Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Correlation analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Development and evaluation of a list mode neutron coincidence collar for spatial response measurements of fresh fuel assemblies

A traditional safeguards neutron coincidence counting system, the Neutron Coincidence Collar, has been modified to incorporate individual preamplifiers on each of its 18 3He tubes in active interrogation mode. When used with list mode data acquisition (LMDA) and analysis, a signal from each 3He tube can be recorded and analyzed to allow a spatial response measurement to be performed on an item based on count rate and 3He tube location within the system. The ultimate goal of this project is to demonstrate the capabilities of a list mode response matrix for the nondestructive assay of fresh nuclear fuel assemblies. To enable partial defect detection of fuel pin locations and absences within an assembly, the project aims to extend well-established correlated neutron analysis techniques on a preexisting Neutron Coincidence Collar by extracting a greater number of useful signatures from the system than are currently generated. LMDA, combined with the addition of multiple preamplifiers, facilitates this capability by increasing the number of simultaneous signals that can be measured; this allows an in-depth analysis of neutron coincidence events to determine a fissioning item’s location based on the measured doubles count rate in various channel logic coincidence combinations. All of this can be done from a single measurement pulse train in offline analysis, which is the major benefit provided by LMDA. Through various stages of development and testing, a Mirion Technologies model JCC-71 Neutron Coincidence Collar has been successfully retrofit with modern electronics designed in-house at Oak Ridge National Laboratory, matching preexisting JAB-01 electronics performance, while maintaining the original system footprint. This paper presents these various stages of development and experimental evaluation of the proof of concept system.

Moore, Angela S.↗
DOE OSTI2024

How do mirror charge radii constrain density dependence of the symmetry energy?

It has recently been suggested that differences in the charge radii of mirror nuclei (Δ$R^{mirr}_{ch}$) are strongly correlated with the neutron-skin thickness ($R_{skin}$) of neutron-rich nuclei and with the slope of the symmetry energy ($L$). To test this assumption, we present ab initio calculations of $R_{skin}$ in 48 Ca and 208 Pb, Δ$R^{mirr}_{ch}$ in 36 Ca$-$ 36 S, 38 Ca$-$ 38 Ar, 41 Sc$-$ 41 Ca, 48 Ni$-$ 48 Ca, 52 Ni$-$ 52 Cr, and 54 Ni$-$ 54 Fe mirror pairs, and $L$. Employing the recently developed 34 chiral interaction samples, identified by the history matching approach, we conduct rigorous statistical analysis of correlations among Δ$R^{mirr}_{ch}$, $R_{skin}$ and $L$, accounting for quantified uncertainties from low-energy constants of chiral interaction, chiral effective field theory truncation and many-body method approximation. The ab initio results reveal an appreciable Δ$R^{mirr}_{ch}$ $-$ $L$ correlation in $fp$-shell mirror pairs. However, contrary to previous studies, the present calculation finds that the studied $sd$-shell mirror pairs do not exhibit any Δ$R^{mirr}_{ch}$ $-$ $L$ correlation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2021

Celestial IR divergences and the effective action of supertranslation modes

Infrared divergences in perturbative gravitational scattering amplitudes have been recently argued to be governed by the two-point function of the supertranslation Goldstone mode on the celestial sphere. We show that the form of this celestial two-point function simply derives from an effective action that also controls infrared divergences in the symplectic structure of General Relativity with asymptotically flat boundary conditions. This effective action finds its natural place in a path integral formulation of a celestial conformal field theory, as we illustrate by re-deriving the infrared soft factors in terms of celestial correlators. Our analysis relies on a well-posed action principle close to spatial infinity introduced by Compère and Dehouck.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2023

Pressure-based process monitoring of direct-ink write material extrusion additive manufacturing

As additive manufacturing (AM) has become a reliable method for creating complex and unique hardware rapidly, the quality assurance of printed parts remains a priority. In situ process monitoring offers an approach for performing quality control while simultaneously minimizing post-production inspection. For extrusion printing processes, direct linkages between extrusion pressure fluctuations and print defects can be established by integrating pressure sensors onto the print head. In this work, the sensitivity of process monitoring is tested using engineered spherical defects. Pressure and force sensors located near an ink reservoir and just before the nozzle are shown to assist in identification of air bubbles, changes in height between the print head and build surface, clogs, and particle aggregates with a detection threshold of 60–70% of the nozzle diameter. Visual evidence of printed bead distortion is quantified using optical image analysis and correlated to pressure measurements. Importantly, this methodology provides an ability to monitor the quality of AM parts produced by extrusion printing methods and can be accomplished using commonly available pressure-sensing equipment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Thermodynamic modeling of double azeotropy systems

Azeotropes are boiling liquid mixtures which have identical vapor and liquid compositions. Known as polyazeotropy, azeotropic mixtures may exhibit more than one azeotrope at a given temperature or pressure. While the thermodynamic condition for azeotrope formation in vapor-liquid equilibrium is well established, thermodynamic modeling of mixtures exhibiting polyazeotropy remains challenging and prior modeling studies often failed to satisfactorily correlate the polyazeotropic behavior of associating systems. Based on the association NRTL model, this study presents successful correlation and analysis of double azeotrope formation for three diverse systems: strongly associating methanol + diethylamine binary, weakly associating ammonia + pentafluoroethane binary, and non-associating benzene + hexafluorobenzene binary systems. Furthermore, these systems exhibit polyazeotropic behavior as the temperature increases and approaches their Bancroft points.

42 ENGINEERING↗
DOE OSTI2026

Topology-driven compressive behavior of Inconel 718 lattice structures with Z-strut reinforcement fabricated by laser powder bed fusion

This study investigates the compressive deformation behavior and mechanical performance of Inconel 718 lattice structures fabricated by laser powder bed fusion (LPBF). Four unit-cell topologies—BCC, FCC, BCCZ, and FCCZ—were designed with a unit-cell size of 3 mm and fabricated under identical process conditions to isolate the effect of topology. Measured relative densities ranged from 14.65% to 17.72%. Compressive testing showed that Z-strut-reinforced topologies (BCCZ: 54.6 MPa; FCCZ: 80.2 MPa) exhibited higher strength than their unreinforced counterparts, which may be associated with mixed-mode deformation behavior enabled by the vertically aligned Z-struts. Finite element simulations and Digital Image Correlation (DIC) analysis support the observation of a transition from node-dominated deformation in BCC/FCC to mixed-mode deformation in BCCZ/FCCZ. These findings suggest that unit-cell topology is a key design variable for tailoring deformation mechanisms in LPBF lattice structures.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of neutron irradiation on Al-6061 alloy produced via ultrasonic additive manufacturing

Samples of aluminum alloy 6061 produced via ultrasonic additive manufacturing (UAM) were irradiated in the High Flux Isotope Reactor (HFIR) up to 17.3 dpa at ~70°C while in contact with water using perforated rabbit capsules. The irradiation campaign included as-received (AR) material, specimens subjected to various post-weld heat treatments (PWHTs, including hot isostatic pressing [HIP]), and reference (wrought) alloy samples. Mechanical tensile tests, accompanied by digital image correlation (DIC) analysis, fractography, and metallography, were performed as a part of the post-irradiation evaluation. The X- and Y-specimens (i.e., oriented in the sonotrode moving and vibration directions, respectively) showed pronounced radiation hardening and ductility decrease. Specific serration flow behavior and propagation of deformation bands were observed under various material conditions up to 3.5 dpa but disappeared at 17.3 dpa. In all cases, the fracture mechanism of X- and Y-specimens was ductile; ductile dimples dominated the fracture surface. Irradiated X- and Y-specimens showed good performance, regardless of material conditions (AR or PWHT). The performance of Z-specimens oriented in the build direction was strongly dependent on the PWHT. The AR and aged specimens showed fracture stress decrease with dose, and they experienced fracture under irradiation after 3.5 dpa; specimen cross section analysis revealed specific interface degradation that was likely related to corrosion. Recrystallization significantly improved in-reactor performance. Finally, HIP suppressed interface degradation due to recrystallization and pore removal, which led to good in-reactor performance for Z-specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A Denoising Autoencoder for Improved Kikuchi Pattern Quality and Indexing in Electron Backscatter Diffraction

The rapid collection and indexing of electron diffraction patterns as produced via electron backscatter diffraction (EBSD) has enabled crystallographic orientation and structural determination, as well as additional property-determining strain and dislocation density information with increasing speed, resolution, and efficiency. Pattern indexing quality is reliant on the noise of the collected electron diffraction patterns, which is often convoluted by sample preparation and data collection parameters. EBSD acquisition is sensitive to many factors and thus can result in low confidence index (CI), poor image quality (IQ), and improper minimization of fit, which can result in noisy datasets and misrepresent the microstructure. In an attempt to enable both higher speed EBSD data collection and enable greater orientation fit accuracy with noisy datasets, an image denoising autoencoder was implemented to improve pattern quality. Here, we show that EBSD data processed through the autoencoder results in a higher CI, IQ, and a more accurate degree of fit. In addition, using denoised datasets in HR-EBSD cross correlative strain analysis can result in reduced phantom strain from erroneous calculations due to the increased indexing accuracy and improved correspondence between collected and simulated patterns.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mechanisms of proton transport in aqueous acid solutions

The fundamental understanding of proton transport, specifically the Grotthuss-like mechanism, is critical for many technological applications. The present study presents a comprehensive analysis of proton transport in aqueous solutions of sulfuric and phosphoric acids using quasielastic neutron and light scattering, broadband dielectric spectroscopy, rheology, pulsed-field gradient-NMR measurements, and ab initio molecular dynamic simulations. Results show that in all systems, proton transport occurs through short “jumps” of ~0.5 Å that are faster than structural relaxation. However, proton hopping appears to be coupled to structural relaxation in aqueous solutions of sulfuric acid, while these processes are decoupled in phosphoric acid. Neutron scattering indicates that all protons have the same fast mobility in phosphoric acid systems, while at least one proton per sulfuric molecule remains slower than other protons. Analysis reveals correlated proton jumps, but these correlations suppress conductivity, suggesting that expected Grotthuss-like enhancement of conductivity is unlikely in bulk liquids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

High Throughput Mapping of Single Molecules’ Redox Potentials on Electrode

By synchronizing electrochemical potential scanning with a single-molecule localization super-resolution fluorescence microscope, kinetic fluorescence changes of hundreds of single molecular redox events were tracked simultaneously with high throughput, and subsequent cross-correlation function analysis mapped single molecules’ redox potentials (times) out on the imaging area from site to site in unprecedented detail by extracting electrochemically induced fluorescence change from apparently random fluorescence on/off blinking. This work paves the way toward mapping redox states at single-molecule levels in high throughput in chemical and biological systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Lightning Interferometry Uncertainty, Beam Steering Interferometry, and Evidence of Lightning Being Ignited by a Cosmic Ray Shower

Abstract We present an uncertainty analysis on correlation‐based time delay estimate, the basis for broadband lightning interferometry. A normal interferometry would yield much higher uncertainties than the theoretically predicted lower bound due to finite correlation window lengths. However, if the signals are aligned in time, the uncertainties approach the lower bound and can be used to indicate the interferometric uncertainties. Based on this, we introduce a beam steering interferometry technique. It first estimates a direction centroid for the lightning sources with a normal interferometry and computes the time delays among the signals. It then shifts the raw data with the time delays to align the signals roughly in time and reprocess the aligned signals. It finally pushes the reprocessed results to their correct positions, based on the time delays estimated in the first step. We apply this technique on a fast positive breakdown (FPB) process that started a normal intracloud lightning. The FPB process is shown to have a much more complex structure and development than a normal interferometry would provide. More importantly, from both interferometric and polarization analyses, the FPB appears to be ignited by a cosmic ray shower (CRS). We estimate the radio frequency strength and frequency content related to a presumed CRS in a thunderstorm electric field and find that they are in agreement with the observations. We examine the electric field effect of the CRS front and find that it could raise the field above the threshold for positive breakdown and is capable of igniting the FPB (and the lightning).

Shao, Xuan‐Min↗
DOE OSTI2024

Analysis of static Wilson line correlators from lattice QCD at finite temperature with T -matrix approach

The thermodynamic T-matrix approach is used to study Wilson line correlators (WLCs) for a static quark-antiquark pair in the quark-gluon plasma (QGP). Selfconsistent results that incorporate constraints from the QGP equation of state can approximately reproduce WLCs computed in 2+1-flavor lattice-QCD (lQCD), provided the input potential exhibits less screening than in previous studies. Utilizing the updated potential to calculate pertinent heavylight T-matrices we evaluate thermal relaxation rates of heavy quarks in the QGP. We find a more pronounced temperature dependence for low-momentum quarks than in our previous results (with larger screening), which turns into a weaker temperature dependence of the (temperature-scaled) spatial diffusion coefficient, in fair agreement with the most recent lQCD data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

In situ spin coater for multimodal grazing incidence x-ray scattering studies

We present herein a custom-made, in situ, multimodal spin coater system with an integrated heating stage that can be programmed with spinning and heating recipes and that is coupled with synchrotron-based, grazing-incidence wide- and small-angle x-ray scattering. The spin coating system features an adaptable experimental chamber, with the ability to house multiple ancillary probes such as photoluminescence and visible optical cameras, to allow for true multimodal characterization and correlated data analysis. This system enables monitoring of structural evolutions such as perovskite crystallization and polymer self-assembly across a broad length scale (2 Å–150 nm) with millisecond temporal resolution throughout a complete thin film fabrication process. The use of this spin coating system allows scientists to gain a deeper understanding of temporal processes of a material system, to develop ideal conditions for thin film manufacturing.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Isoplethal study of phase formation and morphology in uranium-304L steel via scanning electron microscopy

Understanding the formation of uranium alloys with steel is important to advance nuclear technologies involving U metal fuels and machining U metal, and for nuclear forensics applications. No known phase diagram for the quaternary U-(M = Fe, Ni, Cr) system exists. For this work, we synthesize samples of U-304 L steel (nominal composition 70.1:18.3:10.4 at% Fe:Cr:Ni) across the U composition range 4.45—63.35 at%U by arc melting under inert conditions. Using the binary UFe phase diagram as a reference, we identify four U-steel alloy phases. We find the known U-Fe analogue phases UM 2 and U 6 M, and two low-U composition phases with nominal compositions UM 10 and U 2 M 7 . We apply a correlation length analysis to backscatter scanning electron microscopy images of sectioned and polished cross sections to quantify the domain formation length scale. We demonstrate that these depend heavily on the initial composition and range from 30 nm to 1.5 µm. This result, in particular, could be applicable to theoretical predictions of transport properties. Furthering our understanding of U alloy phase formation with important structural elements such as steel primaries is foundational in developing future nuclear technology.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Decomposition of multi-particle azimuthal correlations in Q-cumulant analysis*

Abstract The method of Q -cumulants is a powerful tool for studying the fine details of azimuthal anisotropies in high energy nuclear collisions. This paper presents a new method, based on mathematical induction, to evaluate the analytical form of high-order Q -cumulants. The capability of this method is demonstrated via a toy model that uses the elliptic power distribution to simulate the anisotropic emission of particles, quantified in terms of Fourier flow harmonics . The method can help in studying the large amount of event statistics that can be collected in the future and allow measurements of the very high central moments of the distribution. This can, in turn, facilitate progress in understanding the initial geometry, the input to the hydrodynamic calculations of medium expansion in high energy nuclear collisions, and the constraints on it.

Physics↗
DOE OSTI2023

Metal-insulator transition and magnetism of SU(3) fermions in the square lattice

We study the SU(3) symmetric Fermi-Hubbard model (FHM) in the square lattice at 1/3-filling using numerically exact determinant quantum Monte Carlo and numerical linked-cluster expansion techniques. We present the different regimes of the model in the T–U plane, which are characterized by local and short-range correlations, and capture signatures of the metal-insulator transition and magnetic crossovers. These signatures are detected as the temperature scales characterizing the rise of the compressibility, and an interaction-dependent change in the sign of the diagonal spin-spin correlation function. The analysis of the compressibility estimates the location of the metal-insulator quantum critical point at U c /t ~ 6, and provides a temperature scale for observing Mott physics at finite T. Furthermore, from the analysis of the spin-spin correlation function we observe that for U/t ≳ 6 and T ~ J = 4⁢t 2 /U there is a development of a short-range two-sublattice (2SL) antiferromagnetic structure, as well as an emerging three-sublattice (3SL) antiferromagnetic structure as the temperature is lowered below T/J ≲ 0.57. This crossover from 2SL to 3SL magnetic ordering agrees with Heisenberg limit predictions, and has observable effects on the density of on-site pairs. Finally, we describe how the features of the regimes in the T–U plane can be explored with alkaline-earth-like atoms in optical lattices with currently achieved experimental techniques and temperatures. Furthermore, the results discussed in this paper provide a starting point for the exploration of the SU(3) FHM upon doping.

74 ATOMIC AND MOLECULAR PHYSICS↗