Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Characteristic Curves”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Performance Analysis of a Hardware Implemented Complex Signal Kurtosis Radio-Frequency Interference Detector

Radio-frequency interference (RFI) is a known problem for passive remote sensing as evidenced in the L-band radiometers SMOS, Aquarius and more recently, SMAP. Various algorithms have been developed and implemented on SMAP to improve science measurements. This was achieved by the use of a digital microwave radiometer. RFI mitigation becomes more challenging for microwave radiometers operating at higher frequencies in shared allocations. At higher frequencies larger bandwidths are also desirable for lower measurement noise further adding to processing challenges. This work focuses on finding improved RFI mitigation techniques that will be effective at additional frequencies and at higher bandwidths. To aid the development and testing of applicable detection and mitigation techniques, a wide-band RFI algorithm testing environment has been developed using the Reconfigurable Open Architecture Computing Hardware System (ROACH) built by the Collaboration for Astronomy Signal Processing and Electronics Research (CASPER) Group. The testing environment also consists of various test equipment used to reproduce typical signals that a radiometer may see including those with and without RFI. The testing environment permits quick evaluations of RFI mitigation algorithms as well as show that they are implementable in hardware. The algorithm implemented is a complex signal kurtosis detector which was modeled and simulated. The complex signal kurtosis detector showed improved performance over the real kurtosis detector under certain conditions. The real kurtosis is implemented on SMAP at 24 MHz bandwidth. The complex signal kurtosis algorithm was then implemented in hardware at 200 MHz bandwidth using the ROACH. In this work, performance of the complex signal kurtosis and the real signal kurtosis are compared. Performance evaluations and comparisons in both simulation as well as experimental hardware implementations were done with the use of receiver operating characteristic (ROC) curves.

radiometers↗
NASA NTRS2018

Percolation Behaviour in the Magnetic Permeability and Electrical Conductivity in Conducting Magnetic - Insulating Non Magnetic Binary Composites

Experimental results of the complex magnetic permeability (µ) and the electrical conductivity (σ) of a granular paramagnetic Gadolinium Gallium Garnet (GGG: 0.3–26 vol%) and Teflon (PTFE) system are presented and discussed in relation to previously published (conductivity) and unpublished (permeability) studies on granular Fe3O4 – talc and Ni – talc wax systems. In these systems plots of the real conductivity (σ'(sub m)) against the volume fraction (φ) lie on characteristic sigmoid curves that when fitted to the Two Exponent Phenomenological Percolation Equation (TEPPE) confirm the existence of “percolation microstructures” with critical volume fractions (φ(sub c)). The plots of the real and imaginary permeability (µ'(sub m)) and (µ"(sub m)) satisfactorily fit to the TEPPE using the φ(sub c) obtained in each case from the “conductivity” measurements. In all three cases the conductivity results gave the exponent t > 2, and the permeability results gave t < 1.

David S McLachlan↗
NASA NTRS2022

The Influence of Land Use and Land Cover Change on Landslide Susceptibility in the Lower Mekong River Basin

The Lower Mekong River Basin in Southeast Asia experiences frequent rainfall-triggered landslides especially during the monsoon season. In this study, the influence of land use and land cover change and other causative factors on landslide susceptibility is evaluated in the Lower Mekong Basin. Frequency ratio analysis is performed to quantify the relationship between LULC change and susceptibility. Detailed landslide inventory maps are used for analysis with yearly LULC maps. The LULC change is used as a contributing variable in a logistic regression-based susceptibility model with other variables including distance to roads, slope, aspect, forest loss, and soil properties. The Receiver Operating Characteristic (ROC) curve and Area Under the Curve are estimated for the model trained by each landslide inventory. The models show good performance, with AUC values ranging from 0.697 to 0.958 and an average AUC equal to 0.820. Both the Frequency Ratio analysis and the Logistic Regression models indicate LULC change from agricultural land to forest has a positive correlation with landslide occurrence. The most significant factors in the models are found to be distance to roads, slope, and aspect. A better understanding of the effects of LULC on landslide susceptibility can be useful for local land and disaster management and for the implementation of LULC as a factor in future susceptibility models. Using datasets that are unique to the Lower Mekong region, this study provides additional insights into the relationship between causative factors and landslide activity to better inform regional and global landslide susceptibility modeling.

River Basin↗
DOE OSTI2024

Laser Based Ultrasound for Verification of Circuit Card Assemblies

This IR is a follow-up conference Paper to the IR approved abstract; PNNL-SA-194096. --- Verification that equipment is authentic and not changed; even at the circuit card assembly (CCA) level will likely be an important component of future arms control treaties. This effort was an initial evaluation of the potential for laser-based ultrasound (LBU) as an inspection tool for Unique Identification (UID) of Circuit Card Assembly (CCA) boards and CCA components. The LBU system used a laser pulse for ultrasound generation and an Optical Microphone for ultrasound detection to image subsurface structures without physical contact and in a dry state. This paper described the selected CCA surrogate, CCA components that were examined, the LBU system, LBU images of the CCA components, and the initial development of UID algorithms. Receiver operating characteristics (ROC) curves indicated good performance for two algorithms as a potential means for UID of CCA boards and CCA components.

Laser Ultrasound, Equipment Verification, Arms Con↗
NASA NTRS1989

Flexural fatigue life prediction of closed hat-section using materially nonlinear axial fatigue characteristics

Straight or curved hat-section members are often used as structural stiffeners in aircraft. For instance, they are employed as stiffeners for the dorsal skin as well as in the aerial refueling adjacent area structure in F-106 aircraft. The flanges of the hat-section are connected to the aircraft skin. Thus, the portion of the skin closing the hat-section interacts with the section itself when resisting the stresses due to service loads. The flexural fatigue life of such a closed section is estimated using materially nonlinear axial fatigue characteristics. It should be recognized that when a structural shape is subjected to bending, the fatigue life at the neutral axis is infinity since the normal stresses are zero at that location. Conversely, the fatigue life at the extreme fibers where the normal bending stresses are maximum can be expected to be finite. Thus, different fatigue life estimates can be visualized at various distances from the neural axis. The problem becomes compounded further when significant portions away from the neutral axis are stressed into plastic range. A theoretical analysis of the closed hat-section subjected to flexural cyclic loading is first conducted. The axial fatigue characteristics together with the related axial fatigue life formula and its inverted form given by Manson and Muralidharan are adopted for an aluminum alloy used in aircraft construction. A closed-form expression for predicting the flexural fatigue life is then derived for the closed hat-section including materially nonlinear action. A computer program is written to conduct a study of the variables such as the thicknesses of the hat-section and the skin, and the type of alloy used. The study has provided a fundamental understanding of the flexural fatigue life characteristics of a practical structural component used in aircraft when materially nonlinear action is present.

Razzaq, Zia↗
NASA NTRS1980

Galilean satellite eclipse studies. I - Observations and satellite characteristics

Spectrophotometric light curves of 12 Galilean satellite eclipses are reported. The observations were made in 20 to 30 channels over the wavelength range 3240 to 10,500 A using the 200-in. telescope. The initial data processing is described. These data measure the Jovian aerosol content in the lower stratosphere and uppermost troposphere and the methane abundance in the lower stratosphere. The data are consistent with a lack of limb darkening on the Galilean satellites. The orbit of Callisto is shown to be inclined 0.08 + or - 0.02 deg to the equatorial plane of Jupiter.

Greene, T. F.↗
DOE OSTI2024

Nanoscale Probing of Electrical Memory Effects in van der Waals Layered PdSe 2

Tunable electronic materials that can be switched between different impedance states are fundamental to the hardware elements for neuromorphic computing architectures. This “brain-like” computing paradigm uses highly paralleled and colocated data processing, leading to greatly improved energy efficiency and performance compared to traditional architectures in which data have to be frequently transferred between processor and memory. In this work, we use scanning microwave impedance microscopy for nanoscale electrical and electronic characterization of two-dimensional layered semiconductor PdSe 2 to probe neuromorphic properties. The local resolution of tens of nanometers reveals significant differences in electronic behavior between and within PdSe 2 nanosheets (NSs). In particular, we detected both n-type and p-type behaviors, although previous reports only point to ambipolar n-type dominating characteristics. Nanoscale capacitance–voltage curves and subsequent calculation of characteristic maps revealed a hysteretic behavior originating from the creation and erasure of Se vacancies as well as the switching of defect charge states. In addition, stacks consisting of two NSs show enhanced resistive and capacitive switching, which is attributed to trapped charge carriers at the interfaces between the stacked NSs. Stacking n- and p-type NSs results in a combined behavior that allows one to tune electrical characteristics. In conclusion, as local inhomogeneities of electrical and electronic behavior can have a significant impact on the overall device performance, the demonstrated nanoscale characterization and analysis will be applicable to a wide range of semiconducting materials.

2D material↗
NASA NTRS1995

Electron and proton damage on InGaAs solar cells having an InP window layer

As part of a continuing program to determine the space radiation resistance of InP/ln(0.53)Ga(0.47)As tandem solar cells, n/p In(0.53)Ga(0. 47)As solar cells fabricated by RTI were irradiated with 1 MeV electrons and with 3 MeV protons. The cells were grown with a 3 micron n-lnP window layer to mimic the top cell in the tandem cell configuration for both AMO solar absorption and radiation effects. The results have been plotted against 'displacement damage dose' which is the product of the nonionizing energy loss (NIEL) and the particle fluence. A characteristic radiation damage curve can then be obtained for predicting the effect of all particles and energies. AMO, 1 sun solar illumination IV measurements were performed on the irradiated InGaAs solar cells and a characteristic radiation degradation curve was obtained using the solar cell conversion efficiency as the model parameter. Also presented are data comparing the radiation response of both n/p and p/n (fabricated by NREL) InGaAs solar cells as a function of base doping concentration. For the solar cell efficiency, the radiation degradation was found to be independent of the sample polarity for the same base doping concentration.

Messenger, Scott R.↗
NASA NTRS1942

Investigation in the 7-by-10 Foot Wind Tunnel of Ducts for Cooling Radiators within an Airplane Wing

Report presents the results of an investigation made in the NACA 7 by 10-foot wind tunnel of a large-chord wing model with a duct to house a simulated radiator suitable for a liquid-cooled engine. The duct was expanded to reduce the radiator losses, and the installation of the duct and radiator was made entirely within the wing to reduce form and interference drag. The tests were made using a two-dimensional-flow setup with a full-span duct and radiator. Section aerodynamic characteristics of the basic airfoil are given and also curves showing the characteristics of the various duct-radiator combinations. An expression for efficiency, the primary criterion of merit of any duct, and the effect of the several design parameters of the duct-radiator arrangement are discussed. The problem of throttling is considered and a discussion of the power required for cooling is included.

Harris, Thomas A↗
NASA NTRS2004

High Efficiency Thermoelectric Radioisotope Power Systems

The work performed and whose results presented in this report is a joint effort between the University of New Mexico s Institute for Space and Nuclear Power Studies (ISNPS) and the Jet Propulsion Laboratory (JPL), California Institute of Technology. In addition to the development, design, and fabrication of skutterudites and skutterudites-based segmented unicouples this effort included conducting performance tests of these unicouples for hundreds of hours to verify theoretical predictions of the conversion efficiency. The performance predictions of these unicouples are obtained using 1-D and 3-D models developed for that purpose and for estimating the actual performance and side heat losses in the tests conducted at ISNPS. In addition to the performance tests, the development of the 1-D and 3-D models and the development of Advanced Radioisotope Power systems for Beginning-Of-Life (BOM) power of 108 We are carried out at ISNPS. The materials synthesis and fabrication of the unicouples are carried out at JPL. The research conducted at ISNPS is documented in chapters 2-5 and that conducted at JP, in documented in chapter 5. An important consideration in the design and optimization of segmented thermoelectric unicouples (STUs) is determining the relative lengths, cross-section areas, and the interfacial temperatures of the segments of the different materials in the n- and p-legs. These variables are determined using a genetic algorithm (GA) in conjunction with one-dimensional analytical model of STUs that is developed in chapter 2. Results indicated that when optimized for maximum conversion efficiency, the interfacial temperatures between various segments in a STU are close to those at the intersections of the Figure-Of-Merit (FOM), ZT, curves of the thermoelectric materials of the adjacent segments. When optimizing the STUs for maximum electrical power density, however, the interfacial temperatures are different from those at the intersections of the ZT curves, but close to those at the intersections the characteristic power, CP, curves of the thermoelectric materials of the adjacent segments (CP = T(sup 2)Zk and has a unit of W/m). Results also showed that the number of the segments in the n- and p-legs of the STUs optimized for maximum power density are generally fewer than when the same unicouples are optimized for maximum efficiency. These results are obtained using the 1-D optimization model of STUs that is detailed in chapter 2. A three-dimensional model of STUs is developed and incorporated into the ANSYS commercial software (chapter 3). The governing equations are solved, subject to the prescribed

El-Genk, Mohamed↗
NASA NTRS1938

Investigation in the 7-By-10 Foot Wind Tunnel of Ducts for Cooling Radiators Within an Airplane Wing, Special Report

An investigation was made in the NACA 7- by 10-foot wind tunnel of a large-chord wing model with a duct to house a simulated radiator suitable for a liquid-cooled engine. The duct was expanded to reduce the radiator losses, and the installation of the duct and radiator was made entirely within the wing to reduce form and interference drag. The tests were made using a two-dimensional flow set-up with a full-span duct and radiator. Section aerodynamic characteristics of the basic airfoil are given and also curves showing the characteristics of the various duct-radiator combinations. An expression for efficiency, the primary criterion of merit of any duct, and the effect of the several design parameters of the duct-radiator arrangement are discussed. The problem of throttling is considered and a discussion of the power required for cooling is included. It was found that radiators could be mounted in the wing and efficiently pass enough air for cooling with duct outlets located at any point from 0.25c to 0.70c from the wing leading edge on the upper surface. The duct-inlet position was found to be critical and, for maximum efficiency, had to be at the stagnation point of the airfoil and to change with flight attitude. The flow could be efficiently throttled only by a simultaneous variation of duct inlet and outlet sizes and of inlet position. It was desirable to round both inlet and outlet lips. With certain arrangements of duct, the power required for cooling at high speed was a very low percentage of the engine power.

Harris, Thomas A.↗
NASA NTRS1981

Heat transfer in cooled porous region with curved boundary

Heat transfer characteristics are analyzed for a cooled two-dimensional porous medium having a curved boundary. A general analytical procedure is given in combination with a numerical conformal mapping method used to transform the porous region into an upper half plane. To illustrate the method, results are evaluated for a cosine shaped boundary subjected to uniform external heating. The results show the effects of coolant starvation in the thick regions of the medium, and the extent that internal heat conduction causes the heated surface to have a more uniform temperature.

Siegel, R.↗
NASA NTRS1983

Vibrations of cantilevered doubly-curved shallow shells

Vibrational characteristics are determined for a previously unsolved class of problems, that of doubly-curved shallow shells having rectangular planforms, clamped along one edge and free on the other three. The solution procedure uses the Ritz method with algebraic polynomial trial functions. Convergence studies are made, and accurate frequencies and contour plots of mode shapes are presented for various curvature ratios, including spherical, circular cylindrical and hyperbolic paraboloidal shells. Particular emphasis is given to the effect of adding spanwise curvature to shells having chordwise curvature; numerous published references already exist for the case of zero spanwise curvature. The effects of changing aspect ratio, thickness ratio and Poisson's ratio are also studied.

Leissa, A. W.↗
DOE OSTI2020

Climate-Related Trends of Within-Storm Intensities Using Dimensionless Temporal-Storm Distributions

Huff curves are probabilistic time distributions of rainfall expressed as dimensionless cumulative percentages of storm depth and duration. Previous studies have documented development factors, spatial robustness, and the utility of Huff curves in practical applications. However, the effects of trending rainfall on Huff curve intensity patterns have not yet been studied. As such, the goal of this paper is to fill this gap by studying Huff curve patterns in a watershed with demonstrated increasing trends of temperature and precipitation, with the intention that it can be generalized to other areas in the US and the world. To achieve this goal, the high temporal resolution precipitation data collected from a high spatial density, 72-year precipitation-gauge network on the 4.25-km 2 North Appalachian Experimental Watershed in east-central Ohio were used. Seasonal storm pattern trends from 1939 to 2010 were investigated using dimensionless depth (with the frequency of 50%, $d_{50}$) and the curve variability $(V = d_{80} - d_{20})$ at three dimensionless within-storms time periods (three verticals). The Spearman rank correlation procedure (correlation coefficient, ρ and significance probability, p) was used to statistically determine trends over time using 8 periods of 4-season sets of Huff curves over the 72 years. Two averages of ρ and p were computed: (1) by averaging the individual ρ and p obtained from 10 gauges (AvgI); and (2) by grouped averaging of all individual gauge values of $d_{50}$ and V and then computing ρ and p (AvgG). The test results of individual gauges showed that 4 cases for $d_{50}$ and 23 cases for V were significant for all seasons and verticals (total of 120 cases for each variable). The test results of AvgI for $d_{50}$ and V and AvgG for $d_{50}$ showed no significant trends in all seasons and verticals. Only the AvgG for V led to a significant trend for V in spring and fall at different times within storm patterns. The data do not provide sufficient evidence at the p=0.05 significance level to reject the null hypothesis of unchanging position of the dimensionless depth of the 50% Huff curves for individual or averages for all seasons and verticals. Also, there is insufficient evidence to reject the null hypothesis of unchanging variability, V, using the average ρ of individual gauges (AvgI for V) for all seasons and verticals. AvgG results showed a significant trend in V; however, this analysis may be affected by the nonindependence of storm data. The results suggest that it is likely that there is little if any effect of trending climate over approximately 70 years on Huff curve patterns. The results of this study add to the robustness characteristics of Huff curves and to their potential use in hydrological practice as design storms, as the foundation of stochastic storm generation, and for storm disaggregation, and they deserve further investigation. These different forms of inputs to watershed models have the potential to improve runoff estimation. The results suggest that, if verified in other studies, they have applicability to provide useful stationary precipitation patterns across the US and other areas of the world in areas of nonstationary climate. Also, individual rain gauge data may not be representative of trends even over small areas, and seasonal differences were noticeable as found in other studies. Recommendations are provided.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1987

Forced convective heat transfer in curved diffusers

Measurements of the velocity characteristics of the flows in two curved diffusers of rectangular cross section with C and S-shaped centerlines are presented and related to measurements of wall heat transfer coefficients along the heated flat walls of the ducts. The velocity results were obtained by laser-Doppler anemometry in a water tunnel and the heat transfer results by liquid crystal thermography in a wind tunnel. The thermographic technique allowed the rapid and inexpensive measurement of wall heat transfer coefficients along flat walls of arbitrary boundary shapes with an accuracy of about 5 percent. The results show that an increase in secondary flow velocities near the heated wall causes an increase in the local wall heat transfer coefficient, and quantify the variation for maximum secondary-flow velocities in a range from 1.5 to 17 percent of the bulk flow velocity.

Rojas, J.↗
NASA NTRS1976

A study of sound transmission in curved duct bends by the Galerkin method

A computational procedure based on the Galerkin method is developed to study the sound transmission and reflection characteristics of circularly curved bends of rectangular ducts. This procedure is adaptable to routine computer calculation. An important component of the computer program consists of a QR iterative algorithm which solves the matrix eigenvalue problem generated by the Galerkin method. The present procedure produced very satisfactory convergent results when applied even to cases where the incident wave has high frequency and high wave mode numbers. Some properties of the Galerkin solution are investigated. Its relationship to the classical solution by the method of separation of variables is discussed.

Tam, C. K. W.↗
NASA NTRS1981

Curved-channel microchannel array plates

The microchannel array plate (MCP) is a photoelectric detector with an imaging capability comparable to that of a photographic plate. Recently MCPs in which the channels are curved to inhibit ion feedback have become available. These devices represent a major advance in MCP technology, since a single curved-channel MCP can be operated stably at high gain in the pulse-counting mode without any of the problems of stability of response or short lifetime reported for 'chevron' MCP detectors. Attention is given to the mode of operation of channel electron multipliers (CEM) and MCP, curved-channel MCP, test procedures, and performance characteristics. The accumulated test data show that the fundamental operating characteristics of the curved-channel MCP are directly related to those for the CEM.

Timothy, J. G.↗