Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Heat transfer characteristics for jet array impingement with initial crossflow

Two-dimensional arrays of circular air jets impinging on a heat transfer surface parallel to the jet orifice plate are considered. The jet flow, after impingement, is constrained to exit in a single direction along the channel formed by the jet orifice plate and the heat transfer surface. In addition to the crossflow which originates from the jets following impingement, an initial crossflow is present which approaches the array through an upstream extension of the channel. The temperature of the initial crossflow air may differ from the jet air temperature. The configurations considered are intended to model the impingement cooled midchord region of gas turbine airfoils in cases where an initial crossflow is also present. Nusselt numbers and dimensionless adiabatic wall temperatures resolved to one streamwise jet hole spacing were experimentally determined for ratios of the initial crossflow rate to the total jet flow rate ranging from zero to unity. These are presented and discussed relative to the flow and geometric parameters.

Florschuetz, L. W.↗
NASA NTRS2018

Applying Machine Learning to Jet Noise Prediction

This presentation summarizes the application of machine learning to jet noise data in an effort to predict the resulting noise from the interaction between a jet and a hard surface. The Aero-Acoustic Propulsion Laboratory at the NASA Glenn Research Center has acquired the noise resulting from the interaction between a jet and metal plate over a range of surface placements (e.g. plate lengths and positions) and a range of jet flow configurations. For each configuration, the noise was measured at 24 observer locations via a microphone array centered around the jet nozzle. An artificial neural network developed with Keras and TensorFlow was trained on the data to predict an 88-band spectrum as a function of surface placement, jet conditions, and observer location. Analysis of the machine learning models provide insight into which experimental parameters contribute more to the noise and which parameters could potentially be removed entirely to simplify future experiments. Preliminary results will be discussed and presented via a live demonstration of the software, which outputs a sound spectrum in real-time with user-inputted jet-surface configurations.

Dowdall, Jonny↗
NASA NTRS1981

Streamwise flow and heat transfer distributions for jet array impingement with crossflow

Two-dimensional arrays of circular jets of air impinging on a heat transfer surface parallel to the jet orifice plate are considered. The air, after impingement, is constrained to exit in a single direction along the channel formed by the surface and the jet plate. The downstream jets are subjected to a crossflow originating from the upstream jets. Experimental and theoretical results obtained for streamwise distributions of jet and crossflow velocities are presented and compared. Measured Nusselt numbers resolved to one streamwise hole spacing are correlated with individual spanwise row jet Reynolds numbers and crossflow-to-jet velocity ratios. Correlations are presented for both inline and staggered hole patterns including effects of geometric parameters: streamwise hole spacing, spanwise hole spacing, and channel height, normalized by hole diameter. The physical mechanisms influencing heat transfer coefficients as a function of flow distribution and geometric parameters are also discussed.

Florschuetz, L. W.↗
NASA NTRS2003

Effects of Wing Leading Edge Penetration with Venting and Exhaust Flow from Wheel Well at Mach 24 in Flight

A baseline solution for CFD Point 1 (Mach 24) in the STS-107 accident investigation was modified to include effects of: (1) holes through the leading edge into a vented cavity; and (2) a scarfed, conical nozzle directed toward the centerline of the vehicle from the forward, inboard corner of the landing gear door. The simulations were generated relatively quickly and early in the investigation because simplifications were made to the leading edge cavity geometry and an existing utility to merge scarfed nozzle grid domains with structured baseline external domains was implemented. These simplifications in the breach simulations enabled: (1) a very quick grid generation procedure; and (2) high fidelity corroboration of jet physics with internal surface impingements ensuing from a breach through the leading edge, fully coupled to the external shock layer flow at flight conditions. These simulations provided early evidence that the flow through a two-inch diameter (or larger) breach enters the cavity with significant retention of external flow directionality. A normal jet directed into the cavity was not an appropriate model for these conditions at CFD Point 1 (Mach 24). The breach diameters were of the same order or larger than the local, external boundary-layer thickness. High impingement heating and pressures on the downstream lip of the breach were computed. It is likely that hole shape would evolve as a slot cut in the direction of the external streamlines. In the case of the six-inch diameter breach the boundary layer is fully ingested. The intent of externally directed jet simulations in the second scenario was to approximately model aerodynamic effects of a relatively large internal wing pressure, fueled by combusting aluminum, which deforms the corner of the landing gear door and directs a jet across the windside surface. These jet interactions, in and of themselves, were not sufficiently large to explain observed aerodynamic behavior.

Gnoffo, Peter A.↗
NASA NTRS1982

Jet array impingement flow distributions and heat transfer characteristics. Effects of initial crossflow and nonuniform array geometry

Two-dimensional arrays of circular air jets impinging on a heat transfer surface parallel to the jet orifice plate are considered. The jet flow, after impingement, is constrained to exit in a single direction along the channel formed by the jet orifice plate and the heat transfer surface. The configurations considered are intended to model those of interest in current and contemplated gas turbine airfoil midchord cooling applications. The effects of an initial crossflow which approaches the array through an upstream extension of the channel are considered. Flow distributions as well as heat transfer coefficients and adiabatic wall temperatures resolved to one streamwise hole spacing were measured as a function of the initial crossflow rate and temperature relative to the jet flow rate and temperature. Both Nusselt number profiles and dimensionless adiabatic wall temperature (effectiveness) profiles are presented and discussed. Special test results which show a significant reduction of jet orifice discharge coefficients owing to the effect of a confined crossflow are also presented, along with a flow distribution model which incorporates those effects. A nonuniform array flow distribution model is developed and validated.

Florschuetz, L. W.↗
NASA NTRS1984

Control of jet shock associated noise by a reflector

Due to the discrete noise radiation from an imperfectly expanded supersonic jet, a reflecting surface can be used to impart changes to the jet. Powell's model of screech generation is used to analytically design the reflector size necessary to cause destruction of the feedback cycle inherent to screech production. This enabled experiments to be performed over a wide range of supersonic flow conditions for a sonic nozzle in the presence of a remotely controlled reflector. Results show that not only the screech amplitude can be controlled, but that marked changes in the jet structure and broadband noise production can also be effected by changing the position of the reflector.

Norum, T. D.↗
NASA NTRS1994

The kinematics of molecular outflows

If molecular outflows represent turbulent material entrained by a central jet, then the surfaces of constant velocity should spread outward from the jet axis. Using the results of CO observations, I propose an empirical velocity distribution of this character. Outflows with this distribution display the well-documented 'acceleration' phenomenon, i.e., the increase in terminal velocity away from the driving star.

Stahler, Steven W.↗
NASA NTRSDate not supplied

Scoping of an Air Supply Configuration for AFC on a Commercial Transport Airplane High Lift System

A scoping study is being conducted on the air supply for a microjet-based active flow control (AFC) system on a twin-turbofan commercial transport airplane. Microjets provide circulation control using small surface-normal pneumatic jets located near the trailing edge of a lifting surface such as a wing or flap. When located on the pressure side of the lifting surface they increase the lift, and when located on the suction side they decrease lift. In this study, microjets are considered for installation in the flaps of the high-lift version of the Common Research Model (CRM-HL). An air supply system involving bleed air from the airplane’s auxiliary power unit (APU) plus ram air provides the air to the microjets. A model based on the 1D compressible flow equations is applied to analyze the air supply system configuration and predict the microjet flow rate with the resulting airplane performance changes based on Reynolds-averaged Navier-Stokes modeling of microjets on the CRM-HL. The results of this scoping study are encouraging in that APU air can be used to entrain ram air and thereby increase the AFC mass flow rate to achieve effective lift control and airplane performance enhancement during takeoff and landing.

AATT↗
NASA NTRSDate not supplied

Scoping of an Air Supply Configuration for AFC on a Commercial Transport Airplane High Lift System

A scoping study is being conducted on the air supply fora microjet-based active flow control (AFC) system on a twin-turbofan commercial transport airplane. Microjets provide circulation control using small surface-normal pneumatic jets located near the trailing edge of a lifting surface such as a wing or flap. When located on the pressure side of the lifting surface they increase the lift, and when located on the suction side they decrease lift. In this study, microjets are considered for installation in the flaps of the high-lift version of the Common ResearchModel (CRM-HL). Two different architectures to supply the air for the microjets are considered: (1) bleed air from the airplane’s auxiliary power unit (APU) plus ram air, and (2) engine fan bleed air plus ram air. A model based on the 1D compressible flow equations is applied to analyze the air supply system architectures and predict the microjet flow rate with the resulting airplane performance changes based on Reynolds-averaged Navier-Stokes modeling of microjets on the CRM-HL. The results of this scoping study are encouraging in that pressurized air from the APU or the engine fan can be used to entrain ram air and thereby increase the AFC mass flow rate to achieve effective lift control and airplane performance enhancement during takeoff and landing.

AATT↗
NASA NTRS1977

Acoustic loads on upper-surface-blown powered-lift systems

Powered-lift concepts are utilized in aircraft currently under development for STOL application. One of the concepts, upper surface blowing, places the jet exit just above the upper surface of the wing to produce powered lift from the jet exhaust blowing over the deflected flap. New data are presented to show the effects of airspeed, angle of attack, and angle of jet impingement. Scaling relationships are investigated concerning their applicability for extrapolating data to a different model size. The effects of a number of test parameters are examined and full-scale spectra are predicted from model data. It is concluded that scale models are an effective means for obtaining fluctuating pressure spectra for use in aircraft design. The prediction of full-scale loads from model data will require geometrically accurate models and closely spaced measurement locations.

Willis, C. M.↗
NASA NTRS1969

Scaled lunar module jet erosion experiments

An experimental research program was conducted on the erosion of particulate surfaces by a jet exhaust. These experiments were scaled to represent the lunar module (LM) during landing. A conical cold-gas nozzle simulating the lunar module nozzle was utilized. The investigation was conducted within a large vacuum chamber by using gravel or glass beads as a simulated soil. The effects of thrust, descent speed, nozzle terminal height, particle size on crater size, and visibility during jet erosion were determined. Results indicate that, from an erosion and visibility standpoint, the best landing mode for a lunar module type of vehicle would involve: site inspection and selection above the incipient erosion height, and a fast descent to the highest drop-in altitude that the vehicle structure could withstand. A slow and cautious descent with hovering just above the lunar surface would greatly increase crater size and impair visibility.

Norman S Land↗
NASA NTRS1969

Scaled Lunar Module Jet Erosion Experiments

An experimental research program was conducted on the erosion of particulate surfaces by a jet exhaust. These experiments were scaled to represent the lunar module (LM) during landing. A conical cold-gas nozzle simulating the lunar module nozzle was utilized. The investigation was conducted within a large vacuum chamber by using gravel or glass beads as a simulated soil. The effects of thrust, descent speed, nozzle terminal height, particle size on crater size, and visibility during jet erosion were determined. Results indicate that, from an erosion and visibility standpoint, the best landing mode for a lunar module type of vehicle would involve: site inspection and selection above the incipient erosion height, and a fast descent to the highest drop-in altitude that the vehicle structure could withstand. A slow and cautious descent with hovering just above the lunar surface would greatly increase crater size and impair visibility.

Experiments↗
NASA NTRS1989

Dynamic loading on impact surfaces of a high subsonic elliptic jet

The feedback resonance in a high subsonic velocity range was investigated for the case where a small aspect ratio (2:1) elliptic jet impinged perpendicularly on a flat plate. This resonance was observed for Mach numbers greater than 0.7 for plate locations between 4 and 9 major radii downstream of the exhaust plane. At the predominant resonant conditions, the loading region and sound source terms were found to be concentrated along the major axis direction on the impact surface.

Wat, J. K.↗
NASA NTRSDate not supplied

Aerodynamic Assessment of Surface-Normal Active Flow Control for Lift Enhancement on the High-Lift Common Research Model

This study explores aerodynamic feasibility of small surface-normal pneumatic jets (micro-jets) for lift enhancement on the high-lift Common Research Model. To date, lift enhancement studies using microjets have been conducted at wind tunnel Reynolds numbers less than three and half million. This paper computationally investigates microjet effects at a flight Reynolds number of24.6million. Prior to microjet activation, it is shown that flow features such as trailing edge (TE) flow separation on both inboard and outboard flaps have noticeable sensitivity to Reynolds number. At the flight Reynolds number, the onset of TE flow separation shifts downstream resulting in less flow separation compared to at the wind tunnel Reynolds numberof3.26million. The effects are insignificant for lift enhancement due to microjet on the inboard flap. However, the effects are significant for lift enhancement on the outboard flap. Microjets are shown to be more effective in circulation control on the outboard flap at the higher Reynolds number. For a microjet with velocity ratio of one, lift enhancement is increased by17%at the flight Reynolds number. This highlights the sensitivity of microjet performance to the flow features of the configuration it is implemented on. Microjet lift enhancement trends at both Reynolds numbers are found to be consistent in their ability to move the lift curve upwards in the linear regime, with the lift enhancement related to microjet momentum coefficient throughΔ𝐶𝐿=𝐾√︁𝐶𝜇. Analysis of the impact microjets have on drag shows that microjets improve the configuration’s Oswald efficiency by5.4%and2.5%at the wind tunnel and flight Reynolds numbers respectively, while providing lift enhancement. Microjet effects on the trim drag are found to be less than one percent of the total drag. The results of this study highlight the potential of small surface-normal pneumatic jets for improved performance at high-lift conditions.

ARMD↗
NASA NTRS2004

Stardust Imaging of Comet Wild 2: First Look

On 2 January 2004 during its historic flight to return cometary dust samples to earth, the STARDUST spacecraft flew within the coma of comet Wild 2 and also took 72 images where the surface was resolved during the flyby. A combination of long and short exposures was used to observe the jets and the surface. Comet Surface: The images revealed a planetary body, one not having a significant atmosphere, quite different from any other such body seen from other spacecraft. Surface depressions, potentially a combination of craters and vents, were not bowl-shaped but typically had steep walls and flattened floors. One depression considered to be a vent, the source of a jet, had a depth to diameter ratio of approx.0.4, with near vertical walls. Jets: At least 10 to possibly 20 jets were active during the flyby. Some were traced back to the surface where they seem to originate from the near vertical walls of depressions (vents) that were facing the sun, having the highest solar insolation.

Newburn, R.↗
NASA NTRS1974

A model for jet-noise analysis using pressure-gradient correlations on an imaginary cone

The technique for determining the near and far acoustic field of a jet through measurements of pressure-gradient correlations on an imaginary conical surface surrounding the jet is discussed. The necessary analytical developments are presented, and their feasibility is checked by using a point source as the sound generator. The distribution of the apparent sources on the cone, equivalent to the point source, is determined in terms of the pressure-gradient correlations.

Norum, T. D.↗