Results for “Heat conduction modeling” — Page 13

NASA NTRS2008

Multispectral Emission of the Sun during the First Whole Sun Month: Magnetohydrodynamic Simulations

We demonstrate that a three-dimensional magnetohydrodynamic (MHD) simulation of the corona can model its global plasma density and temperature structure with sufficient accuracy to reproduce many of the multispectral properties of the corona observed in extreme ultraviolet (EW) and X-ray emission. The key ingredient to this new type of global MHD model is the inclusion of energy transport processes (coronal heating, anisotropic thermal conduction, and radiative losses) in the energy equation. The calculation of these processes has previously been confined to one-dimensional loop models, idealized two-dimensional computations, and three-dimensional active region models. We refer to this as the thermodynamic MHD model, and we apply it to the time period of Carrington rotation 1913 (1996 August 22 to September 18). The form of the coronal heating term strongly affects the plasma density and temperature of the solutions. We perform our calculation for three different empirical heating models: (1) a heating function exponentially decreasing in radius; (2) the model of Schrijver et al.; and (3) a model reproducing the heating properties of the quiet Sun and active regions. We produce synthetic emission images from the density and temperature calculated with these three heating functions and quantitatively compare them with observations from E W Imaging Telescope on the Solar and Heliospheric Observatory and the soft X-ray telescope on Yohkoh. Although none of the heating models provide a perfect match, heating models 2 and 3 provide a reasonable match to the observations.

Lionello, Roberto↗

NASA NTRS2009

Validation of PICA Ablation and Thermal-Response Model at Low Heat Flux

Phenolic Impregnated Carbon Ablator (PICA) was the forebody heatshield material on the Stardust sample-return capsule and is also a primary candidate material for the Mars Science Lander (MSL), the Orion Crew Module, and the SpaceX Dragon vehicle. As part of the heatshield qualification for Orion, physical and thermal properties of virgin and charred PICA were measured, and an ablation and thermal response model was developed. We validated the model by comparing it with recession and temperature data from stagnation arcjet tests conducted over a wide range of stagnation heat flux of 107 to 1102 W/sq cm. The effect of orthotropic thermal conductivity was evident in the thermal response of the arcjet models. In general, model predictions compared well with the data; however, the uncertainty of the recession prediction was greatest for heat fluxes below 200 W/sq cm. More recent MSL testing focused on the low heat flux regime of 45 to 250 W/sq cm. The new results confirm the recession uncertainty, especially for pressures below 6 kPa. In this work we focus on improving the model predictions for MSL and Orion tests below 250 W/sq cm.

Milos, Frank S.↗

NASA NTRSDate not supplied

Using Thermal Desktop to Model the Effects of Plume Heating on MLI

Gateway draws on experience from International Space Station (ISS) and geostationary satellites for many aspects of design, including Multilayer Insulation (MLI) material selection. MLI is used on many external surfaces, some of which can be exposed to high plume heating from visiting vehicle during docking and undocking. Due to Gateway’s smaller size and closer proximity of sensitive hardware to plumes from visiting vehicles, the expected and contingency plume heating loads are higher than those experienced by the ISS. Because of MLI’s low mass and thermal conductivity between layers, high plume heating loads can potentially heat MLI past its thermal limits. MLI is typically modeled as a single node of insulation with a given effective emissivity. This method is not adequate for modeling plume heating impacts because the temperature of each individual layer cannot be determined. Modeling MLI is complicated because there are several layers and the conduction between each layer is undefined. It is further complicated by the variety of material options for MLI and their respective mass, optics, transmissivity, and temperature limits. This paper shows modeling of a MLI blanket exposed to solar and plume heating loads using Thermal Desktop. Several sensitivity studies were run including examining distance between layers, varying effective emissivity, effects of different MLI materials, and plume heating loads and durations.

MLI↗

NASA NTRSDate not supplied

Using Thermal Desktop to Model the Effects of Plume Heating on MLI

Gateway draws on experience from International Space Station (ISS) and geostationary satellites for many aspects of design, including Multilayer Insulation (MLI) material selection. MLI is used on many external surfaces, some of which can be exposed to high plume heating from visiting vehicle during docking and undocking. Due to Gateway’s smaller size and closer proximity of sensitive hardware to plumes from visiting vehicles, the expected and contingency plume heating loads are higher than those experienced by the ISS. Because of MLI’s low mass and thermal conductivity between layers, high plume heating loads can potentially heat MLI past its thermal limits. MLI is typically modeled as a single node of insulation with a given effective emissivity. This method is not adequate for modeling plume heating impacts because the temperature of each individual layer cannot be determined. Modeling MLI is complicated because there are several layers and the conduction between each layer is undefined. It is further complicated by the variety of material options for MLI and their respective mass, optics, transmissivity, and temperature limits. This paper shows modeling of a MLI blanket exposed to solar and plume heating loads using Thermal Desktop. Several sensitivity studies were run including examining distance between layers, varying effective emissivity, effects of different MLI materials, and plume heating loads and durations.

MLI↗

NASA NTRS1993

The influence of thermal inertia on Mars' seasonal pressure variation and the effect of the weather component

Using a Leighton-Murray type diurnal and seasonal Mars thermal model, we found that it is possible to reproduce the seasonal variation in daily-averaged pressures (approximately 680-890 Pa) measured by Viking Lander 1 (VL1), during years without global dust storms, with a standard deviation of less than 5 Pa. In this simple model, surface CO2, frost condensation, and sublimation rates at each latitude are determined by the net effects of radiation, latent heat, and heat conduction in subsurface soil layers. An inherent assumption of our model is that the seasonal pressure variation is due entirely to the exchange of mass between the atmosphere and polar caps. However, the results of recent Mars GCM modeling have made it clear that there is a significant dynamical contribution to the seasonal pressure variation. This 'weather' component is primarily due to large-scale changes in atmospheric circulation, and its magnitude depends somewhat on the dust content of the atmosphere. The overall form of the theoretical weather component at the location of VL1, as calculated by the AMES GCM, remains the same over the typical range of Mars dust opacities.

Wood, S. E.↗

NASA NTRS2008

JWST ISIM Harness Thermal Evaluation

The James Webb Space Telescope (JWST) will be a large infrared telescope with a 6.5-meter primary mirror. Launch is planned for 2013. JWST wl1 be the premier observatory of the next decade serving thousands of astronomers worldwide. The Integrated Science Instrument Module (ISIM) is the unit that will house thc four main JWST instruments. The ISIM enclosure passively cooled to 37 Kelvin and has a tightly managed thermal budget. A significant portion of the ISIM heat load is due to parasitic heat gains from the instrument harnesses. These harnesses provide a thermal path from the Instrument Electronics Control (IEC) to the ISIM. Because of the impact of this load to the ISIM thermal design, understanding the harness parasitic heat gains is critical. To this effect, a thermal test program has been conducted in order to characterize these parasitic loads and verify harness thermal models. Recent parasitic heat loads tests resulted in the addition of a dedicated multiple stage harness radiator. In order for the radiator to efficiently reject heat from the harness, effective thermal contact conductance values for multiple harnesses had to be determined. This presentation will describe the details and the results of this test program.

Kobel, Mark↗

NASA NTRS1983

On the preferential acceleration and heating of solar wind heavy ions

It is pointed out that the properties of solar wind ions heavier than H(+) have presented a puzzle to theorists for some time. The most recent theoretical efforts to explain the observations are considered, taking into account studies conducted by Dusenbery and Hollweg (1981) and Marsch et al. (1982). The first model of a wave-driven, three-fluid, supersonic solar wind is considered. Details of the resonant wave-particle interaction are discussed and the relevant equations for the model are derived. An investigation is conducted of the effects of resonant cyclotron acceleration and heating by a spectrum of nondispersive ion cyclotron waves on the model. It is found that there are serious difficulties with the hypothesis that the resonant cyclotron interaction is responsible for the preferential heating and acceleration of heavy ions in the solar wind. The model presented here is unable to produce the required energization by this mechanism. However, this model should be viewed as an approximate one, subject to possible correction by more advanced calculations.

Isenberg, P. A.↗

NASA NTRS2013

NO PLIF Visualizations of the Orion Capsule in LENS-I

Planar laser-induced fluorescence (PLIF) of nitric oxide (NO) was used to visualize the interaction of reaction-control-system (RCS) jet flows in the wake of a hypersonic capsule reentry vehicle. The tests were performed at the Calspan University at Buffalo Research Center's (CUBRC) LENS-I reflected shock tunnel facility. This was the first application of PLIF to study RCS jets in a large-scale pulsed hypersonic facility. The LENS-I facility allowed RCS jet flows to be studied while varying the flow enthalpy, Reynolds number, angle of attack and jet configuration. The interaction of pitch and roll jets with the flowfield was investigated. Additionally, thin film sensors were used to monitor heat transfer on the surface of the model to detect any localized heating resulting from the firing of the RCS jets. Tests were conducted with the model held at angles of attack of 18deg and 22deg. The nominal Mach number in all tests was 8, while Reynolds number based on model diameter ranged from 2.2x10(exp 6) - 1.5x10(exp 7). Images were processed using the Virtual Diagnostics Interface (ViDI) system developed at NASA Langley Research Center to provide a three-dimensional display of the experimental data.

Combs, C.↗

NASA NTRS1984

Numerical modeling of laser thermal propulsion flows

An review of the problems associated with modeling laser thermal propulsion flows, a synopsis of the status of such models, and the attributes of a successful model are presented. The continuous gaseous hydrogen laser-supported combustion wave (LSCW) thruster, for which a high-energy laser system (preferably space-based) should exist by the time the propulsion technology is developed, is considered in particular. The model proposed by Raizer (1970) is based on the assumptions of one-dimensional flow at constant pressure with heat conduction as the principal heat transfer mechanism. Consideration is given to subsequent models which account for radiative transfer into the ambient gas; provide a two-dimensional generalization of Raizer's analysis for the subsonic propagation of laser sparks in air; include the effect of forward plasma radiation in a one-dimensional model; and attempt a time-dependent (elliptic) solution of the full Navier-Stokes equations for the flow in a simple axisymmetric thruster. Attention is also given to thruster and nozzle flow models and thermodynamic and transport properties.

Mccay, T. D.↗

NASA NTRS1993

Verification of thermal analysis codes for modeling solid rocket nozzles

One of the objectives of the Solid Propulsion Integrity Program (SPIP) at Marshall Space Flight Center (MSFC) is development of thermal analysis codes capable of accurately predicting the temperature field, pore pressure field and the surface recession experienced by decomposing polymers which are used as thermal barriers in solid rocket nozzles. The objective of this study is to provide means for verifications of thermal analysis codes developed for modeling of flow and heat transfer in solid rocket nozzles. In order to meet the stated objective, a test facility was designed and constructed for measurement of the transient temperature field in a sample composite subjected to a constant heat flux boundary condition. The heating was provided via a steel thin-foil with a thickness of 0.025 mm. The designed electrical circuit can provide a heating rate of 1800 W. The heater was sandwiched between two identical samples, and thus ensure equal power distribution between them. The samples were fitted with Type K thermocouples, and the exact location of the thermocouples were determined via X-rays. The experiments were modeled via a one-dimensional code (UT1D) as a conduction and phase change heat transfer process. Since the pyrolysis gas flow was in the direction normal to the heat flow, the numerical model could not account for the convection cooling effect of the pyrolysis gas flow. Therefore, the predicted values in the decomposition zone are considered to be an upper estimate of the temperature. From the analysis of the experimental and the numerical results the following are concluded: (1) The virgin and char specific heat data for FM 5055 as reported by SoRI can not be used to obtain any reasonable agreement between the measured temperatures and the predictions. However, use of virgin and char specific heat data given in Acurex report produced good agreement for most of the measured temperatures. (2) Constant heat flux heating process can produce a much higher heating rate than the radiative heating process. The results show that heating rates of 125 C/s (225 F/s) can be achieved. (3) The electrical resistance of the FM 5055 samples were about 150 Omega in the virgin state, and decreased to about 35 Omega when charred. A reliable scheme must be developed to electrically insulate the composite from the heater foil in order to prevent any current leakage into the sample which can result in volumetric heating of the char zone of the composite.

Keyhani, M.↗

NASA NTRS1971

Models of the Venus ionosphere

Venus daytime ionospheric models using electron, ion and neutral gas heat conduction with momentum and chemical equations for charged particle densities

Bauer, S. J.↗

NASA NTRS1991

Heat transfer in rotating serpentine passages with trips normal to the flow

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

Wagner, J. H.↗

NASA NTRS1991

Heat transfer in rotating serpentine passages with trips normal to the flow

Experiments were conducted to determine the effects of buoyancy and Coriolis forces on heat transfer in turbine blade internal coolant passages. The experiments were conducted with a large scale, multipass, heat transfer model with both radially inward and outward flow. Trip strips on the leading and trailing surfaces of the radial coolant passages were used to produce the rough walls. An analysis of the governing flow equations showed that four parameters influence the heat transfer in rotating passages: coolant-to-wall temperature ratio, Rossby number, Reynolds number, and radius-to-passage hydraulic diameter ratio. The first three of these four parameters were varied over ranges which are typical of advanced gas turbine engine operating conditions. Results were correlated and compared to previous results from stationary and rotating similar models with trip strips. The heat transfer coefficients on surfaces, where the heat increased with rotation and buoyancy, varied by as much as a factor of four. Maximum values of the heat transfer coefficients with high rotation were only slightly above the highest levels obtained with the smooth wall model. The heat transfer coefficients on surfaces, where the heat transfer decreased with rotation, varied by as much as a factor of three due to rotation and buoyancy. It was concluded that both Coriolis and buoyancy effects must be considered in turbine blade cooling designs with trip strips and that the effects of rotation were markedly different depending upon the flow direction.

Wagner, J. H.↗

NASA NTRS1993

Preliminary SP-100/Stirling heat exchanger designs

Analytic modeling of several heat exchanger concepts to couple the SP-100 nuclear reactor primary lithium loop and the Space Stirling Power Convertor (SSPC) was performed. Four 25 kWe SSPC's are used to produce the required 100 kW of electrical power. This design work focused on the interface between a single SSPC and the primary lithium loop. Manifolding to separate and collect the four channel flow was not modeled. This work modeled two separate types of heat exchanger interfaces (conductive coupling and radiative coupling) to explore their relative advantages and disadvantages. The minimum mass design of the conductively coupled concepts was 18 kg or 0.73 kg/kWe for a single 25 kWe convertor. The minimum mass radiatively coupled concept was 41 kg or 1.64 kg/kWe. The direct conduction heat exchanger provides a lighter weight system because of its ability to operate the Stirling convertor evaporator at higher heat fluxes than those attainable by the radiatively coupled systems. Additionally the conductively coupled concepts had relatively small volumes and provide potentially simpler assembly. Their disadvantages were the tight tolerances and material joining problems associated with this refractory to superalloy interface. The advantages of the radiatively coupled designs were the minimal material interface problems.

Schmitz, Paul↗

NASA NTRS1975

Heat transfer tests of an 0.006-scale thin-skin space shuttle thermocouple model (41-OTS) in the Langley Research Center unitary plan wind tunnel at M equals 3.7 (IH16)

The results are presented of supersonic heat transfer tests performed on the .006 scale space shuttle vehicle model (41-OTS) in the Langley Research Center Unitary Plan Wind Tunnel. These tests were conducted to parametrically investigate ascent heating of the integrated vehicle and its components. The tests were conducted at a nominal Mach number of 3.7 and Reynolds numbers per foot of 2 and 5 million. The model configurations investigated were the integrated vehicle and each component alone (i.e. orbiter, tank and SRB). All the configurations were run with and without transition strips and through an angle of attack range of 0 deg to minus 5 deg with the exception of the SRB which was tested through an angle of attack range of minus 5 deg to 90 deg. The heat transfer data were obtained from 223 iron constantan thermocouples attached to stainless steel thin-skin areas of the model.

Walstad, D. G.↗

NASA NTRS2003

Active Control of Interface Shape During the Crystal Growth of Lead Bromide

A thermal model for predicting and designing the furnace temperature profile was developed and used for the crystal growth of lead bromide. The model gives the ampoule temperature as a function of the furnace temperature, thermal conductivity, heat transfer coefficients, and ampoule dimensions as variable parameters. Crystal interface curvature was derived from the model and it was compared with the predicted curvature for a particular furnace temperature and growth parameters. Large crystals of lead bromide were grown and it was observed that interface shape was in agreement with the shape predicted by this model.

Duval, W. M. B.↗

NASA NTRS2001

Effective Thermal Conductivity of High Porosity Open Cell Nickel Foam

The effective thermal conductivity of high-porosity open cell nickel foam samples was measured over a wide range of temperatures and pressures using a standard steady-state technique. The samples, measuring 23.8 mm, 18.7 mm, and 13.6 mm in thickness, were constructed with layers of 1.7 mm thick foam with a porosity of 0.968. Tests were conducted with the specimens subjected to temperature differences of 100 to 1000 K across the thickness and at environmental pressures of 10(exp -4) to 750 mm Hg. All test were conducted in a gaseous nitrogen environment. A one-dimensional finite volume numerical model was developed to model combined radiation/conduction heat transfer in the foam. The radiation heat transfer was modeled using the two-flux approximation. Solid and gas conduction were modeled using standard techniques for high porosity media. A parameter estimation technique was used in conjunction with the measured and predicted thermal conductivities at pressures of 10(exp -4) and 750 mm Hg to determine the extinction coefficient, albedo of scattering, and weighting factors for modeling the conduction thermal conductivity. The measured and predicted conductivities over the intermediate pressure values differed by 13%.

Sullins, Alan D.↗

NASA NTRS1974

Heat transfer model for predicting squib ignition times

A squib ignition model based on transient heat condition from the hot bridgewire to the pyrotechnic is described. No Arrhenius-type chemical reaction is included. Instead, a thermal contact resistance is postulated to exist between the hot bridgewire and the pyrotechnic. Ignition is assumed to occur when a 2.5 micron layer of pyrotechnic next to the bridgewire reaches a characteristic ignition temperature for that pyrotechnic. This model was applied to the JPL squib, which uses a 50 micron (0.002-in.) diameter Tophet A bridgewire to ignite a boron, potassium perchlorate mix. A computer program was utilized that solves the transient heat condition problem with the boundary conditions stipulated by the model. The thermal contact conductance at the interface was determined by trial and error so that the experimentally determined ignition time for one firing condition would be properly predicted by the model. The agreement was quite good for tests run between -129 C and +93.3 C at current levels of 3.5 and 5 A. Axial heat conduction along the bridgewire is shown to be negligible.

Sernas, V.↗