Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSED GASES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Turbulent thermal convection in a differentially rotating channel

Differentially rotating disks of gases and solids occur in several astrophysical systems, in particular in the inner parts of protostellar nebulae, of which our own solar system is thought to be a relic. The objectives of this paper are to: (1) study localized turbulence in circumstances approximating those found in accretion disks using previously existing expertise in performing direct numerical simulation of turbulent, incompressible channel flows with low Reynolds numbers; (2) determine the limitations of such calculations; and (3) extend the type of numerical simulation (e.g., to include density and stratification and compressibility effects and to accommodate higher Reynolds numbers with sub-grid scale modeling) so that the relevant physical effects are realistically captured.

Cabot, W.↗
NASA NTRS1993

Comparison of the initial development of shear layers in two-dimensional and axisymmetric ejector configurations

A two-phase experimental investigation designed to study the development of shear layers in axisymmetric and two-dimensional single-nozzle ejectors has been completed. In this study, combinations of similar and dissimilar gases were used as the supersonic primary and subsonic secondary. Test cases included combinations of air/air, argon/air and helium/air as the supersonic primary and subsonic secondary, respectively. Similar flow conditions were studied for each ejector configuration. Mixing of the gases occurred in a constant-area tube, where the inlet pressure was maintained at 34.5 kPa. The cases studied resulted in convective Mach numbers that range between 0.06 and 1.9. The data gathered shows differences between the initial shear-layer development for the two ejector geometries, and also between the different test cases studied for each ejector configuration. The measured growth rates for the axisymmetric ejector are more than twice those measured for the two-dimensional ejector. However, in both cases the results show that compressibility has a reducing effect on the growth rate. Further, in the region immediately after the inlet to the mixing tube, compressibility seems to affect the ejector shear layers in a manner similar to that of two-stream two-dimensional mixing layers.

Dufflocq, M.↗
DOE OSTI2024

Neutron-producing gas puff Z-pinch experiments on a fast, low-impedance, 0.5 MA linear transformer driver

A study on the neutron production from single and double gas puff Z-pinches on the CESZAR linear transformer driver with ~0.45 MA current and 170 ns rise time is presented. Total neutron yield measurements made with a LaBr activation detector are compared for three configurations, using a double nozzle setup. When a single, hollow, deuterium gas shell was used, reliable implosions could only be attained at higher load mass than the optimal value to match implosion time with the driver rise time, with neutron yields of ~10 6 per pulse. The use of a double gas puff configuration with a deuterium center jet allowed a reduction in the shell density and operation closer to machine-matched conditions, recording up to (4.1 ± 0.3) × 10 7 neutrons/pulse when either Kr or D 2 was used in the shell. For a comparable mass and implosion time, using a higher atomic-number gas in the outer shell results in more unstable plasma surface and smaller plasma radius at the location of instability bubbles, which, however, do not seem to consistently correlate with a higher neutron yield. Comparing implosion dynamics with models and neutron yields with literature scaling suggests that the machine current is not well coupled to the plasma during the final stages of compression. Optimizing current and energy coupling to the pinched plasma is critical to improving performance, particularly in low-impedance drivers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1973

Supersonic turbulent boundary-layer flows with tangential slot injection.

An implicit finite-difference method has been developed for the solution of the compressible boundary-layer equations. This method is applied to tangential slot injection into supersonic turbulent boundary-layer flows. In addition, the effects induced by the interaction between the boundary-layer displacement thickness and the external pressure field are considered. Three different eddy viscosity models have been used to specify the turbulent momentum exchange. One model depends on the species concentration profile, and the species conservation equation has been included in the system of governing partial differential equations. For air injected into air, the freestream and injected gases are treated as separate species which have common fluid properties. Calculations were made and results were compared with experimental data at freestream Mach numbers of 2.4 and 6.0 and with results of another finite-difference method. Good agreement was obtained for the reduction of wall skin friction with slot injection.

Miner, E. W.↗
DOE OSTI2021

Production, fuel properties and combustion testing of an iso-olefins blendstock for modern vehicles

With the increasing pressure to decarbonize the transportation sector, exploring strategies that can reduce emissions from light-duty vehicles (LDV) has become critical. Bioblendstocks that allow for higher engine efficiency and fuel economy could complement vehicle electrification and help reach carbon neutrality by 2050. In this context, the potential of a mixture of iso-olefins as a bioblendstock was investigated for multimode boosted spark-ignition (SI)/advanced compression ignition (ACI) engine operation designed to achieve higher overall vehicle fuel economy. By establishing the relationship between the molecular structure of iso-olefins and research octane number (RON), octane sensitivity (S) (i.e., the difference between RON and motor octane number [MON]), and phi-sensitivity a dimethyl-hexenes rich olefins mixture (DMHROM) was identified as a preferred blendstock for SI/ACI combustion engines. Here, a pathway for DMHROM production from biomass-derived ethanol was developed and scaled up. More than 1 gallon of DMHROM blendstock was produced for fuel properties assessment including engine testing. Measurements in a Cooperative Fuel Research Engine showed that the DMHROM blendstock possesses a RON of 94 and S of 13.5, and blends synergistically. Rapid compression machine tests coupled with single-cylinder gasoline direct injection engine measurements demonstrated the 20 vol.% DMHROM blend has higher phi-sensitivity than an olefin-free gasoline base fuel and a typical California Reformulated Gasoline Blendstock for Oxygenate Blending (CARBOB) gasoline fuel. These results demonstrate the potential of DMHROM for improving gasoline fuel performance and quality for operation under ACI conditions. The effectiveness of the aftertreatment system in mitigating emissions was verified and showed that the pure DMHROM blendstock and 20 vol.% blend would not increase non-methane organic gases, NO x , and carbon monoxide (CO) emissions. The DMHROM blendstock was found to slightly decrease sooting tendency when added to a gasoline-base fuel (i.e., ~6% reduction at 20 vol.% blending level). Oxidation stability and lubricant compatibility were both confirmed for the 20 vol.% blend. Overall, these results demonstrate that dimethyl-hexenes have potential for improving engine efficiency and fuel economy while meeting emissions regulations and ASTM specifications for gasoline fuel.

09 BIOMASS FUELS↗
NASA NTRS1996

Cardiopulmonary Changes with Moderate Decompression in Rats

Sprague-Dawley rats were compressed to 616 kPa for 120 min then decompressed at 38 kPa/min to assess the cardiovascular and pulmonary responses to moderate decompression stress. In one series of experiments the rats were chronically instrumented with Doppler ultrasonic probes for simultaneous measurement of blood pressure, cardiac output, heart rate, left and right ventricular wall thickening fraction, and venous bubble detection. Data were collected at base-line, throughout the compression/decompression protocol, and for 120 min post decompression. In a second series of experiments the pulmonary responses to the decompression protocol were evaluated in non-instrumented rats. Analyses included blood gases, pleural and bronchoalveolar lavage (BAL) protein and hemoglobin concentration, pulmonary edema, BAL and lung tissue phospholipids, lung compliance, and cell counts. Venous bubbles were directly observed in 90% of the rats where immediate post-decompression autopsy was performed and in 37% using implanted Doppler monitors. Cardiac output, stroke volume, and right ventricular wall thickening fractions were significantly decreased post decompression, whereas systemic vascular resistance was increased suggesting a decrease in venous return. BAL Hb and total protein levels were increased 0 and 60 min post decompression, pleural and plasma levels were unchanged. BAL white blood cells and neutrophil percentages were increased 0 and 60 min post decompression and pulmonary edema was detected. Venous bubbles produced with moderate decompression profiles give detectable cardiovascular and pulmonary responses in the rat.

Robinson, R.↗
DOE OSTI2024

Recovery of Natural Gas Equipment Emissions into Gas Compression Engines for the Reduction of Potential Greenhouse Gas Emissions

Since the turn of the millennium, the United States (U.S.) oil and natural gas (ONG) industry has nearly doubled its natural gas production rate. As a result, the ONG industry has recently come under increasing scrutiny for its contributions to greenhouse gas (GHG) emissions. Consequently, various solutions to this problem have been proposed and formulated to reduce the impacts of GHG emissions on the environment. West Virginia University (WVU) have found it important to research the impacts of recovering vented gas streams into prime-mover engines. The U.S. Department of Energy (DOE) and National Energy Technology Laboratory (NETL) have granted WVU funding to research and develop a “Methane Mitigator” (M2) - a “Scalable Vent Mitigation Strategy to Simultaneously Reduce Methane Emissions and Fuel Consumption from the Compression Industry.” One of the main areas of interest for this research was the collection of emissions from natural gas equipment into a Caterpillar G3508J natural gas compression engine. The parameters being analyzed from the engine were brake-specific emissions and power output. The emissions sources considered for this research were pneumatic controllers (PCs), reciprocating compressor vents, and the engine’s open crankcase breather. The compressor vent and PC emissions were simulated using a mass flow controller (MFC) and flowed into the engine using two separate methods: (1) directly into the air intake, and (2) through a retrofitted closed crankcase ventilation system (CCV), serving as a buffer volume. The crankcase emissions were quantified without the CCV, and the impact on exhaust emissions from circulating the crankcase gases into the intake was measured. The simulated compressor vent and PC flows from the MFC had limited effect on the steady state operation of the engine and resulting performance. When the simulated flows were fed directly into the engine’s air intake, the changes within the engine’s continuous performance and emission parameters were larger but lasted for shorter durations. Conversely, when the simulated flows were fed into the CCV before entering the air intake, the changes in the engine’s performance and emission parameters were less pronounced for continuous analysis but lasted for longer durations. In either case, the continuous emission changes in both emissions and performance varied in size depending on the test scenario being run, but the cycle average changes in emissions and performance showed little impact overall compared to the engine’s baseline operation. As a result, the inclusion of a CCV shows a decrease in baseline carbon dioxide equivalent (CO2-eq.) engine emissions (from combined exhaust and open crankcase) of almost 4%. Likewise, the CCV inclusion reduced baseline total methane (CH4) from combined exhaust and open crankcase by upwards of 16%. These atmospheric emissions only decreased further with the inclusions of collected PC and compressor vent flows. The resulting changes in time-averaged rated exhaust behavior (or lack thereof) prove that the proposed M2 system could likely be deployed at sites with modern lean-burn natural gas engines as a viable option for reducing and eliminating potential GHG sources that would have otherwise been unutilized as energy sources.

03 NATURAL GAS↗
NASA NTRS1980

Pioneer Venus Sounder Probe Neutral Gas Mass Spectrometer

A neutral gas mass spectrometer was flown to Venus as part of the Pioneer Venus Multiprobe to measure the composition of its lower atmosphere. The instrument, mounted in the Sounder Probe, was activated after the probe entered the top of the atmosphere, and it obtained data during the descent from 62 km to the surface. Atmospheric gases were sampled through a pair of microleaks, the effluent from which was pumped by a combination of ion and getter pumping. A pneumatically operated valve, controlled by the ambient atmospheric pressure, maintained the ion source pressure at a nearly constant value during descent while the atmospheric pressure varied by three orders of magnitude. A single focusing magnetic sector field mass spectrometer with mass resolution sufficient to reasonably separate argon from C3H4 at 40 amu provided the mass analysis and relative abundance measurements. A microprocessor controlled the operation of the mass spectrometer through a highly efficient peak-tip stepping routine and data compression algorithm that effected a scan of the mass spectrum from 1 to 208 amu in 64 sec while requiring an information rate of only 40 bits/sec to return the data to earth. A subscale height altitude resolution was thus obtained. Weight, size, and power requirements were minimized to be consistent with interplanetary flight contraints.

Hoffman, J. H.↗
DOE OSTI2025

Two-component atomic Fermi superfluid with spin-orbital coupling in thin-spherical-shell geometry

We present a theory of two-component atomic Fermi superfluid with tunable pairing interaction in a thin spherical shell subject to spin-orbit coupling (SOC). By incorporating SOC into the Fermi superfluid in the BCS-Bose Einstein condensation (BEC) crossover, we obtain the energy spectrum and equations of state. While the order parameter and chemical potential are suppressed by SOC on the BCS side, the former remains positive but the latter may be pushed to negative values by SOC.Meanwhile, the compressibility exhibits kinks as the pairing interaction or SOC varies, indicating singular behavior of higher derivatives of the free energy despite the presence of the superfluid order parameter. The minimum of the energy dispersion indicates a decoupling of the energy gap from the order parameter, and the compressibility kinks occur when the energy gap approaches 0. We found the particle-hole mixing in the Fermi superfluid essential for the compressibility kinks since a Fermi gas with the same SOC but no pairing interaction only exhibits complicated dispersions but no singular behavior. Therefore, our results show that a combination of superfluid, SOC, and geometry can lead to interesting phenomena. Here, we also discuss possible experimental realizations and implications.

Fermi gases↗
NASA NTRS1987

Navier-Stokes simulation of real gas flows in nozzles

Air flow in a hypersonic nozzle causes real gas effects due to reaction among the species constituting air. Such reactions may be in chemical equilibrium or in chemical nonequilibrium. Here using the CSCM upwind scheme for the compressible Navier-Stokes equations, the real gas flowfield in an arcjet nozzle is computed for both the equilibrium case and the nonequilibrium case. A hypersonic nozzle flow arising from a pebble bed heated plenum is also computed for the equilibrium situation. Between the equilibrium cases, the chemistry is treated by two different schemes and comments are made as to computational complexity. For the nonequilibrium case, a full set of seventeen reactions and full implicit coupling of five species with gasdynamics is employed to compute the flowfield. For all cases considered here the gas is assumed to be a calorically imperfect mixture of ideal gases in thermal equilibrium.

Nagaraj, N.↗
DOE OSTI2019

Krypton storage capacity of the Earth's lower mantle

Noble gases are important geochemical tracers allowing reconstructing global volatile cycles in Earth's reservoirs. To constrain these fundamental processes, precise data on their partitioning behavior at deep Earth conditions are needed. Such data are only available at moderate pressures up to 25 GPa due to experimental challenges. We have investigated the possibility of noble gas storage in the Earth's lower mantle up to 115 GPa. We studied the incorporation of krypton in the second most abundant lower mantle mineral (Mg 1-x ,Fe x )O (ferropericlase) as well as in liquid metal-alloys by performing experiments up to 115 GPa and 3700 K using the laser-heated diamond anvil cell coupled to post-mortem EMPA analysis and X-ray absorption spectroscopy. The results reveal that, at these extreme conditions, up to 3 wt.% of krypton can be stored in (Mg 1-x ,Fe x )O and 3000 ppm in the Fe-rich liquid metal. For both phases the storage capacities increase with pressure (between 40 GPa and 60 GPa) at a constant high temperature of 2300 K. Fpc has never been considered as a NG host, despite being the second most abundant mineral in the Earth's LM. Using recent accurate compressibility data, we demonstrate that a substitution of krypton into the anion site of (Mg 1-x ,Fe x )O in form of neutral oxygen Schottky defects at diluted lower mantle conditions is possible. This noble gas incorporation mechanism is in agreement with a previous study on bridgmanite. We show that (Mg 1-x ,Fe x )O exhibits higher noble gas storage capacities than bridgmanite through the lower mantle using lattice strain modeling and including experimental solubility and thermoelastic data for neon, argon, krypton and xenon. We also demonstrate that both phases exhibit the highest solubilities for argon and krypton. We used the solubility data from lattice strain modeling to predict noble gas abundances stored in the solid lower mantle after magma ocean crystallization. The modeled abundances show apparent similarities with estimates for the deep noble gas reservoir that are based on either 3He abundances in ocean island basalts or radiogenic 40Ar abundances in the bulk Earth. This strongly indicates that the crystalline lower mantle may play an important role as deep noble gas storage reservoir. We propose, based on considerations on noble gas replenishment from the lower mantle to the atmosphere, that the lower mantle can only contribute to a small fraction of the present-day atmospheric noble gases. This suggests that the lower mantle is an un-degassed reservoir.

58 GEOSCIENCES↗
DOE OSTI2023

Synchrotron radiography of Richtmyer–Meshkov instability driven by exploding wire arrays

We present a new technique for the investigation of shock-driven hydrodynamic phenomena in gases, liquids, and solids in arbitrary geometries. The technique consists of a pulsed power-driven resistive wire array explosion in combination with multi-MHz synchrotron radiography. Compared to commonly used techniques, it offers multiple advantages: (1) the shockwave geometry can be shaped to the requirements of the experiment, (2) the pressure (P > 300 MPa) generated by the exploding wires enables the use of liquid and solid hydrodynamic targets with well-characterized initial conditions (ICs), (3) the multi-MHz radiography enables data acquisition to occur within a single experiment, eliminating uncertainties regarding repeatability of the ICs and subsequent dynamics, and (4) the radiographic measurements enable estimation of compression ratios from the x-ray attenuation. In addition, the use of a synchrotron x-ray source allows the hydrodynamic samples to be volumetrically characterized at a high spatial resolution with synchrotron-based microtomography. This experimental technique is demonstrated by performing a planar Richtmyer–Meshkov instability (RMI) experiment on an aerogel–water interface characterized by Atwood number A0∼−0.8 and Mach number M∼1.5. The qualitative and quantitative features of the experiment are discussed, including the energy deposition into the exploding wires, shockwave generation, compression of the interface, startup phase of the instability, and asymptotic growth consistent with Richtmyer's impulsive theory. Additional effects unique to liquids and solids—such as cavitation bubbles caused by rarefaction flows or initial jetting due to small perturbations—are observed. It is also demonstrated that the technique is not shape dependent by driving a cylindrically convergent RMI experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Transformational Sorbent-Based Process for a Substantial Reduction in the Cost of CO2 Capture

Adsorption processes have the potential to significantly reduce the CO2 capture cost from power plants and industrial flue gases. InnoSepra has developed several sorbent-based technologies to obtain very high CO2 recovery and high purity CO2 while meeting the EOR/sequestration product specifications. A first-generation process was shown to achieve CO2 recoveries greater than 94% at CO2 purities in the range of 98.5-99.5%. The absolute heat energy required for the process was not only 40% lower than MEA but also was needed at a much lower temperature. This work will present the performance of the second-generation InnoSepra process which is based on a breakthrough sorbent regeneration method. This process has a projected 45% lower capital cost compared to MEA, less than 16% loss in plant output for CO2 capture and compression, and a CO2 capture cost at least 55% lower than MEA. Lab scale testing and the process simulations indicate a CO2 capture performance similar to or better than the first-generation process. Pilot scale drying and breakthrough tests were carried out at the Technology Centre Mongstad (TCM), Norway, and lab-scale cyclic tests were carried out at InnoSepra to confirm the process improvement. During these tests, InnoSepra’s flue gas purification technology was also tested at TCM. It can provide a low-cost option for the removal of NO2 and SOX to sub-ppm levels as well as a significant reduction in aerosol emissions.

08 HYDROGEN↗
NASA NTRS1996

Computation of Thermally Perfect Compressible Flow Properties

A set of compressible flow relations for a thermally perfect, calorically imperfect gas are derived for a value of c(sub p) (specific heat at constant pressure) expressed as a polynomial function of temperature and developed into a computer program, referred to as the Thermally Perfect Gas (TPG) code. The code is available free from the NASA Langley Software Server at URL http://www.larc.nasa.gov/LSS. The code produces tables of compressible flow properties similar to those found in NACA Report 1135. Unlike the NACA Report 1135 tables which are valid only in the calorically perfect temperature regime the TPG code results are also valid in the thermally perfect, calorically imperfect temperature regime, giving the TPG code a considerably larger range of temperature application. Accuracy of the TPG code in the calorically perfect and in the thermally perfect, calorically imperfect temperature regimes are verified by comparisons with the methods of NACA Report 1135. The advantages of the TPG code compared to the thermally perfect, calorically imperfect method of NACA Report 1135 are its applicability to any type of gas (monatomic, diatomic, triatomic, or polyatomic) or any specified mixture of gases, ease-of-use, and tabulated results.

Witte, David W.↗
DOE OSTI2021

Effect of nitric oxide and exhaust gases on gasoline surrogate autoignition: iso-octane experiments and modeling

Exhaust gas recirculation (EGR) is widely used in advanced internal combustion engines to reduce engine emissions as well as control combustion phasing. Among various species present in EGR gases, CO 2 and H 2 O are two major components that can thermally and chemically affect fuel autoignition. It is of fundamental interest to isolate the thermal and chemical effects of CO 2 and H 2 O on fuel autoignition, especially as such an effort has not been reported in the literature. Moreover, nitric oxide (NO) is known to exhibit strong chemical effects on fuel autoignition, which in turn affects engine combustion phasing. The effects of ultra-low NO addition (< 100 ppm) on fuel autoignition at low temperatures are also not well understood. Recognizing these problems, autoignition experiments of iso-octane (a major gasoline surrogate component) in air are performed in this study using a rapid compression machine at varying compressed pressures, equivalence ratios, dilution levels with an EGR gas analogue (consisting of CO 2 , H 2 O, O 2 , and N 2 ) and N 2 only, and varying amounts of NO addition. Furthermore, the thermal and chemical effects of the EGR gas analogue are isolated and evaluated by comparing the ignition delay time datasets of EGR and N2-only diluted cases.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Comprehensive Cradle to Grave Life Cycle Analysis of On-Road Vehicles in the United States based on GREET

To properly compare and contrast the environmental performance of one vehicle technology against another, it is necessary to consider their production, operation, and end-of-life fates. Since 1995, Argonne’s GREET® life cycle analysis model (Greenhouse gases, Regulated Emissions, and Energy use in Technologies) has been annually updated to model and refine the latest developments in fuels and materials production, as well as vehicle operational and composition characteristics. Updated cradle-to-grave life cycle analysis results from the model’s latest release are described for a wide variety of fuel and powertrain options for U.S. light-duty and medium/heavy-duty vehicles. Light-duty vehicles include a passenger car, sports utility vehicle (SUV), and pick-up truck, while medium/heavy-duty vehicles include a Class 6 pickup-and-delivery truck, Class 8 day-cab (regional) truck, and Class 8 sleeper-cab (long-haul) truck. Powertrain coverage includes internal combustion (spark ignition and compression ignition) engines, hybrid electric, plug-in hybrid, full battery electric, and fuel cell vehicles powered by conventional and low carbon energy sources. The results offer insights into the current state of these technologies, as well as a projection of the likely environmental implications of future fuel and vehicle advancements through a time-series evaluation of life cycle greenhouse gas emissions.

Kelly, Jarod C.↗
NASA NTRS1993

Energetic particle environment in the early solar system - Extremely long pre-compaction meteoritic ages or an enhanced early particle flux

Individual mineral grains from meteorites have been exposed to energetic particles prior to inclusion in the host meteorite matrix, an event which occurred quite early in solar system history. Spallation-produced noble gases in such grains are observed to be orders of magnitude greater in abundance than could be produced after meteorite formation and thus provide a record of precompaction irradiation by energetic particles. If attributed to the contemporary particle environment (current galactic and solar cosmic rays) a minimum exposure time for these grains in the CM parent-body regolith of 150 Myr is obtained, with more realistic models suggesting an active parent body regolith for 300 Myr. Constraints on when meteorite compaction occurred and current models for meteorite evolution suggest that this is unreasonably long, that the time available for exposure to energetic particles on the surface of the parent-body regolith is much less than this. Pre-compaction exposure, compressed into a shorter span of time by constraints on the compaction times of carbonaceous meteorites, would require energetic particle fluxes in excess of those in the contemporary solar system and point toward an active early (T Tauri) sun as its source.

Woolum, Dorothy S.↗
NASA NTRSDate not supplied

Fast Radiative Transfer Model and Retrieval Algorithm Development for Satellite Remote Sensing Applications

The radiative transfer model (RTM) has a wide range of applications in satellite remote sensing and atmospheric radiation studies. For example, it can be used as a forward model for an inversion algorithm and a satellite data assimilation system, or as a L1 data simulator for pre-launch end-to-end satellite sensor performance studies. However, millions of line-by-line (LBL) radiative transfer calculations at fine monochromatic frequencies are needed in order to properly calculate spectral contributions of water vapor and trace gases in the atmosphere in infrared and solar spectral regions. Therefore, fast, and accurate radiative transfer models are needed. A Principal Component-based radiative transfer model (PCRTM) was developed at NASA Langley to fulfil this need. The PCRTM can simulate the top-of-atmosphere (TOA) radiance or reflectance spectra from 250 nm to 2000 micrometers with several orders of magnitude faster speed as compared to a LBL RTM. It is also extremely accurate compared to LBL RTM benchmarks. The PCRTM model has been developed for hyperspectral sensors such as AIRS, CrIS, IASI, NAST-I, SHIS, CPF, TEMPO, EMIT, OMI, and SCIAMACHY. By using the PCRTM as forward model for an inversion algorithm, one can reduce the data dimension significantly while maintaining original information content by compressing the TOA radiance spectrum into PC-scores. The PCRTM can directly compute the PC-scores and their derivatives with respect to retrieved parameters. Examples of using various PCRTM inversion algorithms to retrieve atmospheric temperature, water vapor, and trace gas profiles, as well as cloud and surface properties from satellite hyperspectral remote sensors will be given. Some of the algorithms have been transitioned to NASA's Goddard Earth Sciences Data and Information Services Center (GES DISC) for public access of high-quality L2 and L3 data.

Xu Liu↗