Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA COMPOSITION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

The role of gas composition in plasma-dust structures in RF discharge

The influence of a mixture of light and heavy gases, i.e., helium and argon, on plasma-dust structures in the radiofrequency discharge has been studied. The dust chains in the sheath of the radiofrequency discharge, the average distance between the dust particles and their chains, have been analyzed. A significant effect of small amounts of argon on the correlation characteristics of dust particles has been observed. The results of numerical simulation of ion and electron drift in the mixture of helium and argon are presented. It is shown that even 1% of argon admixture to helium produces such an effect that argon ions become the main components of the discharge, as they drift with lightweight helium forming a strongly anisotropic velocity distribution function.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Study of the impurity composition and effective plasma charge in the GOL-3 facility

Heating and confinement of plasma in a multimirror magnetic configuration have been studied at the GOL-3 facility (Budker Institute of Nuclear Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk). The experiments are aimed at estimating the densities and charge states of the main impurities in the GOL-3 plasma and determining their contribution to the effective plasma charge. Plasma with a density of ∼10{sup 15} cm{sup −3} was heated by a relativistic electron beam (1 MeV, 8 μs, ⩽200 kJ). At the end of electron beam injection, the plasma temperature reached 1 keV. The densities of impurities were determined using VUV and visible spectroscopy, as well as mass spectrometry of the residual vacuum. To determine the effective plasma charge, the experimental data were compared with the results of numerical simulations of the ionization balance of impurities. It is shown that the effective plasma charge calculated with allowance for the contributions from the main impurities does not exceed Z{sub eff} = 1.8, which cannot explain the experimentally observed improved confinement of low-density plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Energetic ion composition of the plasma sheet

Data obtained from the energetic ion mass spectrometer experiment on Isee 1 in the distant plasma sheet are presented. These data show that (1) the plasma sheet has a significant and variable ionospheric component (H(+) and O(+)) representing from 10% to more than 50% of the total number density and (2) there is more than one process responsible for the energization of solar wind plasma (H(+) and He(++)) to plasma sheet energies.

Peterson, W. K.↗

Friction and Wear Characteristics of a Modified Composite Solid Lubricant Plasma Spray Coating

LCR304 is a solid lubricant coating composed of Ni-10Cr, Cr2O3, BaF2-CaF2 and Ag and developed for dimensional stability in high temperature air. This coating is a modification of PS304, which differs in that the Ni-Cr constituent contains 20wt% Cr. The tribological characteristics of LCR304 were evaluated by pin-on-disk and foil air bearing rig testing from 25 to 650 C and compared to previous test results with PS304. For both tests, the friction coefficient decreased as temperature increased from 25 to 650 C. Wear generally decreased with increasing temperature for all pin-on-disk tests. LCR304 coated components produced the least wear of Inconel X-750 counterface materials at 427 and 650 C. These results indicate that the LCR304 coating has potential as a replacement for PS304 in, for example, low cycle (minimum wear) applications where dimensional stability is imperative.

Stanford, M. K.↗

High density UO 2 and high thermal conductivity UO 2 composites by spark plasma sintering (SPS)

Embodiments of the invention are directed to a method for production of a nuclear fuel pellet by spark plasma sintering (SPS), wherein a fuel pellet with more than 80% TD or more than 90% TD is formed. The SPS can be performed with the imposition of a controlled uniaxial pressure applied at the maximum temperature of the processing to achieve a very high density, in excess of 95% TD, at temperatures of 850 to 1600° C. The formation of a fuel pellet can be carried out in one hour or less. In an embodiment of the invention, a nuclear fuel pellet comprises UO 2 and a highly thermally conductive material, such as SiC or diamond.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High density UO2 and high thermal conductivity UO2 composites by spark plasma sintering (SPS)

Embodiments of the invention are directed to a method for production of a nuclear fuel pellet by spark plasma sintering (SPS), wherein a fuel pellet with more than 80% TD or more than 90% TD is formed. The SPS can be performed with the imposition of a controlled uniaxial pressure applied at the maximum temperature of the processing to achieve a very high density, in excess of 95% TD, at temperatures of 850 to 1600° C. The formation of a fuel pellet can be carried out in one hour or less. In an embodiment of the invention, a nuclear fuel pellet comprises UO 2 and a highly thermally conductive material, such as SiC or diamond.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Soft Magnetic Multilayered FeSiCrB–Fe$_{x}$N Metallic Glass Composites Fabricated by Spark Plasma Sintering

Novel multilayered FeSiCrB–Fe $_{x}$ N ( x = 2–4) metallic glass composites were fabricated using spark plasma sintering of FeSiCrB amorphous ribbons (Metglas 2605SA3 alloy) and Fe $_{x}$ N ( x = 2–4) powder. Crystalline Fe $_{x}$ N can serve as a high magnetic moment, high electrical resistance binder, and lamination material in the consolidation of amorphous and nanocrystalline ribbons, mitigating eddy currents while boosting magnetic performance and stacking factor in both wound and stacked soft magnetic cores. Stacking factors of nearly 100% can be achieved in an amorphous ribbon/iron nitride composite. FeSiCrB–Fe $_{x}$ N multilayered metallic glass composites prepared by spark plasma sintering have the potential to serve as a next-generation soft magnetic material in power electronics and electrical machines.

36 MATERIALS SCIENCE↗

Giotto data analysis: Electron plasma and heavy ion composition measurements at Comet Halley

This investigation involved the analysis of electron plasma and heavy ion composition measurements made by the COPERNIC (COmplete Positive ion, Electron, and Ram Negative Ion measurements near Comet Halley) plasma experiment during the close fly-by of Halley by the European Space Agency's Giotto spacecraft. The experiment provided measurements of the full 3-dimensional distribution of 10 eV-30 keV electrons, and mass analysis of cold cometary ions from 10-210 amu. The analysis of the COPERNIC data has yielded some remarkable results, including: The discovery of negatively charged ions in the inner coma; the discovery of far heavier (mass is greater than 50 amu) ions than predicted, dominated by complex molecular ions made up of C, H, O, and N; the discovery of an adiabatic heating effect on electrons from the compression of the solar wind plasma; the identification of several organic and sulfur bearing ions; and the discovery of a new 'mystery region' where electrons are accelerated to high energies. These discoveries were in addition to the detailed analysis of 'expected' features at Comet Halley. Although this grant has expired, analysis continues on the data at a low (unfunded) level, and it is expected that more significant results will be obtained. A bibliography of the papers resulting from this research is attached, and a copy of each paper is included.

Lin, Robert P.↗

Ion Composition in Saturn's Plasma Environment: Early Results from the Cassini Plasma Spectrometer

Prior to Cassini s arrival at Saturn, most of what was known about the composition of the plasma in Saturn s environment was derived from limited measurements by Pioneer 11 and Voyager 1 and 2 in 1979-1981[1-3]. The measurements reported here were made by the Cassini Plasma Spectrometer (CAPS) [4] during the first two Cassini orbits, including the closest approach to Saturn and the rings during the tour, and a close flyby of Titan. The CAPS instrument resolves ion energy/charge from 1 V to 50 kV and ion mass/charge from 1 to approx.100 amu/e, and it measures electron energy from 1 eV to 28 keV. Initial composition measurements of Saturn s magnetosphere show that protons dominate outside approx.8 R(sub s), while inside this radius the plasma is dominated by a mix of water-derived ions and N(+). Over the A and B rings a plasma layer is observed composed of O2(+) and O(+) . The close passage near Titan shows a rich network of both positive and negative molecular ions. We report preliminary analysis of these and other composition findings.

Reisenfeld, D. B.↗

Composition of the hot plasma near geosynchronous altitude

Although there were no direct measurements of the composition of the hot (keV) plasma at geosynchronous altitudes, the combination of other observations leads to the conclusion that, at least during geomagnetically disturbed periods, there are significant fluxes of ions heavier than protons in this region. Ion composition measurements below 8000 km altitude show upward streaming fluxes of both O(+) and H(+) ions in the L-region of the geosynchronous orbit. These observations are consistent with the conclusion that at least a portion of the total ion fluxes observed at geosynchronous altitude to be highly peaked near the magnetic field lines are heavier than protons and originate in the ionosphere.

Johnson, R. G.↗

Al{sub 2}O{sub 3}-TiC Composite Prepared by Spark Plasma Sintering Process: Evaluation of Mechanical and Tribological Properties

Al{sub 2}O{sub 3}-10TiC composites were synthesized by spark plasma sintering (SPS) process. Microstructural and mechanical properties of the composite reveal homogeneous distribution of the fine TiC particles in the matrix. The samples were produced with different sintering temperature, and it shows that the hardness and density gradually increases with increasing sintering temperature. Abrasion wear test result reveals that the composite sintered at 1500 °C shows high abrasion resistance (wt. loss ~ 0.016 g) and the lowest abrasion resistance was observed for the composite sample sintered at 1100 °C (wt. loss ~ 1.459 g). The profilometry surface roughness study shows that sample sintered at 1100 °C shows maximum roughness (R{sub a} = 6.53 µm) compared to the sample sintered at 1500 °C (R{sub a} = 0.66 µm) corroborating the abrasion wear test results.

36 MATERIALS SCIENCE↗

Thermal Conductivity and Thermal Gradient Cyclic Behavior of Refractory Silicate Coatings on SiC/SiC Ceramic Matrix Composites

Plasma-sprayed mullite and BSAS coatings have been developed to protect SiC/SiC ceramic matrix composites from high temperature environmental attack. In this study, thermal conductivity and thermal barrier functions of these coating systems are evaluated using a laser high-heat-flux test rig. The effects of water vapor on coating thermal conductivity and durability are studied by using alternating furnace and laser thermal gradient cyclic tests. The influence of laser high thermal-gradient cycling on coating failure modes is also investigated.

Zhu, Dongming↗

Protective coatings for high-temperature polymer matrix composites

Plasma-enhanced chemical vapor deposition was used to deposit silicon nitride on graphite-fiber-reinforced polyimide composites to protect against oxidation at elevated temperatures. The adhesion and integrity of the coating were evaluated by isothermal aging (371 C for 500 hr) and thermal cycling. The amorphous silicon nitride (a-SiN:H) coating could withstand stresses ranging from approximately 0.18 GPa (tensile) to -1.6 GPa (compressive) and provided a 30 to 80 percent reduction in oxidation-induced weight loss. The major factor influencing the effectiveness of a-SiN:H as a barrier coating against oxidation is the surface finish of the polymer composite.

Harding, David R.↗

Structural Evolution in Mechanically Alloyed and Spark Plasma Sintered Iron–0.15 wt.% MWCNT Composite

High-energy ball milling (HEBM) of mixtures of iron powder and multi-walled carbon nanotube (MWCNT) has been performed in an attempt to synthesize nano-grained steel. Even after exposure to a harsh HEBM conditions, the MWCNTs are seen to have retained their structural identity, and therefore, an MWCNT-reinforced steel matrix composite could be finally produced. Moreover, the study has revealed that the minor addition of copper leads to a significant reduction in grain size of ferrite in the so-produced steel matrix–MWCNT composite. It is also noticed that the fine grain structure of ferrite remains intact even after consolidation of the powder composite by spark plasma sintering, followed by hot forging. The micro-hardness values obtained for the composites (with/without copper) are observed as comparable with the submicron-grained steels, so far reported in the literature.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tantalum-tungsten oxide thermite composites prepared by sol-gel synthesis and spark plasma sintering

Energetic composite powders consisting of sol-gel derived nanostructured tungsten oxide were produced with various amounts of micrometer-scale tantalum fuel metal. Such energetic composite powders were ignition-tested and the results show that the powders are not sensitive to friction, spark and/or impact ignition. Initial consolidation experiments, using the High-Pressure Spark Plasma Sintering (HPSPS) technique, on the sol-gel derived nanostructured tungsten oxide produced samples with higher relative density than can be achieved with commercially available tungsten oxide. The sol-gel derived nanostructured tungsten oxide with immobilized tantalum fuel metal (Ta-WO{sub 3}) energetic composite was consolidated to a density of 9.17 g cm{sup -3} or 93% relative density. In addition, those samples were consolidated without significant pre-reaction of the constituents, thus retaining their stored chemical energy. (author)

36 MATERIALS SCIENCE↗

U 3 Si 2 and UO 2 composites densified by spark plasma sintering for accident-tolerant fuels

This work reports the synthesis and characterization of the U 3 Si 2 and UO 2 composites sintered by spark plasma sintering (SPS) with controlled microstructures for accident-tolerant fuel application. The U 3 Si 2 and UO 2 composites with different silicide and oxide ratios were synthesized by SPS at temperatures from 1000 to 1300 °C for 5 minutes. The microstructure and phase composition of the SPS densified composite fuels were characterized with scanning electron microscopy, X-ray diffraction (XRD), and energy dispersed spectroscopy (EDS). A systematic study of the thermal and mechanical properties was conducted using microhardness testing and laser flash apparatus, along with oxidation resistance measurements using thermogravimetric analysis (TGA). The results show that the synthesis of composite fuels can be achieved with a 90% theoretical density (TD) at 1000 °C and over 95% TD when sintered at 1300 °C. XRD and EDS results confirmed that the dominant phases in the composites are U 3 Si 2 and UO 2 . Improved physical density generally leads to improved hardness, fracture toughness, thermal diffusivity, and onset temperature during the oxidation process. U 3 Si 2 was found to play a dominant role in determining the mechanical and oxidation properties of the composite fuels, whereas UO 2 had a more important impact on controlling the thermal diffusivity of the composites. The composite with 50 wt% UO 2 sintered at 1300 °C displayed the onset oxidation temperature of 500 °C by dynamic oxidation testing using TGA at a ramp degree of 10 °C/min. The composite also achieved a high fracture toughness of ~3.5 MPa m ½ . Finally, these results highlight the potential of composite fuel forms densified by SPS with simultaneously enhanced fissile element density, fracture toughness, thermal transport properties, and oxidation resistance.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗