Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PURE STATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2018

Development of an 400 L Integrated Refrigeration and Storage Cryostat for LNG/LCH4 Research

Research engineers from the Cryogenics Test Laboratory at NASA Kennedy Space Center in Florida have developed a 400 liter Integrated Refrigeration and Storage (IRAS) cryostat to explore advanced techniques for storage, conditioning, and transfer of liquefied natural gas and/or pure methane. A vertical-cylindrical configuration, the vacuum-jacketed apparatus houses a G-M cryocooler to control the state of the fluid, and sample tubes with corresponding temperature sensors fixed at various elevations to allow for sampling of the liquid. Two additional ports were also included for future instrumentation and/or mechanical feed-throughs. A primary goal of this test apparatus will be to study the effect of IRAS on the behavior of LNG during storage; most notably weathering and stratification of the bulk liquid over time. Additionally, in-situ liquefaction of natural gas can be performed, along with zero boil-off control, liquid densification, and slush production.

Swanger, Adam M.↗
NASA NTRS1976

Inelastic scattering of 61 MeV protons by pb-207

Differential cross sections for the excitation of the first four neutron-hole states and the doublet at 2.61 MeV by 61.2 MeV protons were measured. The data are analyzed in terms of both a purely collective model description and a microscopic model supplemented by macroscopic core polarization. A realistic two-body interaction is used and knock-on amplitudes are included. Core polarization is found to be important but represents a relatively smaller contribution than in most nuclei previously studied. A parallel analysis of similar data at lower proton bombarding energies reveals a surprisingly strong energy dependence of the reaction mechanisms.

Owais, M.↗
NASA NTRS1988

A new laboratory source of ozone and its potential atmospheric implications

Although 248-nm radiation falls 0.12 eV short of the energy needed to dissociate O2, large densities of ozone (O3) can be produced from unfocused 248-nm KrF excimer laser irradiation of pure O2. As soon as any O3 is present, it strongly absorbs the 248-nanometer radiation and dissociates to vibrationally excited ground state O2 (among other products), with a quantum yield of 0.1 to 0.15. During the laser pulse, a portion of these molecules absorb a photon and dissociate, which results in the production of three oxygen atoms for one O3 molecule destroyed. Recombination then converts these atoms to O3, and thus O3 production in the system is autocatalytic. A deficiency exists in current models of O3 photochemistry in the upper stratosphere and mesosphere, in that more O3 is found than can be explained. A detailed analysis of the system as it applies to the upper atmosphere is not yet possible, but with reasonable assumptions about O2 vibrational distributions resulting from O3 photodissociation and about relaxation rates of vibrationally excited O2, a case can be made for the importance of including this mechanism in the models.

Slanger, T. G.↗
NASA NTRS1994

NLTE model stellar atmospheres with line blanketing near the series limits

In this paper we study the influence of line-merging regions at the intermediate long-wavelength side of a continuum threshold on the computed model atmosphere structure and predicted spectrum. In order to model these regions sufficiently accurately, we have developed two concepts. First, we have extended the occupation probability formalism of Hummer and Mihalas to non-local thermodynamic equilibrium (non-LTE) plasmas. Second, in order to treat the very complicated opacity in the line merging region, we have generalized the concept of opacity distribution functions to treat non-LTE situations. All Rydberg states are consistently included within this framework, so that no arbitrary cutoff of high (LTE) levels is made. We have calculated several pure hydrogen models atmospheres for two effective temperatures, T(sub eff) = 20000 and 35000 K, and discussed the differences between models calculated with various treatments of the line merging. In particular, we have shown that the error in the predicted profiles of Balmer lines resulting from the neglect of line merging is typically of the order of 3-4%, while the errors in the far-UV portion of the Balmer continuum reaches 15-35%. The errors generally decrease with increasing effective temperature. At the same time, the internal accuracy of the models is shown to be about or below 0.5% for all predicted spectral features. We conclude that for interpreting current high-accuracy spectrophotometric observations models including the line merging are necessary, and that the formalism developed in this paper is capable of providing a sufficiently accurate and robust modeling technique.

Hubeny, I.↗
NASA NTRS1995

Space flight data from the isothermal dendritic growth experiment

The Isothermal Dendritic Growth Experiment (IDGE) is a NASA space flight experiment which flew as part of the United States Microgravity Payload (USMP-2), in early 1994. The IDGE measured dendritic growth rates, tip radii, and crystal morphologies of ultra-pure succinonitrile (CN-(CH2)2-CN) at supercoolings in the range from 0.05 - 2.0 K. Data taken in the form of slow-scan binary digitized images telemetered to the ground from orbit in near-real time, combined with the IDGE terrestrial data set, provide the first quantitative assessment of various theories on dendritic solidification and the effects of convection on dendritic growth.

Glicksman, M. E.↗
NASA NTRS1993

Statistics of Experiments on Cluster Formation and Transport in a Gravitational Field

Metastable state relaxation in a gravitational field is investigated in the case of non-critical binary solutions. A relaxation description is presented in terms of the time-dependent Ginzburg-Landau formalism for a non-conserved order parameter. A new ansatz for solution of the corresponding partial nonlinear stochastic differential equation is discussed. It is proved that, for the supersaturated solution under consideration, the metastable state relaxation in a gravitational field leads to formation of solute concentration gradients due to the sedimentation of subcritical solute clusters. The pure discussion of the possible methods to compare theoretical results and experimental data related to solute sedimentation in a gravitational field is presented. It is shown that in order to describe these experiments it is necessary to deal both with the value of the solute concentration gradient and with its formation rate. The stochastic nature of the sedimentation process is shown.

Izmailov, Alexander F.↗
NASA NTRS2005

Water as a matrix for life

Life is based on non-covalent interactions. They might be either specific (enzyme-substrate interactions, selective ion transport) or nonspecific (lipid-lipid and lipid-protein interactions needed for membrane integrity, fusion and division). Their strength needs to be properly tuned, and this is mediated by the solvent. If interactions are too weak, there might be undesired response to natural fluctuations of physical and chemical parameters. If they are too strong it could impede kinetics and energetics of cellular processes. Thus, the solvent must allow for balancing these interactions. Physical and chemical properties of solvent provide strong constraints for life. Water exhibits a remarkable trait that it promotes both solvophobic and solvophilic interactions. Solvophobic interactions; related to high dielectric constant of the solvent) are necessary for self-organization of matter whereas solvophilic interactions are needed to ensure solubility of polar species. Water offers a large temperature domain of stable liquid and the characteristics hydrophobic effects are a consequence of the temperature in sensitivity of essential properties of its liquid state. Water, however, is not the only liquid with these favorable properties. I will compare in detail properties of water and other pure liquids or their mixtures that have a high dielectric constant and simultaneously support self-organization. I will also discuss properties of water that are unfavorable to life (e.g. its chemical activity against polymerization reactions) and close with summarizing what are alternatives to water as a matrix of life in space.

Pohorille, Andrew↗
NASA NTRS2001

Dendritic Alloy Solidification Experiment (DASE)

A space experiment, and supporting ground-based research, is proposed to study the microstructural evolution in free dendritic growth from a supercooled melt of the transparent model alloy succinonitrile-acetone (SCN-ACE). The research is relevant to equiaxed solidification of metal alloy castings. The microgravity experiment will establish a benchmark for testing of equiaxed dendritic growth theories, scaling laws, and models in the presence of purely diffusive, coupled heat and solute transport, without the complicating influences of melt convection. The specific objectives are to: determine the selection of the dendrite tip operating state, i.e. the growth velocity and tip radius, for free dendritic growth of succinonitrile-acetone alloys; determine the growth morphology and sidebranching behavior for freely grown alloy dendrites; determine the effects of the thermal/solutal interactions in the growth of an assemblage of equiaxed alloy crystals; determine the effects of melt convection on the free growth of alloy dendrites; measure the surface tension anisotropy strength of succinon itrile -acetone alloys establish a theoretical and modeling framework for the experiments. Microgravity experiments on equiaxed dendritic growth of alloy dendrites have not been performed in the past. The proposed experiment builds on the Isothermal Dendritic Growth Experiment (IDGE) of Glicksman and coworkers, which focused on the steady growth of a single crystal from pure supercooled melts (succinonitrile and pivalic acid). It also extends the Equiaxed Dendritic Solidification Experiment (EDSE) of the present investigators, which is concerned with the interactions and transients arising in the growth of an assemblage of equiaxed crystals (succinonitrile). However, these experiments with pure substances are not able to address the issues related to coupled heat and solute transport in growth of alloy dendrites.

Beckermann, C.↗
NASA NTRS1989

Steady-state thermal-solutal diffusion in a float zone

A model for a float zone in a thin vertical sheet is used to study the formation of the zone configuration for both pure and binary systems of Si and GeGa. Equations describing the steady two-dimensional diffusion of solute in the melt and diffusion of heat in the feed material and the product crystal are presented. The material properties, asymptotic solutions for the temperature and concentration profiles, and melting, solidifying, and melt/gas interfacial shapes are determined in the small aspect ratio limit.

Young, G. W.↗
NASA NTRS1981

Evaluation of boundary lubricants using steady-state wear and friction

A friction and wear study was made at 20 C to establish operating limits and procedures for obtaining improved reproducibility and reliability in boundary lubrication testing. Ester base and C-other base fluids were used to lubricate a pure iron rider in sliding contact with a rotating M-50 steel disk in a pin-on-disk apparatus. Results of a parametric study with varying loads and speeds slowed that satisfactory test conditions for studying the direction and wear characteristics in the boundary lubrication regime with this test device were found to be 1 kilogram load; 7 to 9 meters-per-minute (50 rpm) surface speed; dry air test atmosphere (less than 100 ppm H2O); and use of a time stepwise procedure for measuring wear. Highly reproducible steady-state wear rates resulted from the two fluid studies which had a linearity of about 99 percent after initially higher wear rates and friction coefficients during run-in periods of 20 to 40 minutes.

Loomis, W. R.↗
NASA NTRS1973

Theoretical model of vertical distributions of CO and CH4 in the mesosphere and upper stratosphere.

Carbon compounds (CO and CO2) and methane are added to an existing computer program (Shimazaki and Laird, 1970, 1972), which calculates diurnal variations in density distributions of pure oxygen compounds, hydrogen compounds, and nitrogen compounds. For the present model calculations, the original program was modified to calculate the steady-state profiles for all constituents, and then these solutions were used as the initial condition for solving the time-dependent equations. The effects of chemical reactions and vertical eddy diffusion transport on the CH4 and CO concentrations above 40 km, where one-dimensional treatment may not be too inappropriate, are discussed. Some of the 15 constituents included in the computer program interact with CO and CH4 chemically, and CH4 is more sensitive to the eddy diffusion coefficient than any other constituent. Therefore it is easier to determine the most appropriate profile of the eddy diffusion coefficient by comparing the model profile with the observations for CH4.

Shimazaki, T.↗
NASA NTRS1993

Effect of micron-sized roughness on transition in swept-wing flows

Boundary-layer transition-to-turbulence studies are conducted in the Arizona State University Unsteady Wind Tunnel on a 45-degree swept airfoil. The pressure gradient is designed so that the initial stability characteristics are purely crossflow-dominated. Flow visualization and hot-wire measurements show that the development of the crossflow vortices is influenced by roughness near the attachment-line. Comparisons of transition location are made between a painted surface, a machine-polished surface, and a hand-polished surface. Then, isolated 6 micron roughness elements are placed near the attachment line on the airfoil surface under conditions of the final polish (0.25 micron rms). These elements amplify a centered stationary crossflow vortex and its neighbors, resulting in localized early transition. The diameter, height, and location of these roughness elements are varied in a systematic manner. Spanwise hot-wire measurements are taken behind the roughness element to document the enhanced vortices. These scans are made at several different chord locations to examine vortex growth.

Radeztsky, Ronald H., Jr.↗
NASA NTRS2008

Thermal Stir Welding Development at Marshall Space Flight Center

Solid state welding processes have become the focus of welding process development at NASA's Marshall Space Flight Center. Unlike fusion weld processes such as tungsten inert gas (TIG), variable polarity plasma arc (VPPA), electron beam (EB), etc., solid state welding processes do not melt the material during welding. The resultant microstructure can be characterized as a dynamically recrystallized morphology much different than the casted, dentritic structure typical of fusion weld processes. The primary benefits of solid state processes over fusion weld processes include superior mechanic properties and the elimination of thermal distortion and residual stresses. These solid state processes attributes have profoundly influenced the direction of advanced welding research and development within the NASA agency. Thermal Stir Welding (TSW) is a new solid state welding process being developed at the Marshall Space Flight Center. Unlike friction stir welding, the heating, stirring and forging elements of the weld process can be decoupled for independent control. An induction coil induces energy into a workpiece to attain a desired plastic temperature. An independently controlled stir rod, captured within non-rotating containment plates, then stirs the plasticized material followed by forging plates/rollers that work the stirred weld joint. The independent control (decoupling) of heating, stirring and forging allows, theoretically, for the precision control of microstructure morphology. The TSW process is being used to evaluate the solid state joining of Haynes 230 for ARES J-2X applications. It is also being developed for 500-in (12.5 mm) thick commercially pure grade 2 titanium for navy applications. Other interests include Inconel 718 and stainless steel. This presentation will provide metallurgical and mechanical property data for these high melting temperature alloys.

Ding, Robert J.↗
NASA NTRS2022

Novel Processing, Testing and Characterization of Copper/Carbon Nanotube (Cu/CNT) Yarn Composite Conductor

Sustainable electrified aircraft propulsion (EAP) is likely to lead to an increase in the electrical wiring contained within a single aircraft. Since the electrical resistance and mass of copper (Cu) conductors are associated with power losses, it is desirable to design high-conductivity lightweight conductor materials, thus reducing the mass of components like motor windings, low-voltage signal cables, and transmission cables for data and power to improve the overall energy efficiency. This paper describes a unique framework for manufacturing metalized carbon nanotube (CNT) composite conductors, measuring their electrical conductivity and strength, and modeling the overall conductivity and current sharing within such composites. Tensile testing was conducted on the processed composite conductor cables with the use of acoustic emission and electrical resistivity to determine stress-dependent-failure mechanisms while monitoring the electrical conductivity. The average of measured electrical conductivities of annealed Cu/CNT samples from batch 5 was greater than theoretical predictions by 9.8 percent and was also greater than the conductivity of pure annealed Cu by 4.8 percent and had comparable ultimate tensile strengths. Additionally, those Cu/CNT samples provide a 13.5% weight saving over current state of the art copper wires. Theories explaining improved intrinsic conductivity are discussed.

Metalized CNT↗
NASA NTRS1980

Steady-state wear and friction in boundary lubrication studies

A friction and wear study was made at 20 C to obtain improved reproducibility and reliability in boundary lubrication testing. Ester-base and C-ether-base fluids were used to lubricate a pure iron rider in sliding contact with a rotating M-50 steel disk in a friction and wear apparatus. Conditions included loads of 1/2 and 1 kg and sliding velocities of 3.6 to 18.2 m/min in a dry air atmosphere and stepwise time intervals from 1 to 250 min for wear measurements. The wear rate results were compared with those from previous studies where a single 25 min test period was used. Satisfactory test conditions for studying friction and wear in boundary lubrication for this apparatus were found to be 1 kg load; sliding velocities of 7.1 to 9.1 m/min (50 rpm disk speed); and use of a time stepwise test procedure. Highly reproducible steady-state wear rates and steady-state friction coefficients were determined under boundary conditions. Wear rates and coefficients of friction were constant following initially high values during run-in periods.

Loomis, W. R.↗
NASA NTRS1980

Gas phase hydrogen permeation in alpha titanium and carbon steels

Commercially pure titanium and heats of Armco ingot iron and steels containing from 0.008-1.23 w/oC were annealed or normalized and machined into hollow cylinders. Coefficients of diffusion for alpha-Ti and alpha-Fe were determined by the lag-time technique. Steady state permeation experiments yield first power pressure dependence for alpha-Ti and Sievert's law square root dependence for Armco iron and carbon steels. As in the case of diffusion, permeation data confirm that alpha-titanium is subject to at least partial phase boundary reaction control while the steels are purely diffusion controlled. The permeation rate in steels also decreases as the carbon content increases. As a consequence of Sievert's law, the computed hydrogen solubility decreases as the carbon content increases. This decreases in explained in terms of hydrogen trapping at carbide interfaces. Oxidizing and nitriding the surfaces of alpha-titanium membranes result in a decrease in the permeation rate for such treatment on the gas inlet surfaces but resulted in a slight increase in the rate for such treatment on the gas outlet surfaces. This is explained in terms of a discontinuous TiH2 layer.

Johnson, D. L.↗
NASA NTRS1972

Abnormal grain growth in TD-nickel.

Characteristics of the coarse grain transformation occurring in TD-nickel 1 in. bar under certain conditions of deformation and annealing were examined. The transformation exhibits Avrami-type kinetics, with an activation energy of 250 kcal per mole. Characteristics of untransformed regions are like those of the as-received state. The transformed grain size increases with increasing deformation and decreasing annealing temperature. The coarse grain transformation is significantly different from primary recrystallization in pure nickel. Its characteristics cannot be rationalized in terms of primary recrystallization concepts, but may be explained in terms of an abnormal grain growth description. The coarse grain transformation in TD-nickel is abnormal grain growth rather than primary recrystallization. The analysis suggests an explanation for the effect of thermomechanical history on the deformation and annealing behavior of TD-nickel.

Petrovic, J. J.↗
NASA NTRS1988

Laboratory detection of a new interstellar free radical CH2CN(2B1)

An asymmetric-top free radical CH2CN with a 2B1 ground state was detected by laboratory microwave spectroscopy. The radical was produced in a free-space absorption cell by a DC glow discharge in pure CH3CN gas. About 60 fine-structure components were observed for the N = 11-10 to 14-13 a-type rotational transitions in the frequency region of 220-260 GHz. Hyperfine resolved components for the N = 4-3 and 5-4 transitions were resolved in the 80 and 100 GHz regions, respectively. Molecular constants were determined and U100602 and U80484 from Sgr B2, and U40240 and U20120 from TMC-1 were assigned to the N = 5-4, 4-3, 2-1, and 1-0 transitions with K(-1) = 0 of the CH2CN radical.

Saito, Shuji↗