma discharges. This system handles the signal IO from the tokamak and allows the PCS to utilize the diagnostic data necessary to perform control in real-time. Feedback control on heat flux was accomplished by feeding infrared camera data from the “Infrared TV” (IRTV) camera to a custom-developed User Datagram Protocol (UDP) server. This server transmits infrared data to a newly developed PCS algorithm that estimates the heat flux to PFC. Here, a proportional integral derivative (PID) controller minimizes the error between a heat flux reference and the real-time estimate by injecting nitrogen gas into the divertor.

Algorithm development↗
DOE OSTI2024

Synthesis of results for Brine Availability Test in Salt (BATS) DECOVALEX-2023 Task E

In the 2023 phase of the international collaborative DECOVALEX modeling project, Task E focused on understanding thermal, hydrological, and mechanical (THM) processes related to predicting brine migration in the excavation damaged zone around a heated excavation in salt. Salt is attractive as a disposal medium for radioactive waste because it is self-healing and is essentially impermeable and non-porous in the far field. Investigation of the short-term, near-field behavior is important for radioactive waste disposal because this early period strongly controls the amount of inflowing brine. Brine leads to corrosion of waste forms and waste packages, and possible dissolution of radionuclides with brine transport being a potential transport vector to the accessible environment.The Task was divided into steps. Step 0 included matching unheated brine inflow data from boreholes at the Waste Isolation Pilot Plant (WIPP) and matching temperature observations during a Brine Availability Test in Salt (BATS) heater test. Step 1 included validation of models against a thermo-poroelastic analytical solution, and two-phase flow around an excavation. Finally, Step 2 required all the individual components covered in steps 0 and 1 to come together to match observed brine inflow behavior during the same BATS heater test.There were a range of approaches from the teams, from mechanistic to prescriptive. Given the uncertainties in the problem, some teams used one- or two-dimensional models of the processes, while other teams included more geometrical complexity in three-dimensional models. Task E was a learning experience for the teams involved, and feedback from the modeling teams has led to changes in follow-on BATS experiments at WIPP. The primary Task E lessons learned were the impact of hydrologic initialization methods (wetting up vs. drying down), the difference between confined and unconfined thermal expansion, and the large changes in permeability associated with heating and cooling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Numerical simulation of compressible fluid-dynamics in the chamber of inertial fusion energy systems

Here, this paper aims to establish new and innovative modeling capabilities for analyzing chambers in Inertial Fusion Energy (IFE) systems. IFE is emerging as a promising method to achieve fusion power production, but several challenges must be overcome to develop an IFE pilot plant or deploy commercial IFE systems. These challenges are both theoretical and technical, encompassing a deeper understanding of the underlying physical phenomena and the development of new technologies and materials. One of the needs is to develop mathematical models to describe IFE systems and numerical tools to simulate them. This paper contributes to this endeavor by presenting a new OpenFOAM solver for IFE systems, focusing on gas dynamics in their chambers. The analysis and development of chamber designs will play a significant role in the transition from single-shot experiments to high-repetition rates, as there is a need to protect the chamber walls from the intense radiation fields produced by fusion reactions. A promising design option, normally referred to as thick wall chamber design, consists in using lithium or molten salt jet arrays within the chamber. A critical phenomenon is the venting of high-pressure gases from the center to the external part of the chamber, passing through the blanket array. This process involves the propagation and attenuation of strong pressure waves, requiring suitable modeling approaches for compressible fluid-dynamics. The solver proposed in this work implements a multi-material hydrodynamics model tailored to accurately describe the non-linear propagation of pressure waves while avoiding numerical oscillation issues typical of high-velocity compressible simulation. This solver is verified against numerical test cases, validated against experimental data, and applied to the analysis of the High-Yield Lithium-Injection Fusion-Energy (HYLIFE-I) concept. The relevance of this paper is threefold. Firstly, it contributes to developing and testing modeling approaches for compressible fluid-dynamics phenomena, with specific focus on the new and unexplored topic of IFE thick-liquid-wall blanket modeling. Secondly, it marks one of the first applications of the OpenFOAM library in the research field of IFE systems. Finally, the investigated problem is of practical interest for IFE developers, as it provides useful indications about relevant phenomena in pressure wave propagation in the chamber of these systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Estimation of process steady state with autoregressive models and Bayesian inference

To improve efficiency, separations engineers will typically design process circuits containing recirculating streams, which mix one or more of the process outputs with the feed material. Doing so can improve efficiency, but will cause a delay in the system reaching steady state conditions until the recirculating load mass flows stabilize. In testing separation circuits, engineers will often test a variety of factors and complete an analysis from sample results. Knowledge of if a process is at steady state, as well as the steady state conditions of a process, is essential for a valid techno-economic analysis. However, the definition of process steady state is often poorly defined, or does not include uncertainty quantification. If the performance of a process operating under two different sets of conditions are compared, an engineer who does not test for steady state or quantify steady state conditions risks producing a faulty analysis. In this work, a Bayesian statistical method for testing if all streams are at steady state is further motivated and then derived. Then after testing for steady state, the same model is used with a prior distribution that enforces a steady state assumption to estimate steady state conditions. Further, these methods were validated in a solvent extraction pilot plant where steady state conditions for all outflows were inferred with uncertainty quantification. Analysis is completed with functions available to the reader as part of the BayesMassBal (V 1.1.0) software package written in R.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Optimization of the JUNO liquid scintillator composition using a Daya Bay antineutrino detector

To maximize the light yield of the liquid scintillator (LS) for the Jiangmen Underground Neutrino Observatory (JUNO), a 20 t LS sample was produced in a pilot plant at Daya Bay. The optical properties of the new LS in various compositions were studied by replacing the gadolinium-loaded LS in one antineutrino detector. The concentrations of the fluor, PPO, and the wavelength shifter, bis-MSB, were increased in 12 steps from 0.5 g/L and 0.01 mg/L to 4 g/L and 13 mg/L, respectively. The numbers of total detected photoelectrons suggest that, with the optically purified solvent, the bis-MSB concentration does not need to be more than 4 mg/L. In order to bridge the one order of magnitude in the detector size difference between Daya Bay and JUNO, the Daya Bay data were used to tune the parameters of a newly developed optical model. Then, the model and tuned parameters were used in the JUNO simulation. Overall, this enabled to determine the optimal composition for the JUNO LS: purified solvent LAB with 2.5 g/L PPO, and 1 to 4 mg/L bis-MSB.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

ToF-SIMS spectral analysis of pristine and neutron irradiated single crystal tungsten

Time-of-flight secondary ion mass spectrometry (ToF-SIMS) has many promising features in studying materials including high spatial resolution and high mass accuracy of elements, molecules, and isotopes. Its ability to resolve isotopes is especially attractive in studying transmutation products of single crystal tungsten (SCW) post neutron irradiation. Tungsten (W) is a contender of plasma facing materials (PFMs) due to its high thermal and radiological stability. PFMs to be used in the construction of fusion vessels are subject to high temperature and neutron irradiation, resulting in changes to materials including transmutation, which ultimately impact material mechanical and thermal properties. We used IONTOF TOF.SIMS V instrument equipped with a 30 keV Bi 3 + primary ion beam to study pristine SCW and irradiated SCW speciemens. Scanning electron microscope coupled with focused ion beam (SEM-FIB) was used to reduce the dosage of neutron irradiated tungsten and prepare for specimens for SIMS analysis. Static ToF-SIMS spectra were obtained, and transmutation product peak identification was presented in this work. Identified molecules and molecular fragments were compared against isotope theoretical mass to charge ratios of tungsten, rhenium, osmium, and other relevant products. Our results show that ToF-SIMS provides a viable means to study transmutation products of W post neutron irradiation. Such applications are suitable to investigate transmutation effects on materials that are being considered and developed for fusion pilot plants.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Divertor heat flux challenge and mitigation in SPARC

Owing to its high magnetic field, high power, and compact size, the SPARC experiment will operate with divertor conditions at or above those expected in reactor-class tokamaks. Power exhaust at this scale remains one of the key challenges for practical fusion energy. Based on empirical scalings, the peak unmitigated divertor parallel heat flux is projected to be greater than 10 GW m -2 . This is nearly an order of magnitude higher than has been demonstrated to date. Furthermore, the divertor parallel Edge-Localized Mode (ELM) energy fluence projections (~11–34 MJ m -2 ) are comparable with those for ITER. However, the relatively short pulse length (~25 s pulse, with a ~10 s flat top) provides the opportunity to consider mitigation schemes unsuited to long-pulse devices including ITER and reactors. The baseline scenario for SPARC employs a ~1 Hz strike point sweep to spread the heat flux over a large divertor target surface area to keep tile surface temperatures within tolerable levels without the use of active divertor cooling systems. In addition, SPARC operation presents a unique opportunity to study divertor heat exhaust mitigation at reactor-level plasma densities and power fluxes. Not only will SPARC test the limits of current experimental scalings and serve for benchmarking theoretical models in reactor regimes, it is also being designed to enable the assessment of long-legged and X-point target advanced divertor magnetic configurations. Experimental results from SPARC will be crucial to reducing risk for a fusion pilot plant divertor design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Improved CO 2 Capture Performance of Electrochemically Mediated Amine Regeneration Processes with Ionic Surfactant Additives

For the effective reduction of global CO 2 emissions, it is essential to develop and deploy efficient and cost-effective technologies for CO 2 capture, especially from large point sources. We recently developed an electrochemically mediated amine regeneration (EMAR) system to replace traditional thermal desorption for the capture of CO 2 from post-combustion flue gases. Despite EMAR effectiveness on a laboratory scale, concerns regarding the high gas-to-liquid ratio in the electrochemical cell and long-term instability of the electrodes need to be addressed before further scale-up of the process to a pilot plant and beyond can be entertained. Accordingly, we investigated the effect of using sodium dodecyl sulfate (SDS) as an anionic surfactant and dodecyltrimethylammonium bromide (DTAB) as a cationic surfactant on the process operation. It was found that it is advantageous to use an anionic surfactant for a system such as EMAR that contains hydrophilic electrodes and a positively charged electrochemically active species. The overall cell resistance was notably reduced when SDS anionic surfactant was used. The precipitation of copper particles observed in the anode outlet when no surfactant was used was effectively avoided when SDS was added to the electrolyte, resulting in electrode stability. In addition, smaller gas bubbles were produced in the presence of the SDS surfactant, which resulted in less blockage of the electrode by the gas with a resultant lower cell potential under constant current conditions, driving more efficient CO 2 desorption. This led to an ~25% reduction in the electrochemical energy requirement, the lowest ever achieved experimentally for the EMAR process. Altogether, the addition of a very low concentration of SDS resulted in the successful circumvention of the important problems faced by the EMAR system regarding further scale-up.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Joint Geophysical and Numerical Insights of the Coupled Thermal‐Hydro‐Mechanical Processes During Heating in Salt

Abstract Salt offers an optimal medium for the permanent isolation of heat‐producing radioactive waste due to its impermeability, high thermal conductivity, and ability to close fractures through creep. A thorough understanding of the thermal‐hydrological‐mechanical (THM) processes, encompassing brine migration, is fundamental for secure radioactive waste disposal within salt formations. At the Waste Isolation Pilot Plant (WIPP), we conducted joint in situ geophysical monitoring experiments during active heating to investigate brine migration near excavations. This experiment incorporated electrical resistivity tomography (ERT) alongside high‐resolution fiber‐optic‐based distributed temperature sensing within a controlled heating experiment. Additionally, discrete element model (DEM) based numerical simulations were conducted to simulate THM processes during heating, providing a more mechanistic understanding of the coupled processes leading to the observed changes in geophysical measurements. During heating, resistivity shifts near the heater were reasonably explained by temperature effects. However, in more distant, cooler regions, the resistivity decrease exceeded predictions based solely on temperature. DEM simulations highlighted brine migration, propelled by pore pressure gradients, as the likely primary factor contributing to the additional resistivity decline beyond temperature effects. The comparison between the predicted ERT responses and observations was much improved when considering the effects of brine migration based on the DEM simulations. These geophysical and simulation findings shed light on brine migration in response to salt heating, enhancing our understanding of the coupled THM processes in salt for safe radioactive waste disposal.

58 GEOSCIENCES↗
DOE OSTI2023

Time dependent model for non-inductive ECH X-I current ramp-up for SHPD tokamak facility

Non-inductive (NI) plasma current start-up and ramp-up is an important research topic for spherical tokamak (ST) based reactors and fusion pilot plant (FPP). For a compact FPP, the OH flux availability is highly restricted due to its compact geometry. Efficient fundamental extraordinary mode (X-I) electron cyclotron heating (ECH) current start-up and ramp-up regime was identified for a reactor-like high toroidal magnetic field range which has more than a hundred times higher current drive efficiency compared to more conventional ECH methods for the relevant start-up temperature range. High current drive efficiency is possible due to the strong X-I fundamental ECH interaction only with unidirectional passing electrons constrained by the wave accessibility conditions. Here, we extend the X-I electron cyclotron current drive (ECCD) investigation to a time dependent model to simulate the non-inductive current ramp-up to 10 MA for the Sustained High-Power Density (SHPD) facility. As the X-I ECCD driven current I EC rises, due to the back EMF driven negative current, the net plasma current Ip rises more slowly with the current resistive time scale. For tokamak confinement time (both L-mode and H-Mode) which tends to rise with I p , a positive feedback results and even with constant applied ECH power, T e0 , I EC , and I p can continue to rise to very high values. However, in a realistic situation, the T e0 rise should saturate due to a number of factors such as enhanced core radiation and increased power loss at high temperature. To simulate this effect, we adopt a maximum T e0 model which would limit the temperature rise to certain T e0 . With this model, we investigated the current ramp-up for various ECH power levels and the maximum T e0 of 15, 20, and 25 keV. We find that while the power required is reduced with increasing T e0 limit due to increased current drive efficiency, the time to reach 10 MA tends to go up due to the reduced plasma resistivity for the higher T e0 limit. We also find for a given Te0 limit, the time to reach 10 MA tends to be reduced by increasing the applied ECH power by over driving the current ramp-up where I EC is driven at significantly higher level than 10 MA. While the current ramp-up time may not be an issue for the steady-state reactor systems, if it is desirable to minimize the current ramp-up time, it is prudent to have a sufficient ECH power for current over-drive and have some T e0 limiting tools such as impurity seeding for enhanced radiation. In conclusion, a well-controlled NI ECH start-up also has a potential of improving the tokamak start-up reliability and avoid run-away electrons while the NI off-axis current drive could enhance MHD stability and plasma performance improvements.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

DIII-D's role as a national user facility in enabling the commercialization of fusion energy

The path to fusion in the United States requires partnership between public and private sector. While the private sector provides the vigor to take some of the major steps necessary, there is a depth of expertise and capability in the public sector that is vital to resolving feasible approaches. As an open national user facility, DIII-D provides a crucial testbed to develop the required new technologies and approaches in relevant conditions. It has unparalleled potential to meet this challenge, thanks to its extreme flexibility and world leading diagnostics. This provides a basis to rapidly develop solutions that project to future reactors with confidence. The program has thus been redeveloped to enable public and private sector engagement and testing of new concepts. A new technology program has been launched to resolve plasma interacting technologies. With modest heating upgrades, the facility can confront the crucial “Integrated Tokamak Exhaust and Performance” gap, to resolve core, exhaust and technology solutions together. The device is also being redeveloped as a training facility, with dedicated student run time, a mentorship program, and open access to all opportunity roles, part of wider efforts to diversify and open pathways through inclusion, access, and equity. This exciting agenda is enabling scientists and technology researchers to pioneer the solutions needed for a Fusion Pilot Plant (FPP) and ITER this decade. As a national user facility, DIII D has singular potential to provide the tools, teams, and insight necessary, to do its part in moving the United States rapidly toward the commercialization of fusion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Core-edge integrated predictive studies of ST40 and NSTX plasmas with the scrape-off layer box model

The ability to model the interplay between the core and edge of tokamak plasmas is crucial to designing both the plasma operating scenario of a fusion pilot plant and the design of the tokamak itself. Scrape-off-layer (SOL) models that are tailored to integrated scenario modeling need to have fast turn-around time and minimal computational burden to enable wide parameter-space coverage for design scoping. The SOL 0-D Box model is a reduced SOL model based on global power and particle balance that captures the essential physics of SOL transport with little computational cost. The usage of the 0-D Box model in core-edge coupled simulations has been demonstrated in both interpretive and predictive modes on a variety of devices. This paper presents a sensitivity study of the 0-D Box model to the input SOL heat-flux width for an ST40 plasma. This study demonstrates that accurate prediction of this width is crucial to predicting global performance parameters of a plasma scenario, such as energy confinement time and flux consumption. We also present an extension of the Box model to 1-D to allow for parallel variation of plasma parameters along the magnetic field lines. The 1-D Box model is then compared with SOLPS-ITER simulations of an NSTX plasma. Advantages and limitations of the Box model are discussed, and future directions are outlined.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗