Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Initial assessment of alternative carbon fiber geometries for design of cost-effective compressive performance: Size effect studies

Carbon fiber provides opportunity to reduce weight in structural composites, including wind turbine blades, due to the material's superior specific stiffness and specific strength compared to alternatives. Despite these advantages, cost and compressive performance are considered weaknesses for carbon fiber products available today. Studies to produce low-cost carbon fiber alternatives, including the use of textile-derived precursor systems, have shown progress and merit through the DOE/ORNL low-cost carbon fiber initiatives. Here, this work focuses on enabling increases in compressive strength through design of the carbon fiber geometry, applicable to both textile and conventional precursor systems, while also providing opportunities to reduce carbon fiber processing costs. Fiber-resin interface and fiber alignment are among the most frequently cited factors controlling composite compressive performance. However, it is believed that there is opportunity in traditionally unexplored routes to increasing compressive strength through alteration of the carbon fiber geometry by increasing the fiber area moment of inertia and/or the fiber perimeter and interfacial area. This paper presents initial results from manufacturing carbon fiber materials to assess the impacts of carbon fiber size on tested composite compressive performance with projected neutral or even beneficial impact on fiber and composite manufacturing economics. Carbon fiber systems with increasing size illustrate a favorable correlation for compressive performance greater than predicted from a micromechanical failure model. The manufacturing and mechanical test results support the hypothesis of this work that alterations to fiber geometry can be used to produce improvements of the compressive strength of carbon fiber reinforced polymers and provide incentive for related work in designing alternative shapes to further enhance compressive performance.

42 ENGINEERING↗
DOE OSTI2024

Integrated design of aluminum-enriched high-entropy refractory B2 alloys with synergy of high strength and ductility

Refractory high-entropy alloys (RHEAs) are promising high-temperature structural materials. Their large compositional space poses great design challenges for phase control and high strength-ductility synergy. The present research pioneers using integrated high-throughput machine learning with Monte Carlo simulations supplemented by ab initio calculations to effectively navigate phase selection and mechanical property predictions, developing single-phase ordered B2 aluminum-enriched RHEAs (Al-RHEAs) demonstrating high strength and ductility. These Al-RHEAs achieve remarkable mechanical properties, including compressive yield strengths up to 1.7 gigapascals, fracture strains exceeding 50%, and notable high-temperature strength retention. They also demonstrate a tensile yield strength of 1.0 gigapascals with a ductility of 9%, albeit with B2 ordering. Furthermore, we identify valence electron count domains for alloy ductility and brittleness with the explanation from density functional theory and provide crucial insights into elemental influence on atomic ordering and mechanical performance. The work sets forth a strategic blueprint for high-throughput alloy design and reveals fundamental principles governing the mechanical properties of advanced structural alloys.

Science & Technology - Other Topics↗
DOE OSTI2022

Molecular insights into the structure-property relationships of 3D printed polyamide reverse-osmosis membrane for desalination

3D-printing is an emerging method for manufacturing polyamide (PA) reserve osmosis (RO) membranes for water treatment and desalination, which can precisely control membrane structural properties, such as thickness, roughness, and resolution. However, the synthesis-structure (i.e., degree of cross-linking (DC), m-phenylenediamine/trimesoyl chloride (MPD/TMC) ratio, and membrane thickness) to property (permeability and water-salt selectivity) relationships for these membranes has not been well understood. At the same time, a microscopic understanding of the physical mechanism of water and salt transport is needed to guide the design of high-performance 3D-printed membranes and improve the printing efficiency. Furthermore, the atomic-scale transport features and energetics of water and salt ions are studied at high pressure for the 3D-printed PA RO membranes with the different DCs and MPD/TMC ratios through non-equilibrium molecular dynamics (NEMD) simulations. Factoring in membrane structure properties, rejection ratio of salt ions and pressure-dependent water flux, 3D-printed PA membranes having an MPD/TMC ratio of 3.0:2.0 and a DC between 80%~90% attains ideal performance: high water flux, high rejection of salt ions, and excellent structural integrity. Mechanistically, water permeability for highly cross-linked PA RO membranes depends on the temporary on-and-off channels that allow water molecules to jump from one cavity to another at high pressure. In addition, higher pressures cause rapid compaction of PA membranes’ free volume and membrane thickness. Membrane failure at high pressure is determined by the DC and MPD/TMC ratios-dependent compressive yield strength. In short, these findings provide physical insights for optimizing existing PA membranes and designing next-generation desalination membranes at the molecular level.

3D-printed PA RO membrane↗
DOE OSTI2021

Enhanced work hardening from oxygen-stabilized ω precipitates in an aged metastable β Ti-Nb alloy

High levels of oxygen in solid solution in Ti alloys are considered detrimental to mechanical properties because of embrittlement concerns. In metastable β titanium alloys, the formation of isothermal ω precipitates is also known to cause severe embrittlement and ductility reduction. However, oxygen has been shown to partition to the ω phase during ageing, and this partitioning behavior may potentially impact ω’s mechanical contribution. Using micropillar compression, we compared the deformation behavior of Ti-20Nb (at. %) with oxygen-stabilized ω precipitates to the behavior of oxygen-free specimens. The oxygen-stabilized microstructures showed increased compressive yield strength and enhanced work hardening behavior compared to oxygen-free specimens. In the absence of oxygen, the compressed pillars showed slip band formation and catastrophic failure, and transmission electron microscopy imaging revealed that ω precipitates were sheared within the continuous deformation channels resulting in slip localization. In contrast, oxygen-stabilized ω precipitates were harder to shear and the formation of continuous deformation channels was suppressed during compression, leading to improved work hardening behavior up to 15% strain. Furthermore, this counter-intuitive role of oxygen may offer design strategies to address the significant embrittlement and loss of ductility observed for ω-strengthened β Ti alloys without oxygen and avenues to expand the use of β Ti alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Hydrogel-assisted self-healing of biomineralized living building materials

Living building materials (LBMs) are an emergent class of structural materials that leverage the biomineralization capability of microorganisms within sand-hydrogel scaffolds to produce living, load-bearing structures. Here we produced LBMs using a physically crosslinkable sand-hydrogel scaffold and two microorganisms with different biomineralization pathways - Synechococcus sp. PCC 7002 (photosynthetic) and S. pasteurii (ureolytic) - and investigated their self-healing capacity. Our results reveal that both Synechococcus sp. PCC 7002 and S. pasteurii demonstrated exceptional viability within all LBMs for more than 20 days. Damaged LBMs containing Synechococcus sp. PCC 7002 exhibited 103% and 112% of their original compressive and flexural strengths, respectively, after three days of healing at 50% relative humidity (RH) (i.e., ambient conditions). In contrast, LBMs containing S. pasteurii exhibited 71% and 66% of their original compressive and flexural strengths, respectively, after three days of healing at 50% RH. The compressive and flexural strengths of all LBMs rebounded to 93-100% after seven days of healing at 50% RH. Data substantiate that the self-healing ability of the hydrogel plays a critical role in facilitating healing of LBMs, as evidenced by the 82-118% rebounds in compressive and flexural strengths by the sand-hydrogel scaffold alone after three or seven days of healing at 50% RH. Healing was less effective at 100% RH for all LBMs investigated herein.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic Strength of Iron at High Pressures and Strain Rates

Accurate modeling of meteorite impacts, and deformation of planetary cores require characterization of the flow strength and in-elasticity of iron in its different phases. In this letter, we investigate the flow strength of both the ambient α-phase and high-pressure ϵ-phase of iron at strain-rates of 1 × 10 5 s –1 and pressures up to 42 GPa using high pressure - pressure shear plate impact experiments. We report the strength of the ϵ-iron to be significantly higher than α-phase but consequently one order smaller than the previously reported dynamic strength at high pressures. As a result, the complete stress-strain response of the ϵ-phase is reported for the first time.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Dynamic Strength of Copper at High Pressures Using Pressure Shear Plate Experiments

Measurement of strength at high pressures is critical to understanding the behavior of materials subjected to extreme loading conditions. Recent developments have extended the pressure shear plate impact (PSPI) technique to the high-pressure regime. Such experiments provide a unique opportunity to extract the complete stress-strain behavior of materials at relatively high pressures. The modified technique includes a new fiber-optic heterodyne transverse velocity interferometer system and new analysis methods to account for the inelastic response of the anvil plates. In this study, PSPI experiments are conducted on oxygen-free high conductivity (OFHC) copper at pressures ranging from 10 to 43 GPa and at strain rates of ~10 5 s -1 . Complete stress-strain curves of copper are obtained using a hybrid methodology that relies on numerical simulations and particle velocity records gathered in these experiments. Experiments are conducted at similar pressures and strain rates using two types of anvils that undergo different levels of plastic strains: tool steel and tungsten carbide, to check the robustness of the hybrid method. The behavior of copper at these high pressures and strain rates is compared with previous literature data, and the effect of pressure and strain rate on the strength behavior of copper are discussed. Here, it was observed that the rate of change in yield strength change in pressure was 2.5 times the rate of change of shear modulus with pressure. The strength models that predict the response of copper at these extreme conditions are also examined and validated.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Multiscale Richtmyer-Meshkov instability experiments to isolate the strain rate dependence of strength

Theoretical analysis of Richtmyer-Meshkov instability (RMI) experiments for solid strength shows that the strain rate for a given shock should be inversely proportional to the length scale of the sine wave perturbations when η 0 k , the nondimensional amplitude to wavelength ratio, is held fixed. To isolate the effect of strain rate on strength, free-surface RMI specimens of annealed copper were prepared with three perturbation regions with the same η 0 k but different length scales, characterized by the wavelength λ varying by a factor of 4.9 from 65 to 130 to 320 µ m . Three such targets with different fixed η 0 k ′ s were impacted to a shock pressure of 25 GPa, and the instability evolution was measured with photon Doppler velocimetry. Strengths estimated by comparing hydrocode simulation to the data increased from 700 to 1200 MPa as λ decreased. The different η 0 k targets exercised increasing amounts of plastic strain yet showed no evidence of strain hardening. Physical regime sensitivity analysis determined that for 320 − 65 µ m wavelength perturbations, the effective strain rates increased from 8.7 × 10 6 to 3.3 × 10 7 s − 1 , a factor of 3.8. Thus, the predicted strain rate scaling was mostly achieved but slightly suppressed by increased strength at higher rates. The RMI strength estimates were plotted against constitutive testing data on copper from the literature to show striking evidence of the strength upturn at higher strain rates. Published by the American Physical Society 2024

36 MATERIALS SCIENCE↗
DOE OSTI2023

Review of supplementary cementitious materials with implications for age-dependent concrete properties affecting precast concrete

Here, this paper presents a comprehensive review of existing research examining the effects of supplementary cementitious materials on age-dependent concrete properties with the most profound implications for precast concrete production. The review covers the physical and chemical properties of selected types of supplementary cementitious materials, concrete mixture proportions, concrete curing methods, testing procedures, and test results related to the fresh properties and strengths of a range of concrete mixtures. Although the use of supplementary cementitious materials in precast concrete products is common, the detailed information provided in this paper may facilitate more widespread use of these materials to enhance concrete properties and comply with sustainability initiatives.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Equation of state and strength of diamond in high-pressure ramp loading

Diamond is used extensively as a component in high-energy-density experiments, but existing equation of state (EOS) models do not capture its observed response to dynamic loading. In particular, in contrast with first-principles theoretical models of equilibrium multiphase EOS, no solid-solid phase changes have been detected, and no general-purpose EOS models match the measured ambient isotherm. We have performed density functional theory (DFT) calculations of the diamond phase to ~10 TPa, well beyond its predicted range of thermodynamic stability, and used these results as the basis of a Mie-Grüneisen EOS. We also performed DFT calculations of the elastic moduli, and calibrated an algebraic elasticity model for use in simulations. We then estimated the flow stress of diamond by comparison with the stress-density relation measured experimentally in ramp-loading experiments. Furthermore, the resulting constitutive model allows us to place a constraint on the Taylor-Quinney factor (the fraction of plastic work converted to heat) from the observation that diamond does not melt on ramp compression.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Vanishing dynamic strength measured in a transient high-pressure phase of tin

This work reports two independent experimental estimations of the dynamic strength of the body-centered tetragonal (bct) 𝛾 phase of tin, which occurs at pressures above about 9 GPa and transforms promptly back to the ambient 𝛽 phase upon pressure release. Measuring strength in such a transient high-pressure phase is challenging. One measurement used free-surface Richtmyer-Meshkov instabilities generated with gas gun impact. Another set of measurements used ramp-release loading in a pulsed-power facility. Strength estimations came from comparison to simulations using a comprehensive multiphase modeling framework that includes equation of state, shear moduli, and strength separately for each phase, and treats mixed-phase regions. Both experimental methods found the 𝛾-phase strength to be very low, within experimental uncertainty of zero. The existing literature on other materials, by contrast, almost universally reports higher strength in transient high-pressure phases compared with ambient phases. Recent Molecular-Dynamics simulations on tin in the literature showed almost zero deviatoric strength during a deformation-induced bct → bct transformation in which one of the 𝛾-phase 𝑎 axes “flips” to the 𝑐 axis. This reorientation currently provides the most plausible explanation for the low observed strength in 𝛾-phase tin.

36 MATERIALS SCIENCE↗
DOE OSTI2026

At Extreme Strain Rates, Pure Metals Thermally Harden while Alloys Thermally Soften

When materials are deformed at extreme strain rates, >10 6 s -1 , a counterintuitive mechanical response is seen where the strength and hardness of pure metals increases with increasing temperature. This anti-thermal hardening is due to dislocations meeting resistance to their motion from phonons in the crystal lattice. However, here, using optically-driven microballistic impact testing to measure dynamic strength and hardness, we show that when the composition is systematically varied away from high purity, the mechanical response of metals transitions from phonon drag of dislocations back to thermally activated pinning of dislocations, even at the highest strain rates. This boundary from “hotter-is-stronger” to “hotter-is-softer” is observed and mapped for nickel, titanium and gold. Furthermore, the ability to tune between deformation mechanisms with very different temperature dependencies speaks to new directions for alloy design in extreme conditions.

Ballistic transport↗
DOE OSTI2022

Strengthening Mechanisms and Deformation Behavior of Industrially-Cast and Lab-Cast Dual-Phase High Entropy Alloy

An iron-rich high entropy alloy Al 0.65 CoCrFe 2 Ni comprising of both FCC and BCC phases was designed and fabricated using induction melting at a large industrial scale and suction casting at a small lab scale. Spinodally decomposed interdendritic regions were uniformly distributed in the industrially melted alloy, and a finer dendritic structure with smaller sized spinodal structures was observed in the alloy suction cast at lab scale. The suction cast alloy fabricated at the lab scale exhibited significantly higher compressive yield strength compared to the industrially cast alloy. The relative strengthening contributions in the alloys due to solid solution, grain boundary, dislocation interactions and interphase boundary were analyzed. Dislocation hardening was the major contributor responsible for the higher strength of the SC alloy. The deformation behavior in the alloys was examined with the help of orientation image mapping. Finally, intense slip band formation at large strains in the industrially melted alloy indicates that cold working can be an effective technique to enhance the strength of the dual-phase high entropy alloy processed at a large scale.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Comparison of three state-of-the-art crystal plasticity based deformation twinning models for magnesium alloys

In magnesium alloys, deformation twinning and its interactions with dislocation slip are responsible for a sigmoidal shape stress–strain behavior and an asymmetrical tension–compression yield strength in magnesium alloys. The sensitivity of twinning to the underlying microstructure renders the crystal plasticity method the most commonly adopted modeling approach for magnesium-twinning. This paper compares three state-of-the-art crystal plasticity-based twinning models from the literature, namely the elastic-viscoplastic self-consistent twinning-detwinning (EVPSC-TDT) model, crystal plasticity finite element model based on enhanced predominate twin reorientation approach (CPFE-ePTR), and the crystal plasticity finite element model based on “discrete twinning” approach (CPFE-DT). A polycrystalline microstructure is simulated with all three methods to compare the resulting stress–strain curves and lattice strains to those from the experimentally measured data. All three methods showed the capability of capturing the experimental results with different levels of accuracy. Additionally, the EVPSC-TDT method avoids solving the finite element matrices and showed the highest computational efficiency. The CPFE-ePTR model shows a higher accuracy in capturing the lattice strain. The CPFE-DT relies on high-resolution finite element mesh and is much slower than the other two methods, but it captured the local deformation concentration and stress reversal phenomena near the twin band, which was not possible with the other two methods. Based on the comparison, guidance for the selection of the appropriate model based on the specific modeling target is provided in this paper.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Development of high-early-strength fiber-reinforced self-compacting concrete

High-early-strength fiber-reinforced self-compacting concrete (FRSCC) is a practical material for the precast concrete industry to double its production capacity. In this study, we developed high-early-strength FRSCC mixtures that achieved a compressive and flexural strength of at least 24 MPa and 3.5 MPa, respectively, at 6 h, using commercially available components, typical mixing procedures, and air curing. A mix design process was developed based on the literature and experimental results. The effect of six different fiber reinforcements on the fresh and mechanical properties of concrete was analyzed. The cost limit was set at 523 USD/m 3 to make the concrete mix cost-effective.

36 MATERIALS SCIENCE↗