Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LIME”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Enhanced pozzolanic reactivity in hydrogen-form zeolites as supplementary cementitious materials

Pozzolans rich in silica and alumina react with lime to form cementing compounds and are incorporated into portland cement as supplementary cementitious materials (SCMs). However, pozzolanic reactions progress slower than portland cement hydration, limiting their use in modern construction due to insufficient early-age strength. Hence, alternative SCMs that enable faster pozzolanic reactions are necessary including synthetic zeolites, which have high surface areas and compositional purity that indicate the possibility of rapid pozzolanic reactivity. Synthetic zeolites with varying cation composition (Na-zeolite, H-zeolite), SiO 2 /Al 2 O 3 ratio, and framework type were evaluated for pozzolanic reactivity via Ca(OH) 2 consumption using ion exchange and in-situ X-ray diffraction experiments. Na-zeolites exhibited limited exchange reactions with KOH and Ca(OH) 2 due to the occupancy of acid sites by Na + and hydroxyl groups. Meanwhile, H-zeolites readily adsorbed K + and Ca 2+ from a hydroxide solution by exchanging cations with H + at Brønsted acid sites or cation adsorption at vacant acid sites. By adsorbing cations, the H-zeolite reduced the pH and increased Ca 2+ solubility to promote pozzolanic reactions in a system where Ca(OH) 2 dissolution/diffusion was a rate limiting factor. High H-zeolite reactivity resulted in 0.8 g of Ca(OH) 2 consumed per 1 g of zeolites after 16 h of reaction versus 0.4 g of Ca(OH) 2 consumed per 1 g of Na-zeolite. The H-zeolite modulated the pore fluid alkalinity and created a low-density amorphous silicate phase via mechanisms analogous to two-step C-S-H nucleation experiments. Finally, controlling these reaction mechanisms is key to developing next generation pozzolanic cementitious systems with comparable hydration rates to portland cement.

36 MATERIALS SCIENCE↗

Synthesis of belite cement clinker of high hydraulic reactivity

This study is concerned with the increase of the cooling rate of belite clinker, by using the water quenching for the chemical stabilization of reactive belite, which improves the hydraulic properties of this clinker. The addition of adequate mineralizers, as NaF and Fe{sub 2}O{sub 3}, contributes to the improvement of the clinker properties obtained at low burning temperature. X-ray fluorescence spectroscopy, X-ray diffraction analysis and optical microscopy were used to determine the chemical and mineralogical compositions of this clinker. The samples were analyzed by means of a scanning electronic microscope connected with an energy-dispersive X-ray spectrometer to detect the composition of the belite phase and its morphology. Physical and mechanical properties of this clinker cement were determined. The results show that the belite clinker obtained at 1150 {sup o}C, with lime saturation factor 0.67, is characterized by a great hydraulic reactivity, similar to that of the ordinary alite clinker. The addition of 2% of NaF and the water quenching improved the chemical, mineralogical and structural properties, while improving the cement hydraulic properties.

36 MATERIALS SCIENCE↗

Incorporation of titanium dioxide nanoparticles in mortars - Influence of microstructure in the hardened state properties and photocatalytic activity

The environmental pollution in urban areas is one of the causes for poor indoor air quality in buildings, particularly in suburban areas. The development of photocatalytic construction materials can contribute to clean the air and improve sustainability levels. Previous studies have focused mainly in cement and concrete materials, disregarding the potential application in historic buildings. In this work, a photocatalytic additive (titanium dioxide) was added to mortars prepared with aerial lime, cement and gypsum binders. The main goal was to study the way that microstructural changes affect the photocatalytic efficiency. The photocatalytic activity was determined using a reactor developed to assess the degradation rate with a common urban pollutant, NO{sub x}. The laboratory results show that all the compositions tested exhibited high photocatalytic efficiency. It was demonstrated that photocatalytic mortars can be applied in new and old buildings, because the nanoadditives do not compromise the mortar hardened state properties.

36 MATERIALS SCIENCE↗

Chemical acceleration of a neutral granulated blast-furnace slag activated by sodium carbonate

This paper presents results of a study on chemical acceleration of a neutral granulated blast-furnace slag activated using sodium carbonate. As strength development of alkali-activated slag cements containing neutral GBFS and sodium carbonate as activator at room temperature is known to be slow, three accelerators were investigated: sodium hydroxide, ordinary Portland cement and a combination of silica fume and slaked lime. In all cements, the main hydration product is C–(A)–S–H, but its structure varies between tobermorite and riversideite depending on the accelerator used. Calcite and gaylussite are present in all systems and they were formed due to either cation exchange reaction between the slag and the activator, or carbonation. With accelerators, compressive strength up to 15 MPa can be achieved within 24 h in comparison to 2.5 MPa after 48 h for a mix without an accelerator.

36 MATERIALS SCIENCE↗

Direct three-dimensional observation of the microstructure and chemistry of C{sub 3}S hydration

Disagreements about the mechanisms of cement hydration remain despite the fact that portland cement has been studied extensively for over 100 years. One reason for this is that direct observation of the change in microstructure and chemistry are challenging for many experimental techniques. This paper presents results from synchrotron nano X-ray tomography and fluorescence imaging. The data show unprecedented direct observations of small collections of C{sub 3}S particles before and after different periods of hydration in 15 mmol/L lime solution. X-ray absorption contrast is used to make three dimensional maps of the changes of these materials with time. The chemical compositions of hydration products are then identified with X-ray fluorescence mapping and scanning electron microscopy. These experiments are used to provide insight into the rate and morphology of the microstructure formation.

36 MATERIALS SCIENCE↗

Carbonation, strength development, and characterization of calcined limestone as a potential construction material

The emergence of the modern Portland cement has led to the downfall of lime as a construction material. Consequentially, its use has been limited to repair and restoration of historical buildings. Yet, its lower calcination temperature (~950 °C) and the ability to gain strength through carbonation implies its potential as a sustainable alternative to cement. In this study, calcined limestone was studied concerning its carbonation and strength development. Superplasticizer, raw limestone, and different carbonation regimes were explored as techniques to improve the composite strength development, a shortfall that hinders its re-adoption. The results indicated that the raw limestone as a partial replacement of the calcined limestone significantly improved the carbonation degree and mechanical properties. The average compressive strength reached 20 MPa under 20% CO{sub 2} due to the formation of an interconnected network of calcite as the dominant carbonation product. Supercritical CO{sub 2}, in contrast, formed disjoint particles or agglomerates of carbonates.

36 MATERIALS SCIENCE↗

Comprehensive characterization of CIGS absorber layers grown by one-step sputtering process

We have demonstrated that the use of a one-step sputtering process allowed for the fabrication of copper indium gallium diselenide (CIGS) thin films by RF magnetron sputtering without an additional selenization process. The CIGS thin films deposited at different substrate temperatures were synthesized on soda-lime glass (SLG) substrates using a single quaternary CIGS target. The film composition ratios of ([Cu]/[In]+[Ga]), ([Ga]/[In]+[Ga]), and ([Se]/[Cu]+[In]+[Ga]) were almost consistent with those of the sputtering target. X-ray diffraction (XRD) and Raman results showed that the crystallinity of the CIGS thin films was gradually improved as substrate temperatures increased. Transmission electron microscopy (TEM) showed that the films grown at 600 degrees C have a columnar structure with the grain size of ~100 nm. In addition, for the CIGS films grown at 600 degrees C, TEM-EDX analysis revealed that the synchronized fluctuation of the Cu and Se signals was observed in the direction of the film depth, while the In and Ga signals were constant. As a result, the CIGS solar cell made using the film showed a degraded cell efficiency of 2.5%, which might be have been caused by not only Cu-rich and Se-poor compositions but the locally unstable composition in the CIGS films fabricated by one-step sputtering.

14 SOLAR ENERGY↗

An asymptotically compatible treatment of traction loading in linearly elastic peridynamic fracture

Meshfree discretizations of state-based peridynamic models are attractive due to their ability to naturally describe fracture of general materials. However, two factors conspire to prevent meshfree discretizations of state-based peridynamics from converging to corresponding local solutions as resolution is increased: quadrature error prevents an accurate prediction of bulk mechanics, and the lack of an explicit boundary representation presents challenges when applying traction loads. Herein, we develop a reformulation of the linear peridynamic solid (LPS) model to address these shortcomings, using improved meshfree quadrature, a reformulation of the nonlocal dilatation, and a consistent handling of the nonlocal traction condition to construct a model with rigorous accuracy guarantees. In particular, these improvements are designed to enforce discrete consistency in the presence of evolving fractures, whose a priori unknown location render consistent treatment difficult. In the absence of fracture, when a corresponding classical continuum mechanics model exists, our improvements provide asymptotically compatible convergence to corresponding local solutions, eliminating surface effects and issues with traction loading which have historically plagued peridynamic discretizations. When fracture occurs, our formulation automatically provides a sharp representation of the fracture surface by breaking bonds, avoiding the loss of mass. We provide rigorous error analysis and demonstrate convergence for a number of benchmarks, including manufactured solutions, free-surface, nonhomogeneous traction loading, and composite material problems. Finally, we validate simulations of brittle fracture against a recent experiment of dynamic crack branching in soda-lime glass, providing evidence that the scheme yields accurate predictions for practical engineering problems.

42 ENGINEERING↗

The evaluation of critical rare earth element (REE) enriched treatment solids from coal mine drainage passive treatment systems

Rare earth elements (REE; lanthanides and Y) are essential for the development of clean energy technologies. Global demand for REE is expected to increase sharply in the coming decades, especially for certain energy-critical REE (e.g., Y and Nd), spurring investigations into novel sources of REEs. Polluted mine drainage from eastern U.S. coalfields contains elevated concentrations of dissolved Fe, Al, and Mn and is also enriched in REE by up to three orders of magnitude over unpolluted groundwater. Mine drainage remediation systems, designed to precipitate dissolved metals, can sequester >90% of dissolved REE into the precipitated solids (treatment solids). These solids, landfilled at cost to treatment system operators, are a promising REE source. Passive treatment systems with diverse geochemical environments were sampled to determine REE mobility in these systems and REE concentrations in treatment solids. Passive treatment systems were found to produce middle and heavy REE-enriched solids, relative to the North American Shale Composite, with up to 1950 ppm REE and 55% energy-critical REE. SEM-EDS and synchrotron μ-XRF analysis demonstrate the association of REE with Mn-oxide coatings on limestone from a passive treatment system. Calculated concentration factors indicate that passive treatment systems using natural processes (e.g., drainable limestone beds and vertical flow ponds) concentrate REE into treatment solids approximately three times more effectively compared to active treatment systems using caustic chemical additions (e.g., lime). This study suggests that passive treatment systems effectively concentrate REE into treatment solids and these solids could be an alternative and more environmentally friendly source of REE compared to conventional mining on land or the seafloor. Results of this study can also aid in the design of treatment systems engineered to remove and concentrate critical REE which could provide a financial incentive to treat polluted mine water.

58 GEOSCIENCES↗

express: Extensible, high-level workflows for swifter ab initio materials modeling

In this work, we introduce an open-source Julia project, express, an extensible, lightweight, high-throughput, high-level workflow framework that aims to automate ab initio calculations for the materials science community. express is shipped with well-tested workflow templates, including structure optimization, equation of state (EOS) fitting, phonon spectrum (lattice dynamics) calculation, and thermodynamic property calculation in the framework of the quasi-harmonic approximation (QHA). It is designed to be highly modularized so that its components can be reused across various occasions, and customized workflows can be built on top of that. Users can also track the status of workflows in real-time, and rerun failed jobs thanks to the data lineage feature express provides. Finally, two working examples, i.e., all workflows applied to lime and akimotoite, are also presented in the code and this paper.

36 MATERIALS SCIENCE↗

Spectroscopic investigation of historical uranium glasses

Here, we present spectroscopic investigations of uranium in two historical glasses. A 1920's-1930's Art Deco (Bagley Carnival) green soda-lime-silica uranium glass bowl and a 1930's-1940's (Thomas Webb) yellow full lead crystal uranium glass vase were studied using optical absorption spectroscopy, XRF and SEM-EDX, X-band EPR and High- Energy Resolution Fluorescence-Detected (HERFD)-XANES. Uranium speciation may be different in the two glasses. Uranium occurs as uranyl groups (UO 2 2+ ) with minority reduced uranium species, mostly as U(V), more important in the Webb glass than in the Bagley glass. The differences between the two glasses arise from the fining procedure and result from the presence of other multivalent elements and differences in base glass composition. Electron Paramagnetic Resonance (EPR) spectra show the presence of an incipient signal close to g~2, partially annealed by heating to 550 °C, which we assign to a small concentration of radiation-induced defects caused by uranium decay. The presence of multivalent glass components in addition to U (As + Cu + Fe in the Bagley glass and Sb + Fe in the Webb glass) can trap the electron-hole pairs generated by the presence of uranium. This may explain the weakness of this signal in these glasses that anyway received a limited radiation dose since their fabrication. The low activity of these glasses, close to the background radiation, confirms that there is no danger to exhibiting them in museums.

36 MATERIALS SCIENCE↗

Cadmium retention and distribution in contaminated soil: effects and interactions of soil properties, contamination level, aging time and in situ immobilization agents

As soil cadmium (Cd) contamination becomes a serious concern and one of the significant environmental pollution issues all over the world, knowledge of the basic chemistry, origin, inputs, sources, quantity, chemical forms, reactions, as well as the fate and transport of Cd in different types of soil is crucial for better understanding Cd bioavailability, health risks and remedial options. This study aimed to increase the current knowledge on the complex interdependence between the factors affecting behavior, transport and fate of Cd in the soil and to test and compare the performance of the stabilization agents in different soil types. Soils demonstrated various sorption affinity and capacity for Cd accumulation, which proved to be positively correlated with soil pH and the cation exchange capacity (CEC). With increasing levels of contamination, sequential extraction analysis showed the highest increase of relative Cd amounts in the exchangeable fraction regardless of the soil properties, suggesting that added Cd is principally associated with the easily accessible and mobile fraction. For different initial Cd concentrations and soil types, Cd sorption reached the quasi-equilibrium within 24 h of contact. Prolonged aging (two months) influenced the natural stabilization of Cd in all types of soil, but only at low contamination level. The application of both, conventional (slaked lime Ca(OH) 2) and alternative phosphate-rich (annealed bovine bones B 400) amendments, resulted in Cd relocation and reduction of exchangeable Cd content. Although the effect was smaller when apatite amendment was utilized, observed re-distribution of Cd to more stable soil fractions is preferable for achieving long-term stabilization. Cd concentrations extracted in exchangeable and acid soluble fractions after the treatments of contaminated soil samples suggest that the practical applicability of in situ immobilization depends on the soil properties and the level of contamination, as well as that effect, should be monitored for the possible re-mobilization of Cd. © 2019 Elsevier Inc.

02 PETROLEUM↗

Rheological investigation of effect of high temperature on geothermal drilling fluids additives and lost circulation materials

High temperatures (HT) and the corrosive environment make the design of a geothermal drilling fluid a highly complex task. The presence of HT exacerbates the problems due to thermal degradation. Geothermal aquifers usually combine high-temperature and complex chemistry, making them highly corrosive. Although geothermal drilling fluids are exposed to thermal degradation, research of the effect on mud rheological properties in temperatures near or above 149°C (300°F) is limited. In this study, a High Pressure-High Temperature (HPHT) rheology setup was used to measure drilling fluids' properties up to 204.4°C (400°F). Rheological behavior of viscosity, density, lost circulation, and alkalinity control additives were analyzed at HT. It was found experimentally that Bentonite alone is thermally stable at HT. In contrast, Caustic Soda showed a tendency to gelate at temperatures above 93.3°C (200°F), adversely affecting mud rheology. Alkalinity control materials to replace Caustic Soda were evaluated. Among them, Lime presented the best thermal stability at 204.4°C with a range of variation of 0.0024 Pa.s (2.4 cP) on apparent viscosity after three consecutive tests. Besides, it was tested 11 different lost circulation materials (LCM) for understanding their rheological behavior at HT. Further, it was found that HT has less impact on fine granular materials rheological behavior with an average increase of 17.7% compared with the baseline. In contrast, flaky, fibrous, and coarse granular materials presented a more apparent impact in WBM rheology with a deviation of 166% compared with the baseline.

15 GEOTHERMAL ENERGY↗

Effects of micrometer-scale surface roughness on thermal infrared emittance spectra of silica glass

Surface roughness is known to decrease thermal infrared (TIR) absorption band intensity, but studies of the effect on geologically relevant samples are relatively limited. To determine the effect of surface roughness (with features smaller than ~2/3 of the wavelength) on TIR spectra, we investigated two glass compositions with prepared roughened surfaces: (1) high purity fused silica and (2) soda-lime glass (73 wt% SiO$_2$). We roughened the surfaces of the glasses by sandblasting and polishing with grit paper. The surfaces were characterized with scanning electron microscopy and stylus profilometry. We then analyzed the roughened glasses with TIR emittance spectroscopy. Micrometer-scale roughness causes a decrease in TIR absorption band intensity, relative to a specular surface. No significant changes in band shape or shifts in wavelength were detected. As roughness increases, empirical results show a logarithmic decrease in TIR absorption band intensity. The logarithmic trends of the two glass compositions are different; empirical roughness calibrations do not translate across different compositions. A linear, least-squares spectral deconvolution using two endmembers, specular and blackbody, predicts model spectra of roughened glass surfaces with relatively low error. This is of consequence to orbital TIR measurements of poorly constrained targets, such as the martian surface, because micrometer-scale roughness is adequately modeled by the addition of a blackbody spectrum to the deconvolution endmember matrix.

36 MATERIALS SCIENCE↗

Piperazine aerosol mitigation for post-combustion carbon capture

Amine loss as aerosol is still a challenge for reliable long-term operations in amine scrubbing units. While attempts have been made to understand, predict, and mitigate amine aerosol growth in the absorber, demonstration of the mitigation of piperazine (PZ) aerosol has not been published. This paper presents results from a comprehensive emission study using 5 m PZ. The focus of this work is not to validate growth mechanisms, but to provide data from which existing hypotheses can be analyzed. PZ aerosol at the water wash outlet was characterized by Fourier Transform Infrared Spectroscopy (FTIR) and an Electrical Low-Pressure Impactor (ELPI + ). Two mitigation strategies were successfully implemented during episodes of PZ aerosol emission. These episodes resulted from the presence of SO 3 in the flue gas due to periods of sub-optimal SO 3 removal upstream of the CO 2 capture facility. Four weeks of aerosol tests were also run with 0–6 ppm of SO 3 generated and injected into the flue gas to evaluate the resilience of the mitigation strategies. The first approach to aerosol emission mitigation was to remove aerosol nuclei present in the flue gas. The second approach was to run the absorber with flue gas containing varying SO 3 at conditions that accelerate aerosol nuclei growth and collection within the packing. SO 3 control via hydrated lime addition upstream of the absorber eliminated aerosol while higher lean solvent temperature in the absorber and a two-stage water wash configuration were tested to accelerate aerosol nuclei growth and collection. Increasing the lean solvent temperature by 11 °C and using a two-stage water wash resulted in 98% reduction of PZ emissions. Absorber performance at the elevated lean solvent temperature was sustained in the existing packing with solvent intercooling. PZ emissions were managed to less than 1 ppm for extended periods during the pilot plant campaign.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of Cu(In,Ga)Se 2 (CIGS) films with varying gallium ratios

Cu(In 1-x ,Ga x )Se 2 (CIGS) absorber layers were deposited on molybdenum (Mo) coated soda-lime glass substrates with varying Ga content (described as Ga/(In+Ga) ratios) with respect to depth. As the responsible mechanisms for the limitation of the performance of the CIGS solar cells with high Ga contents are not well understood, the goal of this work was to investigate different properties of CIGS absorber films with Ga/(In+Ga) ratios varied between 0.29 and 0.41 (as determined by X-ray florescence spectroscopy (XRF)) in order to better understand the role that the Ga content has on film quality. The Ga grading in the CIGS layer has the effect causing a higher bandgap toward the surface and Mo contact while the band gap in the middle of the CIGS layer is lower. Also, a wider and larger Ga/(In+Ga) grading dip located deeper in the CIGS absorber layers tend to produce larger grains in the regions of the films that have lower Ga/(In+Ga) ratios. It was found that surface roughness decreases from 51.2 nm to 41.0 nm with increasing Ga/(In+Ga) ratios. However, the surface roughness generally decreases if the Ga grading occurs deeper in the absorber layer.

14 SOLAR ENERGY↗