Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineering, Lasers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Reduction of ETS-VI Laser Communication Equipment Optical-Downlink Telemetry Collected During GOLD

Free-space laser communications experiments were conducted between the laser communication equipment (LCE) on board the Japanese Engineering Test Satellite VI (ETS-VI) and the ground station located at the Table Mountain Facility (TMF) during late 1995 and early 1996. This article describes the on-line data reduction process used to decode LCE telemetry (called E2) downlinked on the optical carrier during the Ground/Orbiter Lasercomm Demonstration (GOLD) experiments. The LCE has the capability of transmitting real-time sensor and status information at 128 kbps by modulating the onboard diode laser. The optical downlink was detected on the ground, bit synchronized, and the resulting data stream stored on a data recorder. The recorded data were subsequently decoded by on-line data processing that included cross-correlation of the known telemetry data format and the downlink data stream. Signals obtained from the processing can be useful not only in evaluating the characteristics of the LCE but also in understanding uplink and downlink signal quality.

Toyoshima, M.↗

Future technologies for lidar/DIAL remote sensing

Several technology needs for future space-based lidar/DIAL applications are outlined in connection with Mission to Planet Earth. First, approved laser radar missions included in Mission to Planet Earth are outlined with emphasis on engineering developments at the NASA Langley Research Center. The current status of solid-state laser materials is then presented with particular reference to those materials that will lead to the development of a 2-micron technology for a variety of wind sensing applications. Finally, recommendations are given for accelerated technology development which will lead to laser radar experiments from space to improve scientific understanding of atmospheric chemistry and dynamics, the greenhouse effect, and improvements in measurements of meteorological parameters.

Allario, Frank↗

Optics in engineering measurement; Proceedings of the Meeting, Cannes, France, December 3-6, 1985

The present conference on optical measurement systems considers topics in the fields of holographic interferometry, speckle techniques, moire fringe and grating methods, optical surface gaging, laser- and fiber-optics-based measurement systems, and optics for engineering data evaluation. Specific attention is given to holographic NDE for aerospace composites, holographic interferometry of rotating components, new developments in computer-aided holography, electronic speckle pattern interferometry, mass transfer measurements using projected fringes, nuclear reactor photogrammetric inspection, a laser Doppler vibrometer, and optoelectronic measurements of the yaw angle of projectiles.

Fagan, William F.↗

Performance and heat transfer characteristics of the laser-heated rocket - A future space transportation system

The application of advanced liquid-bipropellant rocket engine analysis techniques has been utilized for prediction of the potential delivered performance and the design of thruster wall cooling schemes for laser-heated rocket thrusters. Delivered specific impulse values greater than 1000 lbf-sec/lbm are potentially achievable based on calculations for thrusters designed for 10-kW and 5000-kW laser beam power levels. A thruster wall-cooling technique utilizing a combination of regenerative cooling and a carbon-seeded hydrogen boundary layer is presented. The flowing carbon-seeded hydrogen boundary layer provides radiation absorption of the heat radiated from the high-temperature plasma. Also described is a forced convection thruster wall cooling design for an experimental test thruster.

Shoji, J. M.↗

Matera Laser Ranging Observatory (MLRO): An overview

The Agenzia Spaziale Italiana (ASI) is currently under negotiation with the Bendix Field Engineering Corporation (BFEC) of the Allied Signal Aerospace Company (ASAC) to build a state-of-the-art laser ranging observatory for the Centro di Geodesia Spaziale, in Matera, Italy. The contract calls for the delivery of a system based on a 1.5 meter afocal Cassegrain astronomical quality telescope with multiple ports to support a variety of experiments for the future, with primary emphasis on laser ranging. Three focal planes, viz. Cassegrain, Coude, and Nasmyth will be available for these experiments. The open telescope system will be protected from dust and turbulence using a specialized dome which will be part of the building facilities to be provided by ASI. The fixed observatory facility will be partitioned into four areas for locating the following: laser, transmit/receive optics, telescope/dome enclosure, and the operations console. The optical tables and mount rest on a common concrete pad for added mechanical stability. Provisions will be in place for minimizing the effects of EMI, for obtaining maximum cleanliness for high power laser and transmit optics, and for providing an ergonomic environment fitting to a state-of-the-art multipurpose laboratory. The system is currently designed to be highly modular and adaptable for scaling or changes in technology. It is conceived to be a highly automated system with superior performance specifications to any currently operational system. Provisions are also made to adapt and accommodate changes that are of significance during the course of design and integration.

Varghese, Thomas K.↗

Airbreathing propulsion component technologies

The article suggests that the 1980's will see significant improvements in virtually all gas-turbine engine components and their materials and structural design methods. These improvements will be made possible by improved theoretical models, laser Doppler measurement techniques, advances in rotor-spool technology, the evolution of engine controls, etc. It is suggested that the engine components field should expect broad and steady advances in the technologies of flow, materials, and structures in terms of scope, precision, and tools of design.

Rosen, C.↗

Independent Reliability Assessment of the Laser Transmitter for the ESA-NASA Laser Interferometer Space Antenna (LISA) Program

As part of the laser development process, NASA’s Goddard Space Flight Center (GSFC) requested support from the NASA Engineering and Safety Center (NESC) to independently assess the Technology Readiness Level (TRL) of the LISA Laser System (LS). The independent assessment included the following tasks: (a) assess the design for weaknesses and suggest improvements to mitigate risks, (b) assess the laser reliability plan for weaknesses and suggest improvements to mitigate risks and improve effectiveness, and (c) assess the current redundancy plan on laser subsystems for weaknesses and suggest improvements to mitigate risks and improve effectiveness. The presentation will focus on the assessment findings and the current development progress of the LISA laser to meet the mission requirements with a delivery of a form, fit, and functional TRL6 laser to the LISA mission by late 2023.

Laser Interferometry↗

Bimetallic Channel Wall Nozzle Development and Hot-Fire Testing Using Additively Manufactured Laser Wire Direct Closeout Technology

NASA has been developing and advancing regeneratively-cooled channel wall nozzle technology for liquid rocket engines to reduce cost and schedules associated with fabrication. One of the primary methods being advanced is Laser Wire Direct Closeout (LWDC). LWDC was developed to provide an additively manufactured laser deposited closeout of the coolant channels that also forms the structural jacket in-situ. This technique has been previously demonstrated through process development and hot-fire testing on a series of subscale nozzles at NASA Marshall Space Flight Center. The hot-fire test articles were fabricated using monolithic alloys to simplify the fabrication process. Ongoing research is being conducted to further expand use of this process for increased scale and bimetallic or multi-alloy options. The use of multi-alloys is desired to fully optimize the combination of materials in the radial and axial directions to reduce overall weight of the nozzle and allow for higher thermal and structural margins on the channel wall nozzle. NASA recently completed process development and hot-fire testing of a series of channel wall nozzles that incorporate a copper-alloy as the hotwall liner material and a superalloy and combination thereof for the structural jacket using the LWDC technique. The fabrication process was further advanced by using a multi-alloy axial joint using explosive bonding integrating a copper-alloy at the forward end of the nozzle hotwall and a stainless-alloy for the remaining length. A third alloy was then used for the channel closeout using the LWDC process. This paper will describe the process development using the LWDC process for channel closeout utilizing the multi-alloys, hardware design and results from hot-fire testing on subscale multi-alloy LWDC channel cooled nozzles.

Gradl, Paul↗

The ILRS: Approaching 20 Years and Planning for the Future

The International Laser Ranging Service (ILRS) was established by the International Association of Geodesy (IAG) in 1998 to support programs in geodesy, geophysics, fundamental constants and lunar research, and to provide the International Earth Rotation Service with data products that are essential to the maintenance and improvement in the International Terrestrial Reference Frame (ITRF), the basis for metric measurements of changes in the Earth and Earth–Moon system. Other scientific products derived from laser ranging include precise geocentric positions and motions of ground stations, satellite orbits, components of Earth’s gravity field and their temporal variations, Earth Orientation Parameters, precise lunar ephemerides and information about the internal structure of the Moon. Laser ranging systems are already measuring the one-way distance to remote optical receivers in space and are performing very accurate time transfer between remote sites in the Earth and in Space. The ILRS works closely with the IAG’s Global Geodetic Observing System. The ILRS develops (1) the standards and specifications necessary for product consistency, and (2) the priorities and tracking strategies required to maximize network efficiency. The service collects, merges, analyzes, archives and distributes satellite and lunar laser ranging data to satisfy a variety of scientific, engineering, and operational needs and encourages the application of new technologies to enhance the quality, quantity, and cost effectiveness of its data products. The ILRS works with (1) new satellite missions in the design and building of retroreflector targets to maximize data quality and quantity, and (2) science programs to optimize scientific data yield. Since its inception, the ILRS has grown to include forty laser ranging stations distributed around the world. The ILRS stations track more than ninety satellites from low Earth orbit (LEO) to the geosynchronous orbit altitude as well as retroreflector arrays on the surface of the Moon. Applications have been expanded to include time transfer, asynchronous ranging for targets at extended ranges, free space quantum telecommunications, and the tracking of space debris. Laser ranging technology is moving to lower energy, higher repetition rates (kHz), single-photon-sensitive detectors, shorter pulse widths, shorter normal point intervals for faster data acquisition, and increased pass interleaving, automated to autonomous operation with remote access, and embedded software for real-time updates and decision making. An example of pass interleaving is presented for the Yarragadee station (see Fig. 4); tracking of LEO satellites is often accommodated during break in LEO and GNSS passes. New satellites arrays provide more compact targets and work continues on the development of lighter less expensive arrays for satellites and the moon. The service now provides operational ITRF products including daily/ weekly station positions and daily resolution Earth orientation products; the flow of weekly combination of satellite orbit files for LAGEOS/Etalon-1 and -2 has recently been established. New products are under testing through a pilot project on systematic error monitoring currently underway. The article will give an overview of activities underway within the service, paths forward presently envisioned, and current issues and challenges.

Laser retroreflectors↗

Airborne laser topographic mapping results

The results of terrain mapping experiments utilizing the National Aeronautics and Space Administration (NASA) Airborne Oceanographic Lidar (AOL) over forested areas are presented. The flight tests were conducted as part of a joint NASA/U.S. Army Corps of Engineers (CE) investigation aimed at evaluating the potential of an airborne laser ranging system to provide cross-sectional topographic data on flood plains that are difficult and expensive to survey using conventional techniques. The data described in this paper were obtained in the Wolf River Basin located near Memphis, TN. Results from surveys conducted under winter 'leaves off' and summer 'leaves on' conditions, aspects of day and night operation, and data obtained from decidous and coniferous tree types are compared. Data processing techniques are reviewed. Conclusions relative to accuracy and present limitations of the AOL, and airborne lidar systems in general, to terrain mapping over forested areas are discussed.

Krabill, W. B.↗

Promoting Robust Design of Diode Lasers for Space: A National Initiative

The Diode-laser Array Working Group (DAWG) is a national-level consumer/provider forum for discussion of engineering and manufacturing issues which influence the reliability and survivability of high-power broad-area laser diode devices in space, with an emphasis on laser diode arrays (LDAs) for optical pumping of solid-state laser media. The goals of the group are to formulate and validate standardized test and qualification protocols, operational control recommendations, and consensus manufacturing and certification standards. The group is using reliability and lifetime data collected by laser diode manufacturers and the user community to develop a set of standardized guidelines for specifying and qualifying laser diodes for long-duration operation in space, the ultimate goal being to promote an informed U.S. Government investment and procurement strategy for assuring the availability and durability of space-qualified LDAs. The group is also working to establish effective implementation of statistical design techniques at the supplier design, development, and manufacturing levels to help reduce product performance variability and improve product reliability for diodes employed in space applications

Tratt, David M.↗

State of the art in the detection of intelligent extraterrestrial signals.

Recent progress in ideas of how signals that might represent electromagnetic radiations of intelligent civilizations elsewhere in the galaxy is summarized. Project Cyclops, carried out at Ames Research Center under the auspices of NASA and the American Society for Engineering Education, determined that microwaves are superior to lasers for interstellar signalling. It is felt that the band lying between the resonances of the two dissociation products of water, the hydrogen line at 1420 MHz, and the first hydroxyl line at 1662 MHz, is the most suitable. Phased antenna arrays of perhaps 1000 to 10,000 dishes of 100 m diam would be required. It is considered that a list of likely stars should be compiled, and these should be searched one at a time. Procedures for combing the spectrum are outlined.

Oliver, B. M.↗

Nondestructive evaluation of structural ceramics

Research on nondestructive evaluation (NDE) of structural ceramics for heat engine applications is reviewed. Microfocus radiography and scanning laser acoustic microscopy are the NDE techniques highlighted. The techniques were applied to research samples of sintered silicon nitride and silicon carbide in the form of modulus-of-rupture (MOR) bars. The strength and limitations of the aforementioned techniques are given in terms of probablility of detection for voids in green and sintered MOR bars. Voids for this purpose were introduced by seeding green ceramic bars and characterizing each void in terms of its size, shape, location, and nature before and after sintering. The effects of material density, microstructure, surface finish, thickness, void depth, and size characteristics on detectability are summarized.

Vary, Alex↗

Ge's Mobile, Coherent Doppler Lidar Test/Ealuation Facilities

The primary objective of this independent research and development (IR and D) program in support of the Laser Atmospheric Wind Sounder (LAWS) program is to develop and evaluate technologies with direct applications to spaceborne laser wind sensing, and to develop system level engineering experience in designing, operating, and modeling a coherent Doppler lidar. GE is developing a mobile, ground based coherent Doppler lidar as an end-to-end system level test facility to evaluate applicable technologies, verify system level performance issues, perform instrument calibration, and validate end-to-end system performance model predictions. Here, the primary focus is on a description of the ground based lidar system and the performance during the initial shakedown operation after system integration.

Sroga, J. T.↗

The Apollo Lightcraft Project

The overall goal for this NASA/USRA-sponsored 'Apollo Lightcraft Project' is to develop a revolutionary launch vehicle technology that can reduce payload transport costs by a factor of 1000 below the Space Shuttle Orbiter. The RPI design team proposes to utilize advanced, highly energetic, beamed-energy sources (laser, microwave) and innovative combined-cycle (airbreathing/rocket) engines to accomplish this goal. This second year focused on systems integration and analysis of the 'Apollo Lightcraft'. This beam-powered, single-stage-to-orbit vehicle is envisioned as the globe-trotting family shuttlecraft of the 21st century. Detailed investigations of the Apollo Lightcraft Project during the second year of study helped evolve the propulsion system design, while focusing on the following areas: (1) man/machine interface; (2) flight control systems; (3) power beaming system architecture; (4) reentry aerodynamics; (5) shroud structural dynamics; and (6) optimal trajectory analysis.

Source record↗

Pump CFD code validation tests

Pump CFD code validation tests were accomplished by obtaining nonintrusive flow characteristic data at key locations in generic current liquid rocket engine turbopump configurations. Data were obtained with a laser two-focus (L2F) velocimeter at scaled design flow. Three components were surveyed: a 1970's-designed impeller, a 1990's-designed impeller, and a four-bladed unshrouded inducer. Two-dimensional velocities were measured upstream and downstream of the two impellers. Three-dimensional velocities were measured upstream, downstream, and within the blade row of the unshrouded inducer.

Brozowski, L. A.↗

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. The near-net shape DMLS parts have been delivered and final machining is underway. Fabrication of the traditionally manufactured hardware is also proceeding. Testing in liquid oxygen is planned for Q2 of FY2017. This topic explores the design of the turbopump along with fabrication and material testing of the DMLS hardware.

O'Neal, Derek↗

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. This paper discusses the impacts of the DMLS fabrication technique on the design of the turbopump and lessons learned during DMLS hardware fabrication and material testing.

O’Neal, T. Derek↗