Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gas sampling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

INFLUENCE OF SUPPLEMENTARY ARGON GAS SHIELDING ON THE MICROSTRUCTURE AND MECHANICAL BEHAVIOR OF SS316L ADDITIVELY MANUFACTURED BY DIRECTED ENERGY DEPOSITION

The dissolution of atmospheric gases into parts additively manufactured by directed energy deposition (DED) has long been of concern, and stock shielding solutions have usually proven inadequate at fully removing atmospheric gases from weld beads. The objective of this work was to design a new supplementary argon gas shroud for a specific DED printer and evaluate its effect on microstructure and macroscopic properties of SS316L and the potential for printing more reactive metals such as Ti-6Al-4V. This was investigated by printing four SS316L sample blocks, two with and two without the shroud, each printed in two different orientations. These samples were subsequently evaluated with inert gas fusion (IGF), SEM/EDS imaging, and tensile tests. The shroud reduced oxygen content by 0.019-0.031%, and SEM imaging revealed fewer oxide inclusions. A more dramatic reduction of 0.13% oxygen and 0.171% nitrogen was observed by the inert gas fusion of Ti-6Al-4V samples. Overall, the results indicated the shroud was successful at reducing atmospheric gas uptake within the print region and may enable the printing of reactive metal powders in DED systems.

Helvie, Kyle↗
DOE OSTI2023

Impact of Boron-Containing Lubricant Additive on Three-Way Catalyst Reactivity and Physicochemical Properties

Boron-containing compounds are one of the lubricant additive options due to their suitable properties for additives and have been used as commercial lubricant additives. In the present study, the impact of a boron-containing lubricant oil additive, AR9100 (BR), on Pd/Rh-based three-way catalyst (TWC) performance is investigated, and the results are compared with the baseline no-additive (NA) case and the industry standard zinc dialkyl-dithiophosphate (ZDDP) results. Accelerated engine aging is performed using a genset to expose the catalysts to lubricant additives at high temperatures. All aged TWC samples are investigated for reactivity in a bench-flow reactor and characterized using a variety of analytical techniques. Compared with the no-additive case, the temperatures of 90% conversion (T 90 ) of NO, CO, C 3 H 6 , and C 3 H 8 for the ZDDP-aged TWC sample increased by 34, 30, 37, and 48 °C. However, the T 90 of all gas species for the BR-aged TWC sample are similar to the NA-aged TWC sample. Additionally, a significant decrease in water–gas shift reactivity and oxygen storage capacity is observed in the ZDDP-aged sample, but not in the BR-aged sample. Inductively coupled plasma-optical emission spectrometry (ICP-OES) analysis and electron probe microanalysis (EPMA) maps of accelerated engine aging samples show the presence of phosphorus and boron in ZDDP- and BR-aged TWC samples, respectively. However, no boron-related peaks are observed in the X-ray diffraction (XRD) pattern of the BR-aged TWC sample, which may exist in the form of an amorphous phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Improvement of Drop‐Hammer Impact Testing for Safety Assessment of High Explosives Using 10‐mg Samples

Here, in this study, we established an improved method for drop-hammer impact testing of small quantities of high explosives (10 mg). We performed about seven hundred impact tests under various experimental conditions (e.g., sandpaper vs bare anvil, different sample masses, drop-weights, and striker diameters) to determine an optimal set of conditions and reaction detection methods (e.g., gas analysis, video, and sound recordings) that give the most statistically reliable results with 10 mg samples. We used both Frequentist and Bayesian statistical approaches to compare estimates of the drop height (DH50) that initiates a reaction 50% of the time, and to quantify the associated uncertainty. Gas analysis proved to be the most reliable reaction detection method, showing unambiguous rises in HE decomposition products (e.g., CO 2 ) even when the other indicators (e.g., sound, video) were inconclusive. The impact tests performed with a bare anvil showed much better reproducibility than those conducted with sandpaper, reducing the largest uncertainty observed in the data sets by a factor of 1.7. The DH 50 values obtained from three different sample masses (10, 20, and 35 mg) fell within the uncertainties of the measurements. We demonstrated the improved procedure (i.e., 10-mg samples, gas analysis, bare anvil, and Bayesian approach) on a variety of PETN samples having different surface areas and thermal histories.

PETN↗
DOE OSTI2020

Multimodal Mass Spectrometry Imaging (MSI) of Archean and Jurassic Geologic Samples

Current geochemical analytical techniques such as gas chromatography-mass spectrometry (GC-MS and $G\acute{C}GC-MS$) can effectively determine the composition and structure of the organic biosignatures within a sample but cannot resolve the spatial distribution of organic biosignatures within rocks or sediments. The spatial distribution can be used to determine the character of the organic biosignatures [1], which can be indigenous (deposited with host rocks), non-indigenous (incorporated after deposition via fluid migration), or contaminant. Determining the character of organic biosignatures is critical for ancient samples [2] and will be critical if organics are observed in samples returned from Mars [3].Fs-LDPI-MS has the ability to map organic compounds across the surface of samples at 2 - 10 μm lateral resolution. Furthermore, fs-LDPI-MS can be used to carry out multiple analyses in the same location for micron-scale analysis of previously buried material [4]. We used fs-LDPI-MS to examine a ~164 million year old organic-rich mudstone from SW England (14.2 wt. % total organic carbon) [5] and determined the spatial distribution of likely indigenous components buried below potentially contaminated surface layers.We then used ToF-SIMS to re-analyze the mudstone to directly compare ToF-SIMS to fs-LDPI-MS datasets, and to analyze a series of ~2.7 billion year old geologic samples from Timmins, ON, CA [6]. Ref. [6] previously analyzed the Archean samples and observed a series of archaeal biomarkers, as well as hopanes and steranes. Using ToF-SIMS analysis, we were able to detect hopanes and steranes in the mudstone samples, but not in the Archean samples indicating that the hopanes and steranes are most likely contaminants in the Archean samples. We also did not observe the archaeal biomarkers; however, this may be from the lack of molecular ion preservation during ToF-SIMS.

Pasterski, Michael↗
DOE OSTI2020

A mass spectrometry-based high-throughput screening method for engineering fatty acid synthases with improved production of medium-chain fatty acids

Microbial cell factories have been extensively engineered to produce free fatty acids (FFAs), key components of crucial nutrients, soaps, industrial chemicals, and fuels. Yet, our ability to control the specificity of microbially synthesized FFAs is still limited for medium-chain fatty acids (MCFAs), which is mainly due to lack of high-throughput approaches for FFA analysis. Here we report a mass spectrometry (MS)-based method for rapid profiling of MCFAs in Saccharomyces cerevisiae by using membrane lipids as a proxy. Specially, matrix-assisted laser desorption/ionization time-of-flight (MALDI-ToF) MS was used to detect shorter acyl chain phosphatidylcholines from membrane lipids and the m/z peak ratio at 730 and 758 was used as an index for improved MCFA production. This yeast colony-based method can be performed at a rate of ~2 second per sample, which is much faster than the gold standard gas chromatography (GC)-MS (typically > 30 min per sample). To demonstrate the power of this method, we performed site-saturation mutagenesis of the yeast fatty acid synthase and identified 9 mutants that resulted in improved MCFA production relative to the wild-type strain. This colony-based MALDI-ToF MS screening method offers an alternative way for engineering microbial fatty acid compositions in a high-throughput manner.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Modeling gas migration through clay-based buffer material using coupled multiphase fluid flow and geomechanics with stress-dependent gas permeability

A model for gas migration through clay-based buffer material is developed for modeling gas generation and migration associated with deep geologic nuclear waste disposal. The model is based on a multiphase fluid flow and geomechanics simulator that is adapted to consider enhanced gas flow when gas pressure is high enough to approach the confining stress magnitude. A key feature in the model is a direct coupling between gas permeability and stress, through a non-linear stress-dependent permeability function. The model was first tested and calibrated by modelling two different laboratory gas migration tests on Wyoming (MX-80) bentonite samples. The calibrated model was then applied to model gas migration through a bentonite buffer of a large-scale gas injection test (Lasgit) conducted at the Äspö Hard Rock Laboratory in Sweden. Observed preferential gas migration along interfaces (between compacted blocks and along the canister surface) required explicit representation of such interfaces in the model. The model with the stress-dependent gas permeability accurately captured observed experimental responses in terms of gas breakthrough time, peak gas pressure, and cumulative gas flow rates. The calibrated model was finally applied to simulate migration of hydrogen gas generated within a breached nuclear waste canister over 10,000 years, involving migration of much larger gas volumes. For the considered gas generation rate and host rock properties, the generated gas could migrate through the bentonite buffer and released into the surrounding host rock at a maximum gas pressure somewhat higher than the initial total stress, though a significant amount of hydrogen remained within the buffer. This modelling sets the stage for further detailed analysis of the impact of hydrogen gas generation on the long-term performance of nuclear waste repositories.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Leaf C and N content, Feb2016-May2016, PA-SLZ, PA-PNM, PA-BCI: Panama

This dataset contains carbon, hydrogen and nitrogen content data of 33 tree species collected from February to May 2016 at the NGEE-Tropics Bosque Protector San Lorenzo (PA-SLZ) and Parque Natural Metropolitano (PA-PNM) sites in Panama. Data from Barro Colorado Island (PA-BCI) is only available for March 2016. This data was collected as part of the 2016 ENSO campaign. See related datasets for further sample details, leaf water potential, leaf spectra, gas exchange and leaf mass per area (LMA). Most leaves were sampled from sunlit canopy trees. VERSION 2 update. The identification of a species from the PNM site has been corrected as follows: the identification of the tree initially identified as Pseudosamanea guachapele (ALBIED) has been revised to Albizia adinocephala (ALBIAD). The updated data package includes revised data, metadata and protocol documents updated to reflect this change.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Removal of trace gases can both increase and decrease cloud droplet formation

Aerosols consist of liquid or solid particles dispersed in a gas. Aerosol measurements generally rely on drying the particles before quantifying their physicochemical properties. This drying can potentially remove semivolatile compounds from the particles. Here, we show size-resolved cloud condensation nuclei (CCN) measurements quantifying the hygroscopicity parameter in the presence and absence of a denuder. The denuder efficiently removed alkanes and weakly functionalized acids, aldehydes, and alcohols with fewer than 10 carbon atoms from the gas phase. Denuding organic compounds perturbed the CCN-derived hygroscopicity parameter by up to 50%. Denuding either rendered the particles more or less CCN active, and the direction of the effect depended on sample relative humidity and trace gas concentration. The effect was weakest in early spring and strongest in late spring and summer. The measurements demonstrate an unexpectedly strong coupling between the particle and gas phase, influencing CCN activity through either volatilization or surface adsorption, or both.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

High-temperature NMR MAS probe with optimized temperature gradient across sample rotor

A rotor housing assembly for NMR spectroscopy. An elongate rotor has a distal drive end, a proximal end and an internal sample space positioned along its length between the drive and proximal ends. The rotor is driveable about a rotation axis by a drive gas flow. A rotor housing has an interior space in which the rotor is at least partially received. At least one first heated gas flow inlet is positioned opposite the internal sample space, through which a first heated gas flow is controllably flowable into the interior space to heat it and the rotor. At least a pair of spaced apart second heated gas flow outlets are axially spaced from the first heated gas flow inlet to controllably convey a second heated gas flow to heat distal and proximal areas of the sample space to minimize a temperature gradient extending axially within the sample space.

Mehta, Hardeep S.↗
DOE OSTI2020

Water and Ammonia Desorption from 5A Zeolite

Demonstrate adsorption and desorption characteristics of water and ammonia on 5A zeolite during regeneration conditions using a Thermogravimetric analyzer (TGA) on samples previously evaluated by residual gas analyzer (RGA)/mass balance. Molecular sieve (zeolite) adsorbents have the following characteristics: Crystalline alumino-silicates containing pores or 'cages' that adsorb water or other molecules. Polar compound are adsorbed with high loading even at very low concentrations of the fluid. A 5A molecular sieve was chosen for its ability to adsorb both water and ammonia (NH{sub 3}) from a carrier gas stream. Preliminary RGA/mass balance testing indicated: 5A zeolite captured both NH{sub 3} and water as anticipated based on molecular size; Reloading showed limited success after zeolite heated beyond manufacturer recommended operating conditions: Steam dealumination theorized cause; Tests were reprioritized to focus on NH{sub 3} removal and end of life potential holdup of NH{sub 3} and water on 5A zeolite material. TGA measures a sample's weight and volatile composition as it is heated or cooled in a furnace. TGA heats sample to release volatile materials, (change in mass is measured). MS detects/measures low levels of impurities. Perform TGA desorption of zeolite samples taken at the following conditions tested with RGA (RGA results not shown here): Initial Bakeout conditions: hydrogen carrier gas, slowly raise temp to approximately 300 deg. C until desired moisture content <<100 ppm is achieved. Water loading (re-loading): argon carrier gas through bubbler until breach is observed. Ammonia loading (re-loading): hydrogen carrier gas through system. Regenerations/End of life conditions: hydrogen carrier gas, raise temp to approximately 300 deg. C, then slowly to 450 deg. C (end of life). After end of life testing less than 4% of the total mass was residual ammonia or water at bakeout conditions. Peak water and ammonia removal occurred around 275 deg. C and 150 deg. C respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Drying Wet Stored and Corroded Magnox Fuel for Interim Dry Storage - 20187

To investigate the feasibility of drying corroded Magnesium alloy clad nuclear fuel, the corrosion products of inactive and unirradiated Magnox simulant dry corrosion product and dried corroded Magnox sludge were characterised by X-ray diffraction and thermogravimetric analysis. XRD identified brucite in the dried corrosion product and both brucite and hydromagnesite in the sludge. TGA identified mass loss on dehydration of ∼9.1% up to 250 deg. C and 27.9% from dehydroxylation up to 440 deg. C, with total mass loss of 41.9% up to 800 deg. C for the dried corrosion product. The sludge TGA showed 8.3% mass loss up to 250 deg. C from dehydration, 7.5% up to 330 deg. C from dehydroxylation and 31.4% mass loss up to 47.2% for decarbonation, with total mass loss of 49.2% up to 800 deg. C. Water removal up to 1.8 g was performed by cold vacuum drying (40 deg. C-120 deg. C) on a ≅14.8 g (wet) corroded Magnox sample. The process was monitored by observing pressure, dew point, temperature and gas flow changes supported by measuring the sample mass loss as water is removed. From these tests, it was observed that the dried corroded Magnox displayed some hygroscopic capacity which has implications for water retention following vacuum drying and the length of exposure required to achieve the desired dryness. Whilst at higher temperatures the water was removed faster, the increased temperature also risks the fuel cladding undergoing unwanted chemical reactions with the residual water during the process. However, at lower temperatures the achievable levels of dryness were reduced. Therefore, from these observations this work has identified that there is a temperature balance that may be necessary to optimise the drying process with respect to allowing the greatest level of dryness whilst restricting unwanted chemical reactions. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Air separation via two-step solar thermochemical cycles based on SrFeO 3-δ and (Ba,La) 0.15 Sr 0.85 FeO 3-δ perovskite reduction/oxidation reactions to produce N 2 : rate limiting mechanism(s) determination

Two-step solar thermochemical cycles based on reversible reactions of SrFeO 3–δ and (Ba,La) 0.15 Sr 0.85 FeO 3–δ perovskites were considered for air separation. The cycle steps encompass (1) the thermal reduction of SrFeO 3–δ or (Ba,La) 0.15 Sr 0.85 FeO 3–δ perovskites driven by concentrated solar irradiation and (2) oxidation in air to remove O 2 and produce N 2 . Rate limiting mechanisms were examined for both reactions using a combination of isothermal and non-isothermal thermogravimetry for temperature-swings between 673 and 1373 K, heating rates of 10, 20, and 50 K min –1 , and O 2 pressure-swings between 20% O 2 /Ar and 100% Ar at atmospheric pressure. Evolved O 2 and associated lag due to transport behavior were measured with gas chromatography and used with measured sample temperatures to predict equilibrium compositions from a compound energy formalism thermodynamic model. Measured and predicted chemical equilibrium changes in deviation from stoichiometry were compared. Rapid chemical kinetics were observed as the samples equilibrated rapidly for all conditions, indicative that heat and mass transfer were the rate limiting mechanisms. Furthermore, the effects of bulk diffusion (or gas diffusion through the bed or pellet) were examined using pelletized and loose powdered samples and determined to have no discernable impact.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Neutron and photon in-vivo materials characterization at the evolving plasma-material interface in plasma-burning fusion environments

This report includes the first set of MOSS data collected in the context of fusion-relevant plasma-material interactions. The data collected show that the surface curvature and stress irreversibly change during low-energy deuterium ion irradiation. This holds for both tungsten thin films, bulk tungsten, and single-crystal silicon. Meanwhile, argon irradiation did not produce this same effect. The surface morphology of the exposed samples was virtually identical regardless of gas species. There were, however, some surface chemistry differences between argon-exposed and deuterium-exposed samples, mainly concerning the oxide states of the W4f XPS signal. The changes in surface chemistry could be due to hydrogen dynamics on the tungsten surfaces, though further investigation will be required with in-situ irradiation and analysis. The changes in surface stress could also not be explained by temperature alone, as the temperature reached during the ion irradiations was too low to induce non-elastic strain. With this in mind, deuterium retention in the materials could change the surface curvature and stress. To confirm this, further work will be needed to quantify the change in curvature and relate it to ion flux, fluence, and deuterium retention. Unfortunately, when this work was conducted, the experimental setup for thermal desorption spectroscopy was not operating correctly, and that work could not be included in this dissertation. Despite experimental difficulties, this work shows the first results of a promising technique to study deuterium dynamics in tungsten-based reconstituted thin films.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Probing the Impact of Radio-mode Feedback on the Properties of the Cool Circumgalactic Medium

We explore the influence of radio-mode feedback on the properties of the cool circumgalactic medium (CGM). To this end, we assemble a statistical sample of approximately 30,000 radio galaxies with background quasars by combining optical spectroscopic measurements of luminous red galaxies and quasars from the year 1 data set of the Dark Energy Spectroscopic Instrument and radio sources from the LOw-Frequency ARray Two-metre Sky Survey (LoTSS) DR2 catalog and the Very Large Array Sky Survey (VLASS) quick-look catalog. Galaxies with similar optical properties but with no radio counterparts in LoTSS and VLASS are selected as the control group. We measure the cool CGM properties of radio galaxies and their control samples traced by Mg ii absorption lines, including covering fraction, rest equivalent width, and gas kinematics. Our results show no significant difference in the properties of gas around radio galaxies and their control sample, indicating that the operating radio-mode feedback of massive galaxies does not produce detectable effects on the properties of the cool CGM. Finally, we show that the CGM of radio galaxies contains a nonnegligible amount of cool gas with approximately 10 10 M ⊙ . This abundance can place a stringent constraint on the radio-mode feedback models.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

Investigation of desorption of hydrogen gas from polymer matrix using thermal desorption analysis and finite element modeling

Polymer materials are used widely as sealing materials and liners in hydrogen storage and transportation infrastructure. During operating conditions, polymers are exposed to high pressure hydrogen gas periodically. When in contact, the hydrogen gas diffuses through the polymer material with ease due to its smaller sized molecules compared to the polymer molecules. In the event of rapid decompression of outside hydrogen gas, the hydrogen molecules within the polymer diffuse out. This process is known as the desorption of polymer and can cause blisters or cracking causing permanent damage to the polymer. Here, we used a combined experimental and modeling approach to investigate the desorption of the hydrogen gas in the polymer. Thermal desorption analysis (TDA) experiments were performed on the polymer sample exposed to the high-pressure hydrogen gas to measure the diffusion coefficient and equilibrium hydrogen concentration. Experiments also provided the quantity of hydrogen within the polymer during the desorption process which followed Fick’s law. However, for higher pressurization values, some anomaly was observed in the quantity of hydrogen remaining in the polymer sample. A continuum mechanics based coupled diffusion–deformation-damage model was deployed to simulate the gas desorption process in the material using the finite element method to understand its effect on the material. It was found that the anomaly in TDA results were due to the blister formation on the polymer surface which resulted in longer hydrogen retention. Simulations also showed that blister formation can be affected by multiple parameters such as the addition of filler particles, and pre-existing cavity size.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An Assessment of the Conversion of Biomass and Industrial Waste Products to Activated Carbon

The production of biochar from biomass and industrial wastes provides both environmental and economic sustainability. An effective way to ensure the sustainability of biochar is to produce high value-added activated carbon. The desirable characteristic of activated carbon is its high surface area for efficient adsorption of contaminants. Feedstocks can include a number of locally available materials with little or negative value, such as orchard slash and crop residue. In this context, it is necessary to determine and know the conversion effects of the feedstocks to be used in the production of activated carbon. In the study conducted for this purpose; several samples (piñon wood, pecan wood, hardwood, dried grass, Wyoming coal dust, Illinois coal dust, Missouri coal dust, and tire residue) of biomass and industrial waste products were investigated for their conversion into activated carbon. Small samples (approximately 0.02 g) of the feedstocks were pyrolyzed under inert or mildly oxidizing conditions in a thermal analyzer to determine their mass loss as a function of temperature and atmosphere. Once suitable conditions were established, larger quantities (up to 0.6 g) were pyrolyzed in a tube furnace and harvested for characterization of their surface area and porosity via gas sorption analysis. Among the samples used, piñon wood gave the best results, and pyrolysis temperatures between 600 and 650 °C gave the highest yield. Slow pyrolysis or hydrothermal carbonization have come to the fore as recommended production methods for the conversion of biochar, which can be produced from biomass and industrial wastes, into activated carbon.

09 BIOMASS FUELS↗
DOE OSTI2022

Composition, Emissions, and Air Quality Impacts of Hazardous Air Pollutants in Unburned Natural Gas from Residential Stoves in California

The presence of hazardous air pollutants (HAPs) entrained in end-use natural gas (NG) is an understudied source of human health risks. We performed trace gas analyses on 185 unburned NG samples collected from 159 unique residential NG stoves across seven geographic regions in California. Our analyses commonly detected 12 HAPs with significant variability across region and gas utility. Mean regional benzene, toluene, ethylbenzene, and total xylenes (BTEX) concentrations in end-use NG ranged from 1.6–25 ppmv–benzene alone was detected in 99% of samples, and mean concentrations ranged from 0.7–12 ppmv (max: 66 ppmv). By applying previously reported NG and methane emission rates throughout California’s transmission, storage, and distribution systems, we estimated statewide benzene emissions of 4,200 (95% CI: 1,800–9,700) kg yr –1 that are currently not included in any statewide inventories–equal to the annual benzene emissions from nearly 60,000 light-duty gasoline vehicles. Additionally, we found that NG leakage from stoves and ovens while not in use can result in indoor benzene concentrations that can exceed the California Office of Environmental Health Hazard Assessment 8-h Reference Exposure Level of 0.94 ppbv–benzene concentrations comparable to environmental tobacco smoke. This study supports the need to further improve our understanding of leaked downstream NG as a source of health risk.

42 ENGINEERING↗
DOE OSTI2021

Hydrogen permeability and stability of palladium films in a high pressure reactor

Palladium (Pd) thin films were fabricated by colloidal spray deposition (CSD) on substrates of porous yttrium stabilized zirconium oxide (YSZ). The films were sintered at 1140–1160 °C for 2–3 h in argon and had thickness of 5–11 μm. The hydrogen (H 2 ) permeation flux for the Pd film was measured with simulated feed gases (90% H 2 /He, syn-gas/steam, or syn-gas/steam with H 2 S) flowing on the film side and sweep gas (Ar) flowing on the substrate side. Here, the hydrogen flux with the Pd film was obtained by adjusting the flow rate and pressure of the gas. Hydrogen flux values of 121–173 cm 3 min -1 cm -2 were measured at 388–596 °C (feed: 90% H 2 /He at 200 mL min -1 ; sweep: Ar at 1400 mL min -1 ; and ΔP = ~170 psi), and the permeability was calculated and compared with literature values. Because Pd is known to be sensitive to some gases, the stability of Pd films was evaluated by examining the microstructures of samples after their exposure to gas mixtures containing CO, CO 2 , H 2 O, and H 2 S. From the results of stability tests in H 2 S-containing atmospheres, the Pd/Pd 4 S phase boundary was determined, and this measured boundary was compared to the Pd/Pd 4 S boundary calculated from the thermodynamic data in the literature.

36 MATERIALS SCIENCE↗