Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Grain boundary structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Microstructural effects on the room and elevated temperature low cycle fatigue behavior of Waspaloy

Longitudinal specimens of Waspaloy containing either coarse grains with small gamma or fine grains with large gamma were tested in air at a frequency of 0.33 Hz or 0.50 Hz. The coarse grained structures exhibited planar slip on (III) planes and precipitate shearing at all temperatures. Cracks initiated by a Stage 1 mechanism and propagated by a striation forming mechanism. At 700 C and 800 C, cleavage and intergranular cracking were observed. Testing at 500 C, 700 C, and 800 C caused precipitation of grain boundary carbides. At 700 C, carbides precipitated on slip bands. The fine grained structures exhibited planar slip on (111) planes. Dislocations looped the large gamma precipitates. This structure led to stress saturation and propagation was observed. Increasing temperatures resulted in increased specimen oxidation for both heat treatments. Slip band and grain boundary oxidation were observed. At 800 C, oxidized grain boundaries were cracked by intersecting slip bands which resulted in intergranular failure. The fine specimens had crack initiation later in the fatigue life, but with more rapid propagation crack propagation.

Lerch, B. A.↗
NASA NTRS2021

Analysis of Nonlinear Shrinkage for the Bound Metal Deposition Manufacturing using Multi-scale Approach

We consider problem of nonlinear shrinkage of the metal part during bound metal deposition manufacturing on the ground and in zero-G. To analyze this problem we developed multi-scale physics-based approach that spans atomistic dynamics at the scale of nanoseconds and the full part shrinkage at the time scale of hours. Using this approach we estimated the key parameters of the problem including grain boundary width, coefficient of surface diffusion, initial redistribution of particles during debinding stage, micro-structure evolution from round particles to densely packed grains and corresponding change of the total and chemical free energy, and sintering stress. The introduced method was used to predict shrinkage at the level of two particles, filament cross-section, sub-model, and the whole green, brown, and metal parts. To further improve accuracy and reliability of the shrinkage predictions we propose concept of intelligent additive manufacturing of metal powders in space that combines the strengths of both physics-based and data-driven methods of analysis of AM.

bound metal deposition↗
NASA NTRS1972

Effect of metallurgical structure and properties on adhesion and friction behavior of cobalt alloys

The metallurgical structure and some of the mechanical properties of two cobalt alloys, cobalt-50% iron and cobalt-25% molybdenum-10% chromium, were determined under various heat treated conditions. The mechanical properties of the bcc disordered Co-50Fe alloy, which was found to be very brittle, indicated an exceedingly low fracture strength, low hardness, and very weak grain boundary strength. Ordering by suitable heat treatment only produced a more brittle material with a lower fracture strength and a slightly higher hardness value. Work hardening was found to produce a finer grain structure and a greater grain boundary strength. Tensile properties were examined. It was found that the Co-25Mo-10Cr alloy was difficult to place in the alpha Co solid solution condition, which limited the ability to use precipitation as a hardening reaction. Over two hundred adhesion cycles from zero contact load, to maximum load, to fracture were conducted between couples for each of the above alloys in an ultrahigh vacuum system which would permit the sample surfaces to be cleaned of all contaminant layers. In the Co-50Fe case, the calculated fracture stress from the adhesion tests showed values in the range of 80 to 150 k.s.i., which is about ten times greater than the values from tension tests.

Keller, D. V., Jr.↗
DOE OSTI2024

The Defects Genome of Janus Transition Metal Dichalcogenides

2D Janus Transition Metal Dichalcogenides (TMDs) have attracted much interest due to their exciting quantum properties arising from their unique two-faced structure, broken-mirror symmetry, and consequent colossal polarization field within the monolayer. While efforts are made to achieve high-quality Janus monolayers, the existing methods rely on highly energetic processes that introduce unwanted grain-boundary and point defects with still unexplored effects on the material's structural and excitonic properties Through high-resolution scanning transmission electron microscopy (HRSTEM), density functional theory (DFT), and optical spectroscopy measurements; this work introduces the most encountered and energetically stable point defects. It establishes their impact on the material's optical properties. HRSTEM studies show that the most energetically stable point defects are single (V S and V Se ) and double chalcogen vacancy (V S −V Se ), interstitial defects (Mi), and metal impurities (MW) and establish their structural characteristics. DFT further establishes their formation energies and related localized bands within the forbidden band. Cryogenic excitonic studies on h-BN-encapsulated Janus monolayers offer a clear correlation between these structural defects and observed emission features, which closely align with the results of the theory. Finally, the overall results introduce the defect genome of Janus TMDs as an essential guideline for assessing their structural quality and device properties.

2D materials↗
DOE OSTI2023

Using 3D position sensitivity to reveal response non-uniformities in CdZnTe, TlBr, and CsPbBr 3 detectors

Position sensitivity enables the correction of response non-uniformities in room-temperature semiconductor detectors caused by crystal defects and other factors. It can also be used to pinpoint the exact location of crystal defects responsible for the response variations. This work describes a technique for revealing and visualizing the detector regions affecting the charge collection efficiency in CdZnTe (CZT), TlBr, and CsPbBr 3 detectors configured as position-sensitive virtual Frisch-grid (VFG) devices. The technique correlates the photopeak events in energy spectra with their spatial distributions inside the detectors using the position information. By selecting the events from narrow energy intervals within a photopeak, we can visualize the detector volumes with particular charge collection efficiencies, which, in turn, correlate with the locations of electrode and crystal defects. Here, we demonstrate this technique in several examples. Columnar structures in the volume plots (position distribution maps) are consistent with signal losses near or at the anode in selected samples of CZT and TlBr. Structures exhibiting a distinct depth dependence are consistent with grain boundaries or other crystal defects.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2022

Three-dimensional imaging of grain boundaries via quantitative fluorescence X-ray tomography analysis

Abstract Three-dimensional visualization of material composition within multiple grains and across complex networks of grain boundaries at nanoscales can provide new insight into the structure evolution and emerging functional properties of the material for diverse applications. Here, using nanoscale scanning X-ray fluorescence tomography, coupled with an advanced self-absorption correction algorithm developed in this work, we analyze the three-dimensional gain distributions and compositions in a Ce 0.8 Gd 0.2 O 2-δ -CoFe 2 O 4 mixed ionic-electronic conductor system with high accuracy and statistical significance. Our systematic investigation reveals an additional emergent phase and uncovers highly intriguing composition stability ranges for the multiple material phases within this system. The presented visualization of composition variations across complex interfaces, supported by our quantitative composition analysis, discloses mechanistic pathways of the diverse phase transformations occurring in the material synthesis, providing insights for the optimization of transport properties in the mixed ionic-electronic conductor system.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Texturing of high T(sub c) superconducting polycrystalline fibers/wires by laser-driven directional solidification in an thermal gradient

This paper summarizes the technique of laser-driven directional solidification in a controlled thermal gradient of yttria stabilized zirconia core coated Y-Ba-Cu-O materials to produce textured high T(sub c) superconducting polycrystalline fibers/wires with improved critical current densities in the extended range of magnetic fields at temperatures greater than 77 K. The approach involves laser heating to minimize phase segregation by heating very rapidly through the two-phase incongruent melt region to the single phase melt region and directionally solidifying in a controlled thermal gradient to achieve highly textured grains in the fiber axis direction. The technique offers a higher grain growth rate and a lower thermal budget compared with a conventional thermal gradient and is amenable as a continuous process for improving the J(sub c) of high T(sub c) superconducting polycrystalline fibers/wires. The technique has the advantage of suppressing weak-link behavior by orientation of crystals, formation of dense structures with enhanced connectivity, formation of fewer and cleaner grain boundaries, and minimization of phase segregation in the incongruent melt region.

Varshney, Usha↗
DOE OSTI2025

An energetic link between order and strength in metals: A nanocrystalline strength limit in high-entropy alloys and intermetallic compounds

The metallurgy and materials communities have long understood and exploited fundamental links between chemical and structural ordering in metallic solids to tailor their mechanical properties. We extend these ideas to include prediction of the nanocrystalline strength limit in high-entropy alloys and intermetallic compounds, where a breakdown occurs in the classical Hall-Petch strengthening behavior. The highest reported strength achievable through alloying has rapidly climbed and given rise to new classifications of materials with extraordinary properties, with a notable case being nanocrystalline metals. High-entropy alloys (chemically disordered, concentrated solid solutions) and intermetallic compounds are two boundary cases of how tailored order can be used to manipulate mechanical behavior. Here, we show that the complex electronic-structure mechanisms governing the peak strength of alloys and pure metals can be reduced to a few physically meaningful parameters based on their atomic arrangements and used – with no fitting parameters – to predict the maximum strength of these materials. This includes a generalized energy-based accounting for the degree of structural and chemical ordering that allows for rapid and reasonably accurate prediction of peak strength (validated in the nanocrystalline limit) as a function of temperature. Predictions of maximum strength based on the activation energy (with all materials properties derived from DFT calculations or experiments) for a stress-driven transition to an amorphous state is shown to accurately describe the breakdown in Hall-Petch behavior at the smallest crystallite sizes for pure metals, intermetallic compounds, high-entropy alloys, and metallic glasses. Further, this activation energy is also shown to be directly proportional to interstitial electronic charge density, which is a good predictor of ductility, stiffness (moduli), and phase stability in high-entropy alloys and solid metals generally. The proposed framework suggests the possibility of coupling ordering and intrinsic strength to mechanisms like dislocation nucleation, hydrogen embrittlement, and transport properties, such as through correlations between the activation energies for amorphization with stacking-fault and grain boundary energies. It additionally opens the prospect for greatly accelerated structural materials design and development to address materials challenges limiting more sustainable and efficient use of energy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Molecular-Resolution Electron Imaging of Defects and Dynamics at the Ice-Water Interface

Water crystallization into hexagonal ice (type I h ) is one of the most critical processes relevant to the Earth’s environment and human activities. However, despite recent breakthroughs in imaging non-equilibrium condensed ice structures, the ice-water interface has never been imaged at a molecular resolution. This is primarily due to the low stability of the hydrogen bonds in ice under high-resolution microscopy conditions and a lack of methods to prepare compatible samples. Here, this presentation describes the first molecular-resolution imaging of ice crystallized from liquid water and the ice-water interface using high-resolution transmission electron microscopy (HRTEM). By encapsulating deionized (DI) water between two amorphous carbon (a-C) TEM grids and subsequently freezing it with liquid N 2 on a cryo sample stage, we generated two types of ice: non-equilibrium, condensed ice from the atmosphere and encapsulated ice from the DI water (Fig. 1A). Condensed ice usually shows irregular, spherulitic shapes (Fig. 1B). Selected area electron diffraction (SAED) shows that they are a mixture of cubic and hexagonal crystals (Fig. 1C). On the contrary, encapsulated ice forms thin films that contain large-area single-crystalline regions of hexagonal ice oriented along the [0001] zone axis (Fig. 1D). Differential electron energy-loss spectroscopy (EELS) confirmed the high purity of the encapsulated ice free from organic contaminations that are common in other encapsulation methods for HRTEM such as graphene liquid cells. These single-crystalline areas are robust under the electron beam up to ~100 e/Å 2 s. Aberration-corrected HRTEM imaging in these areas achieved a line resolution of ~1.3 Å (Fig. 1E and F). This platform allows us to study near-equilibrium ice structures and dynamics at an unprecedented spatial resolution (Fig. 2). For example, we discovered subdomain-rich regions near the defective crystal edges despite the structure appearing single-crystalline according to diffraction criteria. These subdomains connect via low-angle grain boundaries with flat energy landscapes as a function of tilt angles (according to simulations), showing the high tolerance of ice to defect structures. When we tuned the sample temperature and electron flux rate, we observed radiolysis-controlled bubble generation and dissolution in ice single crystals near a steady state of bubble dynamics. Furthermore, rich beam-induced melting and recrystallization dynamics were observed at the ice-water interface with lattice resolution. These data represent the first observation of the ice-water phase transformation at the sub-nanometer level. In summary, the methods developed in this work enabled molecular-resolution observations of ice and the ice-water interface and shed light on the microstructures and phase transformation pathways. Finer control on the temperature, electron irradiation profile, and imaging detector could eventually lead to real-time observation of ice nucleation in water and address long-standing questions in the nucleation pathways.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

Segregation of Al and its effect on coercivity in Nd-Fe-B

Doping a small amount of Al can effectively enhance coercivity in Nd-Fe-B magnets. Here we investigated the partitioning behavior of Al and its effect on coercivity in Nd-Fe-B using first principles DFT (density functional theory) calculation and micromagnetic simulation. The calculated substitution energies of Fe by Al are negative at the crystallographic sites of 4c and 8j 2 while they are positive values at the other sites in Nd 2 Fe 14 B (2:14:1), implying a small solubility of Al in 2:14:1. Further, Al prefers to segregate at grain boundary (GB) and stabilize the Nd-Fe-Al phase with a Nd 6 Fe 13 Si-type tetragonal structure (6:13:1). The formation of the antiferromagnetic or weak ferrimagnetic 6:13:1-like phase depletes Fe and reduces the amount of ferromagnetic Nd–Fe type grain boundary phase (GBP), which weakens the inter-grain magnetic interaction. Micromagnetic simulations indicate that the 6:13:1-like GBP increases the pinning field of magnetic domain wall at GB and suppresses the nucleation of reversal magnetic domain on the grain surface of 2:14:1 during demagnetization process. The formation of Al-rich shell on 2:14:1 grain surface can further moderately increase the domain pinning field at GB and the nucleation field of 2:14:1 grain. Developing novel processing method to tailor Al segregation and promote formation of 6:13:1-like phase at GB can be a promising approach to improve coercivity in Nd-Fe-B magnet.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Investigation of Microstructures and Tensile Properties of 316L Stainless Steel Fabricated via Laser Powder Bed Fusion

In this study, a thorough investigation of the microstructures and tensile properties of 316L stainless steel fabricated via laser powder bed fusion (L-PBF) was done. 316L stainless steel specimens with two different thicknesses of 1.5 mm and 4.0 mm fabricated under similar conditions were utilized. Microstructural characterization was performed using optical microscopy (OM) and scanning electron microscopy (SEM) equipped with electron backscatter diffraction (EBSD). Melt pools and cellular structures were observed using OM, whereas EBSD was utilized to obtain the grain size, grain boundary characteristics, and crystallographic texture. The 1.5 mm thick sample demonstrated a yield strength (YS) of 538.42 MPa, ultimate tensile strength (UTS) of 606.47 MPa, and elongation to failure of 69.88%, whereas the 4.0 mm thick sample had a YS of 551.21 MPa, UTS of 619.58 MPa, and elongation to failure of 73.66%. These results demonstrated a slight decrease in mechanical properties with decreasing thickness, with a 2.4% reduction in YS, 2.1% reduction in UTS, and 5.8% reduction in elongation to failure. In addition to other microstructural features, the cellular structures were observed to be the major contributors to the high mechanical properties. Using the inverse pole figure (IPF) maps, both thicknesses depicted a crystallographic texture of {001} <101> in their as-built state. However, when subjected to tensile loads, texture transitions to {111} <001> and {111} <011> were observed for the 1.5 mm and 4.0 mm samples, respectively. Additionally, EBSD analysis revealed the pre-existence of high-density dislocation networks and a high fraction of low-angle grain boundaries. Interestingly, twinning was observed, suggesting that the plastic deformation occurred through dislocation gliding and deformation twinning.

316L stainless steel↗
DOE OSTI2024

Grain boundary self-diffusion and point defect interactions in α -U via molecular dynamics

Though metallic U-Zr fuel has been used in nuclear reactors since the 1960s, many of its fundamental and thermodynamic properties are still unknown. The a-U phase, which has a highly anisotropic crystal structure and physical properties, is present in U-Zr fuel. The character and behavior of a-U grain boundaries will strongly impact fuel thermophysical performance under irradiation. Here, we study the interaction of point defects with grain boundaries, diffusion along grain boundaries, and the predicted diffusional creep behavior of a-U via molecular dynamics. We calculate the segregation energy of vacancies and interstitials to grain boundaries and quantify the biased sink strength of the grain boundaries, and observe that this sink strength is not strongly dependent on the grain boundary orientation. We also find that grain boundary diffusivity is strongly dependent on the grain boundary energy and grain boundary orientation. The presence of point defects within the grain boundary can induce diffusion in grain boundaries with low formation energies and can enhance diffusion in high-energy grain boundaries. We also find that diffusional creep of a-U at prototypical metallic fuel operation conditions is extremely high and could help explain observed metallic fuel swelling behaviors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Fundamental Study of Fatigue Crack Initiation at Grain and Twin Boundaries in Austentic Stainless Steel (Final Technical Report)

The overarching goal of this project was to understand the dislocation-based mechanisms driving fatigue crack initiation at grain and twin boundaries. The hypothesis of the work is that dislocation structures equivalent to persistent slip bands (PSBs) form in the boundaries, leading to local stress concentrations and fatigue crack initiation. The sub-goals associated with this work include: • Understanding the evolution of the dynamic stress state and dislocation density surrounding PSB/grain boundary interactions. This will require the development of new techniques that couple high resolution electron backscatter diffraction (HREBSD) with in situ scanning electron microscopy (SEM) deformation. • Uncover the mechanisms by which dislocations are accommodated in grain and twin boundaries during fatigue. The proposed approach here is to conduct in situ transmission electron microscopy (TEM) deformation experiments on fatigued samples. • Establish correlations between microstructure, deformation accommodation, and crack initiation across time and length scales. This work primarily focuses on understanding fatigue crack initiation in austenitic stainless steels, though promising work by an undergraduate researcher extended the work to high purity Al.

42 ENGINEERING↗
DOE OSTI2025

Pressure-induced cation and vacancy disorder-order transition and near-zero τ f in deficient hexagonal perovskite Ba 8 ZnTa 6 O 24 dielectrics

Pressure applications can enable the tuning of atomic/defect ordering and provide access to new functional materials. Here, in this study, we report that pressure-induced structural transformation featuring disorder-order transition of both cations and vacancies in the 8-layer deficient hexagonal perovskite tantalate dielectrics Ba 8 ZnTa 6 O 24 , which transformed the structure from twin to shift and remarkably lowered the temperature coefficient of resonant frequency τ f down to near zero (∼0.56 ppm/°C) from 38 ppm/°C for the twinned precursor. The atomic scale STEM-HAADF and EDS results confirm the ordering of Zn in the Ta host at the nanometer scale in the shifted material featuring well-ordered Ba 8 ZnTa 6 O 24 slabs intergrown with Ba 3 ZnTa 2 O 9 and Ba 5 Ta 4 O 15 monolayers and anti-phase grain boundaries as planar defects. The pressure-induced twin-shift structural transformation of Ba 8 ZnTa 6 O 24 features the rare constant concentration of the hexagonal stacked layers, which is allowed by the vacancy ordering at the central layers of face-shared octahedral (FSO) trimers avoiding the FSO B-B repulsion, and remarkably the faster cationic ordering kinetics compared with the 2:1 ordered complex perovskites. Although the inclusion of numerous planar defects and the oxidizable atomic defects led to significant p-type conduction and inhomogeneous electrical microstructures, resulting in an extraordinarily high extrinsic dielectric loss for the high-pressure shifted Ba 8 ZnTa 6 O 24 pellet, the intrinsically near-zero τ f could make the shifted Ba 8 ZnTa 6 O 24 perovskite an ideal microwave dielectric resonator candidate if the defects could be eliminated.

high pressure↗
DOE OSTI2024

Computational modeling of coupled mechanical damage and electrochemistry in ternary oxide composite electrodes

Performance degradation of ternary layered oxide cathodes largely originates from their loss of structural integrity in cyclic usage. Mechanical damage, such as intergranular fracture of the active particles, is not only a mechanical cleavage process but also interferes with electrochemical kinetics such as infiltration of liquid electrolyte, surface corrosion of the constituent primary particles, and may eventually isolate the primary grains from the electron conducting network. Here, in this work, we develop a computational framework that integrates electrochemistry of a LiNi x Mn y Co 1−x−y O 2 (NMC) composite cathode with mechanical damage of the active particles. To fully examine the intricate chemomechanical behavior of the electrode, we evaluate the effects of the anisotropic material properties, the influence of mechanical potential on Li transport, and the concurrent intergranular fracture and electrolyte penetration along the grain boundaries upon multiple cycles. Electrolyte infiltration benefits capacity retention but aggravates further mechanical damage by corrosion. Structural failure mostly occurs in the first charging due to the anisotropic mechanical strain between the primary grains, while the resulting damage remains stable in the later few cycles. The results are consistent with experimental observations and the integration of electrochemistry and mechanical failure enables a step further understanding of the complex mechanism of battery degradation.

Battery degradation↗
NASA NTRSDate not supplied

Three-Dimensional In Situ Observations of Polycrystalline Microstructure Evolution During Directional Solidification of Transparent Alloys Aboard the ISS and Quantitative Comparison with Numerical Modeling

Cellular/dendritic microstructures formed during solidification have a crucial influence on the mechanical properties of a wide range of structural alloys. By minimizing the amount of gravity-induced convection in the liquid, directional solidification experiments using transparent organic alloys conducted in the DECLIC-DSI onboard the International Space Station have provided unique 3D in situ observations of the spatiotemporal evolution of the solid-liquid interface during the formation of cellular and dendritic microstructures under purely diffusive growth conditions. Those observations have made it possible to perform benchmark quantitative comparisons with the predictions of state-of-the-art phase-field simulations of microstructure formation in 3D on experimentally relevant length and time scales. This talk will report quantitative comparisons between microgravity experiments and phase-field simulations in succinonitrile-camphor alloys of two different compositions, which shed new light on the selection of dendritic array structures, and on roles of macroscopic curvatures and subgrain boundaries between grains with a small misorientation with respect to the temperature gradient in the spatiotemporal evolution of the primary cellular spacing.

Kaihua Ji↗
DOE OSTI2025

Developing reliable machine learning interatomic potential for Fe–Cr–Ni austenitic alloys

Gaining atomistic understanding of mechanical behavior of heat-resistant structural materials such as Fe–Cr–Ni-based alloys requires an approach with an accuracy close to density functional theory (DFT) that considers the intrinsic properties of the bulk lattice and important defects such as stacking faults, grain boundaries, and surfaces. This work aims to develop reliable machine learning interatomic potential (MLIAP) at cross-scale for Fe–Cr–Ni ternary alloys with a focus on the face-centered-cubic (fcc) solid solution structure. Leveraging the advantages of moment tensor potentials, which typically necessitate a relatively small training dataset and enable rapid calculations using the large-scale atomic/molecular massively parallel simulator package, we ensure the stability and accuracy of the trained potentials. Important defects such as stacking faults, grain boundaries, and surfaces for wide-range compositions are investigated. Structural, thermal, elastic, and defect properties are determined from molecular dynamics simulations comprising several thousand atoms, generated via canonical Monte Carlo simulations guided by the trained potential. The trained potential allows efficient atomic simulations of structural, thermal, and mechanical properties of fcc Fe–Cr–Ni solid solution alloys as a function of composition and temperature. Therefore, the MLIAP approach represents a major advancement from DFT calculations that are limited to small simulation sizes and traditional molecular dynamics simulations using relatively low accuracy potentials. Furthermore, this work outlines a practical foundation for further investigating the structural evolution and mechanical behavior of austenitic stainless steel and nickel-based alloys in a wide array of applications in extreme environments.

Crystal structure↗