Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IMPREGNATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Partial oxidation of liquid hydrocarbons in the presence of oxygen-conducting supports: Effect of catalyst layer deposition

Ni-substituted barium hexaaluminate (BNHA) catalysts supported onto gadolinium-doped ceria (GDC), an oxygen-conductor, were prepared using two different methods: (1) conventional incipient wetness impregnation (IWI), in which a non-porous GDC support was impregnated in the conventional manner with aqueous precursors, then dried and calcined to form a supported hexaaluminate, and (2) solid-state mixing (SSM), in which solid hexaaluminate and GDC particles were mechanically ground together and thermally treated to produce a final catalyst. These catalysts were compared to bulk, unsupported BNHA; 3 wt% Ni/alumina; and 3 wt% Ni/GDC (the latter two prepared by conventional impregnation) for the partial oxidation (POX) of n-tetradecane. The reaction studies included examining the effect of 50 ppm S as dibenzothiophene (DBT) and 5 wt% 1-methylnaphthalene (MN) on the product yield under POX conditions. Temperature programmed oxidation (TPO) was used to characterize carbon formation in the reactor. The materials were characterized by BET, ICP-OES, XRD, and SEM/EDS prior to the reaction tests. Characterization of the two GDC-supported BNHA catalysts prior to the reaction studies indicated no significant differences in the bulk composition, surface area, and crystal structure. However, SEM images showed a larger amount of exposed GDC support surface area for the material prepared by IWI. Both of the GDC-supported BNHA materials demonstrated greatly reduced deactivation, with significantly reduced carbon formation compared to bulk BNHA. This was attributed to the oxygen-conducting property of the GDC, which reduced the rate of deactivation of the reaction sites by DBT and MN. The material prepared by IWI demonstrated more stable hydrogen and carbon monoxide yield than the material prepared by SSM. Although both catalysts deactivated in the presence of DBT and MN, the activity of the catalyst prepared by IWI recovered activity more quickly after the contaminants were removed. This material also maintained >50% of its initial hydrogen yield for more than 4 h after exposure to DBT and MN, while the hydrogen for the material prepared by SSM dropped to this same level within 2 h. Incipient wetness impregnation appears to provide a higher degree of interaction between the oxygenconducting GDC support and the hexaaluminate, resulting in less rapid deactivation, which appears to be due primarily to carbon deposition.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Correlating Extent of Pt–Ni Bond Formation with Low-temperature Hydrogenation of Benzene and 1,3-butadiene over Supported Pt/Ni Bimetallic Catalysts

Low-temperature hydrogenation of benzene and 1,3-butadiene on supported Pt/Ni catalysts have been used as probe reactions to correlate hydrogenation activity with the extent of Pt-Ni bimetallic bond formation. Pt/Ni bimetallic and Pt and Ni monometallic catalysts were supported on {gamma}-Al{sub 2}O{sub 3} using incipient wetness impregnation. Two sets of bimetallic catalysts were synthesized: one set to study the effect of metal atomic ratio and the other to study the effect of impregnation sequence. Fourier transform infrared spectroscopy (FTIR) CO adsorption studies were performed to characterize the surface composition of the bimetallic nanoparticles, and transmission electron microscopy (TEM) was utilized to characterize the particle size distribution. Batch reactor studies with FTIR demonstrated that all bimetallic catalysts outperformed monometallic catalysts for both benzene and 1,3-butadiene hydrogenation. Within the two sets of bimetallic catalysts, it was found that catalysts with a smaller Pt:Ni ratio possessed higher hydrogenation activity and that catalysts synthesized using co-impregnation had greater activity than sequentially impregnated catalysts. Extended X-ray absorption fine structure (EXAFS) measurements were performed in order to verify the extent of Pt-Ni bimetallic bond formation, which was found to correlate with the hydrogenation activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A highly active hybrid catalyst modified (La 0.60 Sr 0.40 ) 0.95 Co 0.20 Fe 0.80 O 3-δ cathode for proton conducting solid oxide fuel cells

The sluggish reaction kinetics in the cathode usually leads to considerable cathode polarization resistance, hindering the development of proton conducting solid oxide fuel cells (H-SOFCs) operated at intermediate temperatures (400–650 °C). In this paper, to address this problem, for the first time, a novel hybrid catalyst consisting of PrNi 0.5 Mn 0.5 O 3 and PrOx is impregnated in the (La 0.60 Sr 0.40 ) 0.95 Co 0.20 Fe 0.80 O 3-δ (LSCF) cathode of H-SOFCs, resulting in significant enhancement of the cathode reaction kinetics. Single cells with impregnated LSCF cathode and BaZr 0.8 Y 0.2 O 3 (BZY) electrolyte yield a maximum power density (MPD) of 0.198 W cm -2 at 600 °C, more than doubled of that with blank LSCF cathode (0.083 W cm -2 ). ECR and EIS studies reveal that the hybrid catalyst can substantially accelerate the oxygen-ion transfer and oxygen dissociation-absorption processes in the cathode, resulting in significantly lower polarization resistance and higher MPD. In addition, the hybrid catalyst possesses good chemical and microstructural stability at 600 °C. Consequently, the single cells with impregnated LSCF cathode show excellent durability. Finally, this study shows that the impregnation of this novel hybrid catalyst in the cathode could be a promising approach to improve the performance and stability of H-SOFCs.

36 MATERIALS SCIENCE↗

Environmental remediation with functional aerogels and xerogels

Several different types of aerogel and/or xerogel scaffolds have been demonstrated as effective sorbents for the capture and immobilization of radionuclides in gaseous form [e.g., iodine gas or I2(g), Xe] as well as ionic form (e.g., Ce4+, Cs+, I–, IO3-, Rb+, Sr2+, 99Tc7+, and U6+). These scaffolds have unique properties, which include high specific surface areas, high pore volumes, varieties of pore sizes, and functionalities that provide methods for binding radionuclides through physisorption, chemisorption, or a combination thereof. This combination of properties and functionalities make these types of materials ideal scaffolds for use as sorbents for capturing radionuclides. The primary base materials that will be discussed in this chapter include Ag0-functionalized silica aerogels, Ag+-impregnated aluminosilicate aerogels, Ag0-functionalized aluminosilicate aerogels, metal-impregnated (non-Ag) aluminosilicate aerogels and xerogels, sulfide-based aerogels, and carbon-based aerogel composites. For the capture of I2(g), the materials reported herein show some of the highest iodine loadings ever reported for inorganic sorbents. For the capture of ionic species, these materials also show promise to be some of the next generations of materials for active radionuclide remediation. This progress report will describe how these materials are fabricated, the general properties of these materials, as well as an overview of how they have been used for different applications in environmental remediation of radionuclides.

aerogel, xerogel, iodine, radionuclide remediation↗

Oxidation of Cyclopentene with Manganese Oxides Octahedral Molecular Sieves with Layer and Tunnel Structures

We report manganese oxides type octahedral molecular sieves OL-1, OMS-1, and OMS-2 were synthesized, impregnated with sodium tungstate, and evaluated as catalysts for the selective epoxidation of cyclopentene (CPE) to cyclopentene oxide (CPO) in the sodium bicarbonate/hydrogen peroxide (BAP) system. OL-1 was the best catalyst with a conversion of 78.6 % and a selectivity to CPO of 31.4 %. Impregnation with sodium tungstate affected the structure and activity of OL-1 and OMS-1. Mn 2+ is required for the epoxidation of CPE. FTIR spectra provides evidence that tungstate ions react, during impregnation, with Mg 2+ and/or Mn 2+ present in OMS-1 and OL-1 producing an amorphous compound that is not active in the epoxidation reaction. The crystalline and chemical structure of OMS-2 was not affected by tungstate impregnation, since most of the manganese occurs as Mn 3+ and Mn 4+ , which in presence of hydrogen peroxide, tend to form radicals, active in the total oxidation of organic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The effects of physical and chemical preprocessing on the flowability of corn stover

Continuous and reliable feeding of biomass is essential for successful biofuel production. However, the challenges associated with biomass solids handling are commonly overlooked. In this study, we examine the effects of preprocessing (particle size reduction, moisture content, chemical additives, etc.) on the flow properties of corn stover. Compressibility, flow properties (interparticle friction, cohesion, unconfined yield stress, etc.), and wall friction were examined for five corn stover samples: ground, milled (dry and wet), acid impregnated, and deacetylated. The ground corn stover was found to be the least compressible and most flowable material. The water and acid impregnated stovers had similar compressibilities. Yet, the wet corn stover was less flowable than the acid impregnated sample, which displayed a flow index equivalent to the dry, milled corn stover. The deacetylated stover, on the other hand, was the most compressible and least flowable examined material. However, all of the tested stover samples had internal friction angles >30°, which could present additional feeding and handling challenges. All of the ''wetted'' materials (water, acid, and deacetylated) displayed reduced flowabilities (excluding the acid impregnated sample), and enhanced compressibilities and wall friction angles, indicating the potential for added handling issues; which was corroborated via theoretical hopper design calculations. All of the ''wetted'' corn stovers require larger theoretical hopper outlet diameters and steeper hopper walls than the examined ''dry'' stovers.

09 BIOMASS FUELS↗

Synthesis and characterization of NiO-YSZ for SOFCs

Nickel oxide and yttria-stabilized zirconia ceramic materials were prepared by three methods: physical mixture, a modified Pechini route, and impregnation with Ni(NO{sub 3}){sub 2}.6H{sub 2}O. Temperature-programmed reduction (TPR) analysis showed the presence of different reduction peaks for each sample and that the reduction temperature was influenced by the employed preparation procedure. Nickel oxide species are completely reduced at temperatures up to 1000 deg. C and their temperature-programmed reduction profiles indicated that a higher temperature reduction corresponds to a higher calcination temperature. Furthermore, the composites synthesized through impregnation presented nickel oxide species more easily reducible than those prepared by the two other methods. Scanning electron microscopy and X-ray photoelectron spectroscopy (XPS) evidenced a larger nickel oxide coating on yttria-stabilized zirconia for the composite synthesized through the impregnation method. The electrical conductivity of impregnation sample was 117 S cm{sup -1} at 850 deg. C, a value three times higher than that of the physical mixture.

36 MATERIALS SCIENCE↗

Preparation of sodium humate/{alpha}-aluminum oxide adsorbents for flue gas desulfurization

A new composite adsorbent of sodium humate (HNa)=alpha-aluminium oxide ({alpha}-Al{sub 2}O{sub 3}) for flue gas desulfurization (FGD) was prepared using the impregnation method. Both the adsorbent of {alpha}-Al{sub 2}O{sub 3} and HNa={alpha}-Al{sub 2}O{sub 3} were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), energy dispersive X-ray spectrometer (EDS), and scanning electron microscope (SEM). Desulfurization activity of the adsorbent impregnated with ammonia (NH{sub 4}OH) was investigated in a fixed-bed quartz reactor. Experimental results indicate that HNa, which coats the {alpha}-Al{sub 2}O{sub 3} fibers impregnated with HNa solution, improved the property of {alpha}-Al{sub 2}O{sub 3} support for FGD. On the other hand, the HNa-coating on the adsorbent of HNa/{alpha}-Al{sub 2}O{sub 3} impregnated with NH{sub 4}OH played an important role in enhancing the desulfurization property of the {alpha}-Al{sub 2}O{sub 3}. Due to the strong adsorption capability of HNa, more NH{sub 4}OH was adsorbed in the adsorbent of HNa/{alpha}-Al{sub 2}O{sub 3} the longer a high sulfur dioxide (SO{sub 2}) conversation rate was maintained. In addition, because the desulfurization product was a compound fertilizer consisting of ammonium sulfate ((NH{sub 4}){sub 2}SO{sub 4}), ammonium humate (HNH{sub 4}), and HNa, the recycling use of {alpha}-Al{sub 2}O{sub 3} was also easily achieved. Thus, this study can provide a new cost-effective way to remove SO{sub 2} from flue gas.

01 COAL, LIGNITE, AND PEAT↗

Potassium permanganate for mercury vapor environmental control

Potassium permanganate (KMnO4) was evaluated for application in removing mercury vapor from exhaust air systems. The KMnO4 may be used in water solution with a liquid spray scrubber system or as a solid adsorber bed material when impregnated onto a zeolite. Air samples contaminated with as much as 112 mg/cu m of mercury were scrubbed to 0.06mg/cum with the KMnO4-impregnated zeolite (molecular sieve material). The water spray solution of permanganate was also found to be as effective as the impregnated zeolite. The KMnO4-impregnated zeolite was applied as a solid adsorber material to (1) a hardware decontamination system, (2) a model incinerator, and (3) a high vacuum chamber for ion engine testing with mercury as the propellant. A liquid scrubber system was also applied in an incinerator system. Based on the results of these experiments, it is concluded that the use of KMnO4 can be an effective method for controlling noxious mercury vapor.

Kuivinen, D. E.↗

Development of uniform and predictable battery materials for nickel-cadmium aerospace cells

The objective of this study was to analyze battery materials and manufacturing methods with the aim of developing uniform and predictable battery plates for nickel cadmium aerospace cells. The results are presented of an extensive factorially-designed experiment aimed at illuminating, in a comparative study, the effect of plaque preparation, plaque thickness, impregnation process, and loading level with active material. The following impregnation processes were investigated: (1) chemical conversion, (2) electrochemical conversion, and (3) high temperature electrochemical impregnation. The test parameter on which the conclusion regarding the manufacturing variables are based was the capacity change during a simulated near-earth orbit cycle regime. As operational variables, the effect of various charge and discharge rates was investigated. During the 100 test cycles, overall capacity changes of positive plates and the differences between the various plates were found to be small. Plates prepared by the high temperature electrochemical impregnation of slurry-coated plaque (at the conditions used) showed surface buildup of active material. They also retained slightly less of their capacity during cycling compared to other plate preparations.

Source record↗

Improvement in oxidation resistance of the leading edge thermal protection for a space shuttle

To improve the oxidation resistance of a carbon-carbon composite, impregnations were performed using pitches, polyfurfuryl alcohols, and phenolic resins, including a silicon-doped phenolic resin. Oxidation resistance and strength increased for all of the composites as the impregnant-carbon residue increased. The properties of the composites impregnated with the nonsilicon-bearing resins were nearly identical and depended only on the amount of impregnant residue present. However, for equivalent residue concentrations, composites produced with the silicon-bearing resin gave higher strengths and at least 100% better oxidation resistance than was observed for the other composites or for a prototype control material.

Williams, J. M.↗

Evaluation of positive plates with various loading levels

The effects of overcharge and total cycling rate on one electrochemically impregnated and four chemically impregnated nickel electrodes are examined. Topics discussed include porosity distribution, electrode corrosion, electrolyte absorption and positive electrode involvement in the decrease in the amount of electrolyte in the separator. The electrochemically impregnated electrode is shown to be superior to all types of conventionally impregnated electrodes regardless of the loading level.

Vanommering, G.↗

Method for stabilizing thick honeycomb core composite articles

A method of stabilizing thick honeycomb core composites is disclosed. The method comprises bonding a layer of resin impregnated woven graphite fibers to one surface of the honeycomb core, then curing the resin impregnates forming a stabilized honeycomb core. This stabilized core is then cut to net shape and the composite structure is formed by laying one or more resin impregnated fiber layers onto the stabilized core surf aces and curing the lay-up under heat and pressure forming the composite article. Also disclosed is a stabilized honeycomb subassembly formed by bonding a graphite fiber, resin impregnated layer onto one of the honeycomb core surfaces and curing the resins, then shaping the stabilized honeycomb core to the desired form.

Gary J Jacaruso↗

Process for preparing tapes from thermoplastic polymers and carbon fibers

The instant invention involves a process for use in preparing tapes or rovings, which are formed from a thermoplastic material used to impregnate longitudinally extended bundles of carbon fibers. The process involves the steps of (a) gas spreading a tow of carbon fibers; (b) feeding the spread tow into a crosshead die; (c) impregnating the tow in the die with a thermoplastic polymer; (d) withdrawing the impregnated tow from the die; and (e) gas cooling the impregnated tow with a jet of air. The crosshead die useful in the instant invention includes a horizontally extended, carbon fiber bundle inlet channel, means for providing melted polymer under pressure to the die, means for dividing the polymeric material flowing into the die into an upper flow channel and a lower flow channel disposed above and below the moving carbon fiber bundle, means for applying the thermoplastic material from both the upper and lower channels to the fiber bundle, and means for withdrawing the resulting tape from the die.

Chung, Tai-Shung↗

Low-Density, Aerogel-Filled Thermal-Insulation Tiles

Aerogel fillings have been investigated in a continuing effort to develop low-density thermal-insulation tiles that, relative to prior such tiles, have greater dimensional stability (especially less shrinkage), equal or lower thermal conductivity, and greater strength and durability. In preparation for laboratory tests of dimensional and thermal stability, prototypes of aerogel-filled versions of recently developed low-density tiles have been fabricated by impregnating such tiles to various depths with aerogel formations ranging in density from 1.5 to 5.6 lb/ft3 (about 53 to 200 kg/cu m). Results available at the time of reporting the information for this article showed that the thermal-insulation properties of the partially or fully aerogel- impregnated tiles were equivalent or superior to those of the corresponding non-impregnated tiles and that the partially impregnated tiles exhibited minimal (<1.5 percent) shrinkage after multiple exposures at a temperature of 2,300 F (1,260 C). Latest developments have shown that tiles containing aerogels at the higher end of the density range are stable after multiple exposures at the said temperature.

Santos, Maryann↗

Stabilized sulfur binding using activated fillers

A method of making a stable, sulfur binding composite comprising impregnating a solid aggregate with an organic modifier comprising unsaturated hydrocarbons with at least one double or triple covalent bond between adjacent carbon atoms to create a modifier-impregnated aggregate; heating and drying the modifier-impregnated aggregate to activate the surface of the modifier-impregnated aggregate for reaction with sulfur.

36 MATERIALS SCIENCE↗

Engineering New Catalysts for In-Process Elimination of Tars

The key objective of this project was to develop a new and more efficient methodology for engineering and economically producing optimized robust catalysts for the reduction or elimination of tars in biomass gasification. Whereas current catalyst technology typically disposes thin layers of catalytically-active material onto rigid supports via wet chemistry-based methods, this project investigated novel thermal methods for directly incorporating catalytically active materials onto robust supports as well as novel approaches for incorporating catalytically active materials on and/or within an otherwise inert refractory support material which is then subsequently formed and processed to create a catalytically-active material on all exposed surfaces. Specifically, the focus of this engineered catalyst development was on materials which were derived from, or otherwise related to, olivine-like minerals, due to the inherent attrition resistance and moderate catalytic properties exhibited by natural olivine when used in a fluidized bed biomass gasifier. Task 1 of this project successfully demonstrated the direct thermal impregnation of catalytically-active materials onto an olivine substrate, with the production of a Ni-olivine catalyst. Nickel and nickel oxide were thermally impregnated onto an olivine substrate and when reduced were shown to demonstrate improved catalytic activity over the baseline olivine material and equal the tar-decomposing performance of Ni-olivine catalysts prepared by conventional wet impregnation. Task 2 involved coordination with our subcontracted project partners to further develop and characterize catalyst formulations and to optimize activity and production methods. Within this task, several significant new materials were developed. NexTech Materials developed a sintered ceramic nickel-magnesium-silicate catalyst that demonstrated superb catalytic activity and high resistance to deactivation by H2S. Alfred University developed both supported and integrated (bulk) catalysts via a glass-ceramic processing route which were shown to exhibit excellent catalytic activity and superior resistance to attrition deactivation. With the discovery of these active, robust, glass-based catalysts, and with the permission of the project officer, the investigation of waste-based materials as originally proposed for Task 3 and pilot-scale testing proposed in Task 5 were deferred indefinitely in favor of further investigation of the glass-ceramic based catalyst materials. This choice was justified in part because during FY 2006 and through FY 2007, funding restrictions imposed by congressional budget choices significantly reduced funding for DOE biomass-related projects. Funding for this project was limited to what had been authorized which slowed the pace of project work at GTI so that our project partners could continue in their work. Thereafter, project work was allowed to resume and with restored funding, the project continued and concentrated on the development and testing of glass-ceramic catalysts in bulk or supported formats. Work concluded with a final development devoted to increasing the surface area of glass-ceramic catalysts in the form of microspheres. Following that development, project reporting was completed and the project was concluded.

03 NATURAL GAS↗

Experimental and computational study of the microporous layer and hydrophobic treatment in the gas diffusion layer of a proton exchange membrane fuel cell

Enabling fuel cell operation at high current density is critical for developing competitive alternative power system to replace internal combustion engine. However, liquid water management continues to be a challenge for high humidity or high current density operation. Water condensation in the porous media hinders efficient oxygen transport to the catalyst layer, which in turns, reduces fuel cell performance. To improve water management capability, the gas diffusion layer is often impregnated with Polytetrafluoroethylene (PTFE) and coated with a thin microporous layer, which have shown to improve fuel cell performance, especially under wet conditions. However, the fundamental mechanism that drives the performance enhancement is still not well understood. In this work, the effects of PTFE impregnation and MPL were studied using both experimental and computational techniques. Both limiting current and polarization tests under dry and wet operating condition are conducted to study the oxygen transport resistance and fuel cell performance. In addition, a 2-D, two-phase, multi-physics PEMFC model is developed to simulate performance and gain a fundamental understanding of local water saturation and oxygen concentration. The combined results show that 5 wt% PTFE impregnation with MPL significantly enhances liquid water management, which enables higher current density operation of a fuel cell.

25 ENERGY STORAGE↗