SEARCH · Engineering Papers

Results for “Notch”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1974

The failure of notched specimens of boron-fiber reinforced 6061 aluminum alloy

The effect of notches on the strength of boron fiber reinforced 6061 aluminum alloy was determined at room temperature, 300 F, and 600 F. Both unidirectional and cross-plied specimens were tested. The strengths of individual fibers were measured, and upper and lower bounds of composite strength were calculated using bundle theory. Fracture tests were performed on specimens containing center slots of various lengths, and the values of the critical stress intensity factor for initial crack propagation or final failure were calculated. For unidirectional specimens, these parameters depended on thickness; for cross-plied specimens, fairly constant values were obtained at room temperature. The cross-plied material invariably failed at a lower stress as the environmental temperature was raised.

Wright, M. A.↗

NASA NTRS1975

Application of boundary integral method to elastoplastic analysis of V-notched beams

The boundary integral equation method was applied in the solution of the plane elastoplastic problems. The use of this method was illustrated by obtaining stress and strain distributions for a number of specimens with a single edge notch and subjected to pure bending. The boundary integral equation method reduced the nonhomogeneous biharmonic equation to two coupled Fredholm-type integral equations. These integral equations were replaced by a system of simultaneous algebraic equations and solved numerically in conjunction with the method of successive elastic solutions.

Rzasnicki, W.↗

NASA NTRS1976

Progressive failure of notched composite laminates using finite elements

An incremental, nonlinear, finite element program capable of tracing the damage that occurs in a notched laminated composite, before ultimate failure takes place, is described. Computer predictions for the ultimate failure load and failure modes are compared to experimental results for two laminates containing holes and loaded in uniaxial tension. The comparison is quite favorable.

Nuismer, R. J.↗

NASA NTRS1976

Notched and Unnotched Fatigue Behavior of Angle-Ply Graphite/Epoxy Composites

The axial fatigue behavior of both notched and unnotched graphite/epoxy composites was studied. In unnotched studies, conducted on a 0/+ or - 30 3S AS/3501 laminate, S-N curves were determined for various stress ratios R using simply supported test specimens. Apparent fatigue limits in tension-tension (T-T) and compression-compression (C-C) cycling occurred at about 60% of the respective static strengths. The overall results were expressed in the form of a constant life diagram showing the relationship between mean stress and stress amplitude. The diagram illustrates a skew-symmetry in fatigue life caused by the relatively low compressive strength of the unrestrained test specimens used. In effect, a maximum in fatigue properties occurs at a positive value of mean stress. Results are of significance in situations where structural members are buckling or crippling critical in design.

Ramani, S. V.↗

NASA NTRS1977

Notch filter

A notch filter for the selective attenuation of a narrow band of frequencies out of a larger band was developed. A helical resonator is connected to an input circuit and an output circuit through discrete and equal capacitors, and a resistor is connected between the input and the output circuits.

Shelton, G. B.↗

NASA NTRS1977

Load-displacement measurement and work determination in three-point bend tests of notched or precracked specimens

Suggestions for testing of notched or cracked three-point bend specimens are presented which: (1) correct displacement measurement errors resulting from misalignment between the load applicator and specimen; (2) account for coincidental strains not associated with the work of crack extension; (3) simplify record analysis and processing; and (4) extend displacement gage range without sacrifice of sensitivity or accuracy. These testing details are particularly applicable to procedures in which the crack extension force is determined from the work done on the specimen.

Buzzard, R. J.↗

NASA NTRS1976

Plane-stress fracture of compact and notch-bend specimens

Thin-gaged or high toughness materials containing cracks usually fail in a ductile manner with nominal failure stresses approaching the ultimate strength of the material. For such materials, a two-parameter fracture criterion was developed. An equation which related the linear elastic stress-intensity factor, elastic nominal stress, and two material parameters has previously been derived and has been used as a fracture criterion for surface- and through-cracked specimens under tensile loading. In the present paper the two-parameter fracture criterion was rederived in a more general form and was extended to compact and notch-bend fracture specimens. A close correlation was found between experimental and calculated failure stresses.

Newman, J. C., Jr.↗

NASA NTRS1977

Fatigue damage in notched composite laminates

This communication describes the results of an experimental investigation of the fatigue characteristics of a boron-epoxy laminate containing an unloaded circular hole. The study focuses upon characterization of the fatigue damage incurred and its influence upon axial tensile residual strength. Two apparent anomalies in the fatigue behavior for this laminate were observed. First, the fatigue damage was observed to propagate tangentially to the edge of the notch (parallel to the direction of the load), in contrast to propagation in contemporary metallic materials which is perpendicular to the load direction. Second, the residual strength characteristics for the laminate have revealed a significant increase in residual strength subsequent to a fatigue loading of 500,000 cycles at R = 0.1 and S = 0.8 and 0.67 (S = maximum stress/static ultimate). Failure analyses of the fatigue damage are conducted utilizing ultrasonic 'C' scan techniques.

Pipes, R. B.↗

NASA NTRS1977

Fatigue of notched fiber composite laminates - Analytical and experimental evaluation

Axial cracking in the load direction and transverse cracking across notched boron/epoxy laminate specimens subjected to tension/tension fatigue loading are studied both theoretically and experimentally. The fatigue analysis, which allows for the computation of residual strength and the determination of the preferred mode of crack propagation, is reviewed; static and fatigue data for boron/epoxy lamina are investigated with the aim of characterizing fatigue growth and residual strength as a function of the number of load cycles. It is suggested that correlation between the theory and the experiment may be limited by lack of a capability to predict the growth of delaminations.

Kulkarni, S. V.↗

NASA NTRS1978

Load-displacement measurement and work determination in three-point bend tests of notched or precracked specimens

Suggestions for testing of notched or cracked three-point bend specimens are presented that (1) correct displacement measurement errors resulting from misalignment between the load applicator and specimen; (2) account for coincidental strains not associated with the work of crack extension; (3) simplify record analysis and processing; and (4) extend displacement gage range without sacrifice of sensitivity or accuracy. These testing details are particularly applicable to procedures in which the crack extension force J(I) is determined from the work done on the specimen.

Buzzard, R. J.↗

NASA NTRS1977

Notched and unnotched fatigue behavior of angle-ply graphite/epoxy composites

The axial fatigue behavior of both notched and unnotched graphite/epoxy composites has been studied as part of a continuing research investigation. In unnotched studies, conducted on an AS/3501 laminate, S-N curves were determined for various stress ratios R using simply supported test specimens. Specimens were fatigue tested up to 5 x 10 to the 6th cycles. Apparent fatigue limits in tension-tension and compression-compression cycling occurred at about 60 percent of the respective static strengths. The overall results were expressed in the form of a constant life diagram (that is, a Goodman diagram) showing the relationship between mean stress and stress amplitude. The diagram shows a linear relationship and illustrates a skew-symmetry in fatigue life caused by the relatively low compressive strength of the unrestrained test specimens used. In effect, a maximum in stress amplitude occurs at a positive value of the mean stress.

Ramani, S. V.↗

NASA NTRS1979

Experimental and analytical study of fatigue damage in notched graphite/epoxy laminates

Both tension and compression fatigue behaviors were investigated in four notched graphite/epoxy laminates. After fatigue loading, specimens were examined for damage type and location using visual inspection, light microscopy, scanning electron microscopy, ultrasonic C-scans, and X-radiography. Delamination and ply cracking were found to be the dominant types of fatigue damage. In general, ply cracks did not propagate into adjacent plies of differing fiber orientation. To help understand the varied fatigue observations, the interlaminar stress distribution was calculated with finite element analysis for the regions around the hole and along the straight free edge. Comparison of observed delamination locations with the calculated stresses indicated that both interlaminar shear and peel stresses must be considered when predicting delamination. The effects of the fatigue cycling on residual strength and stiffness were measured for some specimens of each laminate type. Fatigue loading generally caused only small stiffness losses. In all cases, residual strengths were greater than or equal to the virgin strengths.

Whitcomb, J. D.↗

NASA NTRS1979

A structure for digital notch filters

Narrow-band digital notch filters have their poles near the unit circle. As the sampling rate is increased, the poles move towards Z = +1. Implementing such filters requires long registers to overcome the sensitivity and roundoff errors. A filter structure based on digital incremental computers is proposed which has low sensitivity and round-off errors, and simple hardware implementation. The filter structure can be directly used on differentially pulse-code modulated signals. Hardware multipliers are not required as the poles approach z = +1, and excellent results can be obtained using multipliers with very short word lengths, or with small size read-only memories.

Abu-El-haija, A. I.↗

NASA NTRS1980

Finite element stress analysis of a notched coupon specimen for in-plane shear behaviour of composites

The results of a linear elastic, plane stress finite element investigation of the stress distribution in a double V-notched coupon specimen are presented for an isotropic material (steel) and five graphite/polyimide laminates: (0), (90), (0/90)s, (plus or minus 45)s and (0/90/plus or minus 45)s. Stress contours, stress profiles, and stress concentration factors are presented for specimens loaded through rigid fixtures. It is shown that the finite element analysis predicts a region of essentially uniform pure shear in the central portion of the specimen for all laminates considered. Stress concentrations vary considerably with laminate configuration. The influences of elastic fixtures and thermal stresses on the stress distribution in (0) laminates are also investigated. The (0) laminate is predicted to exhibit maximum pure shear in the center of the test section for both rigid and elastic fixtures. It is concluded that the specimen is a practicable candidate for use as a composite shear specimen.

Herakovich, C. T.↗

NASA NTRS1981

Fracture toughness of brittle materials determined with chevron notch specimens

Short bar, short rod, and four-point-bend chevron-notch specimens were used to determine the plane strain fracture toughness of hot-pressed silicon nitride and sintered aluminum oxide brittle ceramics. The unique advantages of this specimen type are: (1) the production of a sharp natural crack during the early stage of test loading, so that no precracking is required, and (2) the load passes through a maximum at a constant, material-independent crack length-to-width ratio for a specific geometry, so that no post-test crack measurement is required. The plane strain fracture toughness is proportional to the maximum test load and functions of the specimen geometry and elastic compliance. Although results obtained for silicon nitride are in good mutual agreement and relatively free of geometry and size effects, aluminum oxide results were affected in both these respects by the rising crack growth resistance curve of the material.

Shannon, J. L., Jr.↗

NASA NTRS1981

Experimental and analytical study of fatigue damage in notched graphite/epoxy laminates

Fatigue damage development in notched graphite/epoxy laminates is investigated in both compression and tension, with tested specimens being examined for damage type and location using light microscopy, scanning electron microscopy, ultrasonic C-scans, and X-radiography. Delamination and ply cracking were found to be the dominant types of fatigue damage. Comparison of observed delamination locations with finite element calculations indicates that both interlaminar shear and peel stresses must be considered when predicting delamination. Fatigue loading generally caused only small stiffness losses, and residual strengths were in all cases greater than, or equal to, the virgin strengths.

Whitcomb, J. D.↗

NASA NTRS1983

Three-dimensional analysis of chevron-notched specimens by boundary integral method

The chevron-notched short bar and short rod specimens was analyzed by the boundary integral equations method. This method makes use of boundary surface elements in obtaining the solution. The boundary integral models were composed of linear triangular and rectangular surface segments. Results were obtained for two specimens with width to thickness ratios of 1.45 and 2.00 and for different crack length to width ratios ranging from 0.4 to 0.7. Crack opening displacement and stress intensity factors determined from displacement calculations along the crack front and compliance calculations were compared with experimental values and with finite element analysis.

Mendelson, A.↗

NASA NTRS1984

Dynamic stress analysis of smooth and notched fiber composite flexural specimens

A detailed analysis of the dynamic stress field in smooth and notched fiber composite (Charpy-type) specimens is reported in this paper. The analysis is performed with the aid of the direct transient response analysis solution sequence of MSC/NASTRAN. Three unidirectional composites were chosen for the study. They are S-Glass/Epoxy, Kevlar/Epoxy and T-300/Epoxy composite systems. The specimens are subjected to an impact load which is modeled as a triangular impulse with a maximum of 2000 lb and a duration of 1 ms. The results are compared with those of static analysis of the specimens subjected to a peak load of 2000 lb. For the geometry and type of materials studied, the static analysis results gave close conservative estimates for the dynamic stresses. Another interesting inference from the study is that the impact induced effects are felt by S-Glass/Epoxy specimens sooner than Kevlar/Epoxy or T-300/Epoxy specimens.

Murthy, P. L. N.↗