Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CONTACT RESISTANCE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Differences in Printed Contacts Lead to Susceptibility of Silicon Cells to Series Resistance Degradation

Here, in this case study, we investigate a degradation mode occurring at the cell level in fielded multi-Si modules. The modules exhibit a mix of affected and unaffected cells. Affected cells show a progressive, series-resistance-related power degradation as shown via module- and cell-level IV curves, along with electroluminescence (EL) and PL imaging at the module, cell, and cell core sample scales. Scanning electron microscopy and energy-dispersive X-ray spectroscopy reveal a difference in the oxides in the silver paste used in screen printing of the gridline contacts. The paste in the affected cells is lead rich, whereas the paste in the unaffected cells is zinc rich. This suggests that the cells were screen printed with different silver paste compositions and possibly firing conditions, and that the different composition correlates with the susceptibility to degradation. Our results indicate degradation of the contact at the oxide-silver interface, causing a severe increase in series resistance across the cell that continues to progress over time.

14 SOLAR ENERGY↗
DOE OSTI2022

Investigation of the Interactions Between Low-Temperature Ag Paste Components and SiO2/Poly-Si(n) Contacts and the Impact on Contact Properties

Reducing poly-Si thickness to minimize parasitic absorption on a light-receiving side of a TOPCon solar cell without suffering voltage losses after metallization is a challenge in optimizing TOPCon performance. As an alternative to fire-through pastes, we investigate low-temperature Ag paste to SiO2/poly-Si passivating contacts through fabrication of electrical test structures to characterize the passivation quality and electrical transport across the metallized interface. With current paste chemistries, we find that solvent wetting of the poly-Si surface before evaporation and non-volatile binder resin adhesion to the surface after curing are major impediments which prevent Ag contact formation. However, low- resistance poly-Si/Ag interfaces formed with physical vapour deposition similarly degrade after annealing, indicating contacting issues related to the Ag content even in the absence of the organic paste components.

low temperature Ag paste↗
DOE OSTI2023

Electrical Analysis of Pulsed Laser Annealed Poly-Si: Ga/SiOx Passivating Contacts

In this contribution, we examine Ga hyper-doped poly-Si/SiOx contacts realized by pulsed laser melting (PLM). Here, we use Ga as a novel p-type dopant and B as a conventional dopant to induce non-equilibrium doping using an excimer laser. We perform simulations to visualize the maximum melt depth profiles within the poly-Si, with a goal of distributing dopants close to the tunneling oxide, but at the same time preserving the passivation. Hall measurements show that sheet resistance for B is lower than Ga due to its higher solid solubility limit in Si. After comparing the Hall active dopant concentration with the chemical concentration obtained by SIMS measurement, we show nearly 100% activation B activation reaching 10^21 cm-3, while only ~20% activation for Ga. Nevertheless, we achieve active doping concentrations of Ga in poly-Si six times higher than its solid solubility limit in Si (~10^19 cm-3). We compare our Hall mobilities with values in the literature for c-Si and show that B mobilities in laser-treated poly-Si are close to that of the literature value for B, while Ga mobilities are lower, possibly due to additional scattering channels within grain boundaries and deformed lattice. We also compare our results on PLM samples with conventional furnace annealed samples, and we show much higher percent activation and mobilities. Previously, we showed a low contact resistivity of 35.5 +/- 2.4 m..omega..cm2. Here, we further confirm this result by scanning spreading resistance microscopy and Kelvin force nanoprobe microscopy. We demonstrate that our poly-Si: Ga/nCz contact exhibits large drift and diffusion currents under normal cell operating voltage, which widens the laser processing window for a good metal/poly-Si/c-Si contact.

high-efficiency solar cells↗
DOE OSTI2024

Laser‐Sintered Silver Metallization for Silicon Heterojunction Photovoltaic Cells

Herein, a novel metallization technique is reported for crystalline silicon heterojunction (SHJ) solar cells in which silver (Ag) fingers are printed on the SHJ substrates by dispensing Ag nanoparticle‐based inks through a needle and then sintered with a continuous‐wave carbon dioxide (CO 2 ) laser. The impact of the Ag ink viscosity on the line quality and the line resistance is investigated on three Ag inks with different viscosities. Increasing ink viscosity yields higher Ag contact heights, larger aspect ratios, and lower line resistance values. The Ag line height increases from less than a micrometer to ≈18.62 ± 3.48 μm with the increasing viscosity. Photoluminescence imaging shows that the low‐resistance Ag metal contacts obtained do not result in any passivation damage of the SHJ substrate. This is because the wavelength of light emitted from the CO 2 laser (i.e., 10.6 μm) leads to optical absorption in the Ag, but this light is effectively transparent to the transparent conductive oxide film, amorphous silicon films, and crystalline silicon substrate. Bulk resistivity values as low as 6.5 μΩ cm are obtained for the laser‐sintered Ag contact and printed using the Ag ink with the highest viscosity in this work.

Mousumi, Jannatul Ferdous↗
DOE OSTI2024

Navigating high-dimensional process-structure–property relations in nanocrystalline Pt-Au alloys with machine learning

For decades, materials scientists have relied on the process-structure–property paradigm to guide investigations into material behaviors. Traditional studies often examine a limited number of process-structure–property variables, striving to elucidate mechanisms governing material response. However, this approach is time consuming and can limit exploration, as well as the discovery of process-structure–property relations in novel materials. In this paper, we combined combinatorial sputter deposition and multi-modal high-throughput materials characterization with feedforward neural networks to establish high-dimensional process-structure–property relations in Pt-Au alloys, yielding nanocrystalline alloys with high hardness and low resistivity relevant to electrical contact switch applications. We mapped three indicators of process conditions (composition and two atomic deposition characteristics) onto four indicators of material structure (X-ray diffraction, film thickness, density, and surface roughness) and two indicators of material properties (hardness and resistivity), resulting in 784 unique combinations evaluated over a 13-dimensional space. The neural networks predicted Pt-Au alloys with 18–24 at.% Au, when deposited at specific conditions, to have a nanoindentation hardness up to 7.2 GPa. This high hardness value, comparable to some steels, represents a 3-fold improvement in hardness over “hard gold”, a commonly used electrical contact alloy, while maintaining requisite electrical conductivity. The neural network models provide an avenue to identify expected process windows capable of maximizing material performance.

Electrical contact materials↗
DOE OSTI2020

Wireless oxygen dosimeter

A tag for detecting an analyte can include a radio frequency identification tag including a sensor portion, the sensor portion configured to change resistivity when the radio frequency identification tag contacts or interacts with an analyte, whereby the resistivity change alters an output of the radio frequency identification tag, wherein the sensor portion includes a circuit, and wherein the sensor portion is configured to activate the circuit or deactivate the circuit when contacted or having interacted with the analyte, wherein the sensor portion includes a conductive material associated with a polymer complex.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Li + /H + Exchange in Solid-State Oxide Li-Ion Conductors

Understanding the moisture stability of oxide Li-ion conductors is important for their practical applications in solid-state batteries. Unlike sulfide or halide conductors, oxide conductors generally better resist degradation when in contact with water but can still undergo topotactic Li + /H + exchange (LHX). Here, we combine density functional theory (DFT) calculations with a machine-learning interatomic potential model to investigate the thermodynamic driving force of the LHX reaction for two representative oxide Li-ion conductor families: garnets and NASICONs. Li-stuffed garnets exhibit a strong driving force for proton exchange due to their high Li chemical potential. In contrast, NASICONs demonstrate a higher resistance against proton exchange due to the lower Li chemical potential and the lower O–H bond covalency for polyanion-bonded oxygens. Our findings reveal a critical trade-off: Li stuffing enhances conductivity but increases moisture susceptibility. This study underscores the importance of designing Li-ion conductors that possess both high conductivity and high stability in practical environments.

Li, Zhuohan [Lawrence Berkeley National Laboratory↗
DOE OSTI2024

MgB$_{2}$ Coating by HPCVD for 1.3-GHz Superconducting RF Cavities

While MgB 2 possesses promising material parameters for SRF cavities with higher Q, higher gradient, and higher operation temperatures than Nb cavities, such cavity properties have not been demonstrated using MgB 2 . As part of a continuing effort to fabricate MgB 2 -coated SRF cavities by hybrid physical chemical vapor deposition (HPCVD), we present here an HPCVD system design for coating the inside wall of 1.3-GHz copper cavities with MgB 2 . The cavity is heated using a pair of clamshell resistive heaters that directly contact the cavity body. Here, the new heater design is more compact and requires less power to reach the deposition temperature (~500°C for MgB 2 deposition on copper.) Preliminary test of MgB 2 films grown on small copper substrates, mounted at different locations on the cavity, shows T c of 28.4 ~ 34.3 K, measured by AC susceptibility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Wettability Effects on Falling Film Flow and Heat Transfer Over Horizontal Tubes in Jet Flow Mode

The performance of a falling-film heat exchanger is strongly linked to the surface characteristics and the heat transfer processes that take place over the tubes. The primary aim of this numerical study is to characterize the influence of surface wettability on the film flow behavior and its associated surface heat transfer in the jet-flow mode. Volume of fluid (VOF) based simulations are carried out for horizontal tubes with different surface wettabilities. The wettability of the tube surfaces is represented using the Kistler's dynamic contact angle model. Surface wettability effects ranging from superhydrophilic to superhydrophobic are studied by varying the equilibrium contact angle from 2 deg to 175 deg. Two different liquid mass flow rates of 0.06 and 0.18 kg/m-s corresponding to the inline and staggered jet flow modes are studied. Results are presented in terms of the liquid film thickness, the contact areas between the different phases (solid–liquid and liquid–air), and the heat transfer coefficient or Nusselt number. The resistance imposed by the increasing contact angles inhibits the extent of the liquid spreading over the tube surface, and this, in turn, influences the liquid film thickness, and the wetted area of the tube surface. A significant decrement in the heat transfer rate from the tube surfaces was observed as the equilibrium contact angle increased from 2 deg to 175 deg. The local distributions of the Nusselt number over the tube surface are strongly influenced by the flow recirculation in the liquid bulk.

Engineering↗
DOE OSTI2023

CsPbBr3 perovskite single crystals for X- and -radiation detectors

Methods were developed for the synthesis and growth of halide lead perovskites CsPbBr3, which can be used as detectors of optical, X-ray, and -radiation. The growth of single crystals was carried out by the Bridgman method in quartz ampoules using zone-refined starting material. The electro-physical properties of the inorganic perovskite lead cesium tribromide CsPbBr3 were studied. Two types of structures with Cr/CsPbBr3/Ni rectifying and Ni/CsPbBr3/Ni ohmic contacts were fabricated. The resistivity of (  7×109 Ohmcm), and the activation energy of the dark conductivity (E  0.8 eV) were determined. From the measurements of the optical transmission spectra, the CsPbBr3 energy gap at 300 K was found to be Еg = 2.27 eV. The temperature dependence of the forbidden gap (Eg(T) = 2.4 - 4*10-4 T, eV) was also determined. A significant increase in photosensitivity for the Cr/CsPbBr3/Ni structure was observed at elevated temperatures. The Cr/CsPbBr3/Ni structures were shown to be sensitive to -radiation. The FWHM of the energy resolution for 241Am source was measured to be 15.8 keV.

Sklyarchuk, V.↗
DOE OSTI2026

Plasticizer-Free Gradient-Crosslinked Polyurethane Electrolyte for Room-Temperature Solid-State Lithium Batteries

Polymer-based solid-state electrolytes are promising for next-generation lithium metal batteries, yet their limited ionic conductivity and mechanical stability at ambient conditions remain key challenges. Herein, we report a novel gradient crosslinked polymer electrolyte (PU/PUA/PU) synthesized via a sequential in situ UV-curing process that integrates a mechanically robust polyurethane acrylate (PUA) core with soft linear polyurethane (PU) interfaces. This all-solid membrane operates without any liquid plasticizer and the interfacial PU layers ensure low interfacial resistance and intimate electrode contact, while the PUA core provides enhanced dimensional stability and dendrite suppression. As a result, the gradient electrolyte delivers an impressive ∼2.6 × 10 −4 S cm −1 ionic conductivity at 25 °C (two orders of magnitude higher than conventional PEO) and remains electrochemically stable >5 V (vs Li + /Li). Structural analysis confirms the formation of a well-defined crosslinked network with suppressed crystallinity and expanded interchain spacing. Electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) further validate these properties. When applied in a Li||NMC811 cell, the PU/PUA/PU electrolyte delivers stable cycling with high capacity at both 60 °C and 25 °C, demonstrating its potential for room-temperature solid-state battery applications without reliance on plasticizers or heating. In conclusion, this gradient design offers a practical path toward ambient-condition operation of solid-state lithium batteries, providing a paradigm for overcoming the traditional trade-off between ionic conductivity and mechanical robustness.

25 ENERGY STORAGE↗
DOE OSTI2020

Towards a high-performance garnet-based solid-state Li metal battery: A perspective on recent advances

Garnet-based solid-state Li metal batteries have been widely considered one of the most promising next-generation energy storage systems. However, the performance of these batteries is plagued by various limitations caused by the solid-state electrolyte (SSE). The poor wetting of lithium on the garnet surface diminishes the contact between the anode and electrolyte, leading to extremely high anode interfacial resistance. Similarly, the point-to-point contact between the cathode and electrolyte leads to high impedance on the cathode side. Moreover, although the SSE serves a firm barrier separating the anode and cathode, lithium dendrites can still grow through, causing a short circuit. Lastly, the solid/solid interface cannot be well maintained under cycling at high current density and capacity. Recently, remarkable progress has been achieved in garnet electrolyte to resolve these problems towards the aim of a high-performance solid-state Li metal battery. In this perspective, we highlight various recent advances in the field of garnet-based solid-state battery, including improving the anode/electrolyte interface, lithium dendrite detection, reducing cathode impedance, and electrolyte architecture design.

25 ENERGY STORAGE↗
DOE OSTI2021

Evaluation of Stripping Resistance of Organoclay-Modified Asphalt Binder and Aggregate Systems Using an Optical Contact Angle Analyzer

Organoclays, often referred to as nanoclays (NCs), are organically modified phyllosilicates. They are derived from naturally occurring clay minerals and possess unique characteristics in improving the physical and mechanical properties of polymers and rubbers. Recently, NCs have drawn interest in the modification of asphalt binders as micro-scale fillers. A few recent studies have revealed that the addition of NCs in asphalt binders improved binders’ stiffness, aging characteristics, and fatigue resistance. This study aims to evaluate the changes in moisture resistance of different NC-modified asphalt binders through the surface free energy (SFE) technique. This technique estimates SFE properties of binders and aggregates from static contact angle (SCA) data measured from an optical contact angle analyzer (OCA). Further, this study examines the changes in chemical compositions (functional groups) of binders due to the addition of selected NCs by using the Fourier Transformation Infrared (FTIR) technique. To this end, a commonly used performance grade (PG) binder (PG 64-22) modified with four different types (shape and size) of NCs, namely, Cloisite® 15 (C-15), Cloisite® 20 (C-20), Cloisite® Na+ (C-Na), and Cloisite® Ca++ (C-Ca) were evaluated in this study. The SFE data of five different types of aggregates from Oklahoma, namely, Davis Limestone (DL), Snyder Granite (SG), Dolese-Cooperton Limestone (DCL), Hanson-Davis Rhyolite (HDR), and Martin-Marietta-Mill-Creek Granite (MMMG), were used to perform their compatibility with the aforementioned NC-modified binders. The FTIR spectra revealed the presence of various alcohols, ethers, and esters in NC-modified asphalt binders. The moisture susceptibility analysis shows that the addition of NC results in an increase of SFE and cohesive energy of an asphalt binder, which are desired for improved moisture resistance. The addition of NC also shows improved compatibility in cases of all aggregates. Among the five aggregates, MMMCG showed the highest compatibility with all binders, followed by DCL, HDR, DL, and SG. In regard to NCs, the C-15 sample showed the highest compatibility followed by C-20, C-Na, and C-Ca.

Hossain, Zahid↗
DOE OSTI2023

Application of the van der Pauw method for electrical conductivity measurements at high temperatures using an insulating compressing ring

High quality data on the high temperature electrical properties of ceramics, particularly oxides, is of great value for material selection, design, and modeling for a broad range of emerging applications. Utilizing the mismatch in the coefficient of thermal expansion between two materials, a purely mechanical method for establishing electrical contact in the van der Pauw geometry to measure the bulk resistivity of ceramic disks at high temperatures is presented. Measurements of a reference material, 20 mol. % Gd-doped cerium oxide, are presented up to 1000 °C. The viability of electrical measurements up to a maximum temperature of 1600 °C is also considered. Measurements are performed using multiple techniques and compared to literature values finding excellent agreement. Finally, the approach described in this work enables the van der Pauw method to be applied to many ceramic materials over a wide range of temperatures and environments.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Differences in c-Si Solar Cell Metallization and Susceptibility to Series Resistance Degradation

In this case study, we investigate a degradation mode occurring at the cell level in fielded multi-Si modules. Affected cells in the module show a progressive, series-resistance-related power degradation observed in module- and cell-level IV curves along with EL and PL imaging at the module, cell, and cell core sample scale. SEM and elemental analysis via EDS reveal a difference in the oxides in the silver paste used in screen printing of the finger contacts. This suggests that the cells were screen printed with different silver paste compositions and possibly firing conditions. One of these combinations leads to degradation of the contact at the interface between the cell and contact finger, causing severe series resistance across the cell that continues to progress over time.

acetic acid↗
DOE OSTI2020

Assessment of AFM - KPFM and SSRM for Measuring and Characterizing Materials Aging Processes

Atomic Force Microscopy (AFM), in conjunction with Peak Force Kelvin Probe Force Microscopy (PF-KPFM) and Peak Force Scanning Spreading Resistance Microscopy (PF-SSRM), was used to assess changes on thin metal films that underwent accelerated aging. The AFM technique provides a relatively easy, non-destructive methodology that does not require high-vacuum facilities to obtain nanometer-scale spatial resolution of surface chemistry changes. Surface morphology, roughness, contact potential difference, and spreading resistance were monitored to qualitatively identify effects of aging-morphology changes and oxidation of Au, Al, Cu thin film standards as well as diffusion of CuAu and AlAu thin film stacks at 65C under dried nitrogen flow conditions. AFM PF-KPFM and PF-SSRM modes have been exercised, refined and have proven to be viable and necessary early aging detection tools.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Low-cost, Highly Efficient and Fast Thermally Pressed Scalable Carbon-based Planar Perovskite Solar Cells

This Final Technical Report summarizes work completed under Award Number DEEE0009833, titled "Low-cost, Highly Efficient and Fast Thermally Pressed Scalable Carbon-based Planar Perovskite Solar Cells." The project addressed the central technical problem that carbon-electrode perovskite solar cells (C-PSCs) can reduce electrode costs and improve environmental durability, but they have historically lagged noble-metalcontact devices due to poor carbon/perovskite contact, high carbon-electrode resistance, imperfect hole extraction, and insufficient operational stability. The Statement of Project Objectives (SOPO), therefore, required systematic engineering of thermally pressed carbon-based planar perovskite solar cells by improving the carbon/perovskite interface quality, improving carbon-electrode conductivity, and further increasing device stability. The work advanced understanding of carbon-based perovskite photovoltaics by connecting device performance to three coupled mechanisms: interfacial recombination at the perovskite/hole-transport-layer/carbon stack; lateral and vertical transport losses in carbon contacts; and instability driven by moisture, heat, illumination, ion migration, and slow/variable manufacturing steps.

14 SOLAR ENERGY↗