Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Design/Analysis of Metal/Composite Bonded Joints for Survivability at Cryogenic Temperatures

A major design and analysis challenge for the JWST ISM structure is the metal/composite bonded joints that will be required to survive down to an operational ultra-low temperature of 30K (-405 F). The initial and current baseline design for the plug-type joint consists of a titanium thin walled fitting (1-3mm thick) bonded to the interior surface of an M555/954-6 composite truss square tube with an axially stiff biased lay-up. Metallic fittings are required at various nodes of the truss structure to accommodate instrument and lift-point bolted interfaces. Analytical experience and design work done on metal/composite bonded joints at temperatures below liquid nitrogen are limited and important analysis tools, material properties, and failure criteria for composites at cryogenic temperatures are virtually nonexistent. Increasing the challenge is the difficulty in testing for these required tools and parameters at 30K. A preliminary finite element analysis shows that failure due to CTE mismatch between the biased composite and titanium or aluminum is likely. Failure is less likely with Invar, however an initial mass estimate of Invar fittings demonstrates that Invar is not an automatic alternative. In order to gain confidence in analyzing and designing the ISM joints, a comprehensive joint development testing program has been planned and is currently running. The test program is designed for the correlation of the analysis methodology, including tuning finite element model parameters, and developing a composite failure criterion for the effect of multi-axial composite stresses on the strength of a bonded joint at 30K. The testing program will also consider stress mitigation using compliant composite layers and potential strength degradation due to multiple thermal cycles. Not only will the finite element analysis be correlated to the test data, but the FEA will be used to guide the design of the test. The first phase of the test program has been completed and the preliminary analysis has been revisited based on the test data In this work, we present an overview of the test plan, results today, and resulting design improvements.

Bartoszyk, Andrew E.↗

Turbulent Axial Odometer Model

A Galilean-invariant field equation is proposed and tested on standard turbulence model test cases. The field equation provides an additional non-dimensional outer scale which allows the turbulence models to reproduce the axial normal stress increase with Re seen in high Reynolds numbers experiments. The field equation provides a Reynolds number for every point based on the length of turbulent flow upstream of that point in the domain. This outer scale equation can be considered an odometer that gives a length scale conjectured to be related to the large stream wise structures that are seen in turbulent flow and that require run length to develop. A new RANS model using this additional scale is able to match the Reynolds number variation of the normal stresses seen at high Reynolds number. Furthermore, the good attached flow prediction capabilities of current RANS models appears to be attained. Using this scale equation, the entire Reynolds-stress state appears to be predicted correctly, over a large run length Reynolds number range such as experienced in aircraft design.

Olsen, Michael E.↗

Turbulent Axial Odometer Model

A Galilean-invariant field equation is proposed and tested on standard turbulence model test cases. The field equation provides an additional non-dimensional outer scale which allows the turbulence models to reproduce the axial normal stress increase with Re seen in high Reynolds numbers experiments. The field equation provides a Reynolds number for every point based on the length of turbulent flow upstream of that point in the domain. This outer scale equation can be considered an odometer that gives a length scale conjectured to be related to the large streamwise structures that are seen in turbulent flow and that require run length to develop. A new RANS model using this additional scale is able to match the Reynolds number variation of the normal stresses seen at high Reynolds number. Furthermore, the good attached flow prediction capabilities of current RANS models appears to be attained. Using this scale equation, the entire Reynolds-stress state appears to be predicted correctly, over a large run length Reynolds number range such as experienced in aircraft design.

Olsen, Michael E.↗

In-pile investigation results of re-sintering for uranium dioxide fuel with large grain size at temperature 650-700 C

When determining the radiation creep of nuclear fuel, apart from deformation caused by axial compressive stress, there is a shrinkage process induced by radiation re-sintering, which may contribute in total value of in-pile deformation. The aim of this work was to study re-sintering for large grain size fuel of uranium dioxide. WWER fuel pellets with grain size greater than 25 μm have been piled up in a special device and irradiated in the channel number 7 of the RBT-6 pool-type reactor. The height of the fuel column was continuously measured during the irradiation. The average temperature value in the fuel column center was 682 Celsius degrees and the total time of irradiation reached 1800 hours which corresponds to a specific burnup of 2.5 MWd/KgU, taking into account fission density and initial fuel stoichiometry. The results show that re-sintering throughout the height equals to 0.08% which correlates well with thermal re-sintering test and does not have an impact on the steady-state creep rate.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A cylindrical shell with a stress-free end which contains an axial part-through or through crack

The interaction problem of a through or a part through crack with a stress free boundary in a semi-infinite cylindrical shell is considered. It is assumed that the crack lies in a meridional plane which is a plane of symmetry with respect to the external loads as well as the geometry. The circular boundary of the semi-infinite cylinder is assumed to be stress free. By using a transverse shear theory the problem is formulated in terms of a system of singular integral equations. The line spring model is used to treat the part through crack problem. In the case of a through crack the interaction between the perturbed stress fields due to the crack and the free boundary is quite strong and there is a considerable increase in the stress intensity factors caused by the interaction. On the other hand in the problem of a surface crack the interaction appears to be much weaker and consequently the magnification in the stress intensity factors is much less significant.

Erdogan, F.↗

A cylindrical shell with a stress-free end which contains an axial part-through or through crack

The interaction problem of a through or a part through crack with a stress free boundary in a semi-infinite cylindrical shell is considered. It is assumed that the crack lies in a meridional plane which is a plane of symmetry with respect to the external loads as well as the geometry. The circular boundary of the semi-infinite cylinder is assumed to be stress free. By using a transverse shear theory the problem is formulated in terms of a system of singular integral equations. The line spring model is used to treat the part through crack problem. In the case of a through crack the interaction between the perturbed stress fields due to the crack and the free boundary is quite strong and there is a considerable increase in the stress intensity factors caused by the interaction. On the other hand in the problem of a surface crack the interaction appears to be much weaker and consequently the magnification in the stress intensity factors is much less significant.

Erdogan, F.↗

NASTRAN buckling study of a linear induction motor reaction rail

NASTRAN was used to study problems associated with the installation of a linear induction motor reaction rail test track. Specific problems studied include determination of the critical axial compressive buckling stress and establishment of the lateral stiffness of the reaction rail under combined loads. NASTRAN results were compared with experimentally obtained values and satisfactory agreement was obtained. The reaction rail was found to buckle at an axial compressive stress of 11,400 pounds per square inch. The results of this investigation were used to select procedures for installation of the reaction rail.

Williams, J. G.↗

Applicability of discrete element method with spherical and clumped particles for constitutive study of granular materials

Discrete element method (DEM) has been intensively used to study the constitutive behaviour of granular materials. However, to what extent a real granular material can be reproduced by virtual DEM simulations remains unclear. This study attempts to answer this question by comparing DEM simulations with typical features of experimental granular materials. Three groups of models with spherical and clumped particles are investigated from four perspectives: (i) deviatoric stress and volumetric behaviour; (ii) critical state behaviour; (iii) stress-dilatancy relationship; and (iv) the evolution of principal stress ratio against axial strain. The results demonstrate that DEM with spherical or clumped particles is capable of qualitatively describing macroscopic deviatoric stress responses, volumetric behaviour, and critical state behaviour observed in experiments for granular materials. On the other hand, some qualitative deviations between experiments and the investigated DEM simulations are also observed, in terms of the stress-dilatancy behaviour and principal stress ratio against axial strain, which are proven to be critical for constitutive modelling. The results demonstrate that DEM with spherical or clumped particles may not necessarily fully capture experimental features of granular materials even from a qualitative perspective. It is thus encouraged to thoroughly validate DEM with experiments when developing constitutive models based on DEM observations.

58 GEOSCIENCES↗

Measurement of the forming limit stress curve using a multi-axial tube expansion test with a digital image correlation system

A servo-controlled tension-internal pressure testing machine with an optical 3D deformation analysis system (ARAMIS) was used to measure the multi-axial plastic deformation behavior of a high-strength steel sheet for a range of strain from initial yield to fracture. The testing machine is capable of applying arbitrary principal stress or strain paths to a tubular specimen using an electrical, closed-loop servo-control system for axial force and internal pressure. Tubular specimens with an inner diameter of 44.6 mm were fabricated from a high-strength steel sheet with a tensile strength of 590 MPa and a thickness of 1.2 mm by roller bending and laser welding. Several linear and non-linear stress paths in the first quadrant of the stress space were applied to the tubular specimens in order to measure the forming limit curve (FLC) and forming limit stress curve (FLSC) of the as-received test material, in addition to the contours of plastic work and the directions of plastic strain rates. The contours of plastic work and the directions of plastic strain rates measured for the linear stress path experiments were compared with those calculated using selected yield functions in order to identify the most appropriate yield function for the test material. Moreover, a Marciniak-Kuczyński type (M-K) forming limit analysis was performed using the most appropriate yield function. The calculated and measured FLC and FLSC were compared in order to validate the M-K approach. The path-dependence of the FLC and FLSC was also investigated.

97 MATHEMATICS AND COMPUTING↗

Hermeticity of SiC/SiC composite and monolithic SiC tubes irradiated under radial high-heat flux

Demonstration of hermetic SiC fiber–reinforced SiC matrix composite cladding under normal operating environments has been identified as one of the most critical feasibility issues for accident-tolerant fuel cladding in light-water reactors. This study provides critical experimental data needed for understanding the effects of irradiation on hermeticity. SiC composite and monolithic tubes were neutron-irradiated to 2 displacements per atom with and without a nominal radial heat flux of 0.6 MW/m2 to produce a simulated in-pile stress state for the normal operation of a light-water reactor. The through-thickness temperature gradient under irradiation results in a gradient in swelling, which causes a significant stress buildup. Such irradiation-induced stress was modeled using a commercial finite element analysis code. The radial heat flux–irradiation synergism was experimentally investigated by constructing a special irradiation capsule and evaluating the helium hermeticity of the specimens. The simulated stress state exhibited a near equi-biaxial tensile axial and hoop stress of ~150 MPa at the inner surface of the SiC composite tube. This stress level is potentially beyond the matrix cracking stress. Degradation of hermeticity of the SiC composite tubes was observed after irradiation, indicating irradiation-induced cracking, whereas the irradiated monolithic SiC tubes remained hermetic. In conclusion, the results indicate that loss of hermeticity caused by radiation-induced microcracking is a potential issue for SiC composite cladding, depending on the magnitude of the temperature gradients. Coating the outer surface of the cladding was identified as a mitigation strategy that might overcome the cracking issue.

36 MATERIALS SCIENCE↗

Axisymmetric deformations and stresses of unsymmetrically laminated composite cylinders in axial compression with thermally-induced preloading effects

This report documents an analytical study of the response of unsymmetrically laminated cylinders subjected to thermally-induced preloading effects and compressive axial load. Closed-form solutions are obtained for the displacements and intralaminar stresses and recursive relations for the interlaminar shear stress were obtained using the closed-form intralaminar stress solutions. For the cylinder geometries and stacking sequence examples analyzed, several important and as yet undocumented effects of including thermally-induced preloading in the analysis are observed. It should be noted that this work is easily extended to include uniform internal and/or external pressure loadings and the application of strain and stress failure theories.

Paraska, Peter J.↗

A thick-walled cylinder with an axisymmetric internal or edge crack

The paper considers the elastostatic axisymmetric problem for a long thick-walled cylinder containing a ring-shaped internal or edge crack. Using the standard transform technique the problem is formulated in terms of an integral equation which has a simple Cauchy kernel for the internal crack and a generalized Cauchy kernel for the edge crack as the dominant part. As examples the uniform axial load and the steady-state thermal stress problems have been solved and the related stress-intensity factors have been calculated. Among other findings the results show that in the cylinder under uniform axial stress containing an internal crack the stress-intensity factor at the inner tip is always greater than that at the outer tip for equal net ligament thicknesses and in the cylinder with an edge crack which is under a state of thermal stress the stress-intensity factor is a decreasing function of the crack depth, tending to zero as the crack depth approaches the wall thickness.

Erdol, R.↗

Experimental Plan for NBG-18 Graphite Bi-axial Strength Testing in the Second and Third Stress Quadrants

The plan for test system's shake down and eventual (funding permitting) bi-axial testing of grade NBG-18 graphite in the second and third stress quadrant are reported. Testing in the first and fourth stress quadrants was previously reported. Details of the specimen and test system design are given along with the anticipated stress ratios to be tested, including specimen numbers are reported. The estimated test pressures needed to attain the planned stress ratios are reported.

36 MATERIALS SCIENCE↗