Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Fabrication of advanced electrochemical energy materials using sol-gel processing techniques

Advanced materials play an important role in electrochemical energy devices such as batteries, fuel cells, and electrochemical capacitors. They are being used as both electrodes and electrolytes. Sol-gel processing is a versatile solution technique used in fabrication of ceramic materials with tailored stoichiometry, microstructure, and properties. The application of sol-gel processing in the fabrication of advanced electrochemical energy materials will be presented. The potentials of sol-gel derived materials for electrochemical energy applications will be discussed along with some examples of successful applications. Sol-gel derived metal oxide electrode materials such as V2O5 cathodes have been demonstrated in solid-slate thin film batteries; solid electrolytes materials such as beta-alumina for advanced secondary batteries had been prepared by the sol-gel technique long time ago; and high surface area transition metal compounds for capacitive energy storage applications can also be synthesized with this method.

Chu, C. T.↗
NASA NTRS2002

Efficient Reformulation of the Thermoelastic Higher-order Theory for Fgms

Functionally graded materials (FGMs) are characterized by spatially variable microstructures which are introduced to satisfy given performance requirements. The microstructural gradation gives rise to continuously or discretely changing material properties which complicate FGM analysis. Various techniques have been developed during the past several decades for analyzing traditional composites and many of these have been adapted for the analysis of FGMs. Most of the available techniques use the so-called uncoupled approach in order to analyze graded structures. These techniques ignore the effect of microstructural gradation by employing specific spatial material property variations that are either assumed or obtained by local homogenization. The higher-order theory for functionally graded materials (HOTFGM) is a coupled approach developed by Aboudi et al. (1999) which takes the effect of microstructural gradation into consideration and does not ignore the local-global interaction of the spatially variable inclusion phase(s). Despite its demonstrated utility, however, the original formulation of the higher-order theory is computationally intensive. Herein, an efficient reformulation of the original higher-order theory for two-dimensional elastic problems is developed and validated. The use of the local-global conductivity and local-global stiffness matrix approach is made in order to reduce the number of equations involved. In this approach, surface-averaged quantities are the primary variables which replace volume-averaged quantities employed in the original formulation. The reformulation decreases the size of the global conductivity and stiffness matrices by approximately sixty percent. Various thermal, mechanical, and combined thermomechanical problems are analyzed in order to validate the accuracy of the reformulated theory through comparison with analytical and finite-element solutions. The presented results illustrate the efficiency of the reformulation and its advantages in analyzing functionally graded materials.

Bansal, Yogesh↗
NASA NTRS2012

Correlation of Fracture Behavior With Microstructure in Friction Stir Welded, and Spin Formed AI-Li 2195 Domes

Single-piece, spin-formed domes manufactured from friction stir welded (FSW) plates of Al-Li alloy 2195 have the potential to reduce the cost of fabricating cryogenic propellant tanks. Mechanical properties in the completed domes can be related directly to the final material condition and the microstructures developed. However, these new fabrication techniques have resulted in unexpected material challenges, such as abnormal grain growth in the weld nugget and the propensity for fracture in the adjacent thermo-mechanically affected zone (TMAZ). In this study, the microstructure and texture transformations within the TMAZ are related to fracture location in the vicinity of the weldment. The texture variations in the TMAZ are caused primarily by the varying amounts of shear deformation introduced during the FSW process. Grain morphology and microtexture characteristics are examined as a function of location in the TMAZ via electron backscatter diffraction (EBSD). A strong correlation between fracture location and the presence of texture banding in the TMAZ is observed. The fracture path tends to follow a distinct region of low Taylor Factor (TF) grains.

Tayon, Wesley A.↗
NASA NTRS1998

Semiconductors: In Situ Processing of Photovoltaic Devices

Current proposals for developing an extended human presence on the Moon and Mars increasingly consider the processing of nonterrestrial materials essential for keeping the Earth launch burden reasonable. Utilization of in situ resources for construction of lunar and Mars bases will initially require assessment of resource availability followed by the development of economically acceptable and technically feasible extraction processes. In regard to materials processing and fabrication, the lower gravity level on the Moon (0.125 g) and Mars (0.367 g) will dramatically change the presently accepted hierarchy of materials in terms of specific properties, a factor that must be understood and exploited. Furthermore, significant changes are expected in the behavior of liquid materials during processing. In casting, for example, mold filling and associated solidification processes have to be reevaluated. Finally, microstructural development, and therefore material properties, presently being documented through ongoing research in microgravity science and applications, need to be understood and scaled to the reduced gravity environments.

Curreri, Peter A.↗
NASA NTRS1999

In-Situ Production of Solar Power Systems for Exploration

Current proposals for developing an extended human presence, beyond space stations, on the Moon and Mars increasingly consider the processing of non-terrestrial materials essential for keeping the Earth launch burden reasonable. Utilization of in-situ resources for construction of lunar and Mars bases will initially require assessment of resource availability followed by the development of economically acceptable and technically feasible extractive processes. In regard to materials processing and fabrication the lower gravity level on the Moon (0.125 g) and Mars (0.367 g) will dramatically change the presently accepted hierarchy of materials in terms of specific properties, a factor which must be understood and exploited. Furthermore, significant changes are expected in the behavior of liquid materials during processing. In casting, for example, mold filling and associated solidification processes have to be reevaluated. Finally microstructural development and therefore material properties, presently being documented through on-going research in microgravity science and applications, needs to be understood and scaled to the reduced gravity environments. One of the most important elements of a human planetary base is power production. Lunar samples and geophysical measurements returned by the Apollo missions provide detailed data on the composition and physical characteristics of the lunar materials and environment. Based on this knowledge and extrapolations of terrestrial industrial experience it is clear that several types of solar-to-electric converters can be manufactured on the Moon. It is conceivable that well over 90% of a solar-to- electric power system could be made from lunar materials. Production and utilization of photovoltaic devices for solar energy production on Earth is primarily driven by the market economy. On Earth a production plant for photovoltaic devices is intimately linked to the planets massive industrial base. A selection of off the shelf refined materials are available as well as cheap fast transportation on demand. The processes takes place (except for the few seconds reprieve in shot towers etc.) under one gravity, with solar radiation significantly modulated by weather, and under conditions where one atmosphere is free and high vacuum is cumbersome and expensive. Off Earth, on lunar or Mars bases, the cost of photovoltaic power is driven by transport costs - Earth launch, deep space transport, landing on the planetary surface. Thus there is a premium for processes that are materials self-sufficient or for closed loop in-situ processes. The lack of differentiated ores on the Moon, and lack of explored minerals on Mars and interplanetary space give a premium to universal/non-ore-specific mineral extractive processes. Initially a semiconductor/photovoltaic production facility will build on no conveniently located industrial base, further increasing the premium on closed loop self sufficient processes.

Curreri, Peter A.↗
NASA NTRS2000

Micromechanical Characterization and Texture Analysis of Direct Cast Titanium Alloys Strips

This research was conducted to determine a post-processing technique to optimize mechanical and material properties of a number of Titanium based alloys and aluminides processed via Melt Overflow Solidification Technique (MORST). This technique was developed by NASA for the development of thin sheet titanium and titanium aluminides used in high temperature applications. The materials investigated in this study included conventional titanium alloy strips and foils, Ti-1100, Ti-24Al-11Nb (Alpha-2), and Ti-48Al-2Ta (Gamma). The methodology used included micro-characterization, heat-treatment, mechanical processing and mechanical testing. Characterization techniques included optical, electron microscopy, and x-ray texture analysis. The processing included heat-treatment and mechanical deformation through cold rolling. The initial as-cast materials were evaluated for their microstructure and mechanical properties. Different heat-treatment and rolling steps were chosen to process these materials. The properties were evaluated further and a processing relationship was established in order to obtain an optimum processing condition. The results showed that the as-cast material exhibited a Widmanstatten (fine grain) microstructure that developed into a microstructure with larger grains through processing steps. The texture intensity showed little change for all processing performed in this investigation.

Source record↗
NASA NTRSDate not supplied

Computational Investigation of Oxidative Etch Pitting in FiberForm and Its Impact on Material Properties

Oxidation-driven carbon erosion does not occur uniformly but rather through the development of localized etch pits at active surface sites. These active sites form due to atomic defects on the carbon surface, making them significantly more reactive than the surrounding, non-defective areas. As a result, these sites are the first to react during ablation, leading to their removal. This process creates new defects in neighboring atoms, increasing their reactivity and causing localized carbon removal around these active sites. In this way, the highly reactive defective areas serve as nucleation points for the formation and growth of etch pits, which can have adverse effects on structural integrity of FiberForm. To better understand how these etch pits impact the material properties of carbon fiber microstructures, we have developed a new capability within the direct simulation Monte Carlo (DSMC) framework to capture the etch pit formation process. This capability, integrated into the DSMC code SPARTA (Stochastic Parallel Rarefied-gas Time-accurate Analyzer), models material removal in the presence of active sites, leading to the formation of etch pits. The current work focuses on studying the effects of these etch pits on the material properties of FiberForm, a widely used base material in thermal protection systems (TPS). The microstructure of virgin FiberForm, obtained via X-ray microtomography, is imported into SPARTA to generate the ablated geometries with etch pits. These modified microstructures are then analyzed using the Porous Microstructure Analysis (PuMA) software to compute various material properties, including elasticity, thermal conductivity, and permeability. We investigate the variation of these properties due to the complex surface topology changes caused by etch pit formation. Additionally, we compare the effects of pitting with the conventional model of shrinking fibers, traditionally used to simulate the ablation of carbon structures. Significant differences emerge between the two approaches. Consequently, this physically realistic model of material removal through etch pit formation offers improved accuracy in predicting the degradation of carbon-based TPS during oxidation. It also provides insights into other mechanisms, such as spallation, where chunks of material are removed into the flow due to etch pit growth. Ultimately, this model enhances our understanding of failure modes in these materials during ablation.

PuMA↗
NASA NTRS2024

Direct Ink Write 3D Printing of Fully Dense and Functionally Graded Liquid Metal Elastomer Foams

Liquid metal (LM) elastomer composites offer promising potential in soft robotics, wearable electronics, and human-machine interfaces. Direct ink write (DIW) 3D printing offers a versatile manufacturing technique capable of precise control over LM microstructures, yet challenges such as interfilament void formation in multilayer structures impact material performance. Here, a DIW strategy is introduced to control both LM microstructure and material architecture. Investigating three key process parameters–nozzle height, extrusion rate, and nondimensionalized nozzle velocity–it is found that nozzle height and velocity predominantly influence filament geometry. The nozzle height primarily dictates the aspect ratio of the filament and the formation of voids. A threshold print height based on filament geometry is identified; below the height, significant surface roughness occurs, and above the ink fractures, which facilitates the creation of porous structures with tunable stiffness and programmable LM microstructure. These porous architectures exhibit reduced density and enhanced thermal conductivity compared to cast samples. When used as a dielectric in a soft capacitive sensor, they display high sensitivity (gauge factor = 9.0), as permittivity increases with compressive strain. These results demonstrate the capability to simultaneously manipulate LM microstructure and geometric architecture in LM elastomer composites through precise control of print parameters, while maintaining geometric fidelity in the printed design.

Spencer Pak↗
NASA NTRS1990

Microstructure and magnetization of doped Y-Ba-Ca-O materials prepared by melt quench and post annealing method

Y-Ba-Cu-O bulk materials prepared using the melt quench and post annealing method were shown to have very high maximum as well as remanent magnetization. Studies were carried out on materials prepared using this method which deviate from the Y:Ba:Cu = 1:2:3 stoichiometry. In one series of materials, only the stoichiometry was changed, in particular by introducing an excess of yttrium. In other cases, dopants including several rare earths were introduced. Effects of variations in composition on microstructure and phase evolution are discussed, as well as effects on the magnetic susceptibility and on the magnetization. The results show that doped materials can exhibit improvements in magnetic properties. Furthermore, the use of dopants sheds light on the role of defect sites in flux pinning.

Hojaji, H.↗
NASA NTRS2009

Failure Analysis of Main Flame Deflector Nelson Studs

NASA Structures engineers submitted two Nelson refractory studs from the main flame deflector at Launch Complex (LC) 39 A for analysis when they were observed to be missing a significant amount of material after launch. The damaged stud and an unused comparative stud were analyzed by macroscopic and microscopic examination along with metallographic evaluation of the microstructure. The stud lost material due to a combination of erosion and corrosion. Plain carbon steel readily forms an oxide layer in the coastal launch environment at Kennedy Space Center. The blast during a launch removes this brittle oxide layer, which then forms again post-launch, thereby further removing material. No indications of melting were observed.

Long, Victoria↗
NASA NTRSDate not supplied

Particle-Based Fiber Models of Woven Materials for Earth Entry Thermal Protection

Applications requiring materials with layer-to-layer strength, from basketry to thermal protection systems, use interlaced, three-dimensional woven materials. NASA is developing and deploying woven material heat shields for missions, including Artemis I (3D-MAT for compression pads) and potentially Mars Sample Return - Earth Entry System. These materials are complex, hierarchical and must protect from extreme environments and phenomena, such as deformation, impact and high-enthalpy heating. Woven material performance depends on microstructure, damage and weave geometry. Therefore, fiber-specific models are needed to simulate fiber contacts within the weave hierarchical geometry (fiber to tow to yarn to weave) and the inherent directionality of fibers. Explicit fiber models can simulate how weave microstructure evolution affects thermal and mechanical properties. We parameterize a discrete element bonded particle models (DEM-BPM) of fibers to capture thermal and mechanical behavior within and between fibers, with bonded and contact forces, respectively. We study the proportion of heat transfer and stress via the contact network, fiber bonds and the weave geometry, for example, with respect to yarn warp-weft identity (whether it interlaces weave layers). Our results demonstrate the importance of explicit fiber modeling for connecting microstructure with thermal and mechanical properties.

woven material↗
NASA NTRSDate not supplied

Particle-Based Fiber Models of Woven Materials for Earth Entry Thermal Protection

Applications requiring materials with layer-to-layer strength, from basketry to thermal protection systems, use interlaced, three-dimensional woven materials. NASA is developing and deploying woven material heat shields for missions, including Artemis I (3D-MAT for compression pads) and potentially Mars Sample Return - Earth Entry System. These materials are complex, hierarchical and must protect from extreme environments and phenomena, such as deformation, impact and high-enthalpy heating. Woven material performance depends on microstructure, damage and weave geometry. Therefore, fiber-specific models are needed to simulate fiber contacts within the weave hierarchical geometry (fiber to tow to yarn to weave) and the inherent directionality of fibers. Explicit fiber models can simulate how weave microstructure evolution affects thermal and mechanical properties. We parameterize a discrete element bonded particle models (DEM-BPM) of fibers to capture thermal and mechanical behavior within and between fibers, with bonded and contact forces, respectively. We study the proportion of heat transfer and stress via the contact network, fiber bonds and the weave geometry, for example, with respect to yarn warp-weft identity (whether it interlaces weave layers). Our results demonstrate the importance of explicit fiber modeling for connecting microstructure with thermal and mechanical properties.

woven material↗
NASA NTRS1997

Microstructure and Mechanical Properties of Vacuum Plasma Sprayed Cu-8Cr-4Nb

This paper compares the tensile properties of Cu-8Cr-4Nb material produced by VPS to material previously produced by extrusion. The microstructure of the VPS material is also presented. The combustion chamber liner of rocket motors represents an extreme materials application. The liner hot wall is exposed to a 2760 C (5000 F) flame while the cold side is exposed to cryogenic hydrogen liquid. Materials for use in the combustion chamber liner require a combination of high temperature strength, creep resistance, and low cycle fatigue resistance along with high thermal conductivity. The hot side is also subject to localized cycles between reducing and oxidizing environments that degrade the liner by a process called blanching. A new Cu-8 at.% Cr-4 at% Nb (Cu-8Cr-4Nb) alloy has been developed at NASA Lewis Research Center as a replacement for the currently used alloy, NARloy-z (Cu-3 wt.% Ag-0.5 wt.% Zr). The alloy is strengthened by a fine dispersion of Cr2Nb particles. The alloy has better mechanical properties than NARloy-Z while retaining most of the thermal conductivity of pure copper. The alloy has been successfully consolidated by extrusion and hot isostatic pressing (HIPing). However, vacuum plasma spraying (VPS) offers several advantages over prior consolidation methods. VPS can produce a near net shape piece with the profile of the liner. In addition, oxidation resistant and thermal barrier coatings can be incorporated as an integral part of the liner hot wall during the VPS deposition. The low oxygen VPS Cu-8Cr-4Nb exhibits a higher strength than Cu-8Cr-4Nb produced by extrusion at elevated temperatures and a comparable strength at room temperature. Moduli and ductility were not significantly different. However, the ability to produce parts to near-net shape and maintain the good elevated temperature tensile properties of the extruded Cu-8Cr-4Nb makes VPS an attractive processing method for fabricating rocket engine combustion liners.

Holmes, Richard↗
NASA NTRS1975

Fused silica reflecting heat shields for outer planet entry probes

The development of slip-cast fused silica is discussed as a heat shield designed to meet the needs of outer-planet entry probes. The distinguishing feature of silica is its ability to reflect the radiation imposed by planetary-entry environments. This reflectivity is particularly sensitive to degradation by the presence of trace amounts of contaminants introduced by the starting materials or by processing. The microstructure of a silica configuration also significantly influences the reflectivity and other thermomechanical properties. The processing techniques attendant on controlling microstructure while maintaining purity are discussed. The selection of a starting material of essential purity precludes the use of purified natural quartz and requires the use of synthetic fused silica. The silica is characterized in a limited combined heating test environment. The surface mass loss is controlled by liquid runoff from a relatively low-temperature melt layer; the reflectance is basically maintained and the material achieves a surprisingly high heat of ablation.

Congdon, W. M.↗
NASA NTRS1985

Impact wear of iron rich superalloys

The impact-sliding wear resistance of chill cast and aligned eutectic Fe-base superalloys against M42 and 17-4 PH steel counterface materials is examined. The aligned material tests were run with carbide fibers perpendicular to the counterface contact surface and the characterization focused on fracture processes as observed in the subsurface microstructure of the worn materials. Metallographic analyses were performed on specimens exposed to various numbers of repetitive impact load cycles, and for comparison, two other aligned composites were tested with the same fiber orientation under identical test conditions against hardened M42 tool steel. A strong improvement was found in wear resistance of an aligned eutectic structure as compared to the corresponding randomized chill cast structure. Experiments with the softer 17-4 counterface were characterized by transfer onto the Fe-base superalloy, and the cracks formed were oriented transverse to the relative sliding direction and occurred in a periodic fashion. Observations in subsurface regions of the worn materials indicated crack intergranularity with an occasional transgranular fracture of the M7C3 carbide phase.

Wayne, S. F.↗
NASA NTRS2015

Investigation of Micro-Scale Architectural Effects on Damage of Composites

This paper presents a three-dimensional, energy based, anisotropic, stiffness reduction, progressive damage model for composite materials and composite material constituents. The model has been implemented as a user-defined constitutive model within the Abaqus finite element software package and applied to simulate the nonlinear behavior of a damaging epoxy matrix within a unidirectional composite material. Three different composite microstructures were considered as finite element repeating unit cells, with appropriate periodicity conditions applied at the boundaries. Results representing predicted transverse tensile, longitudinal shear, and transverse shear stress-strain curves are presented, along with plots of the local fields indicating the damage progression within the microstructure. It is demonstrated that the damage model functions appropriately at the matrix scale, enabling localization of the damage to simulate failure of the composite material. The influence of the repeating unit cell geometry and the effect of the directionality of the applied loading are investigated and discussed.

damage↗
NASA NTRS1999

Proceedings of the Second Annual Symposium for Nondestructive Evaluation of Bond Strength

Ultrasonics, microwaves, optically stimulated electron emission (OSEE), and computational chemistry approaches have shown relevance to bond strength determination. Nonlinear ultrasonic nondestructive evaluation methods, however, have shown the most effectiveness over other methods on adhesive bond analysis. Correlation to changes in higher order material properties due to microstructural changes using nonlinear ultrasonics has been shown related to bond strength. Nonlinear ultrasonic energy is an order of magnitude more sensitive than linear ultrasound to these material parameter changes and to acoustic velocity changes caused by the acoustoelastic effect when a bond is prestressed. Signal correlations between non-linear ultrasonic measurements and initialization of bond failures have been measured. This paper reviews bond strength research efforts presented by university and industry experts at the Second Annual Symposium for Nondestructive Evaluation of Bond Strength organized by the NDE Sciences Branch at NASA Langley in November 1998.

Roberts, Mark J.↗
NASA NTRS2009

A Method for Combining Experimentation and Molecular Dynamics Simulation to Improve Cohesive Zone Models for Metallic Microstructures

Fracture processes within a material begin at the nanometer length scale at which the formation, propagation, and interaction of fundamental damage mechanisms occur. Physics-based modeling of these atomic processes quickly becomes computationally intractable as the system size increases. Thus, a multiscale modeling method, based on the aggregation of fundamental damage processes occurring at the nanoscale within a cohesive zone model, is under development and will enable computationally feasible and physically meaningful microscale fracture simulation in polycrystalline metals. This method employs atomistic simulation to provide an optimization loop with an initial prediction of a cohesive zone model (CZM). This initial CZM is then applied at the crack front region within a finite element model. The optimization procedure iterates upon the CZM until the finite element model acceptably reproduces the near-crack-front displacement fields obtained from experimental observation. With this approach, a comparison can be made between the original CZM predicted by atomistic simulation and the converged CZM that is based on experimental observation. Comparison of the two CZMs gives insight into how atomistic simulation scales.

Hochhalter, J. D.↗