SEARCH · Engineering Papers

Results for “HIGH TEMPERATURE GAS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

NASA NTRS1981

The ionization state in a gas with a non-Maxwellian electron distribution

The inferred degree of ionization of a gas is often used in astrophysics as a diagnostic of the gas temperature. In the solar transition region and corona, in the outer atmospheres of cool stars, and in some portions of the interstellar medium), photoionization can be neglected, and the ionization state is fixed by the balance between ion-electron collisional ionization and dielectronic and/or radiative recombination. Under these conditions, higher degrees of ionization result from higher energy ion-electron collisions which are common in a high temperature gas. Actually, ionization occurs through collisions with electrons that have kinetic energies greater than the ionization potential of the given ion, and so the ionization rate depends on to the number of such high-energy electrons in the tail of the electron velocity distribution. High-velocity electrons move across large distances between effective coulomb collisions, and, in a strong temperature or density gradient, the tail can be overpopulated relative to Maxwell-Boltzmann distribution of equivalent energy density. Thus, the ionization rate can also be greatly increased. These effects for a parameterized form of the electron distribution function with an enhanced high-velocity tail, namely the kappa distribution are illustrated.

Owocki, S. P.↗

DOE OSTI2020

Coupling of Pronghorn and RELAP-7 for a Pebble Bed Reactor

High temperature gas cooled reactors (HTGR) are a candidate for timely Gen-IV reactor technology deployment because of high technology readiness and walk-away safety. Among HTGRs, pebble bed reactors (PBRs) have attractive features such as low excess reactivity and online refueling. Pebble bed reactors pose unique challenges to analysts and reactor designers such as continuous burnup distribution depending on pebble motion and recirculation, radiative heat transfer across a variety of gas-filled gaps, and long design basis transients such as pressurized and depressurized loss of forced circulation. Modeling and simulation is essential for both the PBR’s safety case and design process. In order to verify and validate the new generation codes the Nuclear Energy Agency (NEA) Data bank provide a set of benchmarks data together with solutions calculated by the participants using the state of the art codes of that time. An important milestone to test the new PBR simulation codes is the OECD NEA PBMR-400 benchmark which includes thermal hydraulic and neutron kinetic standalone exercises as well as coupled exercises and transients scenarios. In this work, the reactor multiphysics code MAMMOTH and the thermal hydraulics code Pronghorn, both developed by the Idaho National Laboratory (INL) within the multiphysics object-oriented simulation environment (MOOSE), have been used to solve Phase 1 exercises 1 and 2 of the PBMR-400 benchmark. The steady state results are in agreement with the other participants’ solutions demonstrating the adequacy of MAMMOTH and Pronghorn for simulating PBRs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2020

Development and Test of High Temperature Surface Acoustic Wave Gas Sensors

The demand for sensors in hostile environments, such as power plant environments, aerospace environments, oil and gas extraction, and high-temperature metallurgy environments, has risen over the past decades in a continuous attempt to increase process control, improve energy and process efficiency in production, reduce operational and maintenance costs, increase safety, and perform condition-based maintenance in equipment and structures operating in high-temperature harsh-environment conditions. The increased reliability, improved performance, and development of new sensors and networks with a multitude of components, especially wireless networks, are the target for operation in harsh environments. Gas sensors, in particular H2 sensors, operating above 200 C are required in the instrumentation, process control and general safety of a number of industries including coal, natural gas, and nuclear power generation facilities, the aerospace and automotive industries, metallurgical production and defense-related applications. The surface acoustic wave (SAW) platform is a particularly promising option for high-temperature, harsh-environment gas sensing applications since the platform exhibits advantages, such as battery-free and wireless operation, small size, possibility for scale production using well-developed technologies from the semiconductor industry, and low cost of installation and operation. In this work, one-port SAW resonators (SAWRs) operating along five different orientations on a commercially available langasite (LGS) wafer employing Pt-Al2O3 electrodes and reflectors were designed, fabricated, and used as high-temperature H2 sensors. Two of the selected orientations were predicted and confirmed to have temperature-compensated operation above 150 C. A gas sensor test setup was developed, capable of gas cycling between N2, O2 and N2/H2 mixtures under extended high-temperature periods (up to 650 C for over 20 hours). Thin film Pt-Al2O3 was used as the electrode material for the transducers and reflectors capable of high-temperature operation, and also as H2 sensing film. In addition, yttria-stabilized zirconia (YSZ) thin films with Pt decoration were tested as sensing films aimed to enhance the SAWR sensor response to H2. The SAW devices were monitored in excess of 1700 hours in real-time during gas cycling sequences up to 600 C, leading to the following findings: i) the Pt-Al2O3 electrodes performed better for H2 sensing than the Pt-decorated YSZ sensing film, showing as much as 50% higher frequency variation response in the 200 C to 400 C range; ii) different crystallographic orientations operating on the same LGS wafer experienced different responses to H2 exposures up to 500 C; iii) the surface oxidation state of the SAWR sensors was shown to have an important impact on subsequent H2 exposure responses. In addition, a sensor system employing two LGS SAWRs, aligned along two different orientations, has been developed to simultaneously determine H2 presence and temperature. Finally, wireless interrogation of a SAWR sensor was successful within the gas cycling test fixture, and successful wireless H2 detection was achieved above 400 C.

Ayes Moncada, Armando↗

NASA NTRS1990

Einstein Observatory coronal temperatures of late-type stars

The results are presented of a survey of the coronal temperatures of late-type stars using the Einstein Observatory IPC. The spectral analysis shows that the frequently found one- and two-temperature descriptions are mainly influenced by the SNR of the data and that models using continuous emission measure distributions can provide equally adequate and physically more meaningful and more plausible descriptions. Intrinsic differences in differential emission measure distributions are found for four groups of stars. M dwarfs generally show evidence for high-temperature gas in conjunction with lower-temperature material, while main-sequence stars of types F and G have the high-temperature component either absent or very weak. Very hot coronae without the lower-temperature component appearing in dwarf stars are evident in most of the giant stars studied. RS CVn systems show evidence for extremely hot coronae, sometimes with no accompanying lower-temperature material.

Schmitt, J. H. M. M.↗

DOE OSTI2020

Initial Evaluation of Microreactor Disposition Options

The United States Department of Energy is supporting the U.S advanced reactor industry through funding, legislation and regulatory development to actively pursue several microreactor design concepts. The Idaho National Laboratory (INL) is strategically positioned to support demonstration of microreactor technology in the next three to five years. This report provides and initial evaluation of the disposition options for microreactor spent nuclear fuel (SNF) generated as part of the microreactor technology demonstration program. Currently available information constitutes the basis for the options identified and discussions thereof. In the absence of detailed microreactor design information, assumptions were made to facilitate the identification of disposition options Particulars pertaining to any component of an identified disposition pathway are naturally highly microreactor design specific and in general such details are not provided. The diverse nature of potential microreactor SNF is reflected in the diverse nature of DOE owned SNF stored at INL. Therefore, it is anticipated that DOE currently stores and manages fuels that can serve as analogs for most microreactor fuel concepts. As such disposition options for microreactor SNF are expected to be much the same as that for these existing fuels. Two generic microreactor concepts have been selected for the purposes of this options assessment. The selected reactor concepts are a tristructural isotropic (TRISO) fueled high temperature gas reactor concept and a sodium/potassium bonded heat pipe reactor with uranium oxide fuel. Both concepts are assumed to be using high-assay low enriched uranium (HALEU) as the initial fuel composition. Interim storage, treatment and neutralization, material recovery, packaging and extended dry storage options are identified these reactors. The disposition options include existing INL facilities and capabilities and new facilities and capabilities developed as part of the microreactor program or as part of DOE's overall strategy for the eventual transfer of all SNF at INL to a permanent repository.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Materials Challenges and Opportunities for Energy Generation, Conversion, Delivery, and Storage (Applied Energy Tri-Laboratory Consortium Workshop Report)

This report documents the outcomes of the Tri-Laboratory Materials Workshop that was held July 31 and August 1, 2019 to begin addressing the needs, opportunities, and challenges associated with the development, fabrication, and testing of the needed materials and components for integrated hybrid energy systems (i.e., incorporating nuclear, fossil, and renewables for electric and thermal applications). This was accomplished by assembling the research program leads and principal investigators at Idaho National Laboratory (INL), National Energy Technology Laboratory (NETL), and National Renewable Energy Laboratory (NREL), who support the research and development of new technology and system integration. The team then identified and prioritized key materials development needs. This effort was intended to enhance communications and synergy among the Tri-Lab partners. Advanced functional and structural materials are central to transformative energy technologies for energy generation, conversion, delivery, and storage. With that in mind, the workshop focused on identifying and assessing the foundational materials research needs at both the basic and applied levels. Materials challenges include the ability to withstand harsh environments, such as high temperatures and pressures, corrosion, oxidation, or irradiation while maintaining flexible mission profiles and long service lifespans. Advanced energy system material challenges and needs range from materials for the capture, upgrading/concentration, storage, and delivery of low-grade heat to materials for high temperature environments that involve liquid metals, molten salt, and very high temperature gas heat delivery and storage systems. Material improvements are needed for hybrid energy systems due to accelerated corrosion and stress-fatigue failure of materials and equipment, which results from increased frequency and amplitude of thermal, mechanical, and electrical cycling of systems components. Multifunctional materials are needed for high temperature solid-oxide fuel cells, advanced electrochemical reactors, and in-process separation. Relative to materials manufacturing, application of advanced additive and subtractive methods need to be understood to develop both thin-layer homogenous materials and materials of graded composition. Materials modeling and machine learning will be critical to accelerate the design and production of power electronics, and nuclear reactor materials and fuel, as well as to gain an understanding of beneficial materials phenomena or deleterious microstructure evolution. There is also a need for standardized models, computational structures, data reporting protocols and modeling tools across the three laboratories. This would allow consistent results, analysis, and data sharing. Combining computational capabilities between the three laboratories (e.g., hardware, software) would greatly increase computational capabilities and throughput. The workshop identified the need for laboratories to anticipate and address problems that will occur during scale-up. Laboratory work must connect with industry to ensure that research focuses on processes that are scalable and marketable. Industry input and perspective are essential to guide laboratory research to meet these requirements and deploy new technology in industrial demonstrations. Another aspect of scale-up is the integration of multiple systems since new challenges often arise at the subsystem interfaces. Establishing a scale-up manufacturing demonstration/pilot plant, potentially as an industrial user facility, would be beneficial to the laboratories and industry. That modular scale-up manufacturing demonstration/pilot plant would allow researchers to find and resolve interface problems that cannot be identified by focusing only on individual parts. Communication exchanges among the organizers, attendees, and workshop survey responses indicate that the workshop was successful in achieving its goal to identify key technology gaps and research needs. Strong positive feedback was received on the sharing of ideas, capabilities, talent, and passion to move forward on the materials-related action items.

36 MATERIALS SCIENCE↗

DOE OSTI2021

AGR-5/6/7 Fuel Fabrication Report

The U.S. Department of Energy Office of Nuclear Energy (DOE NE) and the Idaho National Laboratory (INL) Advanced Reactor Technologies (ART) Advanced Gas Reactor (AGR) Fuel Development and Qualification program (referred to as AGR Fuel program hereafter) are pursuing qualification of tristructural isotropic (TRISO) coated particle fuel for use in high temperature gas cooled reactors (HTGRs). The AGR Fuel program was established to provide a fuel qualification data set in support of the licensing and operation of an HTGR. BWX Technologies Nuclear Operations Group (BWXT-NOG) was subcontracted to fabricate the fuel for the AGR program. Several investments and innovations were realized in preparation to fabricate fuel for the AGR-5/6/7 irradiation experiments that brought fuel fabrication fully out of the laboratory and into engineering-scale operations. These included: • Increased the kernel fabrication line capacity and uniformity • Upgraded ancillary support equipment and processes for the tristructural isotropic (TRISO) coating furnace • Demonstrated efficient production of the matrix precursor powder by dry jet milling of co mingled components • Demonstrated an engineering-scale method for quick and efficient overcoating TRISO particles with the matrix precursor • Demonstrated an automated, multi cavity compacting system with a volumetric feed system • Demonstrated a combined-cycle thermal treatment furnace These changes increased production rates of some of these processes by an order of magnitude or more while eliminating the use of flammable solvents, multiple grinding and sorting operations, and the weighing out of individual die charges. Three fuel kernel lots were fabricated for production of the fuel for AGR-5/6/7. The initial lot (J52R-16-39316) was certified to fuel specifications but was not used because the kernels had a high fraction of internal fissures that caused an unacceptable fraction of the kernels to fragment when charged to the coating furnace where the TRISO coating would be deposited. Fragmented kernels increased the dispersed uranium in the particles and produced a worrisome fraction of dimpled particles with an elevated probability of in-pile failure. After some efforts to identify the cause of the fissure formation, two additional lots were produced with much lower fissure fractions, J52R-16-69317 and 69318. The latter kernel lot was a backup to the first and was not needed. Multiple kernel batches were composited to form each of the lots so as to simulate a commercial-scale operation where kernel batches would also be composited. Multiple TRISO coating runs were performed and the product characterized so that several could be composited into a TRISO lot. TRISO lot J52R-16-98005 conformed to all fuel specifications except the mean outer pyrocarbon (OPyC) layer thickness was thinner than specified. Furthermore, it was determined that the TRISO lot had a dispersed uranium fraction (DUF) that might result in the compacts not meeting the DUF specification. A review of the role of the OPyC layer and consequences of the DUF by the Technical Coordination Team and INL concluded that the fuel was acceptable for use in the AGR-5/6/7 irradiation experiment. The TRISO particles were overcoated with the matrix precursor that had been produced in a jet-milling operation. The overcoating was performed in equipment originally designed to coat pharmaceuticals. The overcoating process performed well; producing highly spherical and uniform overcoats requiring little upgrading and no recycle or rework. TRISO particles were overcoated with the matrix precursor to achieve nominal volumetric packing fractions (PFs) of TRISO particles of 25% and 40% for the irradiation experiments. The 40% PF compacts occupy the first and fifth test capsule in the test train while the inner three capsules are loaded with 25% PF compacts. The resinated graphite matrix precursor powder was a derivative of the German A3-27 matrix formulation, which differs from previous AGR irradiation campaigns that used an A3-3 formulation. Jet milling of the matrix powder precursor produced a finer mean graphite particle size than the milling operations used for the A3-3 matrix powder precursor. Changes made in the matrix formula and equipment yielded compacts with significantly higher matrix density than was attained in previous AGR irradiation campaigns. The changes in the matrix formulation and the means of milling the powders also complicated resolution of the three fuel compact defect fractions, DUF, exposed kernel fraction (EKF), and the silicon carbide defect fraction (SDF). Characterization data from BWXT-NOG had some anomalous results, so samples of the fuel compacts and overcoated TRISO particles were also analyzed by Oak Ridge National Laboratory (ORNL) to ensure that the defect fractions were accurately characterized.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

An Experimental and Theoretical Examination of Air Ingress Rates During Small- and Medium-Break Air Ingress Accidents

Here, air ingress measurements using the 1/20th-scaled Helium Air Ingress gas Reactor Experiment (HAIRE) facility show key geometric variables of interest and their effect on air ingress in small- and medium-sized breaks in High Temperature Gas cooled Reactors. These variables include but are not limited to break diameter, break angle, and break wall thickness. Differing wall thicknesses for the same break diameter can have order-of-magnitude changes to the air ingress rate, which is a key figure of merit in the air ingress accident scenario. Additionally, different break sizes can change the importance of the angle in the break scenario. With smaller breaks, the flow will not transition from intermittent flow, to countercurrent flow, to diffusive flow as the break rotates from vertically upward toward vertically downward. This would lead to less variability with smaller breaks, which in turn would make the accident scenario more predictable for smaller-sized breaks.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NASA NTRS1997

OMC Compressor Case

This report summarizes efforts expended in the development of an all-composite compressor case. Two pre-production units have been built, one utilizing V-CAP and one utilizing AFR-700B resin systems. Both units have been rig tested at elevated temperatures well above design limit loads. This report discusses the manufacturing processes, test results, and Finite Element Analysis performed. The V-CAP unit was funded by NASA-Lewis Research Center in 1994 under contract number NAS3- 27442 for Development of an All-Composite OMC Compressor Case. This contract was followed by an Air Force study in 1996 to build and identical unit using the AFR-700B resin system in place of the V-CAP system. The second compressor case was funded under U.S. Air Force contract F33615-93-D-5326, Advanced Materials for Aerospace Structures Special Studies (AMAS3), Delivery Order 0021 entitled "Advanced Polymeric Composite Materials and Structures Technology for Advanced High Temperature Gas Turbine Engines.' Initial studies using the V-CAP resin system were undertaken in 1993 under a NASA Lewis contract (NAS3-26829). A first prototype unit was developed in a joint program between Textron-Lycoming (now Allied Signal) and Brunswick (now Lincoln Composites). This unit included composite end closures using low density, high temperature molded end closures. The units was similar in size and shape to a titanium case currently used on the PT-21 0 engine and was funded as part of the integrated High Performance Turbine Engine Technology (EHPTET) initiative of DOD and NASA.

Humphrey, W. Donald↗

DOE OSTI2025

JCZ3: An Equation of State Based on the Exponential-Six Intermolecular Potential – Update: Formulation

This report presents a comprehensive analysis of the JCZ3 equation of state (EOS) as implemented in the TIGER code, focusing on its thermodynamic framework, mathematical formulations, and implications for modeling gas phase behavior under varying conditions. Overall, the report affirms the TIGER code's foundational robustness and its potential as a valuable tool for simulating high-pressure, high-temperature gas mixtures, while also highlighting areas for further refinement and validation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

NASA NTRS2001

Laser High-Cycle Thermal Fatigue of Pulse Detonation Engine Combustor Materials Tested

Pulse detonation engines (PDE's) have received increasing attention for future aerospace propulsion applications. Because the PDE is designed for a high-frequency, intermittent detonation combustion process, extremely high gas temperatures and pressures can be realized under the nearly constant-volume combustion environment. The PDE's can potentially achieve higher thermodynamic cycle efficiency and thrust density in comparison to traditional constant-pressure combustion gas turbine engines (ref. 1). However, the development of these engines requires robust design of the engine components that must endure harsh detonation environments. In particular, the detonation combustor chamber, which is designed to sustain and confine the detonation combustion process, will experience high pressure and temperature pulses with very short durations (refs. 2 and 3). Therefore, it is of great importance to evaluate PDE combustor materials and components under simulated engine temperatures and stress conditions in the laboratory. In this study, a high-cycle thermal fatigue test rig was established at the NASA Glenn Research Center using a 1.5-kW CO2 laser. The high-power laser, operating in the pulsed mode, can be controlled at various pulse energy levels and waveform distributions. The enhanced laser pulses can be used to mimic the time-dependent temperature and pressure waves encountered in a pulsed detonation engine. Under the enhanced laser pulse condition, a maximum 7.5-kW peak power with a duration of approximately 0.1 to 0.2 msec (a spike) can be achieved, followed by a plateau region that has about one-fifth of the maximum power level with several milliseconds duration. The laser thermal fatigue rig has also been developed to adopt flat and rotating tubular specimen configurations for the simulated engine tests. More sophisticated laser optic systems can be used to simulate the spatial distributions of the temperature and shock waves in the engine. Pulse laser high-cycle thermal fatigue behavior has been investigated on a flat Haynes 188 alloy specimen, under the test condition of 30-Hz cycle frequency (33-msec pulse period and 10-msec pulse width including a 0.2-msec pulse spike; ref. 4). Temperature distributions were calculated with one-dimensional finite difference models. The calculations show that that the 0.2-msec pulse spike can cause an additional 40 C temperature fluctuation with an interaction depth of 0.08 mm near the specimen surface region. This temperature swing will be superimposed onto the temperature swing of 80 C that is induced by the 10-msec laser pulse near the 0.53-mm-deep surface interaction region.

Zhu, Dong-Ming↗

NASA NTRS1994

Theoretical studies of a molecular beam generator

We consider the problem of modeling a high temperature diatomic gas N2 flowing through a converging-diverging high expansion nozzle. The problem is modeled in two ways. The first model uses a single temperature with variable specific heats as functions of this temperature. For the second model we assume that the various degrees of freedom all have a Boltzmann population distribution which means that each degree of freedom has its own temperature and consequently each system state can be characterized by these temperatures. This suggests the formulation of a second model with a vibrational degree of freedom as having its own temperature along with a rotational-translational degree of freedom with its own temperature. Initially the vibrational degree of freedom is excited by heating the gas to a high temperature. As the high temperature gas expands through the nozzle throat there is a sudden drop in the rotational-translational temperature along with a finite relaxation time for the vibrational degree of freedom to achieve equilibrium with the rotational-translational degree of freedom. That is, the temperature change that occurs when the N2 gas passes through the nozzle throat is so great that the changes in the vibrational degree of freedom lags behind the rotational-translational energy changes. The resulting relaxation time is finite. It is in this context that the term nonequilibrium is used. That is, the term nonequilibrium denotes the fact that the energy content of the various degrees of freedom are characterized by two temperatures. We neglect any chemical reactions resulting from the high temperatures which could also add nonequilibrium effects. We develop the basic equations for the two models in various forms in order to check the derivations with other sources. The final form which is solved numerically consists of the scaled equations in a conservative dimensionless form.

Heinbockel, John H.↗

DOE OSTI2020

An Experimental and Theoretical Study of the High Temperature Reactions of the Four Butyl Radical Isomers

The high temperature gas phase chemistry of the four butyl radical isomers (n-butyl,sec-butyl, iso-butyl, andtert-butyl) was investigated in a combined experimental and theoretical study. Organic nitrites were used as convenient and clean sources of each of the butyl radical isomers. Rate coefficients for dissociation of each nitrite were obtained experimentally and are at, or close to, the high pressure limit. Low pressure experiments were performed in a diaphragmless shock tube with laser schlieren densitometry at post-shock pressures of 65, 130, and 260 Torr and post-shock temperatures of 700-1000 K. Additional experiments were conducted with iso-butyl radicals at 805 K and 8.7 bar to elucidate changes in mechanism at higher pressures. These experiments were performed in a miniature shock tube with synchrotron-based photoionization mass spectrometry. The mass spectra confirmed that scission of the O-NO bond is the primary channel by which the precursors dissociate, but they also provided evidence of a minor channel (<7.7%) through HNO loss and formation of an aldehyde. These high pressure experiments were also used to determine the disproportionation/recombination ratio for iso-butyl radicals as 0.3. Reanalysis of the lower-temperature literature and the present data yielded rate constants for the disproportionation reaction, iso-butyl + iso-butyl = iso-butene + iso-butane. A chemical kinetics model was developed for the reactions of the butyl isomers that included new paths for highly energized adducts. These adducts are formed by the addition of H, CH 3 or C 2 H 5 to the butyl radicals. Accompanying theoretical investigations show that chemically activated pathways are competitive with stabilization of the adduct by collision under the conditions of the laser schlieren experiments. These calculations also show that at 10 bar and T< 1000 K stabilization is the only important reaction, but at higher temperatures, even at 10 bar, chemically activated product channels should also be considered. Branching fractions and rate coefficients are presented for these reactions. Furthermore, this study also highlights the importance of the radical structure for determining branching ratios for disproportionation and recombination of alkyl radicals, and these were facilitated by theoretical calculations of recombination rate coefficients for the four butyl radical isomers. Overall, the results reveal previously unknown features of butyl radical chemistry under conditions that are relevant to a wide range of applications and reaction mechanisms are presented that incorporate pressure dependent rate coefficients for the key steps.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1995

Nozzle flow with vibrational nonequilibrium

This research concerns the modeling and numerical solutions of the coupled system of compressible Navier-Stokes equations in cylindrical coordinates under conditions of equilibrium and nonequilibrium thermodynamics. The problem considered was the modeling of a high temperature diatomic gas N2 flowing through a converging-diverging high expansion nozzle. The problem was modeled in two ways. The first model uses a single temperature with variable specific heats as functions of this temperature. For the second model we assume that the various degrees of freedom all have a Boltzmann distribution and that there is a continuous redistribution of energy among the various degrees of freedom as the gas passes through the nozzle. Each degree of freedom is assumed to have its own temperature and, consequently, each system state can be characterized by these temperatures. This suggests that formulation of a second model with a vibrational degree of freedom along with a rotational-translation degree of freedom, each degree of freedom having its own temperature. Initially the vibrational degree of freedom is excited by heating the gas to a high temperature. As the high temperature gas passes through the nozzle throat there is a sudden drop in temperature along with a relaxation time for the vibrational degree of freedom to achieve equilibrium with the rotational-translation degree of freedom. That is, we assume that the temperature change upon passing through the throat is so great that the changes in the vibrational degree of freedom occur at a much slower pace and consequently lags behind the rotational-translational energy changes. This lag results in a finite relaxation time. In this context the term nonequilibrium is used to denote the fact that the energy content of the various degrees of freedom are characterized by two temperatures. We neglect any chemical reactions which could also add nonequilibrium effects. We develop the energy equations for the nonequilibrium model from first principles. The resulting equations, which model the nozzle flow, can be expressed in various forms. In most forms the resulting equations are coupled systems of nonlinear partial differential equations subject to certain boundary conditions. To solve the resulting coupled system of nonlinear partial differential equations, several numerical techniques were investigated: (1) the explicit MacCormack method, (2) the explicit-implicit MacCormack method, (3) the method of operator splitting, (4) factorization schemes, and (5) the Steger-Warming scheme.

Heinbockel, J. H.↗

DOE OSTI2021

High Temperature Acclimation of Leaf Gas Exchange, Photochemistry, and Metabolomic Profiles in Populus trichocarpa

High temperatures alter the thermal sensitivities of numerous physiological and biochemical processes that impact tree growth and productivity. Foliar and root applications of methanol have been implicated in plant acclimation to high temperature via the C 1 pathway. Here, we characterized temperature acclimation at 35°C of leaf gas exchange, chlorophyll fluorescence and extractable metabolites of potted Populus trichocarpa saplings and examined potential influences of mM concentrations of methanol added during soil watering over a two-month period. Relative to plants grown under the low growth temperature (LGT), high growth temperature (HGT) plants showed a suppression of leaf water use and carbon cycling including transpiration (E), net photosynthesis (P n ), an estimate of photorespiration (R p ), and dark respiration (R d ), attributed to reductions in stomatal conductance and direct negative effects on gas exchange and photosynthetic machinery. In contrast, HGT plants showed an upregulation of non-photochemical quenching (NPQ t ), the optimum temperature for ETR, and leaf isoprene emissions at 40°C. A large number of metabolites (867) were induced under HGT, many implicated in flavonoid biosynthesis highlighting a potentially protective role for these compounds. Methanol application did not significantly alter leaf gas exchange but slightly reduced the suppression of R d and R p by the high growth temperature while slightly impairing ETR, Fv’/Fm’, and q p . However, we were unable to determine if soil methanol was sufficiently taken up by the plant to have a direct effect on foliar processes. A small number of extracted leaf tissue metabolites (55 out of 10,015) showed significantly altered abundances under LGT and methanol treatments relative to water controls, and this increased in compound number (222) at the HGT. The results demonstrate the large physiological and biochemical impacts of high growth temperature on poplar seedlings and highlights the enhancement of the optimum temperature of ETR as a rapid thermal acclimation mechanism. Finally, although no large effect on leaf physiology was observed, the results are consistent with methanol both impairing photochemistry of the light reactions via formaldehyde toxicity, and stimulating photosynthesis and dark respiration through formate oxidation to CO 2 .

59 BASIC BIOLOGICAL SCIENCES↗

NASA NTRS1992

Comparison of methodologies for describing relaxation in nonequilibrium gaseous systems

The heat transfer process in hypervelocity vehicles is dominated by nonequilibrium gas dynamics. One model used in computational fluid dynamics (CFD) codes to predict hypervelocity heat transfer is the 'two-temperature' model. An analysis has been made to test the validity of the two-temperature model for predicting another nonequilibrium phenomenon, sound absorption and deviation of signal speed in a high temperature gas. It is found that the two temperature model's prediction capabilities degenerate with increasing temperature. These results are felt to have significance concerning the two-temperature's ability to predict heat transfer in hypervelocity flows.

Schreiber, Willard C.↗

DOE OSTI2021

Analysis and Design for Irradiation of High Power TRISO Fuel Compact Specimens in HFIR

Tristructural isotropic (TRISO) fuel is being proposed for use in several high-temperature advanced reactor concepts because of its structural integrity under high operating temperatures and burnup. One of these advanced reactor concepts is the Kairos Power fluoride salt-cooled high-temperature reactor (KP- FHR) under development by Kairos Power, LLC. Previous TRISO irradiation experiments were focused on qualification for high-temperature gas reactors (HTGRs), which have higher operating temperatures but lower particle powers than the KP-FHR design. To study the performance of TRISO fuel designed for HTGRs under prototypical FHR conditions, a set of experiments was designed using the MiniFuel irradiation vehicle at the Oak Ridge National Laboratory’s (ORNL) High Flux Isotope Reactor (HFIR). The experiments will irradiate 30 TRISO-containing carbon matrix compacts at inner small vertical experiment facilities in HFIR. Each compact will contain 20 TRISO particles (600 particles total) developed for HTGRs, consisting of either 14% enriched uranium dioxide uranium carbide, naturally enriched uranium dioxide, uranium carbide, or 9.6% enriched uranium dioxide fuel kernels with time- and volume-averaged silicon carbide layer temperatures between 500 and 900°C. This report summarizes the vehicle designs that have been developed, as well as the neutronic and thermal analyses completed for these irradiation experiments. These analyses show that MiniFuel compact irradiation is a versatile experiment that can be used to study a range of TRISO particle powers and fuel types while providing reasonable separation of burnup and temperature effects.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS2019

Gas Turbine Energy Conversion Systems for Lunar and Planetary Nuclear Power Plants Including Ground Based Applications Using LiFTR "Liquid Fluoride Thorium Reactor" Technology

The background and motivation for this presentation is the Advanced Nuclear Power named in Energy Policy Act of 2005 (Gen IV Nuclear Systems Initiative), Thorium Energy Independence & Security Act of 2008 (S.3680), Gen IV Candidate Advanced Nuclear Power Plants, and high temperature gas turbine power plants offer large thermal efficiency improvement over steam plants.

Juhasz, Albert J.↗