Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FISSION GAS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

α-U and ω-UZr 2 in neutron irradiated U-10Zr annular metallic fuel

Here, to develop metallic fuel with ultra-high burnup of 30%-40%, an annular U-10Zr fuel with 55% smear density was fabricated through a casting route and irradiated at the Advanced Test Reactor at Idaho National Laboratory. The annular fuel design also serves as a demonstration of the feasibility to replace sodium bond with a helium bond to benefit the geological disposal of irradiated fuel, cut the cost of fuel fabrication, and boost the overall metallic fuel economy. This paper reports the results from transmission electron microscopy (TEM) based post-irradiation examination of this fuel type irradiated to a burnup of 3.3% fissions per initial heave metal atoms for initial screening purpose. After irradiation, the initial U-10Zr separated into an a-U annular region and an UZr 2+x center region with nanoscale spinodal decomposed microstructure. Because of the provided large amount of coherent interface areas, the fission gas atoms and vacancies generated in UZr 2+x phase are possibly pinned at the interface areas, leading to 20 times smaller fission gas bubbles than those in the neighboring a-U. The large bubbles in a-U become connected and merged into large pores that provide fast release paths for fission gas which prevents further fuel swelling. The fuel center still has open space to accommodate further fuel swelling from solid fission products at higher burnup. Other neutron irradiation induced phase and microstructure change are also characterized and compared with traditional solid fuel designs.

36 MATERIALS SCIENCE↗

MEXIICO: a new equipment to study the pressure impact on the irradiated fuel behavior

The new MEXIICO experimental loop has recently been started in the LECA-STAR hot-cell facility of the CEA Cadarache. It is dedicated to the understanding of the basic mechanisms occurring in nuclear fuels during nuclear reactor power transients and accidental situations. Under such conditions the nuclear fuels are submitted to thermo-mechanical stresses. These stresses play a major role on fission product release and fuel fragmentation. Evaluating such fuel behavior represents a key issue for reactor safety analyses. In the first part of the paper, we describe the complete MEXIICO device, which main component is a hot isostatic press allowing to perform analytical experiments in the [20 -1600 C. degrees / 10 MPa - 160 MPa] region. As shown by simulations (ALCYONE fuel performance code), the upper value of the pressure (160 MPa) is consistent with the one experienced by fuels under nuclear power transients. We also present the experimental loop starting from the argon pressurized feed-line, the furnace and its associated instrumentation and the exhaust line equipped with specific valves and flowmeters controlling the pressure and flowrate. We then focus on the gamma spectrometry measurement which allows recording the fission gas release kinetics. In the second part of the paper, we detail the capability of the MEXIICO device to provide new experimental data regarding the influence of pressure on the fission gas release and fuel fragmentation, and to determine a pressure threshold above which fission gas release and fuel fragmentation may be inhibited. This device also allows investigating the impact of pressure on the microstructure evolution, coupling it with post-test microanalysis examinations: this procedure will allow characterizing the effect of temperature and pressure on the bubble evolution and interconnection. Evolutions of the fuel modeling, needed to simulate correctly these new experimental data, will be also presented. In the last section of the paper, we present the commissioning tests of the MEXIICO device showing the good reproducibility of the tests performed first in conventional laboratory and then in hot-cell laboratory. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Transient fuel performance analysis for the preliminary fuel concept of general atomics fast modular reactor

This study investigates the transient fuel performance of General Atomics Fast Modular Reactor (GA-FMR) during accident scenarios, focusing on the behavior of its innovative fuel system that combines high-assay low enriched uranium dioxide (HALEUO2) fuel with SiGA® ceramic matrix composite silicon carbide cladding. The preliminary fuel design’s response was analyzed during reactivity-initiated accidents (RIA) and loss of coolant accidents (LOCA) using BISON fuel performance analysis code, which included both the diffusion enhanced and BISON-FASTGRASS coupled UO 2 models. The RIA analysis demonstrated that effective reactivity control reduced fuel temperature, though with transient fission gas release resulting in additional tensile stress state on the cladding. LOCA simulations revealed differing predictions between the two models: the BISON UO 2 model showed more transient fission gas release but minimal pellet expansion, while the BISON-FASTGRASS UO 2 model predicted less pronounced fission gas release but more fuel swelling and thermal expansion, potentially leading to pellet-cladding mechanical interaction. Here, these findings highlight critical areas for fuel design optimization and identify knowledge gaps requiring further experimental and computational investigation to advance GA-FMR fuel development.

Lee, Soon K. [Argonne National Laboratory (ANL), A↗

SEM Characterization of the High Burn-up Microstructure of U-7Mo Alloy

During irradiation, the microstructure of U-7Mo evolves until at a fission density near 5x1021 f/cm3 a high-burnup microstructure exists that is very different than what was observed at lower fission densities. This microstructure is dominated by randomly distributed, relatively large, homogeneous fission gas bubbles. The bubble superlattice has collapsed in many microstructural regions, and the fuel grain sizes, in many areas, become sub-micron in diameter with both amorphous fuel and crystalline fuel present. Solid fission product precipitates can be found inside the fission gas bubbles. To generate more information about the characteristics of the high-fission density microstructure, three samples irradiated in the RERTR-7 experiment have been characterized using a scanning electron microscope equipped with a focused ion beam. The FIB was used to generate samples for SEM imaging and to perform 3D reconstruction of the microstructure, which can be used to look for evidence of possible fission gas bubble interlinkage.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Segmentation and Classification of Fission as Pores in Reactor Irradiated Annular U–10Zr Metallic Fuel Using Machine Learning Models

Metallic fuels, particularly U—10Zr, are promising candidates for next-generation sodium-cooled fast reactors. Irradiation of nuclear fuels in reactors can lead to the formation of solid and gas fission product which subsequently forms microstructural pores, deteriorating fuel performance. Due to the massive amount of pores and complex phases formed, a quantitative description of fission gas pores is not yet available, preventing the development of microstructure-informed fuel performance modeling for fuel qualification. This paper applied a pre-trained deep learning model to ~10,260 high magnification scanning electron microscopy images. This method increased the accuracy of fission gas pore segmentation and allows statistical features to be extracted which cannot be achieved manually. A pre-trained decision tree model worked on the segemenation results and further classified the pores into different categories to produce a correlation between the pores, movement of lanthanides, and temperature gradient during irradiation. Finally, this paper emphasizes the potentials of machine learning models to accelerate fuel research, development, and qualification for advanced reactors.

36 MATERIALS SCIENCE↗

In-situ ion irradiation of a spent UO2 fuel: evolution of fission products and nanograins with radiation dose

This study investigates the behavior of fission gas bubbles, five metal precipitates (5MPs) (Mo, Ru, Rh, Tc, Pd) and nanograins in spent uranium dioxide (UO2) fuel under various ion irradiation doses, temperatures, and flux conditions. Utilizing in-situ ion irradiation and advanced transmission electron microscopy, we analyzed the evolution of fission gas bubbles, 5MPs and nanograins in UO2 samples from the Belgium Reactor 3 (BR-3). Our findings reveal significant shrinkage of fission gas bubbles and 5MPs with increasing irradiation dose, accompanied by a decrease in pair density. The study also reveals nanograin coarsening under irradiation. We demonstrate that ion irradiation induces a homogeneous re-solution process where individual atoms are ejected from bubbles and precipitates, leading to their dissolution and subsequent re-precipitation in the matrix. This study provides critical insights into the dynamic behavior of fission products and nanograins under irradiation, facilitating the development of predictive models and contributing to the optimization of nuclear fuel performance and safety.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

AGR-5/6/7 Release-to-Birth Ratio Data Analysis for Cycles 162B, 163A, 164A, and 164B

AGR-5/6/7 is the last of a series of Advanced Gas Reactor (AGR) experiments conducted in the Advanced Test Reactor (ATR) at Idaho National Laboratory in support of development and qualification of tristructural isotropic (TRISO) low-enriched fuel used in the high-temperature gas cooled reactor (HTGR). Each AGR test consists of multiple independently controlled and monitored capsules containing fuel compacts placed in a graphite cylinder shrouded by a steel shell. These capsules are instrumented with thermocouples (TC) that are embedded in the graphite, thus providing feedback for temperature control. AGR configuration and irradiation conditions are based on prismatic HTGR technology that is distinguished primarily through use of helium coolant, a low-power-density ceramic core capable of withstanding very high temperatures, and TRISO-coated particle fuel. The AGR tests provide valuable irradiation-performance data to support fuel process development, qualify fuel for normal operation and accident conditions, and support development and validation of fuel performance and fission-product transport models and codes. The release-to-birth ratios (R/B) for fission-gas isotopes (i.e., krypton and xenon) are calculated from release rates into the sweep-gas flow, measured by the high-purity germanium detectors used in the AGR Fission Product Monitoring System (FPMS) installed downstream from each irradiated capsule. Birth rates are calculated based on the fission power in the experiment and models of fission-product generation. Thus, the R/B is a measure of the ability of fuel kernel, particle coating layers, and compact matrix to retain fission-gas atoms, preventing their release into the sweep-gas flow, especially in the presence of initially defective particle and/or the event of particle-coating failures that occurred during the irradiation. For fission-gas isotopes, particle failure occurred when all coating layers are fractured that allow gaseous fission atoms to escape from a particle. In this case, the R/B per-exposed-kernel is used to compare fuel performance across experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Separate Effects Testing in TREAT for ATF Fuels

This work performed examinations on high burnup UO2 from commercial power plant with the intention of better understanding fission gas and fragmentation behavior. Fuel fragmentation, relocation, and dispersal (FFRD) is a major factor in fuel lifetime limits imposed on UO2 by regulators, both domestic and foreign, and is a major area of interest by industry groups (e.g., Electric Power Research Institute, [EPRI]). The characterization of the fuel focused on the differences in porosity between the high burnup (rim) zone, the dark (intermediate) zone, and center zones of the fuel as well as the fission gas content of each region. Work involved thermal treatments to analyze fission gas and high resolution microscopy techniques to investigate pore structure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation examinations of annular mixed oxide fuels with average burnup 4 and 5% FIMA

In this paper, we present post-irradiation examination results on two type of annular mixed oxide fuel pins irradiated in the Fast Flux Test Facility (FFTF) sodium cooled reactor to an average burnup between 4% and 5% fission of initial heavy atom (FIMA). The pins differed only from the initial Pu content, which was 22 wt% and 26 wt%, respectively. The overall performance of the pins was excellent, in line with previous historical results. The pins with higher Pu content experienced higher irradiation temperatures which influenced the fission gas release, fuel swelling, and Cs distribution compared to the other pins. All the post-irradiation examinations results are discussed against the irradiation parameters. In particular, the pins with higher initial Pu content, i.e., 26 wt%, experienced higher power that resulted in enhanced fission gas release compared to the other two pins with 22 wt% initial Pu content. For the pins with higher fission gas release, onset of Cs redistribution was observed. The two pins that had lower initial Pu content and burnup showed a Cs axial distribution similar to the as-produced one.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Random-Walk Monte Carlo Simulation of Intergranular Gas Bubble Nucleation in UO2 Fuel

Using a random-walk particle algorithm, we investigate the clustering of fission gas atoms on grain bound- aries in oxide fuels. The computational algorithm implemented in this work considers a planar surface representing a grain boundary on which particles appear at a rate dictated by the Booth flux, migrate two dimensionally according to their grain boundary diffusivity, and coalesce by random encounters. Specifically, the intergranular bubble nucleation density is the key variable we investigate using a parametric study in which the temperature, grain boundary gas diffusivity, and grain boundary segregation energy are varied. The results reveal that the grain boundary bubble nucleation density can vary widely due to these three parameters, which may be an important factor in the observed variability in intergranular bubble percolation among grain boundaries in oxide fuel during fission gas release.

36 MATERIALS SCIENCE↗

Results of the AGR-5/6/7 UCO TRISO fuel irradiation test in the Advanced Test Reactor

AGR-5/6/7 was the last in a series of irradiation experiments sponsored by the U.S. Department of Energy in support of the development and qualification of TRISO coated particle fuel for use in a high-temperature gas-cooled reactor. This experiment was conducted to verify the performance of the reference-design TRISO-coated low-enriched UCO fuel for modular high-temperature gas-cooled reactor normal operating conditions and to explore fuel performance at temperatures substantially beyond those typical of normal operation. A total of 194 UCO fuel compacts in five capsules were irradiated in the Advanced Test Reactor for 360.9 effective full-power days, achieving final burnup ranging from 5.66% to 15.26% fissions per initial heavy metal atom and fast neutron fluence ranging from 1.62 × 10 25 to 5.55 × 10 25 n/m 2 (E > 0.18 MeV). Calculated time-averaged fuel temperatures ranged from 467 °C to 1432 °C, with a peak fuel temperature of 1536 °C. During the first five irradiation cycles (∼180 effective full-power days), 85m Kr fission gas release-rate-to-birth-rate ratios were 10 −7 –10 −6 , indicating no particle failures. Near the end of the sixth cycle, a substantial number of in-pile particle failures occurred in Capsule 1. The fission gas release from this capsule impacted the readings from the other four capsules and led to unreliable fission gas release measurements for all capsules during the last four cycles. A preliminary post-irradiation examination of Capsule 1 fuel and internal components revealed the in-pile particle failures resulted from operational issues with the capsule, not subpar performance of the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effects of ZrN Coating and Heat Treatment on U-Mo Dispersion Fuel under Irradiation

The stability of U-Mo fuel particles in Al matrix can be improved using ZrN coating and heat treatment. This study investigated irradiation behaviors of fuel plates containing U-Mo fuel particles fabricated with different conditions including heat treatment and the thickness of ZrN coating. Additionally, different fission densities were applied to each fuel plate to understand how varying fission densities affect its irradiation behaviors. This study showed that more recrystallization of grains and development of high burnup structure (HBS) occurred in irradiated fuel particles with higher fission densities. Heat treatment reduced the accumulation of fission gas bubbles in the fuel particles by coarsening their grains. The fuel particles with a ZrN coating thickness of 1.2-1.8 µm showed less significant development of U-Mo/Al interaction layers than the particles with a coating thickness of 0.5 µm after irradiation. This might indicate the existence of a critical thickness of ZrN coating to minimize the formation of the interaction layers. Fission gas bubbles were observed at grain boundaries of irradiated U-Mo fuel particles at low fission densities, and the formation of dendritic features with a darker contrast was identified in backscattered electron images. These features stemmed from grain boundaries with fission gas bubbles or HBS, and some of them contained the bubbles, indicating that they might represent an early stage of HBS propagation in the fuel particles.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Blister Threshold Based Thermal Limits for the U-Mo Monolithic Fuel System

Fuel failure is most commonly induced in research and test reactor fuel elements by exposure to an under-cooled or over-power condition that results in the fuel temperature exceeding a critical threshold above which blisters form on the plate. These conditions can be triggered by normal operational transients (i.e. temperature overshoots that may occur during reactor startup or power shifts) or mild upset events (e.g., pump coastdown, small blockages, mis-loading of fuel elements into higher-than-planned power positions, etc.). The rise in temperature has a number of general impacts on the state of a fuel plate that include, for example, stress relaxation in the cladding (due to differential thermal expansion), softening of the cladding, increased mobility of fission gases, and increased fission-gas pressure in pores, all of which can encourage the formation of blisters on the fuel-plate surface. These blisters consist of raised regions on the surface of fuel plates that occur when the cladding plastically deforms in response to fission-gas pressure in large pores in the fuel meat and/or mechanical buckling of the cladding over damaged regions in the fuel meat. The blister temperature threshold decreases with irradiation because the mechanical properties of the fuel plate degrade while under irradiation (due to irradiation damage and fission-product accumulation) and because the fission-gas inventory progressively increases (and, thus, so does the gas pressure in pores).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mesoscale modeling to inform Bison models of accident tolerant fuel concepts

U 3 Si 2 and doped UO 2 have been under investigation in recent years as potential accident-tolerant fuel concepts. In this report, lower-length scale studies of these fuel concepts carried out during Fiscal Year 2020 are detailed. U 3 Si 2 is a potential accident-tolerant fuel that shows promise due to its high thermal conductivity and higher uranium density relative to UO 2 . However, its swelling and fission gas release behavior in light water reactor (LWR) conditions is relatively unknown. To provide mechanistic insight and determine parameters for engineering-scale fuel performance modeling of pellet-form U 3 Si 2 , phase-field simulations of the growth, interconnection, and venting of intergranular fission gas bubbles were performed. The fractional coverage of the grain boundary and the fraction of bubble area that is vented were calculated as a function of time. From the simulation data, the fractional grain boundary coverage at saturation, an important parameter needed in engineering-scale modeling of swelling and fission gas release, was determined. Multiple simulations were run to determine the uncertainty in the calculated value. The effect of model assumptions and input parameters that are not well known was evaluated. Simulation results are compared to related theoretical and computational work. Based on the simulation results, a value of 0.60 for the fractional grain boundary coverage at saturation is recommended for U 3 Si 2 fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mesoscale Modeling for Restructuring and Fragmentation in High Burnup UO 2

This report summarizes the mesoscale modeling conducted in fiscal year 2025 under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, focusing on the microstructural evolution and restructuring in high burnup UO 2 nuclear fuel and its impact on fuel fragmentation. We developed a pioneering phase-field model to simulate restructuring behavior across different regions of high burnup fuel, including the dark zone and rim region. A grand-potential-based phase-field model is employed to concurrently evaluate subgrain formation and the growth of fission gas bubbles within the fuel. An energy-based subgrain formation criterion was introduced to simulate the restructuring process. The effects of temperature and burnup rate were studied to capture how each of these parameters influences the characteristics of the restructured fuel. Subgrain formation was observed to initiate around existing fission gas bubbles and proceed toward triple junctions, grain boundaries, and grain interiors. Under a given subgrain formation rate, the rate of restructuring increases with rising fuel temperature. The restructuring occurs faster with higher burnup rate. A restructuring bias was observed within the microstructure, due to the variation in defect accumulation when comparing different grains. Microstructures corresponding to the dark zone and rim region can be obtained by parameterizing the model with the appropriate defect production rate, as determined based on the burnup rate and temperature. The predicted microstructures are consistent with experimental observations of the restructured regions. Based on the mesoscale simulations, a mechanistic model for restructuring and grain size evolution was implemented in BISON. Thus, this work provides a first-of-its-kind restructuring model for different regions of high-burnup fuel to BISON. It was shown that the model predicts appropriate grain size evolution along fuel radius as those observed in experiments. This model enables BISON to predict the effect of restructuring on the fission gas release. Finally, the phase-field fracture simulation with dark zone specific microstructures were presented to provide the fragmentation criteria for the dark zone. This work introduces a first-of-its-kind restructuring model for high burnup fuel, significantly enhancing BISON's predictive capabilities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Tailored Microstructure and Properties in UO{sub 2}

Advanced fuels with enhanced safety margin and accident tolerance are of vital importance for safe operation of current light water reactor fleet and the development of future reactor systems. The current UO{sub 2} fuel for LWRs has low thermal conductivity, which will be further reduced upon burn-up. The intrinsically low thermal transfer efficiency of the oxide fuels results in a large temperature gradient within the fuel pellet and high center-line temperature. Thermal swelling of the pellets and fission product accommodation and retention limit the lifetime of UO{sub 2} fuel in the reactor, presenting the great challenges for extending burn-up, effective utilization of nuclear resources and minimization of nuclear waste accumulation. Critical needs also exist in developing accident tolerant fuels that can tolerate loss of coolant accident or improve fuel performance under regular operation or beyond design scenario. Key properties of advanced fuels include high thermal conductivity, oxidation resistance, high temperature mechanical properties, fission gas retention capability and thus improved accident tolerance. The US Nuclear Energy Advanced Modeling and Simulation (NEAMS) program is developing science-based next generation fuel performance modeling capability as part its Fuel Product Line in order to facilitate the predictive capability of nuclear fuel performance and assist the design and analysis of reactor systems. Critical experimental data are needed to validate MARMOT models, particularly on effective thermal transport, fracture mechanisms, grain growth kinetics and fission gas behavior. The fabrication of sintered fuel pellets with well-controlled microstructure is prerequisite to establish the correlation of the microstructure features and fuel behavior in order to develop high fidelity fuel performance models. In this talk, recent advancements on developing advanced UO{sub 2} fuels and properties improvement are overviewed with the emphasis on different accident tolerant fuel (ATF) concepts and tailoring microstructures for MARMOT validation. Current efforts on ATFs include composite fuels and high-density fuels to improve thermal-mechanical properties and fission gas retention capabilities. Different composite UO{sub 2} fuels are fabricated with heterogeneous phases as sintering additives for microstructure and property control, and the potential application of the composites as advanced fuels with enhanced accident tolerance will be discussed. In addition, recent progresses of using field-assisted sintering technologies, specifically spark plasma sintering (SPS), in tailoring and engineering fuel matrix as the target systems for validating MARMOT physics models will be highlighted. Particularly, monolithic UO{sub 2} with tailored microstructure including grain size across multiple length scales from nano-metered to micron-sizes, porosity and stoichiometry can be sintered. The impacts of tailored microstructure on thermal-mechanical properties and grain growth kinetics are discussed within the context of the MARMOT modeling. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗