Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “High frequency analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Compressibility effects on rotor forces in the leakage path between a shrouded pump impeller and its housing

A modified approach to Childs' previous work on fluid-structure interaction forces in the leakage path between an impeller shroud and its housing is presented in this paper. Three governing equations consisting of continuity, path-momentum, and circumferential-momentum equations were developed to describe the leakage path inside a pump impeller. Radial displacement perturbations were used to solve for radial and circumferential force coefficients. In addition, impeller-discharge pressure disturbances were used to obtain pressure oscillation responses due to precessing impeller pressure wave pattern. Childs' model was modified from an incompressible model to a compressible barotropic-fluid model (the density of the working fluid is a function of the pressure and a constant temperature only). Results obtained from this model yielded interaction forces for radial and circumferential force coefficients. Radial and circumferential forces define reaction forces within the impeller leakage path. An acoustic model for the same leakage path was also developed. The convective, Coriolis, and centrifugal acceleration terms are removed from the compressible model to obtain the acoustics model. A solution due to impeller discharge pressure disturbances model was also developed for the compressible and acoustics models. The results from these modifications are used to determine what effects additional perturbation terms in the compressible model have on the acoustic model. The results show that the additional fluid mechanics terms in the compressible model cause resonances (peaks) in the force coefficient response curves. However, these peaks only occurred at high values of inlet circumferential velocity ratios greater than 0.7. The peak pressure oscillation was shown to occur at the wearing ring seal. Introduction of impeller discharge disturbances with n = 11 diametral nodes showed that maximum peak pressure oscillations occurred at nondimensional precession frequencies of f = 6.4 and f = 7.8 for this particular pump. Bolleter's results suggest that for peak pressure oscillations to occur at the wearing ring seal, the nondimensional excitation frequency should be on the order of f = 2.182 for n = 11. The resonances found in this research do not match the excitation frequencies predicted by Bolleter. At the predicted peak excitation frequencies given by Bolleter, the compressible model shows an attenuation of the pressure oscillations at the seal exit. The compressibility of the fluid does not have a significant influence on the model at low values of nondimensional excitation frequency. At high values of nondimensional frequency, the effects of compressibility become more significant. For the acoustic analysis, the convective, Coriolis, and centrifugal acceleration terms do affect the results to a limited extent for precession excitation and to a large extent for a pressure excitation when the fluid operates at relatively high Mach numbers.

Cao, Nhai The↗
NASA NTRS2012

Interpretation of Vector Electric Field Measurements of Bursty Langmuir Waves in the Cusp

An analysis of auroral Langmuir waves in the cusp observed by two high-frequency electric field instruments on the TRICE high-flyer sounding rocket shows many examples of Langmuir wave bursts modulated at approximately 10 kHz. Previous studies have explained these and similar observations as the result of beating between waves with very close frequencies near the Langmuir cutoff, resulting from either wave-wave interactions or independent linear excitations. The unique three-dimensional (3-D) data set provided by the NASA Goddard Space Flight Center TAEFWD instrument shows that up to 25% of waveforms selected from the most intense bursts exhibit anisotropic modulations, i.e., the beat nulls and peaks are not aligned in time across the three perpendicular electric field components. Modulations of this type arise when superposed wave normal modes possess differing polarizations, and simulations using wave modes calculated with the J-WHAMP numerical dispersion code show (1) that waves with differing polarizations can exist in conditions like those observed by TRICE-High and (2) that superpositions of such waves can produce anisotropic modulation. Fourier analysis of the 3-D waveform data suggests that both linear and elliptically polarized waves are present near the Langmuir cutoff at these times. These observations illustrate how 3-D measurements can give valuable insight into the nature of wave interactions in the auroral plasma environment.

Dombrowski, M. P.↗
NASA NTRS1988

Active control of tiltrotor blade in-plane loads during maneuvers

The origin of one/rev rotor aerodynamic loads which arise in tiltrotor aircraft during airplane-mode high speed pull-up and push-over maneuvers is examined using a coupled rotor/fuselage dynamic simulation. A modified eigenstructure assignment technique is used to design a controller which alleviates the in-plane loads during high pitch rate maneuvers. The controller utilizes rotor cyclic pitch inputs to restructure the aircraft short period and phugoid responses in order to achieve the coupling between pitch rate and rotor flapping responses which minimizes the rotor aerodynamic loading. Realistic time delays in the feedback path are considered during the controller design. Stability robustness in the presence of high frequency modeling errors is ensured through the use of singular value analysis.

Miller, David G.↗
NASA NTRS1992

Monitoring Polymer Curing Via Electromagnetic Impedance

New nondestructive in-situ electromagnetic-impedance measurement technique senses cure-processing properties of high-temperature, high-performance thermostat and thermoplastic resins. Continuous frequency-dependent measurement and analysis performed during curing cycle. Monitors and measures molecular properties of polymeric resin in liquid and solid states. Applications include nondestructive means for evaluation of materials, determination of "window" boundaries of curing cycles of thermoplastics and thermoset resins, and for online, closed-loop control of curing cycles.

Freeman, William T.↗
NASA NTRS1992

Analysis of rotor vibratory loads using higher harmonic pitch control

Experimental studies of isolated rotors in forward flight have indicated that higher harmonic pitch control can reduce rotor noise. These tests also show that such pitch inputs can generate substantial vibratory loads. The modification is summarized of the RotorCRAFT (Computation of Rotor Aerodynamics in Forward flighT) analysis of isolated rotors to study the vibratory loading generated by high frequency pitch inputs. The original RotorCRAFT code was developed for use in the computation of such loading, and uses a highly refined rotor wake model to facilitate this task. The extended version of RotorCRAFT incorporates a variety of new features including: arbitrary periodic root pitch control; computation of blade stresses and hub loads; improved modeling of near wake unsteady effects; and preliminary implementation of a coupled prediction of rotor airloads and noise. Correlation studies are carried out with existing blade stress and vibratory hub load data to assess the performance of the extended code.

Quackenbush, Todd R.↗
NASA NTRS1994

On the Behavior of Three-dimensional Wave Packets in Viscously Spreading Mixing Layers

We consider analytically the evolution of a three-dimensional wave packet generated by an impulsive source in a mixing layer. The base flow is assumed to be spreading due to viscous diffusion. The analysis is restricted to small disturbances (linearized theory). A suitable high-frequency ansatz is used to describe the packet; the key elements of this description are a complex phase and a wave action density. It is found that the product of this density and an infinitesimal material volume convecting at the local group velocity is not conserved: there is a continuous interaction between the base flow and the wave action. This interaction is determined by suitable mode-weighted averages of the second and fourth derivatives of the base-flow velocity profile. Although there is some tendency for the dominant wave number in the packet to shift from the most unstable value toward the neutral value, this shift is quite moderate. In practice, wave packets do not become locally neutral in a diverging base flow (as do instability modes), therefore, they are expected to grow more suddenly than pure instability modes and do not develop critical layers. The group velocity is complex; the full significance of this is realized by analytically continuing the equations for the phase and wave action into a complex domain. The implications of this analytic continuation are discussed vis-a-vis the secondary instabilities of the packet: very small scale perturbations on the phase can grow very rapidly initially, but saturate later because most of the energy in these perturbations is convected away by the group velocity. This remark, as well as the one regarding critical layers, has consequences for the nonlinear theories.

Balsa, Thomas F.↗
NASA NTRS1992

Convective and morphological instabilities during crystal growth: Effect of gravity modulation

During directional solidification of a binary alloy at constant velocity in the vertical direction, morphological and convective instabilities may occur due to the temperature and solute gradients associated with the solidification process. The effect of time-periodic modulation (vibration) is studied by considering a vertical gravitational acceleration which is sinusoidal in time. The conditions for the onset of solutal convection are calculated numerically, employing two distinct computational procedures based on Floquet theory. In general, a stable state can be destabilized by modulation and an unstable state can be stabilized. In the limit of high frequency modulation, the method of averaging and multiple-scale asymptotic analysis can be used to simplify the calculations.

Coreill, S. R.↗
NASA NTRS2007

Roller Bearing Health Monitoring Using CPLE Frequency Analysis Method

This paper describes a unique vibration signature analysis technique Coherence Phase Line Enhancer (CPLE) Frequency Analysis - for roller bearing health monitoring. Defects of roller bearing (e.g. wear, foreign debris, crack in bearing supporting structure, etc.) can cause small bearing characteristic frequency shifts due to minor changes in bearing geometry. Such frequency shifts are often too small to detect by the conventional Power Spectral Density (PSD) due to its frequency bandwidth limitation. This Coherent Phase Line Enhancer technology has been evolving over the last few years and has culminated in the introduction of a new and novel frequency spectrum which is fully described in this paper. This CPLE technology uses a "key phasor" or speed probe as a preprocessor for this analysis. With the aid of this key phasor, this CPLE technology can develop a two dimensional frequency spectrum that preserves both amplitude and phase that is not normally obtained using conventional frequency analysis. This two-dimensional frequency transformation results in several newly defined spectral functions; i. e. CPLE-PSD, CPLE-Coherence and the CPLE-Frequency. This paper uses this CPLE frequency analysis to detect subtle, low level bearing related signals in the High Pressure Fuel Pump (HPFP) of the Space Shuttle Main Engine (SSME). For many rotating machinery applications, a key phasor is an essential measurement that is used in the detection of bearing related signatures. There are times however, when a key phasor is not available; i. e. during flight of any of the SSME turbopumps or on the SSME High Pressure Oxygen Turbopump (HPOTP) where no speed probe is present. In this case, the CPLE analysis approach can still be achieved using a novel Pseudo Key Phasor (PKP) technique to reconstruct a 1/Rev PKP signal directly from external vibration measurements. This paper develops this Pseudo Key Phasor technique and applies it to the SSME vibration data.

Jong, Jen-Yi↗
NASA NTRS2009

Dynamic Measurement of Temperature, Velocity, and Density in Hot Jets Using Rayleigh Scattering

A molecular Rayleigh scattering technique is utilized to measure gas temperature, velocity, and density in unseeded gas flows at sampling rates up to 10 kHz, providing fluctuation information up to 5 kHz based on the Nyquist theorem. A high-power continuous-wave laser beam is focused at a point in an air flow field and Rayleigh scattered light is collected and fiber-optically transmitted to a Fabry-Perot interferometer for spectral analysis. Photomultiplier tubes operated in the photon counting mode allow high-frequency sampling of the total signal level and the circular interference pattern to provide dynamic density, temperature, and velocity measurements. Mean and root mean square velocity, temperature, and density, as well as power spectral density calculations, are presented for measurements in a hydrogen-combustor heated jet facility with a 50.8-mm diameter nozzle at NASA John H. Glenn Research Center at Lewis Field. The Rayleigh measurements are compared with particle image velocimetry data and computational fluid dynamics predictions. This technique is aimed at aeronautics research related to identifying noise sources in free jets, as well as applications in supersonic and hypersonic flows where measurement of flow properties, including mass flux, is required in the presence of shocks and ionization occurrence.

Mielke, Amy F.↗
NASA NTRS1961

Analytical Investigation of an Adaptive Flight-Control System Using a Sinusoidal Test Signal

An analytical study was made of an adaptive flight-control system which measures vehicle response to small-amplitude control-surface deflections produced by a sinusoidal test signal. Changes in the response to this signal are related to environmental changes,, and the system is continuously altered to maintain this response equal to a preselected value. The system is suitable for use in high-performance aircraft and missiles and requires only the addition of a signal generator and a logic circuit consisting of a filter-rectifier network and a comparator-integrator network to a basic command-control system. Thus, it presents a relatively simple approach to the problem. The effects on system performance of variation in flight condition, system-gain level, test-signal frequency, and sensor location are included in the analysis. Longitudinal control of a high-performance research aircraft over flight conditions ranging from landing approach to a Mach number of 5.8 at an altitude of 150,000 feet, and longitudinal control of a four-stage solid-fuel missile including the first bending mode over the atmospheric portion of a launch trajectory constituted the basis for the analytical study. Results of an analog-computer study using time-varying coefficients are presented to compare the control obtained with the adaptive system with-that obtained with a fixed-gain system during the atmospheric portion of a missile launch trajectory. The system has demonstrated an ability to maintain satisfactory vehicle control-system stability over wide ranges of environmental change.

Harris, Jack E.↗
NASA NTRS1983

Propagation of sound in highly porous open-cell elastic foams

This work presents both theoretical predictions and experimental measurements of attenuation and progressive phase constants of sound in open-cell, highly porous, elastic polyurethane foams. The foams are available commercially in graded pore sizes for which information about the static flow resistance, thermal time constant, volume porosity, dynamic structure factor, and speed of sound is known. The analysis is specialized to highly porous foams which can be efficient sound absorbers at audio frequencies. Negligible effect of internal wave coupling on attenuation and phase shift for the frequency range 16-6000 Hz was predicted and no experimentally significant effects were observed in the bulk samples studied. The agreement between predictions and measurements in bulk materials is excellent. The analysis is applicable to both the regular and compressed elastic open-cell foams.

Lambert, R. F.↗
NASA NTRS1990

LOX manifold tee analysis

A 4000 Hz vibration phenomena was observed during the test firings of several space shuttle main engines (SSME). Experimental studies of this phenomena suggest that the problem might be associated with vortex shedding from the vanes within the LOX tee manifold. The objective of this study was to determine the unsteady, 3-D flow associated with these vanes by computational methods to identify and better understand the 4000 Hz vibration phenomena. A flow solver, FDNS, for the turbulent conservation equations was validated for predicting high frequency vortex dynamics and used to predict 2-D and 3-D flows within the LOX tee. 4000 Hz excitation oscillations were predicted for some flows and the entire 3-D flow structure was predicted for LOX tee flow. The complexity of the flow was revealed by this analysis, and computational methods for predicting these high frequency oscillations in future engine systems were established.

Chen, Yen-Sen↗
NASA NTRSDate not supplied

Validation of Shadowgraph Spectral Analysis using an SLS Block 2 Wind-Tunnel Model

A flow quantification method has previously been developed that uses high-speed shadowgraph images to extract frequency content of a transonic flow field around a wind-tunnel model. In this method, a classical spectral analysis is performed on a set of shadowgraph image pixels to identify their intensity fluctuation frequencies. The spatial change of the image intensity is related to the second derivative of the density gradient. Examining the change of the density gradient as a function of time can be used to understand the flow field pressure fluctuations. Pressure measurements collected during a Booster Obsolescence Life Extension Forward Attachment Structure Trade Study Test are used to calibrate the shadowgraph-based measurements. The test was performed at the NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-foot test section and investigated aerodynamic environment downstream of various booster forward attachment hardware geometries of the Space Launch System Block 2 Cargo configuration. Time-correlated shadowgraph video and model surface pressure measurements were acquired during the test and served as an ideal opportunity to calibrate and validate the shadowgraph image intensity method.

Shadowgraph↗
NASA NTRSDate not supplied

Validation of Shadowgraph Spectral Analysis using an SLS Block 2 Wind-Tunnel Model

A flow quantification method has previously been developed that uses high-speed shadowgraph images to extract frequency content of a transonic flow field around a wind-tunnel model. In this method, a classical spectral analysis is performed on shadowgraph video pixels to identify their intensity fluctuation frequencies. The spatial change of the image intensity is related to the second derivative of the density gradient. Examining the change of the density gradient as a function of time can be used to understand the flow-field pressure fluctuations. Time-varying pressure measurements collected during a Space Launch System (SLS) unsteady aerodynamic test of an advanced Block 2 booster design are used to calibrate the shadowgraph-based measurements. The test was performed at the NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-foot test section and investigated the aerodynamic environment downstream of candidate booster forward attachment hardware geometries of the SLS Block 2 Cargo configuration. Time-correlated shadowgraph video and model surface pressure measurements were acquired during the test and served as an ideal opportunity to calibrate and validate the shadowgraph image intensity method.

Shadowgraph↗
NASA NTRSDate not supplied

Validation of Shadowgraph Spectral Analysis using an SLS Block 2 Wind-Tunnel Model

A flow quantification method has previously been developed that uses high-speed shadowgraph images to extract frequency content of a transonic flow field around a wind-tunnel model. In this method, a classical spectral analysis is performed on shadowgraph video pixels to identify their intensity fluctuation frequencies. The spatial change of the image intensity is related to the second derivative of the density gradient. Examining the change of the density gradient as a function of time can be used to understand the flow-field pressure fluctuations. Time-varying pressure measurements collected during a Space Launch System (SLS) unsteady aerodynamic test of an advanced Block 2 booster design are used to calibrate the shadowgraph-based measurements. The test was performed at the NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-foot test section and investigated the aerodynamic environment downstream of candidate booster forward attachment hardware geometries of the SLS Block 2 Cargo configuration. Time-correlated shadowgraph video and model surface pressure measurements were acquired during the test and served as an ideal opportunity to calibrate and validate the shadowgraph image intensity method.

Shadowgraph↗
NASA NTRS2011

Ares I-X Flight Test Validation of Control Design Tools in the Frequency-Domain

A major motivation of the Ares I-X flight test program was to Design for Data, in order to maximize the usefulness of the data recorded in support of Ares I modeling and validation of design and analysis tools. The Design for Data effort was intended to enable good post-flight characterizations of the flight control system, the vehicle structural dynamics, and also the aerodynamic characteristics of the vehicle. To extract the necessary data from the system during flight, a set of small predetermined Programmed Test Inputs (PTIs) was injected directly into the TVC signal. These PTIs were designed to excite the necessary vehicle dynamics while exhibiting a minimal impact on loads. The method is similar to common approaches in aircraft flight test programs, but with unique launch vehicle challenges due to rapidly changing states, short duration of flight, a tight flight envelope, and an inability to repeat any test. This paper documents the validation effort of the stability analysis tools to the flight data which was performed by comparing the post-flight calculated frequency response of the vehicle to the frequency response calculated by the stability analysis tools used to design and analyze the preflight models during the control design effort. The comparison between flight day frequency response and stability tool analysis for flight of the simulated vehicle shows good agreement and provides a high level of confidence in the stability analysis tools for use in any future program. This is true for both a nominal model as well as for dispersed analysis, which shows that the flight day frequency response is enveloped by the vehicle s preflight uncertainty models.

Johnson, Matthew↗
NASA NTRS2008

Noise Radiation from a Continuous Mold-Line Link Flap Configuration

The results of an experimental study of the noise from a Continuous Mold-Line Link (CML) flap are presented. Acoustic and unsteady surface pressure measurements were performed on a main element wing section with a half-span CML flap in NASA Langley s Quiet Flow Facility. The acoustic data were acquired with a medium aperture directional array (MADA) of microphones. The Deconvolution Approach for the Mapping of Acoustic Sources (DAMAS) method is applied to determine the spatial distribution and strength of the noise sources over the surface of the test model. A Coherent Output Power (COP) method which relates the output from unsteady surface pressure sensors to the output of the MADA is also used to obtain more detailed characteristics of the noise source distribution in the trailing edge region of the CML. These results are compared to those obtained for a blunt flap to quantify the level of noise benefit that is achieved with the CML flap. The results indicate that the noise from the CML region of the flap is 5 to 17 dB lower (depending on flap deflection and Mach number) than the noise from the side edge region of the blunt flap. Lower noise levels are obtained for all frequencies. Spectral analysis of the noise from the cove region of the CML and blunt flap models also reveal a spectral peak in the high frequency range that is related to noise scattering at the trailing edge of the main element. The peaks in the CML and blunt flap cove noise spectra are close in level and often exceed blunt side edge noise. Applying a strip of serrated tape to the trailing edge of the CML flap model main airfoil, reduced the peak but increased other noise somewhat. Directivity measurements show that the CML flap can be more directional than the blunt flap.

Hutcheson, Florence V.↗
NASA NTRS2011

Noise Radiation from a Continuous Mold-Line Link Flap Configuration

The results of an experimental study of the noise from a Continuous Mold-Line Link (CML) flap are presented. Acoustic and unsteady surface pressure measurements were performed on a main element wing section with a half-span CML flap in NASA Langley s Quiet Flow Facility. The acoustic data were acquired with a medium aperture directional array (MADA) of microphones. The Deconvolution Approach for the Mapping of Acoustic Sources (DAMAS) method is applied to determine the spatial distribution and strength of the noise sources over the surface of the test model. A Coherent Output Power (COP) method which relates the output from unsteady surface pressure sensors to the output of the MADA is also used to obtain more detailed characteristics of the noise source distribution in the trailing edge region of the CML. These results are compared to those obtained for a blunt flap to quantify the level of noise benefit that is achieved with the CML flap. The results indicate that the noise from the CML region of the flap is 5 to 17 dB lower (depending on flap deflection and Mach number) than the noise from the side edge region of the blunt flap. Lower noise levels are obtained for all frequencies. Spectral analysis of the noise from the cove region of the CML and blunt flap models also reveal a spectral peak in the high frequency range that is related to noise scattering at the trailing edge of the main element. The peaks in the CML and blunt flap cove noise spectra are close in level and often exceed blunt side edge noise. Applying a strip of serrated tape to the trailing edge of the CML flap model main airfoil reduced the peak but increased other noise somewhat. Directivity measurements show that the CML flap can be more directional than the blunt flap.

Hutcheson, Florence V.↗