Results for “voltage estimation” — Page 12

NASA NTRS1974

A method for the measurement and the statistical analysis of atmospheric turbulence

The instantaneous values of output voltages representing the wind velocity vector and the temperature at different elevations of the 250-foot meteorological tower located at NASA Wallops Flight Center are provided with the three dimensional split-film TSI Model 1080 anemometer system. The output voltages are sampled at a rate of one every 5 milliseconds, digitized and stored on digital magnetic tapes for a time period of approximately 40 minutes, with the use of a specially designed data acqusition system. A new calibration procedure permits the conversion of the digital voltages to the respective values of the temperature and the velocity components in a Cartesian coordinate system connected with the TSI probe with considerable accuracy. Power, cross, coincidence and quadrature spectra of the wind components and the temperature are obtained with the use of the fast Fourier transform. The cosine taper data window and ensemble and frequency smoothing techniques are used to provide smooth estimates of the spectral functions.

Tieleman, H. W.↗

NASA NTRS1982

Turbulence measurements in a confined jet using a six-orientation hot-wire probe technique

The six-orientation hot-wire technique is applied to nonreacting axisymmetric flowfields, obtaining measurements of time-mean and rms voltages at six different orientations, thus providing enough information to determine the time-mean velocities, turbulence intensities, and shear stresses. At each location in the flow, there are six different values of each of the above quantities that can be obtained using six sets of measurements of three adjacent orientations. Flowfield surveys of both swirling and nonswirling confined jets are used to calculate estimates of the mean velocity components and the normal and shear turbulent stresses, and comparisons with independent data are made. A sensitivity analysis of the data reduction technique demonstrates that the largest uncertainties are to be expected in the turbulent shear force estimates.

Janjua, S. I.↗

NASA NTRS1992

The 10 kW power electronics for hydrogen arcjets

A combination of emerging mission considerations such as 'launch on schedule', resource limitations, and the development of higher power spacecraft busses has resulted in renewed interest in high power hydrogen arcjet systems with specific impulses greater than 1000 s for Earth-space orbit transfer and maneuver applications. Solar electric propulsion systems with about 10 kW of power appear to offer payload benefits at acceptable trip times. This work outlines the design and development of 10 kW hydrogen arcjet power electronics and results of arcjet integration testing. The power electronics incorporated a full bridge switching topology similar to that employed in state of the art 5 kW power electronics, and the output filter included an output current averaging inductor with an integral pulse generation winding for arcjet ignition. Phase shifted, pulse width modulation with current mode control was used to regulate the current delivered to arcjet, and a low inductance power stage minimized switching transients. Hybrid power Metal Oxide Semiconductor Field Effect Transistors were used to minimize conduction losses. Switching losses were minimized using a fast response, optically isolated, totem-pole gate drive circuit. The input bus voltage for the unit was 150 V, with a maximum output voltage of 225 V. The switching frequency of 20 kHz was a compromise between mass savings and higher efficiency. Power conversion efficiencies in excess of 0.94 were demonstrated, along with steady state load current regulation of 1 percent. The power electronics were successfully integrated with a 10 kW laboratory hydrogen arcjet, and reliable, nondestructive starts and transitions to steady state operation were demonstrated. The estimated specific mass for a flight packaged unit was 2 kg/kW.

Hamley, John A.↗

NASA NTRSDate not supplied

A Prognostics Framework for Battery Health Monitoring Integrated with Thermal Modeling

Urban Air Mobility (UAM) promises to revolutionize transportation in major cities, offering passenger travel, cargo delivery, and emergency medical services through a network of electric vertical takeoff and landing (eVTOL) aircraft. However, the limited range of current eVTOLs, due to the low specific energy of lithium-ion batteries along with a possibility of thermal runaway conditions poses significant safety concerns, leading to potentially compromising operational safety. To address this critical challenge, researchers are actively evaluating the impact of flight and environmental conditions on onboard lithium-ion battery health. This involves carefully assessing the performance of battery packs under laboratory and operational conditions for developing models to estimate future health using prognostics framework. This study examines the effectiveness of evaluating battery degradation leading to catastrophic failures under varying operational conditions in laboratory. These are captured using physics based models of underlying phenomenons and integrated into the prognostics framework. A fully charged battery undergoes controlled discharge cycles at varying C-rates based on the simulated power draw profile, with current and voltage, temperature data recorded throughout the experiment. The observed data provides valuable insights into how different operating conditions and mission profiles affect battery performance. This information is crucial for developing strategies to optimize battery systems, enhance range, and ultimately ensure the safe and reliable operation of UAM vehicles.

Thermal Modeling↗

NASA NTRSDate not supplied

A Prognostics Framework for Battery Health Monitoring Integrated with Thermal Modeling

Urban Air Mobility (UAM) promises to revolutionize transportation in major cities, offering passenger travel, cargo delivery, and emergency medical services through a network of electric vertical takeoff and landing (eVTOL) aircraft. However, the limited range of current eVTOLs, due to the low specific energy of lithium-ion batteries along with a possibility of thermal runaway conditions poses significant safety concerns, leading to potentially compromising operational safety. To address this critical challenge, researchers are actively evaluating the impact of flight and environmental conditions on onboard lithium-ion battery health. This involves carefully assessing the performance of battery packs under laboratory and operational conditions for developing models to estimate future health using prognostics framework. This study examines the effectiveness of evaluating battery degradation leading to catastrophic failures under varying operational conditions in laboratory. These are captured using physics based models of underlying phenomenons and integrated into the prognostics framework. A fully charged battery undergoes controlled discharge cycles at varying C-rates based on the simulated power draw profile, with current and voltage, temperature data recorded throughout the experiment. The observed data provides valuable insights into how different operating conditions and mission profiles affect battery performance. This information is crucial for developing strategies to optimize battery systems, enhance range, and ultimately ensure the safe and reliable operation of UAM vehicles.

Thermal Modeling↗

NASA NTRSDate not supplied

A Prognostics Framework for Battery Health Monitoring Integrated with Thermal Modeling

Urban Air Mobility (UAM) promises to revolutionize transportation in major cities, offering passenger travel, cargo delivery, and emergency medical services through a network of electric vertical takeoff and landing (eVTOL) aircraft. However, the limited range of current eVTOLs, due to the low specific energy of lithium-ion batteries along with a possibility of thermal runaway conditions poses significant safety concerns, leading to potentially compromising operational safety. To address this critical challenge, researchers are actively evaluating the impact of flight and environmental conditions on onboard lithium-ion battery health. This involves carefully assessing the performance of battery packs under laboratory and operational conditions for developing models to estimate future health using prognostics framework. This study examines the effectiveness of evaluating battery degradation leading to catastrophic failures under varying operational conditions in laboratory. These are captured using physics based models of underlying phenomenons and integrated into the prognostics framework. A fully charged battery undergoes controlled discharge cycles at varying C-rates based on the simulated power draw profile, with current and voltage, temperature data recorded throughout the experiment. The observed data provides valuable insights into how different operating conditions and mission profiles affect battery performance. This information is crucial for developing strategies to optimize battery systems, enhance range, and ultimately ensure the safe and reliable operation of UAM vehicles.

Thermal Modeling↗

NASA NTRSDate not supplied

Mass Inferencing Model Creation and Deployment to the RASSOR Lunar Excavation Robot

The Regolith Advanced Surface Systems Operations Robot (RASSOR) Excavator is a mobile robotic bucket-drum excavator platform with a unique space regolith excavation capability. The Intelligent Capabilities Enhanced RASSOR research project developed functionality for estimating the quantity of regolith mass ingested during RASSOR operation, enhancing RASSOR’s ability to successfully complete In-Situ Resource Utilization (ISRU) missions. To teleoperate or run autonomously, it is crucial for the amount of regolith mass ingested to be available as a system state for efficient operation. For example, during autonomous operation, RASSOR should navigate and move to a processing plant to offload the collected regolith when the drums are full; without knowledge of the total mass in the drums, this type of high-level planning is not possible. Three distinct modeling approaches were employed in developing a mass inferencing approach that could work on RASSOR, none of which require modification to the hardware. All take in system states, such as arm/drum motor positions, velocities, currents, voltages, and robot pose, and output a mass prediction for each set of the robot’s bucket drums. The developed models run in real-time, outputting predictions for the front drum mass, rear drum mass, timestamp of the last prediction, and total drum mass (sum of front and rear) in RASSOR’s drums. Models deployed to the hardware have low error (<7.5% mean error over the mass range, and <2.6% mean error when drums are more than half full) when making predictions in real-time. Our modeling approach can be adapted to use lunar excavation data to create models that are reflective of RASSOR’s dynamics when operating on the lunar surface. The results of this work are promising and show that models can be developed to accurately estimate excavated regolith mass.

Bucket Drum Excavators↗

NASA NTRSDate not supplied

Mass Inferencing Model Creation and Deployment to the RASSOR Lunar Excavation Robot

The Regolith Advanced Surface Systems Operations Robot (RASSOR) Excavator is a mobile robotic bucket-drum excavator platform with a unique space regolith excavation capability. The Intelligent Capabilities Enhanced RASSOR research project developed functionality for estimating the quantity of regolith mass ingested during RASSOR operation, enhancing RASSOR’s ability to successfully complete In-Situ Resource Utilization (ISRU) missions. To teleoperate or run autonomously, it is crucial for the amount of regolith mass ingested to be available as a system state for efficient operation. For example, during autonomous operation, RASSOR should navigate and move to a processing plant to offload the collected regolith when the drums are full; without knowledge of the total mass in the drums, this type of high-level planning is not possible. Three distinct modeling approaches were employed in developing a mass inferencing approach that could work on RASSOR, none of which require modification to the hardware. All take in system states, such as arm/drum motor positions, velocities, currents, voltages, and robot pose, and output a mass prediction for each set of the robot’s bucket drums. The developed models run in real-time, outputting predictions for the front drum mass, rear drum mass, timestamp of the last prediction, and total drum mass (sum of front and rear) in RASSOR’s drums. Models deployed to the hardware have low error (<7.5% mean error over the mass range, and <2.6% mean error when drums are more than half full) when making predictions in real-time. Our modeling approach can be adapted to use lunar excavation data to create models that are reflective of RASSOR’s dynamics when operating on the lunar surface. The results of this work are promising and show that models can be developed to accurately estimate excavated regolith mass.

bucket drum excavators↗

NASA NTRS1979

Solar-induced variations of environment affecting manned space flight and spacecraft operations

Estimates of short and long term solar activity are required for calculating variations in the environment with regard to spacecraft charging, radiation effects, and orbital lifetime. Correlations appear to exist between the time of solar activity and the time of operational anomalies due to electrical discharges when the dielectric surfaces of geosynchronous spacecraft are charged by interaction with the ambient plasma to levels above breakdown voltage. An ability to predict the solar induced variation variability of the plasmas could permit refinement of design criteria. The influence of the radiation on spacecraft materials, systems, and manned operations is summarized. Solar radition effects on the orbital altitude atmospheric density environment and spacecraft lifetimes are also considered.

Johnson, W. G.↗

NASA NTRS1991

A quick accurate model of nozzle backflow

Backflow from nozzles is a major source of contamination on spacecraft. If the craft contains any exposed high voltages, the neutral density produced by the nozzles in the vicinity of the craft needs to be known in order to assess the possibility of Paschen breakdown or the probability of sheath ionization around a region of the craft that collects electrons for the plasma. A model for backflow has been developed for incorporation into the Environment-Power System Analysis Tool (EPSAT) which quickly estimates both the magnitude of the backflow and the species makeup of the flow. By combining the backflow model with the Simons (1972) model for continuum flow it is possible to quickly estimate the density of each species from a nozzle at any position in space. The model requires only a few physical parameters of the nozzle and the gas as inputs and is therefore ideal for engineering applications.

Kuharski, R. A.↗

NASA NTRS2008

NASA Tech Briefs, May 2008

Topics covered inclde: Deployable Wireless Camera Penetrators; Hand-Held Units for Short-Range Wireless Biotelemetry; Wearable Wireless Telemetry System for Implantable BioMEMS Sensors; Electronic Escape Trails for Firefighters; Architecture for a High-to-Medium-Voltage Power Converter; 24-Way Radial Power Combiner/Divider for 31 to 36 GHz; Three-Stage InP Submillimeter-Wave MMIC Amplifier; Fast Electromechanical Switches Based on Carbon Nanotubes; Solid-State High-Temperature Power Cells; Fast Offset Laser Phase-Locking System; Fabricating High-Resolution X-Ray Collimators; Embossed Teflon AF Laminate Membrane Microfluidic Diaphragm Valves; Flipperons for Improved Aerodynamic Performance; System Estimates Radius of Curvature of a Segmented Mirror; Refractory Ceramic Foams for Novel Applications; Self-Deploying Trusses Containing Shape-Memory Polymers; Fuel-Cell Electrolytes Based on Organosilica Hybrid Proton Conductors; Molecules for Fluorescence Detection of Specific Chemicals; Cell-Detection Technique for Automated Patch Clamping; Redesigned Human Metabolic Simulator; Compact, Highly Stable Ion Atomic Clock; LiGa(OTf)(sub 4) as an Electrolyte Salt for Li-Ion Cells; Compact Dielectric-Rod White-Light Delay Lines; Single-Mode WGM Resonators Fabricated by Diamond Turning; Mitigating Photon Jitter in Optical PPM Communication; MACOS Version 3.31; Fiber-Optic Determination of N2, O2, and Fuel Vapor in the Ullage of Liquid-Fuel Tanks; Spiking Neurons for Analysis of Patterns; Symmetric Phase-Only Filtering in Particle-Image Velocimetry; Efficient Coupler for a Bessel Beam Dispersive Element; and Attitude and Translation Control of a Solar Sail Vehicle.

Source record↗

NASA NTRS2010

Chemical sensors using coated or doped carbon nanotube networks

Methods for using modified single wall carbon nanotubes ("SWCNTs") to detect presence and/or concentration of a gas component, such as a halogen (e.g., Cl.sub.2), hydrogen halides (e.g., HCl), a hydrocarbon (e.g., C.sub.nH.sub.2n+2), an alcohol, an aldehyde or a ketone, to which an unmodified SWCNT is substantially non-reactive. In a first embodiment, a connected network of SWCNTs is coated with a selected polymer, such as chlorosulfonated polyethylene, hydroxypropyl cellulose, polystyrene and/or polyvinylalcohol, and change in an electrical parameter or response value (e.g., conductance, current, voltage difference or resistance) of the coated versus uncoated SWCNT networks is analyzed. In a second embodiment, the network is doped with a transition element, such as Pd, Pt, Rh, Ir, Ru, Os and/or Au, and change in an electrical parameter value is again analyzed. The parameter change value depends monotonically, not necessarily linearly, upon concentration of the gas component. Two general algorithms are presented for estimating concentration value(s), or upper or lower concentration bounds on such values, from measured differences of response values.

Li, Jing↗

NASA NTRS2011

Coated or doped carbon nanotube network sensors as affected by environmental parameters

Methods for using modified single wall carbon nanotubes ("SWCNTs") to detect presence and/or concentration of a gas component, such as a halogen (e.g., Cl.sub.2), hydrogen halides (e.g., HCl), a hydrocarbon (e.g., C.sub.nH.sub.2n+2), an alcohol, an aldehyde or a ketone, to which an unmodified SWCNT is substantially non-reactive. In a first embodiment, a connected network of SWCNTs is coated with a selected polymer, such as chlorosulfonated polyethylene, hydroxypropyl cellulose, polystyrene and/or polyvinylalcohol, and change in an electrical parameter or response value (e.g., conductance, current, voltage difference or resistance) of the coated versus uncoated SWCNT networks is analyzed. In a second embodiment, the network is doped with a transition element, such as Pd, Pt, Rh, Ir, Ru, Os and/or Au, and change in an electrical parameter value is again analyzed. The parameter change value depends monotonically, not necessarily linearly, upon concentration of the gas component. Two general algorithms are presented for estimating concentration value(s), or upper or lower concentration bounds on such values, from measured differences of response values.

Li, Jing↗

NASA NTRSDate not supplied

Cruise Propulsion System Thermal Analysis for NASA’s X-57 “Maxwell” Mod II Configuration

The X-57 “Maxwell” is NASA’s flight demonstrator for distributed electric propulsion technologies. The X-57 Mod II configuration is designed to test the electric cruise propulsion system for X-57 and features an electric cruise motor mounted in an integral nacelle on each wing. The electric motors and associated control equipment for X-57 Mod II are air-cooled; therefore, they require adequate cooling airflow to stay within temperature limits in all relevant flight conditions within the operational ambient temperature limits set by the X-57 project. A computational flow analysis was conducted to estimate the internal flow properties of the X-57 Mod II cruise nacelles in three critical flight conditions. These flow properties were then used to determine the boundary conditions for individual component thermal models, which were used to estimate individual component operating temperatures. The results indicated that the low-speed, low-altitude initial takeoff climb during hot day conditions was the sizing condition from a cooling perspective. The analysis found that the cooling flowpaths in the X-57 Mod II cruise nacelles are adequate to provide cooling to all components with the appropriate amount of thermal margin except two of the low-voltage control boards in the cruise motor controller. These components would violate required thermal margins by less than two degrees Celsius in the Project Hot Day reference atmosphere.

Nicholas K Borer↗

NASA NTRS1980

Three dimensional space charge model for large high voltage satellites

High power solar arrays for satellite power systems with dimensions of kilometers, and with tens of kilovolts distributed over their surface face many plasma interaction problems that must be properly anticipated. In most cases, the effects cannot be adequately modeled without detailed knowledge of the plasma sheath structure and space charge effects. Two computer programs were developed to provide fully self consistent plasma sheath models in three dimensions as a result of efforts to model the experimental plasma sheath studies at NASA/JSC. Preliminary results indicate that for the conditions considered, the Child-Langmuir diode theory can provide a useful estimate of the plasma sheath thickness. The limitations of this conclusion are discussed. Some of the models presented exhibit the strong ion focusing observed in the JSC experiments.

Cooks, D.↗

NASA NTRS2003

New Technique of High-Performance Torque Control Developed for Induction Machines

Two forms of high-performance torque control for motor drives have been described in the literature: field orientation control and direct torque control. Field orientation control has been the method of choice for previous NASA electromechanical actuator research efforts with induction motors. Direct torque control has the potential to offer some advantages over field orientation, including ease of implementation and faster response. However, the most common form of direct torque control is not suitable for the highspeed, low-stator-flux linkage induction machines designed for electromechanical actuators with the presently available sample rates of digital control systems (higher sample rates are required). In addition, this form of direct torque control is not suitable for the addition of a high-frequency carrier signal necessary for the "self-sensing" (sensorless) position estimation technique. This technique enables low- and zero-speed position sensorless operation of the machine. Sensorless operation is desirable to reduce the number of necessary feedback signals and transducers, thus improving the reliability and reducing the mass and volume of the system. This research was directed at developing an alternative form of direct torque control known as a "deadbeat," or inverse model, solution. This form uses pulse-width modulation of the voltage applied to the machine, thus reducing the necessary sample and switching frequency for the high-speed NASA motor. In addition, the structure of the deadbeat form allows the addition of the high-frequency carrier signal so that low- and zero-speed sensorless operation is possible. The new deadbeat solution is based on using the stator and rotor flux as state variables. This choice of state variables leads to a simple graphical representation of the solution as the intersection of a constant torque line with a constant stator flux circle. Previous solutions have been expressed only in complex mathematical terms without a method to clearly visualize the solution. The graphical technique allows a more insightful understanding of the operation of the machine under various conditions.

Kenny, Barbara H.↗

NASA NTRS2005

Design Optimization Tool for Synthetic Jet Actuators Using Lumped Element Modeling

The performance specifications of any actuator are quantified in terms of an exhaustive list of parameters such as bandwidth, output control authority, etc. Flow-control applications benefit from a known actuator frequency response function that relates the input voltage to the output property of interest (e.g., maximum velocity, volumetric flow rate, momentum flux, etc.). Clearly, the required performance metrics are application specific, and methods are needed to achieve the optimal design of these devices. Design and optimization studies have been conducted for piezoelectric cantilever-type flow control actuators, but the modeling issues are simpler compared to synthetic jets. Here, lumped element modeling (LEM) is combined with equivalent circuit representations to estimate the nonlinear dynamic response of a synthetic jet as a function of device dimensions, material properties, and external flow conditions. These models provide reasonable agreement between predicted and measured frequency response functions and thus are suitable for use as design tools. In this work, we have developed a Matlab-based design optimization tool for piezoelectric synthetic jet actuators based on the lumped element models mentioned above. Significant improvements were achieved by optimizing the piezoceramic diaphragm dimensions. Synthetic-jet actuators were fabricated and benchtop tested to fully document their behavior and validate a companion optimization effort. It is hoped that the tool developed from this investigation will assist in the design and deployment of these actuators.

Gallas, Quentin↗

NASA NTRSDate not supplied

Mass Inferencing Model Creation and Deployment to the RASSOR Lunar Excavation Robot

The Regolith Advanced Surface Systems Operations Robot (RASSOR) Excavator is a teleoperated mobile robotic platform with a unique space regolith excavation capability. The Intelligent Capabilities Enhanced RASSOR research project developed functionality for inferencing regolith mass ingested during RASSOR operation, enhancing RASSOR’s ability to successfully complete ISRU missions. To teleoperate or run autonomously, it is crucial for the quantity of regolith mass ingested by RASSOR to be available as a system state for efficient operation. For example, during autonomous operation, RASSOR should navigate and move to a processing plant to offload the collected regolith when the drums are full; without knowledge of how much mass is in the drums, this type of high-level planning is not possible. Four distinct modeling approaches were employed in developing a mass inferencing approach that could work on RASSOR. All take in system states, such as arm/drum positions, velocities, currents, voltages, and robot pose, and output a mass prediction for each set of the robot’s bucket drums.1) A neural network model that takes a vector of normalized system states; 2) A model that uses the integrated power consumption of an arm-raise (normalized by velocity); 3) A model that uses average drum current over a variable length interval of the drum disengaged from the surface; and 4) A real-time estimation model that aggregates excavation drum current. The developed models run in real time, outputting predictions for the front and rear drums, timestamp of the last prediction, and total mass in RASSOR’s drums. Further testing is required to validate the arm-raise model (2), though initial tests indicate reasonable performance (<10% mean error) on the hardware. The linear fit of average drum-current model (3) had a front value of r^2=0.99 and a rear value of r^2=0.98 on the validation dataset. This model currently has the best performance on unseen data. The real time model (4) is still in development, though initial results on a small subset of the training data show that it has high accuracy in predicting the increase in mass during excavation. Though work remains to be done with deploying a high-fidelity model to the physical system that makes predictions with error below the desired threshold, the modular architecture for model development allows quick adjustment of parameters to increase model fidelity. This architecture can also be adapted to use lunar excavation data to create models that are reflective of RASSOR’s dynamics when operating on the lunar surface. The results are promising as it has been shown that models can be developed that accurately estimate excavated regolith mass.

rassor↗