SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Development of cathodic electrocatalysts for use in low temperature hydrogen-oxygen fuel cells with alkaline electrolyte
The controlled oxidation in air of Raney nickel electrocatalysts was studied, with special attention paid to the quantitative analysis of nickel hydroxide. The content of the latter was determined through X-ray studies, thermogravimetric measurements, and spectral photometric examinations. The dependence of the content on the drying of activated catalyst is determined. The influence of nickel hydroxide on the electrochemical parameters of the catalyst, such as diffusion polarization, is studied, including a measurement of the exchange current density using the potential drop method. Conservation by oxidation in air with ancillary stabilization of the oxide in an H2 flow at 300 C is explored, including reduction by H2, the influence of tempering time, and structural studies on conserved and stabilized catalyst, long term research on the catalyst, including the influence of aging on the reduced catalyst, and the results of impedance measurements are presented.
A significant increase in energy density may be possible if a two-unit alkaline regenerative H2-O2 fuel cell is replaced with a single-unit system that uses passive means for H2O transfer and thermal control. For this single-unit system, new electrocatalysts for the O2 electrode will be required which are not only bifunctionally active but also chemically and electrochemically stable between the voltage range of about 0.7 and 1.5 V. NiCo2O4 spinel is reported to have certain characteristics that make it useful for a study of electrode fabrication techniques. High surface area NiCo2O4 powder was fabricated into unsupported, bifunctional, PTFE-bonded, porous gas fuel cell electrodes by commercial sources using varying PTFE contents and sintering temperatures. The object of this study is to measure the bifunctional activities of these electrodes and to observe what performance differences might result from different commercial electrode fabricators. O2 evolution and O2 reduction data were obtained at 80 C (31 percent KOH). An irreversible reaction (i.e., aging) occurred during O2 evolution at potentials greater than about 1.5 V. Anodic Tafel slopes of 0.06 and 0.12 V/decade were obtained for the aged electrodes. Within the range of 15 to 25 percent, the PTFE content was not a critical parameter for optimizing the electrode for O2 evolution activity. Sintering temperatures between 300 and 340 C may be adequate but heating at 275 C may not be sufficient to properly sinter the PTFE-NiCo2O4 mixture. Electrode disintegration was observed during O2 reduction. Transport of O2 to the NiCo2O4 surface became prohibitive at greater than about -0.02 A/sq cm. Cathodic Tafel slopes of -0.6 and -0.12 V/decade were assumed for the O2 reduction process. A PTFE content of 25 percent (or greater) appears to be preferable for sintering the PTFE-NiCo2O4 mixture.
In most instances separate electrocatalysts are needed to promote the reduction of O2 in the fuel cell mode and to generate O2 in the energy storage-water electrolysis mode in aqueous electrochemical systems operating at low and moderate temperatures (T greater than or equal to 200 C). Interesting exceptions are the lead and bismuth ruthenate pyrochlores in alkaline electrolytes. These catalysts on high area carbon supports have high catalytic activity for both O2 reduction and generation (1,2). Rotating ring-disk electrode measurements provide evidence that the O2 reduction proceeds by a parallel four-electron pathway. The ruthenates can also be used as self-supported catalysts to avoid the problems associated with carbon oxidation, but the electrode performance so far achieved in the research at Case Western Reserve University (CWRU) is considerably less. At the potentials involved in the anodic mode the ruthenate pyrochlores have substantial equilibrium solubility in concentrated alkaline electrolyte. This results in the loss of catalyst into the bulk solution and a decline in catalytic activity. Furthermore, the hydrogen generation counter electrode may become contaminated with reduction products from the pyrochlores (lead, ruthenium). A possible approach to this problem is to immobilize the pyrochlore catalyst within an ionic-conducting solid polymer, which would replace the fluid electrolyte within the porous gas diffusion O2 electrode. For bulk alkaline electrolyte, an anion-exchange polymer is needed with a transference number close to unity for the Oh(-) ion. Preliminary short-term measurements with lead ruthenates using a commercially available partially-fluorinated anion-exchange membrane as an overlayer on the porous gas-fed electrode indicate lower anodic polarization and virtually unchanged cathodic polarization.
Carbons activated with macrocyclics have attracted increasing attention as alternative electrocatalysts for oxygen reduction. Initial activity of these catalysts is good, but performance declines rapidly. Pyrolyzing the macrocyclic on the carbon support leads to enhanced stability and the catalysts retain good activity. The approach described is designed to develop bulk doped catalysts with similar structures to pyrolyzed macrocyclic catalysts. The transition metal and coordinated ligands are dispersed throughout the bulk of the conductive carbon skeleton. Two approaches to realizing this concept are being pursued, both involving the doping of carbon precursors. In one approach, the precursor is a solid phase carbon-containing ion-exchange resin. The precursor is doped with a transition metal and/or nitrogen, and the resulting mixture is pyrolyzed. In the other approach, the precursor is a gas-phase hydrocarbon. This is introduced with a transition metal species and nitrogen species into a reactor and pyrolyzed. Several studies have been conducted to determine if there is a synergistic effect between the transition metal and nitrogen and the effect of different methods of introducing the metal-nitrogen (M-N) coordination on performance. One approach was to introduce the metal and nitrogen separately, for example, by sequentially doping FeCl3 and NH4OH into the resin. Catalysts were prepared from an undoped ion-exchange resin, a resin doped only with N, a resin doped only with Fe, and a resin doped with both Fe and N. Introduction of nitrogen alone has no beneficial effect on the performance of the catalysts. The introduction of the Fe alone significantly improves the performance in both the high and low current density regions. When both Fe and N are introduced, the performance at lower current densities (catalytic activity) is increased beyond that of the Fe-doped carbon, but the performance at higher current densities is similar to the carbon containing only Fe. Catalysts prepared from resins-Fe(bipy)3SO4 precursors have performance that is only slightly less then CoTMPP adsorbed and pyroloyzed on Vulcan XC-72. Their performance is much better than carbons which have had the N and Fe introduced separately.
Platinum-cored ferritins were synthesized as electrocatalysts by electrochemical biomineralization of immobilized apoferritin with platinum. The platinum cored ferritin was fabricated by exposing the immobilized apoferritin to platinum ions at a reduction potential. On the platinum-cored ferritin, oxygen is reduced to water with four protons and four electrons generated from the anode. The ferritin acts as a nano-scale template, a biocompatible cage, and a separator between the nanoparticles. This results in a smaller catalyst loading of the electrodes for fuel cells or other electrochemical devices. In addition, the catalytic activity of the ferritin-stabilized platinum nanoparticles is enhanced by the large surface area and particle size phenomena. The work presented herein details the immobilization of ferritin with various surface modifications, the electrochemical biomineralization of ferritin with different inorganic cores, and the fabrication of self-assembled 2-D arrays with thiolated ferritin.
Electrocatalysts composed of single atoms or metal clusters dispersed over porous carbon support were prepared by a lithium-melt method. The new catalysts demonstrated high selectivity, high Faradic efficiency and low overpotential toward to the electrocatalytic reduction of carbon dioxide to chemicals.
Not Available
Electrochemical hydrogenation of nitrate to ammonia using renewable electricity is a promising route for sustainability but lacks catalysts that can deliver balanced selectivity, activity, and durability. For this work, a new family of noble metal-free and high-performing Chevrel phase Ni 2 Mo 6 T 8 (T = S, Se, and Te) catalysts that have similar structural and textural properties and differ presumably only in chalcogenide anion is systematically studied. The side-by-side comparisons allow the uncovering of the critical roles of chalcogenide anions in impacting kinetic activities and long-term durability. The incorporation of anions with larger size and smaller electronegativity from sulfide to selenide and telluride invokes stronger inhibition of the otherwise competing hydrogen evolution reaction (HER) and steers the hydrogenation toward the selective formation of ammonia, thus improving both Faradic selectivity and the turnover frequency to high levels of 99.4% and 21.5 s –1 , respectively, on the Ni 2 Mo 6 Te 8 catalyst. More significantly, the bulkier anion in the Ni 2 Mo 6 T 8 catalyst kinetically inhibited the intercalation of electrolyte cations, a major degradation mechanism in the catalyst family examined here and delivered several times improved durability. Therefore, this study introduces novel active motifs for selective nitrate reduction and provides insights into the catalyst degradation mechanism and practical ways to improve durability.
Water oxidation is an important reaction studied as a way to generate electrons from water, to promote water splitting and the formation of green hydrogen. When using electrodes to drive homogeneous water oxidation catalysis, cyclic voltammograms are analyzed to provide catalytic rate constants. There are two main methods, foot-of-the-wave analysis (FOWA) and limiting current analysis. FOWA relies on approximations inherent to analyzing water oxidation catalysis, such as determining the formal potential of the catalytic intermediate, E 0 cat . Limiting current methods are the optimal way to analyze catalyst performance but rely on observable limiting current, which is virtually never seen in water oxidation. To avoid those issues, a method is proposed for analyzing nonideal cyclic voltammetry waveshapes in water oxidation: by analyzing rate data across a large range of potentials, an optimal potential, E 0 cat , can be obtained, where catalytic current, i cat , is nearly independent of scan rate and has a linear dependency on buffer concentration. Here, the method is applied to four homogeneous water oxidation catalysts with prior extensive electrochemical elucidation, all of which lack an ideal, purely kinetic waveshape in cyclic voltammetry. Application of the method avoids the biases of the other methods cited for the kinetic analyses of water oxidation catalysts.
The electrochemical ammonia oxidation reaction (AOR) is a promising anodic reaction for hydrogen production, offering a lower theoretical potential compared to oxygen evolution reaction. Despite this thermodynamic advantage, AOR suffers from sluggish multi-electron transfer reaction kinetics and the regeneration of catalytically active Ni 3+ species, which limits both activity and durability. In this study, amorphous NiCu bimetallic catalysts were prepared via facile precipitating metal nitrate deposition (PMND) method. The addition of Cu induces a robust Ni 2+ /Ni 3+ transition, stabilizing catalytically active Ni 3+ species and modulating the electronic structure of Ni. It alters the oxidation and desorption behavior of nitrogen-containing intermediates and facilitating their conversions to NO x species, resulting in fast active site regeneration. Furthermore, amorphous structure provides abundant dangling bonds, which enhances the intrinsic reactivity and accessibility of active sites rather than increasing the number of active sites. As a result, these effects accelerate the overall reaction kinetics. The optimized NiCu 5:1 catalyst achieved an ammonia removal efficiency of ∼100 % and a hydrogen production rate of 2.45 mmol/(h∙cm 2 ) at 1.6 V RHE .
Materials degradation is a major factor that limits the wider adoption of renewable and clean energy technologies. This is particularly true for the Pt group metal-free (PGM-free) atomically dispersed metal-nitrogen-carbon (M-N-C) catalysts. Here, while many experimental studies have investigated and reported the phenomenological aspects of M-N-C degradation, only a few modeling studies have considered degradation mechanisms at the atomic level. Understanding the mechanisms responsible for activity loss occurring in atomically dispersed M-N-C’s is crucial towards rationally designing active, durable, and less expensive Earth-abundant catalysts. Towards this end, we have surveyed recent literature concerning the modeling of corrosion mechanisms that impact M-N-C catalysts (Fe–N–C, in particular) and offer our own perspectives on the future direction of this field.
The widespread use of fuel cell technology is hampered by the use of expensive and scarce platinum metal in electrodes which is required to facilitate the sluggish oxygen reduction reaction (ORR). In this work, a viable synthetic approach was developed to prepare iron-based sulfur and nitrogen dual doped porous carbon (Fe@SNDC) for use in ORR. Benzimidazole, a commercially available monomer, was used as a precursor for N doped carbon and calcined with potassium thiocyanate at different temperatures to tune the pore size, nitrogen content and different types of nitrogen functionality such as pyridinic, pyrrolic and graphitic. The Fe@SNDC–950 with high surface area, optimum N content of about 5 at% and high amount of pyridinic and graphitic N displayed an onset potential and half-wave potential of 0.98 and 0.83 V vs RHE, respectively, in 0.1 M KOH solution. The catalyst also exhibits similar oxygen reduction reaction performance compared to Pt/C (20 wt%) in acidic media. Furthermore, when compared to commercially available Pt/C (20 wt%), Fe@SNDC–950 showed enhanced durability over 6 h and poison tolerance in case of methanol crossover with the concentration up to 3.0 M in oxygen saturated alkaline electrolyte. Finally, our study demonstrates that the presence of N and S along with Fe-N moieties synergistically served as ORR active sites while the high surface area with accessible pores allowed for efficient mass transfer and interaction of oxygen molecules to the active sites contributing to the ORR activity of the catalyst.
Electron, proton and oxygen-triple-conducting materials are becoming the dominant steam electrode candidate to break the rate limit on the water-splitting reaction that throttles the performance of protonic ceramic electrolysis cells (PCECs). In this study, based on Pr 2 NiO 4+δ Ruddlesden-Popper phase, we manipulate these conductivities by Pr-site Ba substitution to probe the correlation of each conductivity with the kinetics of the elementary reaction steps. It is found that the proton conductivity is vital to sustain an extended active surface area for faster adsorption of reactants and desorption of products. The effect of oxygen conductivity is surprisingly found insignificant in the water-splitting reaction. On the contrary, surface oxygen removal is discovered as the most rate-limiting process. The electronic conductivity is not a direct limiting factor. However, an electron transfer process between the current collector and the electrode junction could introduce extra resistance that is perceptible at a high operating temperature range. The best water-splitting activity is obtained on a proton conductivity/oxygen surface desorption capability well-balanced sample after Ba substitution. As a result, a water-splitting reaction resistance of 0.022 Ωcm 2 , a current density of 1.96 A/cm 2 at 700 °C is achieved on Pr 1.7 Ba 0.3 NiO 4+δ , one of the best performances for PCECs.
Transition metal-nitrogen-carbon (M-N-C) materials have been the focus of scientists’ efforts to address the rising need for earth-abundant materials solutions for energy technology and decarbonization of the economy. They are viewed as one of the most promising candidates to replace platinum group metal (PGM) catalysts in the fuel cell and energy conversion fields, including the application of oxygen reduction reaction, carbon dioxide reduction reaction, and nitrogen reduction reaction. In the effort to improve M-N-C materials properties and achieve atomic dispersity of the transition metal in the carbonaceous matrix, a re-pyrolysis process has been proposed. This secondary heat treatment process of already obtained primary pyrolysis-derived M-N-C materials has been widely reported to substantially improve the electrochemical performance and operational stability of the catalysts. Here, we report a systematic investigation of this process used on samples of templated M-N-C catalysts to obtain state-of-the-art catalysts via in situ heating X-ray photoelectron spectroscopy (XPS), scanning transmission electron microscopy (STEM), energy-dispersive X-ray spectroscopy (EDS), electron energy loss spectroscopy (EELS), X-ray diffraction (XRD), and X-ray computed tomography (CT) characterization methods. It is found that the re-pyrolysis of M-N-C materials could result in the partial amorphization of the carbonaceous substrate. It causes the rearrangement and transformation of multitudinous N moieties, leading to optimization of their morphological display and association with atomically dispersed transition metal dopants. Ultimately, the re-pyrolysis results in an increase in uniformity of the active Fe-Nx sites distribution without the formation of nano-crystalline phases (metallic or carbide) and with overall preservation of the morphology of the carbonaceous framework achieved during the first formative pyrolysis step of the templated synthesis. Finally, these observations provide confirmation that empirically established re-pyrolysis is recommended to be used on all M-N-C materials despite the different synthesis routes to obtain a practical advanced catalytic material.
Anion exchange member (AEM) fuel cells have gained great attention recently mainly owing to the advantages of non-precious metal catalysts application. Despite of the similar oxygen reduction reaction (ORR) kinetics in acid and base, the reaction kinetics of hydrogen oxidation reaction (HOR) is two orders of magnitude slower in alkaline systems than in acid. To understand the slower kinetics of HOR in base, two major interpretations have been proposed, including 1) hydrogen binding energy as a major descriptor for HOR in both acid and base; and 2) bifunctional theory based on the contributions from both hydrogen and hydroxide adsorption for HOR in alkaline electrolyte. Here, we discuss the possible HOR mechanisms in alkaline electrolytes with the corresponding Tafel behavior change. Besides the discussion of traditional Tafel-Volmer and Heyrovsky-Volmer HOR mechanisms, the recently proposed hydroxide adsorption step is discussed to illustrate the HOR mechanism difference in acid and base. We further correlate the hydroxide adsorption step involved mechanism with HOR catalyst design, and summarize its role in HOR and HER activities improvement in alkaline electrolyte over the same catalyst. The representative works of alkaline HOR catalyst development were briefly introduced, and the strategy of strengthening interaction between H2 desorption and H2O recombination was finally proposed for future HOR catalyst design in alkaline environment.
Efficiency of water splitting for hydrogen production is often limited by the sluggish kinetics of multiple electronic transfers required in the heterogeneous oxygen evolution reaction (OER). Catalyst design for reducing the high OER overpotential remains a major scientific challenge. Lattice-strain engineering, a method for tuning the electronic structure and surface geometric configuration of active sites, may greatly affect the interaction between adsorbates and catalytic surfaces for high activity and stability. Here, in this study, we present the synthesis of biphasic oxides of YPrSrRuMnO x , which consists of distinct phases of Y 2 Ru 2 O 7 pyrochlore and (Pr 0.7 Sr 0.3 )MnO 3 perovskite, and the development of a suitable analytical approach to study the strain–catalytic property relationship. Linear sweep voltammetry results reveal that the biphasic oxide exhibits approximately 3.1 times greater mass activity and 2.4 times larger turnover frequency (TOF) than single-phase Y 2 Ru 2 O 7 in the 0.1 M HClO 4 electrolyte. The biphasic catalyst is also about 3 times more stable than the single-phase oxide under acidic conditions. X-ray photoelectron spectroscopy, nitrogen isotherm, and electrochemical surface area analyses indicate that the oxidation state, specific surface area, and electrochemical surface area do not cause enough difference in the observed enhancement of OER performance. We examined the effects of microstrain on electrocatalysis, originating from lattice mismatch between different phases, using three different structural models. Specifically, we compared the Williamson–Hall method, standard stress–strain analysis, and Rietveld refinement in analyzing the structure–property relationship. Strain mapping using geometric phase analysis (GPA) further revealed significant microstrain and lattice dislocations localized near phase boundaries in the biphasic oxide, in contrast to the uniform strain in single-phase materials. The results reveal that the increased microstrain correlates well with the improved OER performance, as the biphasic oxide catalyst exhibits 2–3 times greater microstrain than Y 2 Ru 2 O 7 pyrochlore.
Upcycling plastic waste into value-added products is a promising strategy for both economic and environmental sustainability. However, achieving control over structure–property correlations during the upcycling process remains challenging. Here, in this study, we investigate the modulation of active site formation during pyrolytic conversion of plastics to carbon by composition-controlled molten salts. Using melamine formaldehyde (MF) foams as a precursor, we demonstrate that their pyrolysis in eutectic chloride molten salts with Fe 2+ , Na + , and K + ions directs the carbonization process toward the formation of mesoporous functional carbon enriched with atomically dispersed Fe–N–C sites, which are well-known for their catalytic activity in oxygen reduction reaction (ORR). Compared to pyrolysis in the FeCl 2 -only salt, the incorporation of alkali metal ions (Na + , K + ) in the eutectic mixture facilitates nitrogen retention in the carbon matrix and modulates iron speciation. This synergistic environment promotes a higher density and more uniform dispersion of Fe–N–C moieties within the carbon matrix. Consequently, the resulting catalyst exhibits a high surface area, hierarchical porosity, and improved electrochemical properties. When tested as an ORR catalyst, the Fe–N–C-enriched catalyst delivers a high half-wave potential (E 1/2 = 0.875 V vs RHE) with nearly exclusive 4e – pathway. These properties are comparable to those of commercial Pt/C catalysts, along with improved stability.