SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Some of the principal results obtained in three series of measurements of fluctuating surface pressures induced on externally blown flaps by jet impingment are presented. Large- and small-scale models and hot- and cold-flow tests are considered. The discussion sets forth scaling parameters and consistent features of the root-mean-square values and spectra of the loading. Implications of these results with regard to sonic fatigue are indicated.
Data and high speed movies were acquired on pressurized subcooled liquid nitrogen flowing radially inward through a 0.0076 cm gap. The stagnation pressure ranged from 0.7 to 4 MN/sq m. Steady radial inward choked flow appears equivalent to steady choked flow through axisymmetric nozzles. Transient choked flows through the radial gap are not uniform and the discharge pattern appears as nonuniform impinging jets. The critical mass flow rate data for the transient case appear different from those for the steady case. On the mass flow rate vs pressure map, the slope and separation of the isotherms appear to be less for transient than for steady radial choked flow.
General formulas are derived for determining gage averaging errors of strip-type heat flux meters used in the measurement of one-dimensional heat flux distributions. In addition, a correction procedure is presented which allows a better estimate for the true value of the local heat flux. As an example of the technique, the formulas are applied to the cases of heat transfer to air slot jets impinging on flat and concave surfaces. It is shown that for many practical problems, the use of very small heat flux gages is often unnecessary.
Systematic methods based on cross-correlation techniques are presented for experimental studies of near- and far-field noise characteristics of airflow-surface interaction problems. By cross-correlating any two of three-kinds of microphone measurements: one flush-mounted on the surface, one located in the near field, and one placed in the far field, far-field noise intensities and near-field acoustic energy fluxes can be determined. In both near and far fields, the noise characteristics due to the flow turbulence and surface fluctuating pressure contributions can be evaluated separately. Specific applications to the noise field generated by impinging jets, by surface blowing jets, and by turbulent flow over trailing edges are discussed.
The present study is based on Lighthill-Curle's theory of aerodynamic noise. Using a correlation approach and the image concept of Powell, the volume contribution of turbulent flow over a large surface is approximated by a surface contribution of pressure fluctuations. Far-field noise intensities are expressed in terms of the surface pressure fluctuations and surface impedance. Based on available experimental measurements, numerical examples are performed for noise radiated from a turbulent boundary layer and from a normal jet impingement over rigid surfaces. Comparisons with available noise measurements are made. For general turbulent flows over compliant surfaces, measurements are suggested to obtain useful data for noise predictions.
A comparative study of the efficiency of some finite difference methods for the solution of the Navier-Stokes equations was conducted. The study was restricted to the two-dimensional steady, uniform property vorticity-stream function equations. The comparisons were drawn by recording the CPU time required to obtain a solution as well as the accuracy of this solution using five numerical methods: central differences, first order upwind differences, second order upwind differences, exponential differences, and an ADI solution of the central difference equations. Solutions were obtained for two test cases: a recirculating eddy inside a square cavity with a moving top, and an impinging jet flow. The results show that whenever the central difference method is stable it generates results with a given accuracy for less CPU time than any other method.
Systematic methods based on cross-correlation techniques are presented for experimental studies of near- and farfield noise characteristics in airflow-surface interaction problems. Analyses show that, in near- and farfields, the noise characteristics due to the surface contribution of fluctuating pressures and velocities and due to the volume contribution of the turbulence in the flow can be determined separately. Both farfield noise intensities and nearfield acoustic energy fluxes can be expressed in terms of appropriate cross correlations. These correlations can be obtained by making microphone measurements in the farfield, in the nearfield, and on the surface. Examples of the applications to the noise field generated by impinging jets, by surface blowing jets, and by turbulent flow over trailing edges are presented. Advantages of the present method over conventional methods are also discussed.
Measurements of the fluctuating pressures on the wing surface of an upper-surface-blown powered-lift model and a JT15 engine were obtained using two types of pressure transducers. The pressures were measured using overall-fluctuating pressures and power spectral density analyses for various thrust settings and two jet impingement angles. Comparison of the data from the two transducers indicate that similar results are obtained in the lower frequency ranges for both transducers. The data also indicate that for this configuration, the highest pressure levels occur at frequencies below 2000 Hz.
A general analytical method is developed for determination of the radiated noise field from highly sheared, subsonic flows in the presence of rigid surfaces. The method is specifically formulated to use measurable flow field properties as the basis input data for calculations. The governing equations of a viscous, incompressible fluid are employed to determine approximately the so-called shear noise source strength distribution in the flow. Mean rates of strain and fluctuating velocity covariances are the fundamental input data for calculations. The method is applied to the wall jet region of a circular jet impinging at 45 deg to an infinite plane surface. Velocity field measurements of Foss are used to describe the required flow properties. Comparisons of calculated results with measured surface pressures and sound pressure levels are given and discussed.
A theoretical investigation was carried out to extend and improve an existing method for predicting the longitudinal characteristics of wing flap configurations with externally blown flaps (EBF). Two potential flow models were incorporated into the prediction method: a wing and flap lifting-surface model and a turbofan engine wake model. The wing-flap model uses a vortex-lattice approach to represent the wing and flaps. The jet wake model consists of a series of closely spaced vortex rings normal to a centerline which may have vertical and lateral curvature to conform to the local flow field beneath the wing and flaps. Comparisons of measured and predicted pressure distributions, span load distributions on each lifting surface, and total lift and pitching moment coefficients on swept and unswept EBF configurations are included. A wide range of thrust coefficients and flap deflection angles is considered at angles of attack up to the onset of stall. Results indicate that overall lift and pitching-moment coefficients are predicted reasonably well over the entire range. The predicted detailed load distributions are qualitatively correct and show the peaked loads at the jet impingement points, but the widths and heights of the load peaks are not consistently predicted.
A two dimensional finite difference numerical technique is presented to determine the temperature distribution of an internal cooled blade of radial turbine guide vanes. A simple convection cooling is assumed inside the guide vane blade. Such cooling has relatively small cooling effectiveness at the leading edge and at the trailing edge. Heat transfer augmentation in these critical areas may be achieved by using impingement jets and film cooling. A computer program is written in FORTRAN IV for IBM 370/165 computer.
A two-dimensional finite-difference numerical technique is presented to determine the temperature distribution of an internally-cooled blade of radial turbine guide vanes. A simple convection cooling is assumed inside the guide vane. Such an arrangement results in relatively small cooling effectiveness at the leading edge and at the trailing edge. Heat transfer augmentation in these critical areas may be achieved by using impingement jets and film cooling. A computer program is written in Fortran IV for IBM 370/165 computer.
An experimental program to obtain the fluctuating loads on the surfaces of a triple-slotted externally-blown-flap powered-lift STOL configuration was conducted. A large model of a wing/flap system and a TF-34 medium bypass ratio engine was investigated. Measurements of the fluctuating pressure, static pressure, and surface temperature resulting from the jet impingement were obtained at several locations on the surfaces of the second and third flaps. Fluctuating pressure data include overall level, power-spectral density (PSD), cross-correlation coefficient, coherency, and phase angle of the cross power-spectral density. These data indicate that more than one mechanism contributes to the fluctuating pressure levels on the flaps. In the immediate area above the intersection of the engine centerline and the flap, low frequency pressures dominate the overall fluctuating pressure levels. In other areas, such as below this intersection and outboard on the flaps, the PSD curve reaches a peak value at a Strouhal number ranging from 0.22 to 0.45.
Powered-lift concepts are utilized in aircraft currently under development for STOL application. One of the concepts, upper surface blowing, places the jet exit just above the upper surface of the wing to produce powered lift from the jet exhaust blowing over the deflected flap. New data are presented to show the effects of airspeed, angle of attack, and angle of jet impingement. Scaling relationships are investigated concerning their applicability for extrapolating data to a different model size. The effects of a number of test parameters are examined and full-scale spectra are predicted from model data. It is concluded that scale models are an effective means for obtaining fluctuating pressure spectra for use in aircraft design. The prediction of full-scale loads from model data will require geometrically accurate models and closely spaced measurement locations.
Static and wind-on tests were conducted to determine the aerodynamic characteristics of and the effects of jet impingement on the wing of a large scale upper surface blown configuration powered with an actual turbine engine. The wing and flaps were instrumented with experimental dual-sensing transducer units consisting of a fluctuating pressure gage, a vibratory accelerometer, and a surface mounted alumel thermocouple. Noise directivity and spectral content measurements were obtained for various flap configurations and various engine thrust settings to provide baseline noise data for other upper surface blown configurations.
Acoustic tests were conducted at model scale to determine the noise produced in the flyover and sideline planes at reduced separation distances between the nozzle exhaust plane and the flaps of an under-the-wing (UTW) externally blown flap (EBF) configuration in its approach attitude. Tests were also made to determine the noise suppression effectiveness of two types of passive devices which were located on the jet impingement surfaces of the configuration. In addition, static aerodynamic performance data were obtained to evaluate the penalties produced by these suppression devices. Broadband low frequency noise reductions were achieved by reducing the separation distance between the nozzle and flaps. However, mid and high frequency noise was produced which exceeded that of the reference configuration. Two passive noise suppression devices located on the flaps produced moderate to large noise reductions at reduced separation distances. Consideration of the static aerodynamic performance data obtained for the configurations tested suggests that specific broadband noise suppression characteristics may be obtained through a trade-off with aerodynamic performance penalties by the careful selection of suppression devices.
The reported investigation shows that the hot-wire probe induces stable upstream oscillations in a free shear layer, similar to the jet edge tone mechanism. This effect can be significant also in measurements involving large-scale organized structure, conditional sampling, space-time correlation, and convection velocity, when a reference or indicator probe may be used near the origin of the free shear layer. It appears that even in a free shear layer without any wedge, an object in the flow sufficiently downstream can also provide feedback to the flow upstream. A description is given of the edge-tone phenomenon which is observed when a thin slit jet impinges on a plane wedge. Attention is given to the free shear layer tone induced by a hot-wire probe, the free shear layer tone phenomenon, and shear layer tone eigenvalues and eigenfunctions.
The program aims at developing mathematical models and computer codes based on these models, which allow prediction of the product distribution in chemical reactors for converting gaseous silicon compounds to condensed-phase silicon. The major interest is in collecting silicon as a liquid on the reactor walls and other collection surfaces. Two reactor systems are of major interest, a SiCl4/Na reactor in which Si(l) is collected on the flow tube reactor walls and a reactor in which Si(l) droplets formed by the SiCl4/Na reaction are collected by a jet impingement method. During this quarter the following tasks were accomplished: (1) particle deposition routines were added to the boundary layer code; and (2) Si droplet sizes in SiCl4/Na reactors at temperatures below the dew point of Si are being calculated.