Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FILM BOILING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Method for the Collection, Gravimetric and Chemical Analysis of Nonvolatile Residue (NVR) on Surfaces

Nonvolatile residue (NVR), sometimes referred to as molecular contamination is the term used for the total composition of the inorganic and high boiling point organic components in particulates and molecular films deposited on critical surfaces surrounding space structures, with the particulate and NVR contamination originating primarily from pre-launch operations. The "nonvolatile" suggestion from the terminology NVR implies that the collected residue will not experience much loss under ambient conditions. NVR has been shown to have a dramatic impact on the ability to perform optical measurements from platforms based in space. Such contaminants can be detected early by the controlled application of various detection techniques and contamination analyses. Contamination analyses are the techniques used to determine if materials, components, and subsystems can be expected to meet the performance requirements of a system. Of particular concern is the quantity of NVR contaminants that might be deposited on critical payload surfaces from these sources. Subsequent chemical analysis of the contaminant samples by infrared spectroscopy and gas chromatography mass spectrometry identifies the components, gives semi-quantitative estimates of contaminant thickness, indicates possible sources of the NVR, and provides guidance for effective cleanup procedures. In this report, a method for the collection and determination of the mass of NVR was generated by the authors at NASA Langley Research Center. This report describes the method developed and implemented for collecting NVR contaminants, and procedures for gravimetric and chemical analysis of the residue obtained. The result of this NVR analysis collaboration will help pave the way for Langley's ability to certify flight hardware outgassing requirements in support of flight projects such as Stratospheric Aerosol and Gas Experiment III (SAGE III), Clouds and the Earth's Radiant Energy System (CERES), Materials International Space Station Experiment - X (MISSE-X), and Doppler Aerosol Wind Lidar (DAWN).

Gordon, Keith↗

Design and test of a compact optics system for the pool boiling experiment

The experiment described seeks to improve the understanding of the fundamental mechanisms that constitute nucleate pool boiling. The vehicle for accomplishing this is an investigation, including tests to be conducted in microgravity and coupled with appropriate analyses, of the heat transfer and vapor bubble dynamics associated with nucleation, bubble growth/collapse and subsequent motion, considering the interrelations between buoyancy, momentum and surface tension which will govern the motion of the vapor and surrounding liquid, as a function of the heating rate at the heat transfer surface and the temperature level and distribution in the bulk liquid. The experiment is designed to be contained within the confines of a Get-Away-Special Canister (GAS Can) installed in the bay of the space shuttle. When the shuttle reaches orbit, the experiment will be turned on and testing will proceed automatically. In the proposed Pool Boiling Experiment a pool of liquid, initially at a precisely defined pressure and temperature, will be subjected to a step imposed heat flux from a semitransparent thin-film heater forming part of one wall of the container such that boiling is initiated and maintained for a defined period of time at a constant pressure level. Transient measurements of the heater surface and fluid temperatures near the surface will be made, noting especially the conditions at the onset of boiling, along with motion photography of the boiling process in two simultaneous views, from beneath the heating surface and from the side. The conduct of the experiment and the data acquisition will be completely automated and self-contained. For the initial flight, a total of nine tests are proposed, with three levels of heat flux and three levels of subcooling. The design process used in the development and check-out of the compact photographic/optics system for the Pool Boiling Experiment is documented.

Ling, Jerri S.↗

Macro-to-microchannel transition in two-phase flow: Part 1 - Two-phase flow patterns and film thickness measurements

The classification of macroscale, mesoscale and microscale channels with respect to two-phase processes is still an open question. The main objective of this study focuses on investigating the macro-to-microscale transition during flow boiling in small scale channels of three different sizes with three different refrigerants over a range of saturation conditions to investigate the effects of channel confinement on two-phase flow patterns and liquid film stratification in a single circular horizontal channel (Part 2 covers the flow boiling heat transfer and critical heat flux). This paper presents the experimental two-phase flow pattern transition data together with a top/bottom liquid film thickness comparison for refrigerants R134a, R236fa and R245fa during flow boiling in small channels of 1.03, 2.20 and 3.04 mm diameter. Based on this work, an improved flow pattern map has been proposed by determining the flow patterns transitions existing under different conditions including the transition to macroscale slug/plug flow at a confinement number of Co {approx} 0.3-0.4. From the top/bottom liquid film thickness comparison results, it was observed that the gravity forces are fully suppressed and overcome by the surface tension and shear forces when the confinement number approaches 1, Co {approx} 1. Thus, as a new approximate rule, the lower threshold of macroscale flow is Co = 0.3-0.4 while the upper threshold of symmetric microscale flow is Co {approx} 1 with a transition (or mesoscale) region in-between. (author)

42 ENGINEERING↗

Film thickness measurement techniques applied to micro-scale two-phase flow systems

Recently semi-empirical models to estimate flow boiling heat transfer coefficient, saturated CHF and pressure drop in micro-scale channels have been proposed. Most of the models were developed based on elongated bubbles and annular flows in the view of the fact that these flow patterns are predominant in smaller channels. In these models, the liquid film thickness plays an important role and such a fact emphasizes that the accurate measurement of the liquid film thickness is a key point to validate them. On the other hand, several techniques have been successfully applied to measure liquid film thicknesses during condensation and evaporation under macro-scale conditions. However, although this subject has been targeted by several leading laboratories around the world, it seems that there is no conclusive result describing a successful technique capable of measuring dynamic liquid film thickness during evaporation inside micro-scale round channels. This work presents a comprehensive literature review of the methods used to measure liquid film thickness in macro- and micro-scale systems. The methods are described and the main difficulties related to their use in micro-scale systems are identified. Based on this discussion, the most promising methods to measure dynamic liquid film thickness in micro-scale channels are identified. (author)

42 ENGINEERING↗

Laser formation of luminescence bubble microstructures in polymer films

The results of laser-induced formation of luminescent structures on the surface of poly-2.2’-n-oxydiphenylene-5.5’-bis-benzimidazole films, obtained by the coating method from a formic acid solution, are presented. The structures are formed using cw 405-nm laser radiation with intensities of 10{sup 2} – 10{sup 4} W cm{sup –2}. It is shown (using methods of optical, atomic-force, and electron microscopy) that the structures formed on the surface are microbubble foam-like aggregations. Their formation is modelled as a sequence of the following processes: release of formic acid molecules, their condensation on matrix defects in the surface layer, and explosive boiling as a result of heating this layer of polymer film by the laser beam. The luminescence of these structures is due to the weakening of the concentration quenching from closely spaced luminescence centres in benzimidazole cycles during their emergence to the surface and the increase in the distance between them due to the extension on bubble aggregates on the surface. (interaction of laser radiation with matter. laser plasma)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dryout and Rewetting in the Pool Boiling Experiment Flown on STS-72 (PBE-2 B) and STS-77 (PBE-2 A)

Experiments were conducted in the microgravity of space in which a pool of liquid (R-113), initially at a precisely defined pressure and temperature, is subjected to a step imposed heat flux from a semi-transparent thin-film heater forming part of one wall of the container such that boiling is initiated and maintained for a defined period of time at a constant pressure level. A total of nine tests were conducted at three levels of heat flux and three levels of subcooling in each of the two space experiments in a GAS canister on the STS-77, -72, respectively. Three (3) modes of propagation of boiling across the heater surface and subsequent vapor bubble growths were observed, in addition to the two (2) modes observed in the previous microgravity pool boiling space flights on STS-47, -57, and -60. Of particular interest were the extremely dynamic or "explosive" growths, which were determined to be the consequence of the large increase in the liquid-vapor interface area associated with the appearance of a corrugated or rough interface. Predictions of circumstances for its onset have been carried out. Assumptions were necessary regarding the character of disturbances necessary for the instabilities to grow. Also, a new vapor bubble phenomena was observed in which small vapor bubbles migrated toward a larger bubble, eventually coalescing with this larger bubble. The heat transfer was enhanced approximately 30% as a result of these migrating bubbles, which is believed to be a vapor bubble manifestation of Marangoni convection and/or molecular momentum effects, sometimes referred to as vapor recoil. The circumstances of heat flux and liquid subcooling necessary to produce heater surface dryout for an initially stagnant liquid subjected to an imposed heat flux have been more closely identified.

Merte, Herman, Jr.↗

EVAPORATIVE FILM COOLING FOR HYPERSONIC REENTRY VEHICLES

Evaporative film cooling on blunt nose models has been investigated in a 12″ × 12″ hypersonic blowdown wind tunnel at Mach number 7 with stagnation temperatures up to 2500 °R. Water as coolant was supplied continuously through orifices located near the stagnation point of a hemisphere-cylinder body (3 inch diameter) and a blunt cone with 10° half angle (base diameter 5.5 inches) forming an evaporating water film covering the body. This results in nearly uniform wall temperatures about 30 °R below the local boiling temperature of the water.

SPACE SCIENCE↗

Solution-Processed Layered Gallium Telluride Thin-Film Photodetectors

Using scalable solution processing, layered gallium telluride (GaTe) nanoflake dispersions are produced in surfactant-free, low-boiling-point, water–ethanol cosolvent mixtures. During exfoliation, chemical degradation of the ambient-reactive GaTe crystals is minimized by using deoxygenated solvents in a sealed tip ultrasonication system. The structural and chemical integrity of the solution-processed GaTe nanoflakes is subsequently confirmed with a comprehensive suite of microscopic and spectroscopic analyses. Furthermore, field-effect transistors and phototransistors based on individual solution-processed GaTe nanoflakes show electronic and optoelectronic properties, respectively, that are comparable to micromechanically exfoliated GaTe. Minimal solution-processing residues from the surfactant-free, low-boiling-point cosolvent dispersion medium coupled with the high intrinsic hole doping of GaTe produces the highest electrical conductivity among solution-processed layered nanoflake thin films without post-treatment. Large-area photodetectors based on these electrically percolating thin films of solution-processed GaTe nanoflakes show a positive correlation between responsivity and illumination intensity, with a high photoconversion gain that is explained by a combination of defect-mediated optical processes and photothermal effects. Finally, overall, this study establishes solution-processed layered GaTe nanoflakes as a leading candidate for high-performance, large-area, thin-film photodetectors.

47 OTHER INSTRUMENTATION↗

Low velocity nucleate flow boiling at various orientations

Subcooled forced convection nucleate boiling experiments with R-113 were conducted at low velocities using both thin film semi-transparent gold on quartz and gold coated cooper substrate flat heaters at varying orientations. The results are intended to assist in understanding effects of buoyancy in forced convection boiling and in better defining requirements for studying flow boiling in the microgravity environment of space. Measurements of the heat flux and the surface superheat were made at three levels of subcooling from 2.2 C to 11.1 C, four bulk velocities from 4.1 cm/s to 32.4 cm/s and various orientations spanning 360 deg. The experiments demonstrate that if buoyancy is significant reative to bulk liquid momentum, then a decrease in the buoyant force normal and away from the heater surface enhances the heat transfer, with the effect being most prominent at low values of heat flux. Furthermore, the effect of velocity is shown to be dependent on the surface orientation.

Kirk, Kevin M.↗

Thermal effects in two-phase flow through face seals

When liquid is sealed at high temperature, it flashes inside the seal due to pressure drop and/or viscous heat dissipation. Two-phase seals generally exhibit more erratic behavior than their single phase counterparts. Thermal effects, which are often neglected in single phase seal analyses, play an important role in determining seal behavior under two-phase operation. It is necessary to consider the heat generation due to viscous shear, conduction into the seal rings and convection with the leakage flow. Analytical models developed work reasonably well at the two extremes - for low leakage rates when convection is neglected and for higher leakage rates when conduction is neglected. A preliminary model, known as the Film Coefficient Model, is presented which considers conduction and convection both, and allows continuous boiling over an extended region unlike the previous low-leakage rate model which neglects convection and always forces a discrete boiling interface. Another simplified, semi-analytical model, based on the assumption of isothermal conditions along the seal interafce, has been developed for low leakage rates. The Film Coefficient Model may be used for more accurate and realistic description.

Basu, Prithwish↗

Evaporative thermal resistance and its influence on microlayer evaporation

The ability to predict various aspects of boiling is important for both safety and design of water-cooled reactors. Component-scale modelling is necessarily done by semi-mechanistic, semi-empirical approaches, generally based on heat flux partitioning. This needs to be informed by multiple detailed experimental observations of boiling behavior. Such measurements are difficult to make, and much effort is being applied to microscopic computational modelling of the detailed boiling process. Aims of such activities include the mechanistic prediction of growth and detachment of one bubble during nucleate boiling, and the quantification of the associated heat transfer partitioning (evaporation, micro-convection, quenching). We here study a subset of the full problem, and focus on the thermal response of the boiling substrate to the early growth of a single vapour bubble during pool boiling of water at atmospheric pressure. In such conditions, a thin liquid film ('microlayer') is left behind beneath the bubble as this expands. The microlayer evaporates due to the temperature difference between the solid-liquid and vapour-liquid interface. Its thickness being small, of order of microns, the local evaporation rate per unit area of bubble base can be high, up to one kilogram per second. Microlayer evaporation can therefore be important in early stages of bubble growth. In this contribution, thermal response of the boiling substrate to microlayer evaporation is studied with a two-dimensional, axisymmetric transient conduction model, coupled with an algebraic sub-model of the liquid film. The flow of heat through the microlayer is modelled as conduction in the liquid and with a pseudo-convective 'evaporative' heat transfer coefficient at the liquid-vapor interface, accounting for the interface superheat driving the evaporation process. Thermal coupling (conjugate heat transfer) between microlayer and solid substrate is obtained with a time dependent non-homogeneous Neumann boundary condition, derived from the algebraic microlayer sub-model and applied at the top surface of the solid computational domain. The thermal resistance associated to the evaporative heat transfer mechanism is shown to depend on a highly uncertain parameter, termed an 'evaporation coefficient'. After some exploratory calculations of the likely importance of the evaporative resistance in the present context, the model is employed to interpret some recent microlayer measurements. Satisfactory agreement between computed and measured evolution of the microlayer profile is obtained if small values (between 0.01 and 0.10) of the evaporation coefficient are used. The order of magnitude of the predicted evaporation rate from the microlayer is consistent with experimental observations. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Evaluation of polyimide films as adhesives

A commercially available LARC-TPI film and an experimentally prepared film of LARC-TPI with 5 mol pct of 4,4-prime-oxydianiline (ODA), designated as LARC-TPI/ODA, were evaluated as thermoplastic adhesive films for bonding Ti-6Al-4V. Lap shear strength was used to evaluate the materials as adhesives. They were characterized after fracture by determining the glass transition temperature, T(g). The mode of failure is also reported. Thermal exposure at 240 C for 500 and 1000 h and a 72-h water-boil were conducted on lap shear specimens prepared with the two adhesive films. Lap shear tests were conducted at room temperature, 177 C, 204 C, and 232 C before and after exposures.

Progar, Donald J.↗

Enhancing the Solubility of Semiconducting Polymers in Eco-Friendly Solvents with Carbohydrate-Containing Side Chains

Semiconducting polymers are at the forefront of next-generation organic electronics due to their robust mechanical and optoelectronic properties. However, their extended π-conjugation often leads to materials with low solubilities in common organic solvents, thus requiring processing in high-boiling-point and toxic halogenated solvents to generate thin-film devices. To address this environmental concern, a natural product-inspired side-chain engineering approach was used to incorporate galactose-containing moieties into semiconducting polymers toward improved processability in greener solvents. Novel isoindigo-based polymers with different ratios of galactose-containing side chains were synthesized to improve the solubilities of the organic semiconductors in alcohol-based solvents. The addition of carbohydrate-containing side chains to π-conjugated polymers was found to considerably impact the intermolecular aggregation of the materials and their microstructures in the solid state as confirmed by atomic force microscopy and grazing-incidence wide-angle X-ray scattering. The charge transport characteristics of the new semiconductors were evaluated by the fabrication of organic field-effect transistors prepared from both toxic halogenated and greener alcohol-based solvents. Importantly, the incorporation of carbohydrate-containing side chains was shown to have very little detrimental impact on the electronic properties of the polymer when processed from green solvents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The hydrodynamics of the formation of microlayers beneath vapour bubbles growing on a heated substrate

Thin layers of liquid are known to be 'left behind' beneath essentially the entire extent of the (approximately) hemispherical bubbles that grow rapidly at low pressures on heated substrates. The formation of these 'microlayers' has been well established by modern sophisticated experimental observations. Whilst the rapid evaporation of these layers can make a dominant contribution to the formation and growth of these bubbles, their effect is incorporated into CFD boiling analysis via semiempirical 'sub-grid scale' modelling, and the physics of the formation and the prediction of the characteristics of the microlayers have received little attention. We present here an investigation into their formation via the solution of the full Navier Stokes equations for viscous flow. This investigation has allowed us to demonstrate that the overall extent of the micro-layer is a function of the balance of inertial and surface tension forces that control the macroscopic expansion of the bubble. The inertial effects inhibit the growth of the bubble away from the wall, and force it to adopt a more hemispherical shape, with a larger 'contact' area with the substrate. Beneath this 'contact' area a micro-layer is formed by liquid being left behind as the bubble grows. The depth of the micro-layer left behind seems to depend largely upon the viscous forces at work in the flow near the wall. (authors)

42 ENGINEERING↗

Adhesive evaluation of thin films of LARC-TPI and LARC-TPI with 5 mol % ODA

A commercially available LARC-TPI film and an experimentally prepared film of LARC-TPI with 5 mol % of 4,4'-oxydianiline (ODA), designated as LARC-TPI/ODA in the report, supplied by Mitsui Toatsu Chemicals, Incorporated (MTCI), Japan, were evaluated as thermoplastic adhesive films for bonding Ti-6Al-4V. The LARC-TPI/ODA had been shown by MTCI to possess more flow than thermoplastic LARC-TPI and was, therefore, evaluated and compared to the LARC-TPI. Lap shear strength was used to evaluate the materials as adhesives. They were characterized after fracture by determining the glass transition temperature, Tg. The mode of failure was also reported. Thermal exposure at 204C for 500 and 1000 hrs and a 72-hour water-boil were conducted on lap shear specimens prepared with the two adhesive films. Lap shear tests were conducted at RT, 177C, 204C, and 232C before and after exposures.

Progar, D. J.↗

Transient pool boiling in microgravity

Transient nucleate pool boiling experiments using R113 are conducted for short times in microgravity and in earth gravity with different heater surface orientations and subcoolings. The heating surface is a transparent gold film sputtered on a quartz substrate, which simultaneously provides surface temperature measurements and permits viewing of the boiling process from beneath. For the microgravity experiments, which have uniform initial temperatures and no fluid motion, the temperature distribution in the R 113 at the moment of boiling inception is known. High speed cameras with views both across and through the heating surface record the boiling spread across the heater surface, which is classified into six distinct categories.

Ervin, J. S.↗