Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “POINT SOURCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A simulation-based model studying monoethanolamine and aprotic heterocyclic anion ionic liquid (AHA-IL) mixtures for carbon capture

Capturing of waste CO 2 , particularly from large industrial point sources, is necessary for either permanent storage or CO 2 utilization. Amine solvents used for carbon capture have certain drawbacks, particularly the high energy required by the reboiler for solvent regeneration and degradation of the amine with absorption/regeneration cycling. These challenges may be overcome using ionic liquids (ILs) that can be tailored for operating under typical flue gas stream conditions (8–10% CO 2 , 18–20% H 2 O, 2–3% O 2 , and 67–72% N 2 ). ILs, however, oftentimes suffer from high viscosities, leading to diffusion limitations when compared to amine solvents. This work models the combinations of aprotic heterocyclic anion ILs (AHA-IL) with monoethanolamine (MEA) and studies the carbon capture effectiveness of these mixtures. Furthermore, this study found that all AHA-IL/MEA mixtures exhibited 32 % lower enthalpy of reaction (compared to MEA) and 64 % lower viscosity (compared to AHA-IL), which are desirable characteristics for CO 2 capture solvents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Carbon management technology pathways for reaching a U.S. Economy-Wide net-Zero emissions goal

The Carbon Management Study Group of the 37 th Energy Modeling Forum (EMF 37) designed seven scenarios to explore the role of three potentially key technology suites – point source carbon dioxide capture and storage (PSCCS), direct air capture of carbon dioxide (DACCS), and hydrogen systems (H 2 ) – in shaping the broader technology pathways to reaching net-zero carbon dioxide (CO 2 ) emissions in United States by 2050. Each scenario was run by up to 13 models participating in the EMF 37 study. Results show that carbon dioxide removal technologies were consistently a major part of successful pathways to net-zero U.S. CO 2 emissions in 2050. Achieving this net-zero CO 2 goal without any form of carbon dioxide capture and storage was found to be impossible for most models; some models also found it impossible to reach net-zero without DACCS. The marginal cost of achieving net-zero CO 2 emissions in 2050 was between two and 10 times higher without PSCCS and/or DACCS available. The carbon price at which DACCS was deployed as a backstop technology depended upon the assumed cost at which DACCS was available at scale. Carbon prices were between $\$$250 and $\$$500 per ton CO 2 when DACCS deployed as a backstop. The average CO 2 capture rate across all models in 2050 in the central net-zero scenario was 1.3 GtCO 2 /year, which implies a substantial upscaling of capacity to move and store CO 2 . Finally, hydrogen sensitivity scenarios showed that H 2 typically constituted a relatively small share of the overall U.S. energy system; however, H 2 deployed in applications that are considered hard to decarbonize, facilitating transition towards net-zero emissions.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Innovative use of CaO in combination with amino acid salt to convert CO 2 as CaCO 3 nanoparticles under mild pH and low temperature

The increasing demand for sustainable CO 2 management has driven the development of innovative methods that can convert point source CO 2 into value-added products. In this study, CaO in combination with amino acid salt was used to convert CO 2 into CaCO 3 nanoparticles. Different from the conventional method where CO 2 diffusion presents a major challenge in reacting with CaO to form CaCO 3 , amino acid salt solvent was applied to absorb CO 2 first and then rapidly reacted with CaO to form CaCO 3 nanoparticles (∼50 nm) at a low temperature (e.g., 60 °C). Our experiments showed that at a glycine (Gly)/NaOH ratio of 2:1 or 3:1, the solution pH values during the CO 2 absorption and conversion were about 8–9 at 60 °C, while at a ratio of 1:1, the solution pH values were about 9–11; without Gly, the solution pH values were about 12. Gly-optimized solvent substantially reduced corrosion risk to reactors. In addition, the use of amino acid (i.e., Gly) led to much smaller CaCO 3 particles, distinctly different chemical phases, and fundamentally different chemical reactions. Moreover, in the presence of Gly, the solution pH was completely reversed and the solution was regenerated for cyclic use when CaO was added. The solvent was recyclable and reusable, highlighting the cost-effectiveness and sustainability of this approach. The Gly-modulated CaCO 3 nanoparticles may have significant potential for industrial applications in the biomedicine, construction, plastics, and rubber industries.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Discrete fracture network model benchmarks developed and applied in a DECOVALEX-2023 repository performance assessment study

This study presents newly developed benchmarks for modeling flow and transport within discrete fracture networks (DFNs) and useful methods for analyzing the results. The new benchmarks are designed to test modeling approaches for use in probabilistic performance assessment models of deep geologic repositories in fractured rock. The benchmarks simulate flow and transport through a 1 km 3 block of fractured rock. The first simulates migration of a short pulse of tracer through a simple network of four intersecting fractures. The second adds 1089 stochastically generated fractures. The third changes the pulse to a continuous point source. Evaluation of model performance relies on moment analysis and comparison of the results of different models. The expected nondimensional first moment of the conservative tracer for each benchmark is 1. The benchmarks were simulated by teams from Canada, Czechia, Germany, Korea, Sweden, Taiwan, and the United States as part of a DECOVALEX-2023 study (decovalex.org). The teams used various approaches, including explicit DFN modeling, DFN upscaling to an equivalent continuous porous medium (ECPM), and a combination of both methods. Transport mechanisms are modeled using either the advection-dispersion equation or particle tracking. Results demonstrate strong agreement among the models in breakthrough behavior up to the 75th percentile. Significant deviations in first moments and well-clustered outputs led to the identification of inaccuracies in several models. Such findings exemplify the benefit of exercising these benchmarks and using the presented methods to test DFN flow and transport models.

Benchmark↗
DOE OSTI2022

Assessment of oil and gas fields in California as potential CO 2 storage sites

California's total annual greenhouse gas (GHG) emissions (425.3 MtCO 2 e) in 2018 were about 6.4% of the US total (6,677 MtCO 2 e) and around 1% of global emissions. About 39% of 2018 GHG emissions in California were from the industrial and electrical sectors. Many of these emissions were from large stationary point sources and were suitable for carbon capture retrofit with subsequent storage of the captured carbon dioxide (CO 2 ) in geological formations. Previous studies of California found suitable geology and CO 2 storage resource. This study refines and furthers prior work using a three-stage screening process of oil fields, gas fields, and underground natural gas storage (UGS) sites by combining criteria from previous studies while excluding sites that pose technical risk or are located in regions with surface restrictions including sensitive habitats and dense populations. In the first stage, 129 CO 2 storage sites in California were identified using qualification criteria based upon formation properties including geological conditions and pore pressure. The second stage identified sensitive sites by applying conservative screens including seismic activity, faulting, population density, restricted lands, and sensitive habitats. During the third stage, 61 CO 2 potential storage sites were identified by subtraction of stage 2 areas from stage 1. The potential storage volume in the third stage ranged from 1.0 to 2.0 GtCO 2 . Finally, we applied a scoring system with seven parameters to rank the 61 potential sites based on subsurface technical criteria. The scored sites are classified as high priority, medium priority, and sites for future study. Prospective CO 2 storage sites with high and moderate priority were selected and linked to CO 2 sources. There are 14 prospective sites (above 20 MtCO 2 storage resource per site) with a total storage resource of 1024 MtCO 2 distributed in Northern and Southern California. Of these sites, there are 9 potential CO 2 -EOR sites and 1 depleted oil field with a total estimated CO 2 storage volume of ~800 MtCO 2 in the Southern San Joaquin and Ventura Basin. These 10 prospective sites with a storage resource greater than 20 MtCO 2 could potentially deliver more than 20 years of storage with an average injection rate of 40 MtCO 2 /year. The remaining 4 highly prospective sites are in Northern California. Additionally, study results suggest that saline formations should be re-evaluated in concert with storage in oil, gas, and natural gas storage reservoirs.

58 GEOSCIENCES↗
DOE OSTI2021

Evaluation of sequence tracking methods for Compton cameras based on CdZnTe arrays

In this study, the performance of sequence tracking methods for multiple interaction events in specific CdZnTe Compton imagers was evaluated using Monte Carlo simulations. The Compton imager consisted of a 6 × 6 array of virtual Frisch-grid CZT crystals, where the dimensions of each crystal were 5 × 5 × 12 mm 3 . The sequence tracking methods for another Compton imager that consists of two identical CZT crystals arrays were also evaluated. When 662 keV radiation was incident on the detectors, the percentages of the correct sequences determined by the simple comparison and deterministic methods for two sequential interactions were identical (~80 %), while those evaluated using the minimum squared difference method (55-59 %) and Three Compton method (45-55 %) for three sequential interactions, differed from each other. The reconstructed images of a 662 keV point source detected using single and double arrays were evaluated based on their angular resolution and signal-to-noise ratio, and the results showed that the double arrays outperformed single arrays.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Coregistered positron emission particle tracking (PEPT) and X-ray computed tomography (CT) for engineering flow measurements

Increasingly, fully 3D experimental measurements of flow in complex engineering geometries are required to validate computational fluid dynamics models that support and inform reactor design and licensing. One barrier to such measurements is the complexity of typical reactor components and subsequent lack of optical access in these systems. To overcome this, the deployment of coregistered positron emission particle tracking (PEPT) and X-ray computed tomography (CT) is explored for flow measurement in reactor thermal hydraulic components and model (scaled) systems. Through this methodology, fully 3D flow information (via PEPT) and detailed internal geometry (via CT) are captured in opaque systems such as pipes, rod bundles, packed beds, etc. The reconstructed flow field and geometry can then be overlain to reveal detailed flow features around internal structures within a given test section. This is enabled through the use of a combined preclinical PET/CT scanner with overlapping PET and CT fields of view. Such measurements are useful for characterizing flow inside such intricate nuclear thermal hydraulic components as core geometries and heat exchangers, among others, and providing valuable 3D validation data for CFD models. In this work, basic tests of this 3D flow/geometry mapping are presented, and the implications of such measurements are discussed. Further, preliminary measurements are made with both point sources and flow in a simple pipe flow geometry to evaluate the capabilities of this technique. PEPT and CT features are coregistered with up to 0.1 mm precision, and pipe flow mean velocity and Reynolds stresses are reconstructed with similar accuracy to previous PEPT demonstrations. The utility of PEPT/CT is shown herein, and suggestions for future measurements are made.

3D flow measurement↗
DOE OSTI2022

Mineral-hydrogel composites for mitigating harmful algal bloom and supplying phosphorous for photo-biorefineries

Harmful algal blooms (HAB) are a major environmental concern in eutrophic aquatic systems. To mitigate HABs and recover the phosphorus that drives algal growth, this study developed hydrogel composites seeded with calcium phosphate and wollastonite particles, which first adsorb phosphate (P) and then precipitate it as calcium phosphate. Using a fast-growing cyanobacterium, Synechococcus elongatus 2973, as a model microalga, we found that the mineral-hydrogel composites reduced dissolved P in BG11 media from 5.1 mg/L to 0.31 mg/L, initially reducing the biomass growth rate by up to 73 % and ultimately reducing the total biomass concentration by 75 %. When applied to municipal wastewater and agricultural run-off, the composites removed 96 % and 91 % of the dissolved P, respectively. Moreover, when the recovered P-enriched composites were reused as a slow-release bio-compatible fertilizer in a photobioreactor, they effectively supported algal growth without blocking light and interfering with photosynthesis. The P-enriched composites could tune the P concentration in the culture medium and significantly promote algal lipid accumulation. Finally, this study demonstrates the mineral-hydrogel composites' potential to treat point sources of P pollution and subsequently facilitate photoautotrophic biofuel production as a nutrient, effectively recycling the captured P.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Pronounced reduction in the regeneration energy of potassium sarcosinate CO 2 capture solvent using TiO 2

Absorption-based CO 2 capture technologies face economic feasibility concerns due to the exceedingly high energy requirements of solvent regeneration. Among various proposed solutions, solid acid-aided solvent regeneration stands out as a promising approach. Studies have shown that solid materials containing Lewis and Brønsted acid sites can facilitate deprotonation of protonated amine and breakdown of carbamate molecules, which significantly increases CO 2 desorption rate and decreases regeneration energy of common solvents such as MEA and DEA. However, the influence of solid acids on alternate solvents such as amino acids is not well known. Here, we report the performance of TiO 2 for the regeneration of CO 2 -loaded aqueous potassium sarcosinate (K-Sar) solvent. K-Sar is an environmentally friendly amino-acid salt that provides high CO 2 absorption rates, making it a good candidate for both point-source and direct-air capture. TiO 2 is hydrothermally stable and contains high surface acid site concentration. Desorption of CO 2 from K-Sar starts at room temperature in the presence of TiO 2 , while such onset temperature is greater than 70°C for regeneration without TiO 2 . Further, at a temperature of 95°C, the maximum CO 2 desorption rate and cumulative CO 2 removal increase by 128% and 91%, respectively, in the presence of TiO 2 compared to the no TiO 2 case. The total regeneration energy could be reduced by ~ 50% with TiO 2 , showcasing the significant role this process can take in improving the commercial competitiveness of absorption-based CO 2 capture. Further characterization with XRD, SEM, and NMR concluded that neither the TiO 2 powder nor the solvent undergoes any physical or chemical degradation in the regeneration process, suggesting the potential of their long-term usability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Big Data Analysis and Technical Review of Regeneration for Carbon Capture Processes

Carbon capture remains an integral technology to mitigate pollution from one of the most prevalent greenhouse gases. CO 2 desorption/absorbent regeneration for both solid- and liquid-based systems is widely recognized as an energy-intensive and costly process operation. Consequently, tremendous work was devoted towards developing new absorbents and regeneration processes to promote their economic feasibility for extensive implementation. In this review, we broadly and deeply review more than 10,000 papers and extract the hidden trends of carbon capture and absorbents regeneration in the past few decades, using a novel data-mining analysis technique. We comprehensively analyzed an array of recent absorbent regeneration methods utilized in post-combustion, pre-combustion, carbon capture from industrial point sources, and direct air carbon capture, with an emphasis on sorbent and solvent-based techniques. In conclusion, advanced regeneration methods in these techniques were illustrated and discussed, followed by recommendations for further research efforts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Reducing Economy-Wide Greenhouse Gas Emissions with Electrofuels and Biofuels as the Grid Decarbonizes

Biofuels and electrofuels have the potential to complement electrification in speeding greenhouse gas emissions reductions, especially in hard-to-decarbonize sectors. Concentrated waste CO 2 streams that can be used as a feedstock for electrofuels, however, may become less available as the share of renewable electricity increases and industries undergo decarbonization. Here, we conduct an analysis with detailed treatment of biofuels and electrofuels to probe their role in decarbonizing multiple industrial sectors and transportation. We examine how the changing availability of CO 2 could affect electrofuel production and the potential role of direct air capture in stabilizing the supply of CO 2 . The results indicate that biofuels could fulfill 12% of the total final energy demand across all U.S. sectors in 2050. Using seven industrial source points of CO 2 available in 2050, 15,388 PJ of electrofuels could be produced, which amounts to 25% of the total final energy demand. This result holds even upon decarbonization that requires direct air capture to boost the CO 2 supply. Biofuels and e-fuels have the potential to reduce economy-wide GHG emissions by 7 and 21% beyond electrification alone. However, electricity consumption and land use grow markedly with decarbonization at scale.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2026

A Review on Direct Air Capture of Carbon Dioxide: Sorbent Materials, Process Engineering, Industrial Scale-Up, and Future Perspectives

The relentless accumulation of anthropogenic greenhouse gases has driven atmospheric carbon dioxide concentrations to approximately 426 ppm, necessitating the aggressive deployment of negative-emission technologies to achieve net zero by 2050. Direct air capture (DAC) offers a scalable, location-independent approach to atmospheric carbon removal; however, it is fundamentally constrained by the significant thermodynamic barriers associated with capturing CO 2 from ultradilute ambient conditions, requiring minimum thermodynamic energy inputs substantially higher than those for postcombustion point sources. This comprehensive review critically examines the technological landscape of DAC, focusing on the interdependent triad of sorbent material design, contactor engineering, and regeneration thermodynamics. We evaluate the fundamental boundaries of adsorption, emphasizing that an optimal adsorption enthalpy and isosteric heat of adsorption must balance the high CO 2 uptake capacity with the energetic penalties of sorbent regeneration. A systematic, comparative analysis of state-of-the-art sorbents is presented, encompassing mesoporous silicas, zeolites, carbon-based materials (CBMs), metal−organic frameworks (MOFs), porous organic polymers (POPs), and polymeric membranes. Special attention is devoted to surface functionalization strategies, particularly amine grafting and impregnation, which transition capture mechanisms from physisorption to chemisorption to enhance selectivity under ambient moisture and low partial pressures. Furthermore, we assess the operational merits of various reactor configurations, including gas−solid, gas−liquid, and membrane contactors, alongside regeneration cycles such as temperature, vacuum, pressure, and moisture swing adsorption. Finally, the review bridges fundamental materials science with industrial application by chronicling the scale-up milestones of pioneering entities and providing a strategic roadmap for advancing DAC technology readiness levels toward global deployment.

Adsorption↗
DOE OSTI2021

Interactions of an Imine Polymer with Nanoporous Silica and Carbon in Hybrid Adsorbents for Carbon Capture

Efficient carbon capture from stationary point sources can be achieved using hybrid adsorbents comprising nanoporous substrates coated with imine polymers. The physical properties of the CO 2 -adsorbing, nanodispersed polymers are altered by their interactions with the substrate, which in turn may impact their capture capacity. We study silica and carbon nanoporous substrates with different pore morphologies that were impregnated with polymer imine with the goal of characterizing the polymer dispersions in the pores. For silica and carbon samples, the mean densities of confined poly(ethylene imine) (PEI) were measured as functions of polymer loading and temperature using small-angle neutron scattering. Strong densification is found for imine polymers imbibed in mesoporous carbon. PEI in nanoporous silica does not experience this strong densification. At high loadings, plugs form, preferably at the pore throats, and can reduce accessible porosity. CO 2 capture measurements show that PEI interactions with the substrate play an important role. In conclusion, PEI in carbon shows the highest capture capacity at low temperatures and the lowest CO 2 adsorption at high temperatures, making it well-suited for temperature swing adsorption applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Improved CO 2 Capture Performance of Electrochemically Mediated Amine Regeneration Processes with Ionic Surfactant Additives

For the effective reduction of global CO 2 emissions, it is essential to develop and deploy efficient and cost-effective technologies for CO 2 capture, especially from large point sources. We recently developed an electrochemically mediated amine regeneration (EMAR) system to replace traditional thermal desorption for the capture of CO 2 from post-combustion flue gases. Despite EMAR effectiveness on a laboratory scale, concerns regarding the high gas-to-liquid ratio in the electrochemical cell and long-term instability of the electrodes need to be addressed before further scale-up of the process to a pilot plant and beyond can be entertained. Accordingly, we investigated the effect of using sodium dodecyl sulfate (SDS) as an anionic surfactant and dodecyltrimethylammonium bromide (DTAB) as a cationic surfactant on the process operation. It was found that it is advantageous to use an anionic surfactant for a system such as EMAR that contains hydrophilic electrodes and a positively charged electrochemically active species. The overall cell resistance was notably reduced when SDS anionic surfactant was used. The precipitation of copper particles observed in the anode outlet when no surfactant was used was effectively avoided when SDS was added to the electrolyte, resulting in electrode stability. In addition, smaller gas bubbles were produced in the presence of the SDS surfactant, which resulted in less blockage of the electrode by the gas with a resultant lower cell potential under constant current conditions, driving more efficient CO 2 desorption. This led to an ~25% reduction in the electrochemical energy requirement, the lowest ever achieved experimentally for the EMAR process. Altogether, the addition of a very low concentration of SDS resulted in the successful circumvention of the important problems faced by the EMAR system regarding further scale-up.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Continuum Model to Define the Chemistry and Mass Transfer in a Bicarbonate Electrolyzer

Bicarbonate electrolyzers are devices designed to convert CO 2 captured from point sources or the atmosphere into chemicals and fuels without needing to first isolate pure CO 2 gas. In this work, we report here an experimentally validated model that quantifies the reaction chemistry and mass transfer processes within the catalyst layer and cation exchange membrane layer of a bicarbonate electrolyzer. Our results demonstrate that two distinct chemical microenvironments are key to forming CO at high rates: an acidic membrane layer that promotes in situ CO 2 formation and a basic catalyst layer that suppresses the hydrogen evolution reaction. We show that the rate of CO product formation can be increased by modulating the catalyst and membrane layer properties to increase the rate of in situ CO 2 generation and transport to the cathode. These insights serve to inform the design of bicarbonate and BPM-based CO 2 electrolyzers while demonstrating the value of modeling for resolving rate-determining processes in electrochemical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Maximum and Comparative Efficiency Calculations for Integrated Capture and Electrochemical Conversion of CO 2

CO 2 as a C1 feedstock is receiving increasing attention, but it typically exists in dilute or impure streams. The capture and conversion of CO 2 to fuels or chemicals using carbon-neutral energy mitigates carbon emissions when CO 2 is captured from point sources and results in net or negative carbon emissions when CO 2 is obtained by direct air capture. Additionally, CO 2 capture and conversion steps are typically viewed as separate processes that optimize either capture and concentration or catalytic conversions of pure streams of CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Plastic Waste Product Captures Carbon Dioxide in Nanometer Pores

We discuss, plastic waste (PW) and increasing atmospheric carbon dioxide (CO 2 ) levels are among the top environmental concerns presently facing humankind. With an ambitious 2050 zero-CO 2 emissions goal, there is a demand for economical CO 2 capture routes. Here we show that the thermal treatment of PW in the presence of potassium acetate yields an effective carbon sorbent with pores width of 0.7–1.4 nm for CO 2 capture. The PW to carbon sorbent process works with single or mixed streams of polyolefin plastics. The CO 2 capacity of the sorbent at 25 °C is 17.0 ± 1.1 wt % (3.80 ± 0.25 mmol g –1 ) at 1 bar and 5.0 ± 0.6 wt % (1.13 ± 0.13 mmol g –1 ) at 0.15 bar, and it regenerates upon reaching 75 ± 5 °C. The CO 2 capture cost from flue gas via this technology is estimated to be <$21 ton –1 CO 2 , much lower than competing CO 2 capture technologies. Hence, this PW-derived carbon material should find utility in the capture of CO 2 from point sources of high CO 2 emissions while providing a use for otherwise deleterious PW.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Enhancing Selective Hydrofluorocarbon Greenhouse Gas Capture via Halogenation of Metal–Organic Frameworks

Hydrofluorocarbons (HFCs) are anthropogenically produced greenhouse gases with longer atmospheric lifetimes and higher global warming potentials than those of carbon dioxide. General strategies to abate their emissions from industrial point sources, such as via adsorptive capture, remain scarce. Herein, we uncover the key structure–property relationships that lead to strong binding of HFCs such as fluoroform (CHF 3 ) and difluoromethane (CH 2 F 2 ) in metal–organic frameworks (MOFs) under the low pressures relevant to flue gas scrubbing. Extensive gas sorption and computational studies support that the Zr-based microporous framework MOF-801-Br or HHU-2-Br (HHU = Heinrich-Heine-University Düsseldorf) strongly binds HFCs due to its synergistic combination of Zr-OH sites on the nodes and bromine sites on the linkers. As such, MOF-801-Br demonstrates a record-setting performance for separating CHF 3 from N 2 under dilute conditions. Our work highlights that the combination of multiple hydrogen-bonding sites in microporous MOFs represents a generalizable strategy for HFC capture, enabling their selective removal from industrial waste streams.

adsorption↗