Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Densification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2001

Modeled Seasonal Variations of Firn Density Induced by Steady State Surface Air Temperature Cycle

Seasonal variations of firn density in ice-sheet firn layers have been attributed to variations in deposition processes or other processes within the upper firn. A recent high-resolution (mm scale) density profile, measured along a 181 m core from Antarctica, showed small-scale density variations with a clear seasonal cycle that apparently was not-related to seasonal variations in deposition or known near-surface processes (Gerland and others 1999). A recent model of surface elevation changes (Zwally and Li, submitted) produced a seasonal variation in firn densification, and explained the seasonal surface elevation changes observed by satellite radar altimeters. In this study, we apply our 1-D time-dependent numerical model of firn densification that includes a temperature-dependent formulation of firn densification based on laboratory measurements of grain growth. The model is driven by a steady-state seasonal surface temperature and a constant accumulation rate appropriate for the measured Antarctic ice core. The modeled seasonal variations in firn density show that the layers of snow deposited during spring to mid-summer with the highest temperature history compress to the highest density, and the layers deposited during later summer to autumn with the lowest temperature history compress to the lowest density. The initial amplitude of the seasonal difference of about 0.13 reduces to about 0.09 in five years and asymptotically to 0.92 at depth, which is consistent with the core measurements.

Jun, Li↗
NASA NTRS2007

Improved C/SiC Ceramic Composites Made Using PIP

Improved carbon-fiber-reinforced SiC ceramic-matrix composite (C/SiC CMC) materials, suitable for fabrication of thick-section structural components, are producible by use of a combination of raw materials and processing conditions different from such combinations used in the prior art. In comparison with prior C/SiC CMC materials, these materials have more nearly uniform density, less porosity, and greater strength. The majority of raw-material/processing-condition combinations used in the prior art involve the use of chemical vapor infiltration (CVI) for densifying the matrix. In contrast, in synthesizing a material of the present type, one uses a combination of infiltration with, and pyrolysis of, a preceramic polymer [polymer infiltration followed by pyrolysis (PIP)]. PIP processing is performed in repeated, tailored cycles of infiltration followed by pyrolysis. Densification by PIP processing takes less time and costs less than does densification by CVI. When one of these improved materials was tested by exposure to a high-temperature, inert-gas environment that caused prior C/SiC CMCs to lose strength, this material did not lose strength. (Information on the temperature and exposure time was not available at the time of writing this article.) A material of the present improved type consists, more specifically, of (1) carbon fibers coated with an engineered fiber/matrix interface material and (2) a ceramic matrix, containing SiC, derived from a pre-ceramic polymer with ceramic powder additions. The enhancements of properties of these materials relative to those of prior C/SiC CMC materials are attributable largely to engineering of the fiber/ matrix interfacial material and the densification process. The synthesis of a material of this type includes processing at an elevated temperature to a low level of open porosity. The approach followed in this processing allows one to fabricate not only simple plates but also more complexly shaped parts. The carbon fiber reinforcement in a material of this type can be in any of several alternative forms, including tow, fabric, or complex preforms containing fibers oriented in multiple directions.

Easler, Timothy↗
DOE OSTI2014

A Validation Study of Pin Heat Transfer for UO2 Fuel Based on the IFA-432 Experiments

The IFA-432 (Integrated Fuel Assessment) experiments from the International Fuel Performance Experiments (IFPE) database were designed to study the effects of gap size, fuel density, and fuel densification on fuel centerline temperature in light-water-reactor fuel. An evaluation of nuclear fuel pin heat transfer in the FRAPCON-3.4 and Exnihilo codes for uranium dioxide (UO$_2$) fuel systems was performed, with a focus on the densification stage (2.2 \unitfrac{GWd}{MT(UO$_{2}$)}). In addition, sensitivity studies were performed to evaluate the effect of the radial power shape and approximations to the geometry to account for the thermocouple hole. The analysis demonstrated excellent agreement for rods 1, 2, 3, and 5 (varying gap thicknesses and density with traditional fuel), demonstrating the accuracy of the codes and their underlying material models for traditional fuel. For rod 6, which contained unstable fuel that densified an order of magnitude more than traditional, stable fuel, the magnitude of densification was over-predicted and the temperatures were outside of the experimental uncertainty. The radial power shape within the fuel was shown to significantly impact the predicted centerline temperatures, whereas modeling the fuel at the thermocouple location as either annular or solid was relatively negligible. This has provided an initial benchmarking of the pin heat transfer capability of Exnihilo for UO$_2$ fuel with respect to a well-validated nuclear fuel performance code.

Phillippe, Aaron M↗
DOE OSTI2024

Turning Normal to Abnormal: Reversing CO 2 /C2–Hydrocarbon Selectivity in HKUST–1

Metal–organic frameworks (MOFs) can efficiently purify hydrocarbons from CO 2 , but their rapid saturation, driven by preferential hydrocarbon adsorption, requires energy-intensive adsorption–desorption processes. To address these challenges, an innovative approach is developed, enabling control over MOF flexibility through densification and defect engineering, resulting in an intriguing inverse CO 2 /C2 hydrocarbon selectivity. Here, in this study, the densification process induces the shearing of the crystal lattice and contraction of pores in a defective CuBTC MOF. These changes have led to a remarkable transformation in selectivity, where the originally hydrocarbon-selective CuBTC MOF becomes CO 2 -selective. The selectivity values for densified CuBTC are significantly reversed when compared to its powder form, with notable improvements observed in CO 2 /C 2 H 6 (4416 vs 0.61), CO 2 /C 2 H 4 (15 vs 0.28), and CO 2 /C 2 H 2 (4 vs 0.2). The densified material shows impressive separation, regeneration, and recyclability during dynamic breakthrough experiments with complex quinary gas mixtures. Simulation studies indicate faster CO 2 passage through the tetragonal structure of densified CuBTC compared to C 2 H 2 . Experimental kinetic diffusion studies confirm accelerated CO 2 diffusion over hydrocarbons in the densified MOF, attributed to its small pore window and minimal interparticle voids. This research introduces a promising strategy for refining existing and future MOF materials, enhancing their separation performance.

36 MATERIALS SCIENCE↗
NASA NTRS2015

ASME Section VIII Recertification of a 33,000 Gallon Vacuum-jacketed LH2 Storage Vessel for Densified Hydrogen Testing at NASA Kennedy Space Center

The Ground Operations Demonstration Unit for Liquid Hydrogen (GODU-LH2) has been developed at NASA Kennedy Space Center in Florida. GODU-LH2 has three main objectives: zero-loss storage and transfer, liquefaction, and densification of liquid hydrogen. A cryogenic refrigerator has been integrated into an existing, previously certified, 33,000 gallon vacuum-jacketed storage vessel built by Minnesota Valley Engineering in 1991 for the Titan program. The dewar has an inner diameter of 9.5 and a length of 71.5; original design temperature and pressure ranges are -423 F to 100 F and 0 to 95 psig respectively. During densification operations the liquid temperature will be decreased below the normal boiling point by the refrigerator, and consequently the pressure inside the inner vessel will be sub-atmospheric. These new operational conditions rendered the original certification invalid, so an effort was undertaken to recertify the tank to the new pressure and temperature requirements (-12.7 to 95 psig and -433 F to 100 F respectively) per ASME Boiler and Pressure Vessel Code, Section VIII, Division 1. This paper will discuss the unique design, analysis and implementation issues encountered during the vessel recertification process.

Liquefaction↗
NASA NTRS2017

Large Scale Production of Densified Hydrogen to the Triple Point and Below

Recent demonstration of advanced liquid hydrogen storage techniques using Integrated Refrigeration and Storage technology at NASA Kennedy Space Center led to the production of large quantities of densified liquid and slush hydrogen in a 125,000 L tank. Production of densified hydrogen was performed at three different liquid levels and LH2 temperatures were measured by twenty silicon diode temperature sensors. Overall densification performance of the system is explored, and solid mass fractions are calculated. Experimental data reveal hydrogen temperatures dropped well below the triple point during testing, and were continuing to trend downward prior to system shutdown. Sub-triple point temperatures were seen to evolve in a time dependent manner along the length of the horizontal, cylindrical vessel. The phenomenon, observed at two fill levels, is detailed herein. The implications of using IRAS for energy storage, propellant densification, and future cryofuel systems are discussed.

IRAS↗
NASA NTRS2017

Large Scale Production of Densified Hydrogen to the Triple Point and Below

Recent demonstration of advanced liquid hydrogen storage techniques using Integrated Refrigeration and Storage technology at NASA Kennedy Space Center led to the production of large quantities of densified liquid and slush hydrogen in a 125,000 L tank. Production of densified hydrogen was performed at three different liquid levels and LH2 temperatures were measured by twenty silicon diode temperature sensors. Overall densification performance of the system is explored, and solid mass fractions are calculated. Experimental data reveal hydrogen temperatures dropped well below the triple point during testing, and were continuing to trend downward prior to system shutdown. Sub-triple point temperatures were seen to evolve in a time dependent manner along the length of the horizontal, cylindrical vessel. The phenomenon, observed at two fill levels, is detailed herein. The implications of using IRAS for energy storage, propellant densification, and future cryofuel systems are discussed.

Hydrogen↗
DOE OSTI2018

Highly Densified Cu Wirings Fabricated from Air-Stable Cu Complex Ink with High Conductivity, Enhanced Oxidation Resistance, and Flexibility

The microstructure of printed Cu wirings fabricated from air-stable Cu complex inks is greatly modified by low-temperature curing followed by intense pulsed light densification enhancement treatment. The resulting almost full densification of printed Cu wirings enables them to possess a high electrical conductivity of 50% bulk Cu. The dense structure also largely prevents the permeation of oxygen and water into the inner side of the Cu wirings, thereby improving their oxidation resistance and maintaining a stable resistance (R/R0 < 1.5) even after 1000 h aging at 85 °C-85% RH. In addition, the dense and robust structure can improve the resistance to crack generation and propagation in Cu wirings during the bending, so as to improve their flexibility. The relative resistance of Cu wirings can be kept below 1.2 after 1000 bending cycles. All the results indicate that these highly densified Cu wirings fabricated from air-stable Cu complex inks can be used to replace the noble metallic Au and Ag wirings for practical application in flexible electronics.

Li, Wanli↗
DOE OSTI2012

Factors affecting the microstructural stability and durability of thermal barrier coatings fabricated by air plasma spraying

The high-temperature behavior of high-purity, low-density (HP-LD) air plasma sprayed (APS) thermal barrier coatings (TBCs) with NiCoCrAlY bond coats deposited by argon-shrouded plasma spraying is described. The high purity yttria-stabilized zirconia resulted in top coats which are highly resistant to sintering and transformation from the metastable tetragonal phase to the equilibrium mixture of monoclinic and cubic phases. The thermal conductivity of the as-processed TBC is low but increases during high temperature exposure even before densification occurs. The porous topcoat microstructure also resulted in good spallation resistance during thermal cycling. The actual failure mechanisms of the APS coatings were found to depend on topcoat thickness, topcoat density, and the thermal cycle frequency. The failure mechanisms are described and the durability of the HP-LD coatings is compared with that of state-of-the-art electron beam physical vapor deposition TBCs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Uncovering the Size-dependent Thermal Solid Transformation of Akaganéite

Investigating the structural evolution and phase transformation of iron oxides is crucial for gaining a deeper understanding of geological changes on diverse planets and preparing oxide materials suitable for industrial applications. In this study, we employed in-situ heating techniques in conjunction with transmission electron microscopy (TEM) observations and ex-situ characterization to thoroughly analyze the thermal solid-phase transformation of akaganéite one-dimensional (1D) nanostructures with varying diameters. Our findings offer compelling evidence for a size-dependent morphology evolution in akaganéite 1D nanostructures, which can be attributed to the transformation from akaganéite to maghemite (?-Fe2O3) and subsequent crystal growth. Specifically, we observed that akaganéite nanorods with a diameter of around 50 nm transformed into hollow polycrystalline maghemite nanorods, which demonstrated remarkable stability without arresting crystal growth under continuous heating. In contrast, smaller akaganéite nanoneedles or nanowires with a diameter ranging from 20 to 8 nm displayed a propensity for forming single-crystal nanoneedles or nanowires through phase transformation and densification. By manipulating the size of the precursors, we have developed a straightforward method for the synthesis of single-crystal and polycrystalline maghemite nanowires through solid-phase transformation. These significant findings provide new insights into the size-dependent structural evolution and phase transformation of iron oxides at the nanoscale.

Wang, Xiang↗
DOE OSTI2023

A Level Set Model for Structured Mesh Representation of Fibrous Preforms used in Composites Manufacturing

Here, a model for implicit representation of fibrous and woven preforms used for composites manufacturing is described. The method is based on a level set function defined on a structured mesh to implicitly capture the complex fiber and weave geometries. Since most software packages used to model woven preforms are based on unstructured mesh, a numerical model for transforming a discretized surface to a structured mesh representation and vice-a-versa is presented. Specific emphasis is on scalable computation of a level set function for large and complex 3D woven structures from a triangulated surface of the smallest unit (yarn). The model is applied to capture a periodic 3D layered 5-harness satin (5HS) weave geometry on a structured mesh. Geometric transformations needed to efficiently compute the level set function for the 3D structure on a high resolution mesh are described. Effects of mesh resolution on the geometric features such as number of resolved fibers, effective fiber size, and the surface area to volume ratio of the iso-surface are analyzed. Using the distance property of the level set function, an approach to evaluate the structure function resulting from transient evolving topology representing densification due to matrix phase depositions is also presented. The approach captures transition of the geometric characteristic from fiber governed at early stages of densification to yarn governed at the terminal stage.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Processing of crack-free high density polycrystalline LiTaO3 ceramics

Our work achieved high density (99.9%) polycrystalline LiTaO 3 . The keys to the high density without cracking were the use of LiF-assisted densification to maintain fine grain size as well as the presence of secondary lithium aluminate phases as grain growth inhibitors. The average grain size of the hot pressed polycrystalline LiTaO 3 is less than 5 μm, limiting residual stresses caused by the anisotropic thermal expansion. Dilatometry results clearly indicate liquid phase sintering via the added LiF sintering aid. Efficient liquid phase sintering allows densification during low temperature hot pressing. Electron microscopy confirmed the high-density microstructure. Furthermore, Rietveld analysis of neutron diffraction data revealed the presence of LiAlO 2 and LiAl 5 O 8 minority phases and negligible substitutional defect incorporation in LiTaO 3 .

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Limit to Accelerated Free-Sintering: Nano-Phase Separation Interferes With Organic Debinding

Nano-phase separating Ni–12 at. pct Ag powders are processed via high-energy ball milling and brought into a supersaturated state with a reduction of the grain size to the nanocrystalline scale, a combination that is designed to encourage rapid densification by phase separation upon heating. This unstable powder is then characterized by dilatometry, in-situ x-ray diffraction, thermogravimetry and microstructure analysis for sintering cycles up to 940 °C. However, these powder compacts exhibit excessive pore evolution and significant macroscopic swelling caused by removal of the organic process additives. This competition of organic removal with densification is known in nanocrystalline metals, but the present study adds an additional dimension of phase separation, which shifts the dominant swelling mechanism as the formation of the second phase traps the volatilizing organics and hinders the debinding process. The creep swelling and overall loss in relative density is then dominated by the creep deformation of the second Ag phase. The interference between organic removal and low-temperature onset of consolidation represents a new challenge to efforts aimed at rapid free sintering and should guide the design of rapidly sintering alloys; specifically, the present work emphasizes the need to select alloys that have their sintering-accelerating phase separation temperature above the range where gases are evolved.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Neutron Diffraction and Neutron Radiography Investigation into Powder Sintering of Ti/Al and TiH{sub 2}/Al Compacts

Sintering behaviors of two types of powder compact, i.e., Ti/Al and TiH{sub 2}/Al, under vacuum were studied using in situ neutron diffraction, in situ thermal dilatometric measurement, and ex situ neutron radiography. Their densification, microstructure, hydrogen concentration, and phase transformation features were compared. The results indicate that the predominant phase identified in the samples sintered from both compacts is γ-TiAl phase with minor Ti{sub 3}Al phase. Dehydrogenation of TiH{sub 2} plays a decisive role in the sintering behavior and the resultant microstructure. In comparison with the Ti/Al compact, dehydrogenation occurring in the TiH{sub 2}/Al compact leads to a higher level of densification and faster sintering kinetics.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Influence of Particle Size on Apparent Diffusivity During Spark Plasma Sintering of Crystalline Powders

Abstract:: A theoretical framework is presented to determine an apparent diffusivity D during powder sintering and further elucidate the underlying interrelation between D and shrinkage behaviors of powders. Furthermore, to eliminate the influence of crystalline defects that are typically present in raw powders, complete crystallization of metallic glass powders is performed to allow the investigation of the influence of particle size solely on powder densification. Furthermore, to validate the framework developed, Ti{sub 40.6}Zr{sub 9.4}Cu{sub 37.5}Ni{sub 9.4}Sn{sub 3.1} crystalline alloy powders constituting particles with different sizes are examined to establish a correlation between D and the sintering behaviors of the powders. The findings show that the value of the apparent diffusivity D increases with the increasing particle size, which accelerates powder densification during spark plasma sintering. Furthermore, the results quantitatively support the argument that particle size can affect atomic diffusion during powder sintering.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Shear Assisted Processing and Extrusion (ShAPE™) of AZ91E Flake: A Study of Tooling Features and Processing Effects

Charges of melt-spun AZ91E flake were indirectly extruded into tubes using Shear Assisted Processing and Extrusion (ShAPE™). The effect of instrument parameters and tool features on densification and microstructural evolution was studied. At a constant extrusion ratio, the tool rotational velocity varied from 75 to 300 rpm and was demonstrated to reduce the forge force by a factor of four. Modification of the extrusion die face with successively more aggressive scrolled features was found to enhance material flow into the extrusion orifice which led to a 30% reduction in spindle torque. Microstructure, texture and hardness are reported for the range of rpm and scroll geometries investigated. It was observed that the ShAPE™ process is able to retain the average grain size of the as-spun flake (2.5-4 μm) while simultaneously imparting strong textural alignment in the resultant tube.

36 MATERIALS SCIENCE↗
DOE OSTI2015

SANS Investigations of CO 2 Adsorption in Microporous Carbon

The high pressure adsorption behavior of CO 2 at T = 296 K in microporous carbon was investigated by small-angle neutron scattering (SANS) technique. A strong densification of CO 2 in micropores accompanied by non-monotonic adsorption-induced pore deformation was observed. The density of confined CO 2 increases rapidly with pressure and reaches the liquid –like density at 20 bar, which corresponds to the relative pressure of P/Psat ~0.3. At P > 20 bar density of confined CO 2 increases slowly approaching a plateau at higher pressure. The size of micropores first increases with pressure, reaches a maximum at 20 bar, and then decreases with pressure. A complementary SANS experiment conducted on the same microporous carbon saturated with neutron-transparent and non-adsorbing inert gas argon shows no deformation of micropores at pressures up to ~200 bars. This result demonstrates that the observed deformation of micropores in CO 2 is an adsorption-induced phenomenon, caused by the solvation pressure - induced strain and strong densification of confined CO 2 .

54 ENVIRONMENTAL SCIENCES↗