Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Axial Staging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1950

Investigation of Performance of Axial-Flow Compressor of XT-46 Turbine-Propeller Engine. I - Preliminary Investigation at 50-,70-, and 100-Percent Design Equivalent Speed

An investigation is being conducted to determine the performance of the 12-stage axial-flow compressor of the XT-46 turbine-propeller engine. This compressor was designed to produce a pressure ratio of 9 at an adiabatic efficiency of 0.86. The design pressure ratios per stage were considerably greater than any employed in current aircraft gas-turbine engines using this type of compressor. The compressor performance was evaluated at two stations. The station near the entrance section of the combustors indicated a peak pressure ratio of 6.3 at an adiabatic efficiency of 0.63 for a corrected weight flow of 23.1 pounds per second. The other, located one blade-chord downstream of the last stator row, indicated a peak pressure ratio of 6.97 at an adiabatic efficiency of 0.81 for a corrected weight flow of 30.4 pounds per second. The difference in performance obtained at the two stations is attributed to shock waves in the vicinity of the last stator row. These shock waves and the accompanying flow choking, together with interstage circulatory flows, shift the compressor operating curves into the region where surge would normally occur. The inability of the compressor to meet design pressure ratio is probably due to boundary-layer buildup in the last stages, which cause axial velocities greater than design values that, in turn, adversely affect the angles of attack and turning angles in these blade rows.

John W R Creagh↗
NASA NTRS1977

Effect of casing treatment of overall performance of axial-flow transonic fan stage with pressure ratio of 1.75 and tip solidity of 1.5

The effect of a number of casing treatments on the overall performance of a 1.75-pressure-ratio, 423-m/sec-tip-speed fan stage was evaluated. The skewed slot configuration with short-open slots over the midportion of the rotor had a stall margin of 23.5 percent, while the solid casing had a stall margin of 15.0 percent. The skewed slot configuration with long open slots extending ahead of and over portion of rotor displaced the stall line to the lowest flow at all speeds tested. At design speed, the peak efficiency for the long, forward open slots was 1 point less than that for the short midopen slots and 3 points less than that for the solid casing.

Osborn, W. M.↗
NASA NTRS1951

Effect of Angle of Incidence of Second-Stage Vane Assembly on Third-Stage Compressor-Blade Vibration and Engine Performance

Strain-gages were used to measure blade vibrations causing failures in the third stage of a production 11-stage axial-flow compressor. After the serious third-stage vibration was detected, a series of investigations were conducted with second-stage vane assemblies of varying angles of incidence. Curves presented herein show the effect of varying the angle of incidence of second-stage vane assembly on third-stage rotor-blade vibration amplitude and engine performance. A minimum vibration amplitude was obtained without greatly affecting the engine performance with a second-stage vane assembly of 9deg. greater angle of incidence than the assembly normally furnished with the engine.

Meyer, Andre J., Jr.↗
NASA NTRS1996

Dimension Determination of Precursive Stall Events in a Single Stage High Speed Compressor

This paper presents a study of the dynamics for a single-stage, axial-flow, high speed compressor core, specifically, the NASA Lewis rotor stage 37. Due to the overall blading design for this advanced core compressor, each stage has considerable tip loading and higher speed than most compressor designs, thus, the compressor operates closer to the stall margin. The onset of rotating stall is explained as bifurcations in the dynamics of axial compressors. Data taken from the compressor during a rotating stall event is analyzed. Through the use of a box-assisted correlation dimension methodology, the attractor dimension is determined during the bifurcations leading to rotating stall. The intent of this study is to examine the behavior of precursive stall events so as to predict the entrance into rotating stall. This information may provide a better means to identify, avoid or control the undesirable event of rotating stall formation in high speed compressor cores.

Bright, Michelle M.↗
NASA NTRS1999

Inlet Flow Distortion and Unsteady Blade Response in a Transonic Axial-Compressor Rotor

This paper describes the unsteady blade surface pressures on the first-stage rotor blades of a two-stage transonic axial flow compressor experiencing inlet flow distortion. This study was conducted to demonstrate the ability of a full annulus unsteady Reynolds-averaged Navier-Stokes numerical technique to predict unsteady pressures on the rotor blades operating in a distorted inflow. A total pressure distortion produced by a variable mesh screen mounted near the inlet was used to excite the unsteady blade loading on the rotor. On-blade pressure transducers were used to measure the unsteady blade surface pressure. These pressures and the resulting transient load on the rotor blades were compared to the numerical prediction. It is important to develop numerical techniques to predict these transient loads to better understand the response of compressor blades to forcing functions. With this enhanced understanding and ability to predict these transient forces, more robust compressors can be developed. In the study, a high definition of the inlet flow distortion was achieved by rotating the distortion screens. In this manner the inlet flow distortion and the distortion at the first stage stator leading edge were measured at approximately every 0.7 degrees. This full annulus high definition of the inlet flow distortion was used as the inlet boundary condition for the numerical technique. The experimental measurements and numerical analyses are highly complementary in this study. Detailed comparisons between the measurements and the numerical analyses indicate that the current numerical procedure calculates the unsteady aerodynamic pressure on the blade surfaces reasonably well. Further, the agreement of the measured and predicted rotor exit flow distortion at the first stage stator leading edge provides verification of the numerical technique.

Rabe, D. C.↗
NASA NTRS1980

Conceptual design study of an improved gas turbine powertrain

The conceptual design for an improved gas turbine (IGT) powertrain and vehicle was investigated. Cycle parameters, rotor systems, and component technology were reviewed and a dual rotor gas turbine concept was selected and optimized for best vehicle fuel economy. The engine had a two stage centrifugal compressor with a design pressure ratio of 5.28, two axial turbine stages with advanced high temperature alloy integral wheels, variable power turbine nozzle for turbine temperature and output torque control, catalytic combustor, and annular ceramic recuperator. The engine was rated at 54.81 kW, using water injection on hot days to maintain vehicle acceleration. The estimated vehicle fuel economy was 11.9 km/l in the combined driving cycle, 43 percent over the 1976 compact automobile. The estimated IGT production vehicle selling price was 10 percent over the comparable piston engine vehicle, but the improved fuel economy and reduced maintenance and repair resulted in a 9 percent reduction in life cycle cost.

Chapman, W. I.↗
NASA NTRS1989

Turbine stage aerodynamics and heat transfer prediction

A numerical study of the aerodynamic and thermal environment associated with axial turbine stages is presented. Computations were performed using a modification of the unsteady NASA Ames viscous code, ROTOR1, and an improved version of the NASA Lewis steady inviscid cascade system MERIDL-TSONIC coupled with boundary layer codes BLAYER and STAN5. Two different turbine stages were analyzed: the first stage of the United Technologies Research Center Large Scale Rotating Rig (LSRR) and the first stage of the Space Shuttle Main Engine (SSME) high pressure fuel turbopump turbine. The time-averaged airfoil midspan pressure and heat transfer profiles were predicted for numerous thermal boundary conditions including adiabatic wall, prescribed surface temperature, and prescribed heat flux. Computed solutions are compared with each other and with experimental data in the case of the LSRR calculations. Modified ROTOR1 predictions of unsteady pressure envelopes and instantaneous contour plots are also presented for the SSME geometry. Relative merits of the two computational approaches are discussed.

Griffin, Lisa W.↗
NASA NTRS1952

Preliminary Investigation of Flow Fluctuations During Surge and Blade Row Stall in Axial-flow Compressors / c Merle C. Huppert

A preliminary investigation of the flow fluctuations of surge and blade row stall was conducted with three single-stage axial-flow compressors with hub-tip ratios of 0.9,0.8, and 0.5 and with a multistage axial-flow compressor. Flow fluctuations of large amplitude associated with stall were detected in all compressors investigated. The fluctuations were caused by low flow regions affecting 25 to 40 percent of the annulus area and propagating in the direction of compressor rotation, but at a lower speed. Mild audible surge was obtained with the single-stage compressors with hub-tip ratios of 0.9 and 0.8. No audible surge was detected with the 0.5 hub-tip ratio stage. A severe audible surge was obtained with the multistage axial-flow compressor. The surge point was coincident with the sharp drop in pressure ratio due to stall.

ENGINES, TURBO-JET↗