Results for “treatment” — Page 12

DOE OSTI2024

Integrated Off-gas System: A Preconceptual Design of an Integrated Off-Gas Treatment System

The U.S. has a vested interest in the advancement of nuclear energy to achieve aggressive net-zero goals, with reprocessing and recycling of used nuclear fuels (UNF) playing a vital role. It will not be possible to meet U.S. regulatory requirements without robust off-gas treatment, so it is crucial to advance treatment technologies to facilitate the design of future reprocessing facilities. For many years, teams of researchers across the U.S. Department of Energy (DOE) National Laboratory complex have been investigating off-gas treatment technologies for the capture and removal of volatile radionuclides (i.e., 85 Kr, Xe, 14 C, and 129 I) and oxides of nitrogen (NO X ) that are produced from reprocessing. These investigations have been focused on developing individual technologies for the capture of Kr, Xe, iodine, and CO 2 . Capture technologies for each constituent were tested independently from one another by utilizing nonradioactive surrogates to simulate simplified off-gas streams. The tests have been relatively small, laboratory-scale experiments of up to approximately 1 L/minute total gas flow rate. To increase the readiness of these technologies for deployment, an integrated test system with a larger-scale capacity is needed to bridge the gap between promising bench scale and fully scalable UNF reprocessing off-gas treatment. This document contains the goals, design basis, functional requirements, preconceptual design, and cost estimates for an integrated off-gas demonstration system for the capture and removal of NO x , Kr, Xe, CO 2 , and iodine at 10× higher throughput than earlier laboratory studies. The order-of-magnitude cost estimate for this system is approximately $\$$886,000. Next phases include conceptual design, detailed design, fabrication, and commissioning.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2026

Process Optimization and Real-Time Control of Synergistic Microalgae Cultivation and Wastewater Treatment (Final Technical Report)

The overarching goal of this work was to accelerate the commercialization of high productivity, mixed community microalgal treatment technologies for the synergistic treatment of wastewater and the production of biofuel feedstocks. This project addressed a critical barrier to the financial viability and energy efficiency of algal wastewater treatment: an inability to design and operate high-rate processes that reliably achieve target effluent qualities, areal productivities, and biochemical compositions (lipid, protein, carbohydrate content) despite fluctuations in wastewater composition, weather, and microbial communities. Key outcomes from this work include an optimized and controlled Advanced Biological Nutrient Recovery (ABNR) design as well as a suite of open-source tools that include a calibrated and validated algae process simulator in QSDsan and a novel low-cost, real-time microbial monitoring tool. These tools can be leveraged by other algal cultivation and wastewater treatment technology developers in future work.

09 BIOMASS FUELS↗

NASA NTRS2016

Cooling Rate Study of Nickel-Rich Material During Thermal Treatment and Quench

To investigate quench cracking that results from water quenching after heat treatment of binary and Ni-rich material, cooling rates of specimens were measured during quenching and hardness post-thermal treatment. For specific applications binary Ni-Ti is customarily thermally treated and quenched to attain desired mechanical properties and hardness. However, one problem emerging from this method is thermal cracking, either during the heat treatment process or during the specimen's application. This can result in material and equipment failure as well as financial losses. The objective of the study is to investigate the internal cooling rate of 60-NiTi during quenching and determine possible factors causing thermal cracking. Cubic (1 in.3) samples of both material were heat treated in air at 1000 deg C for 2 hrs and quenched in room temperature water using two methods: (1) dropped in the water and (2) agitated in the water. Hardness of the two fore-mentioned methods was measured post heat treatment. Results indicate that the quenching method had an effect on cooling rate during quenching but hardness was observed to be essentially the same through the thickness of the samples.

Thermal Crack↗

NASA NTRSDate not supplied

A Fundamental Study of Bifurcation Acoustic Treatment Effects on Aft-Fan Engine Noise

Increasing air traffic and more stringent aircraft noise regulations continue to expand requirements on aircraft noise levels for conventional and unconventional aircraft configurations. A major component of the overall aircraft noise is the sound associated with the propulsion system mounted in the engine nacelle. Acoustic liners mounted in the aircraft engine nacelles provide a significant portion of the current fan noise reduction. However, they must be further optimized if challenging noise reduction goals are to be achieved. One location within the aft bypass duct that may be an excellent candidate for increased attention is the acoustic treatment on the engine bifurcations (i.e., engine pylon and lower bifurcation). This paper presents the continuation of a fundamental study of the effects of bifurcation treatment on simulated aft fan noise and the validation of numerical tools to predict such effects. Five bifurcation configurations (four treated and one hardwall) were fabricated and tested in the NASA Langley Curved Duct Test Rig. Results show that mode scattering may occur due to both the presence of the bifurcation, as well as variable impedance distributions on the bifurcation surface. Future work will also include optimization of bifurcation treatments for testing in the Curved Duct Test Rig. These initial results are promising and this work provides valuable information for further study and improvement of the performance of bifurcation acoustic treatments.

bifurcation effects↗

NASA NTRSDate not supplied

A Fundamental Study of Bifurcation Acoustic Treatment Effects on Aft-Fan Engine Noise

Increasing air traffic and more stringent aircraft noise regulations continue to expand requirements on aircraft noise levels for conventional and unconventional aircraft configurations. A major component of the overall aircraft noise is the sound associated with the propulsion system mounted in the engine nacelle. Acoustic liners mounted in the aircraft engine nacelles provide a significant portion of the current fan noise reduction. However, they must be further optimized if challenging noise reduction goals are to be achieved. One location within the aft bypass duct that may be an excellent candidate for increased attention is the acoustic treatment on the engine bifurcations (i.e., engine pylon and lower bifurcation). This paper presents the continuation of a fundamental study of the effects of bifurcation treatment on simulated aft fan noise and the validation of numerical tools to predict such effects. Five bifurcation configurations (four treated and one hardwall) were fabricated and tested in the NASA Langley Curved Duct Test Rig. Results show that mode scattering may occur due to both the presence of the bifurcation, as well as variable impedance distributions on the bifurcation surface. Future work will also include optimization of bifurcation treatments for testing in the Curved Duct Test Rig. These initial results are promising and this work provides valuable information for further study and improvement of the performance of bifurcation acoustic treatments.

bifurcation effects↗

NASA NTRSDate not supplied

A Fundamental Study of Bifurcation Acoustic Treatment Effects on Aft-Fan Engine Noise

Increasing air traffic and more stringent aircraft noise regulations continue to expand requirements on aircraft noise levels for conventional and unconventional aircraft configurations. A major component of the overall aircraft noise is the sound associated with the propulsion system mounted in the engine nacelle. Acoustic liners mounted in the aircraft engine nacelles provide a significant portion of the current fan noise reduction. However, they must be further optimized if challenging noise reduction goals are to be achieved. One location within the aft bypass duct that may be an excellent candidate for increased attention is the acoustic treatment on the engine bifurcations (i.e., engine pylon and lower bifurcation). This paper presents the continuation of a fundamental study of the effects of bifurcation treatment on simulated aft fan noise and the validation of numerical tools to predict such effects. Five bifurcation configurations (four treated and one hardwall) were fabricated and tested in the NASA Langley Curved Duct Test Rig. Results show that mode scattering may occur due to both the presence of the bifurcation, as well as variable impedance distributions on the bifurcation surface. Future work will also include optimization of bifurcation treatments for testing in the Curved Duct Test Rig. These initial results are promising and this work provides valuable information for further study and improvement of the performance of bifurcation acoustic treatments.

bifurcation effects↗

NASA NTRS2023

Acoustic Results of Over the Rotor and Soft Vane Treatments on the Source Diagnostic Test Model in the NASA Glenn Research Center 9- by 15-foot Low-Speed Wind Tunnel

Two novel fan noise reduction concepts were tested using the Source Diagnostic Test fan stage model in the NASA Glenn 9x15 Low Speed Wind Tunnel. One, referred to as over the rotor treatment, consisted of a number of different casing treatments some of which contained acoustic treatment. The other, known as soft vane, consisted of fan exit guide vanes whose interior volume contained acoustic treatment that was exposed to the vane suction side surface through a perforate.

Aeroacoustics↗

DOE OSTI2020

DEM and MELT In-Can Vitrification Process for Fukushima Daiichi Water Treatment Secondary Waste - 20034

Fukushima Daiichi Nuclear Power Station was severely damaged by a tsunami induced by the earthquake on March 11, 2011. A large amount of water treatment secondary waste has been generated from the purification work of contaminated water that consists of the water flowing into the reactor building. The Mid and Long-Term Road map specifies that solid waste at Fukushima Daiichi Nuclear Power Station should be stored safely and reasonably according to its characteristics. In order to meet this goal, a versatile treatment solution is needed, and the In-Can vitrification seems to be a suitable solution. The DEM and MELT In-Can vitrification process is being developed and qualified in France to treat waste arising from decommissioning and dismantling operations. This qualification is carried out through the consortium of the DEM and MELT project coordinated by CEA which gathers Orano, ECM technologies and Andra. The DEM and MELT In-Can vitrification process is a robust, simple and versatile in situ vitrification process. It is designed for high or intermediate level waste and is compact enough to be implemented in an existing facility or close to the waste to be treated. It is developed to treat liquid and solid waste, to produce a small amount of secondary waste and to minimize investment and operating costs. The DEM and MELT In-Can vitrification process is also developed with a modular design in order to be adapted to nuclear operators needs and requirements. The In-Can melting process has already been developed and fully qualified by the CEA for Alpha liquid waste and can be rated TRL 7 for this scope. The In-Can vitrification technology is considered as a qualified solution that could be applied for the treatment of waste resulting from the D and D work in Fukushima Daiichi Nuclear Power Station. The feasibility evaluation of the DEM and MELT In-Can vitrification process for Fukushima Daiichi water treatment secondary waste is a project led by Orano, CEA and ANADEC. This R and D project is performed by the funds from the Ministry of Economy, Trade and Industry as The Subsidy Program 'Project of Decommissioning and Contaminated Water Management'. This paper presents the first results of this feasibility evaluation, from the scenarios and glass formulation definition to the industrial implementation feasibility. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2021

ZIF‐8 Membrane Permselectivity Modification by Manganese(II) Acetylacetonate Vapor Treatment

Abstract Vapor‐phase treatment of ZIF‐8 membranes with manganese(II) acetylacetonate (Mn(acac) 2 ) allows permselectivity tuning. Propylene/propane selectivity increases from 31 to 210 after the Mn(acac) 2 treatment at 165 °C for 30 min, while selectivities increase from 14.6 to 242 for H 2 /CH 4 , from 2.9 to 38 for CO 2 /CH 4 , from 2.4 to 29 for CO 2 /N 2 , and from 2.9 to 7.5 for O 2 /N 2 , after Mn(acac) 2 treatment at 175 °C for 30 min. Stable equimolar propylene/propane mixture selectivity of 165 at ambient temperature and 4 bar equimolar feed with a propylene flux of 8.3×10 −4 mol m −2 s −1 is established. A control experiment excludes thermal treatment alone causing these changes. XPS analysis reveals the presence of Mn(acac) 2 on the outer surface of the vapor‐treated ZIF‐8 membranes while no other changes are detectable by X‐ray diffraction and infrared spectroscopy.

Hayashi, Mikio↗

DOE OSTI2020

Osteoporosis Treatments Affect Bone Matrix Maturation in a Rat Model of Induced Cortical Remodeling

ABSTRACT To test how osteoporosis drugs affect bone matrix maturation during cortical bone remodeling, 72 pregnant rats were switched from a 0.4% to a 0.01% calcium diet at parturition for a 23‐day lactation period. At weaning, eight dams were sacrificed to establish baseline values, while the remaining dams were returned to 0.4% calcium and treated with vehicle (saline), sodium fluoride (NaF), zoledronic acid (ZA), or sclerostin antibody (Scl‐Ab) for either 7 or 28 days (eight animals per group per time point). Femora were examined by μCT, dynamic histomorphometry, Fourier transform infrared imaging, and three‐point bending of notched specimens. Cortical porosity decreased in all groups from baseline to day 28. Intracortical mineralizing surface (MS/BS) and mineral apposition rate (MAR), as well as the mineral‐to‐matrix ratio were unaffected by treatment, but intracortical crystallinity was increased in the ZA group at day 10 compared with vehicle. Cortical area increased in all groups over 28 days mainly because of an addition of bone at the endocortical surface. Endocortical MS/BS did not vary among the groups, but endocortical MAR was suppressed in the NaF group at day 2 and elevated in the Scl‐Ab group at day 4 compared with vehicle. Endocortical mineral‐to‐matrix ratio was increased at days 5 and 10 following NaF treatment and endocortical crystallinity was increased at day 5 following ZA treatment compared with vehicle. Fracture toughness did not differ among the groups. Thus, the treatments affected matrix maturation more strongly at the endocortical then intracortical envelope. In this model of induced remodeling, the bone formation phase is synchronized at multiple sites, facilitating study of the effects of drugs or other bone‐targeting agents on matrix maturation independent of their effects on the initiation of remodeling. © 2020 The Authors. JBMR Plus published by Wiley Periodicals, Inc. on behalf of American Society for Bone and Mineral Research.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Antibiotic Treatment Prior to Injury Abrogates the Detrimental Effects of LPS in STR/ort Mice Susceptible to Osteoarthritis Development

Post traumatic osteoarthritis (PTOA) is a form of secondary osteoarthritis (OA) that develops in ~50% of cases of severe articular joint injuries and leads to chronic and progressive degradation of articular cartilage and other joint tissues. PTOA progression can be exacerbated by repeated injury and systemic inflammation. Few studies have examined approaches for blunting or slowing down PTOA progression with emphasis on systemic inflammation; most arthritis studies focused on the immune system have been in the context of rheumatoid arthritis. To examine how the gut microbiome affects systemic inflammation during PTOA development, we used a chronic antibiotic treatment regimen starting at weaning for 6 weeks before anterior cruciate ligament (ACL) rupture in STR/ort mice combined with lipopolysaccharide (LPS)-induced systemic inflammation. STR/ort mice develop spontaneous OA as well as a more severe PTOA phenotype than C57Bl/6J mice. By 6 weeks post injury, histological examination showed a more robust cartilage staining in the antibiotic-treated (AB) STR/ort mice than in the untreated STR/ort controls. Furthermore, we also examined the effects of AB treatment on systemic inflammation and found that the effects of LPS administration before injury are also blunted by AB treatment in STR/ort mice. The AB- or AB+LPS-treated STR/ort injured joints more closely resembled the C57Bl/6J VEH OA phenotypes than the vehicle- or LPS-treated STR/ort, suggesting that antibiotic treatment has the potential to slow disease progression and should be further explored therapeutically as prophylactic post injury.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2021

Investigation of GaAs surface treatments for ZnSe growth by molecular beam epitaxy without a buffer layer

Atomically clean and smooth surfaces are critical prerequisite for the epitaxial regrowth of dissimilar semiconductors. Using ZnSe/GaAs as a model system, epitaxial regrowth without a buffer layer after thermal cleaning with various As-fluxes, atomic Ga flux, and atomic hydrogen treatments to the GaAs substrates and the surfaces were investigated in this work via in-situ Auger electron spectroscopy (AES). The ZnSe epilayers grown on the pre-treated GaAs surfaces without a buffer layer were characterized by X-ray diffraction (XRD), photoluminescence (PL) and atomic force microscopy (AFM) to evaluate the effectiveness of the surface treatment methods. It was found that a high quality ZnSe layer can be achieved by atomic hydrogen surface treatment at 300°C without requiring GaAs buffer layer growth, which reveals a path for epitaxy growth avoiding high temperature treatments.

42 ENGINEERING↗

DOE OSTI2023

Plasma treatment on both adhesive tape and adherends for significantly enhanced CFRTP-related adhesive joints

Unlike existing literature that primarily concentrates on either the plasma treatment of adherends alone or solely on adhesive surfaces, this work leverages plasma modification of both adhesive in tape form and adherend surfaces to largely enhance the interfacial bonding between a thermoset-based adhesive tape and carbon-fiber-reinforced thermoplastic polymer (CFRTP) for structural bonding applications. Here, by conducting single lap shear tests on adhesively-bonded AA6061-CFRPPA (carbon-fiber-reinforced polyphthalamide) dissimilar joints, it is shown that the plasma treatment of adherends alone can increase the lap shear strength (LSS) of the joints by approximately 200% compared to non-treated counterparts. An additional plasma treatment of adhesive tape surfaces leads to even higher LSS improvement, reaching up to 315%, due to the formation of a denser crosslinked network of covalent bonds and a reduced area fraction of interfacial voids at the CFRPPA/adhesive interface. The highest plasma-enhanced LSS of the metal-CFRTP dissimilar joints rivals that of metal-metal joints, which is typically stronger than the joints associated with fiber-reinforced polymers. This study is important for achieving strong CFRTP-related structural components bonded using adhesive tape, providing better compatibility with plasma treatment and other joining methods like riveting compared to adhesive paste or liquid.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Chemistry of the interaction between an alkoxysilane-based impregnation treatment and cementitious phases

Chemical compatibility with a wide range of materials is among the features that has driven the use of alkoxysilanes as consolidants in built structures. Such compatibility is particularly important in cementitious materials where the reaction with portlandite may generate C-S-H gel, one of the main hydration phases of OPC. The cementitious matrix is a complex system, however, and the reaction of its many phases with alkoxysilanes, while poorly understood, may determine treatment efficacy. This article describes a detailed study of the individual interactions between an oligomeric alkoxysilane-based impregnation treatment previously shown to interact with the portlandite present in cement paste and the cementitious phases generated in ordinary portland cement hydration. The findings show that both portlandite and C-S-H gel interact with the silicon oligomers in the hydrolysed impregnation treatment to generate a C-S-H gel (in the case of portlandite) and a rise in C-S-H gel mean chain length (MCL). Ettringite is also altered in the presence of alkoxysilanes, transforming to gypsum and AH{sub 3}. Its transformation generates a tetrahedral aluminium that is taken up into a high silicon gel sourced from the treatment to form an amorphous aluminosilicate gel. Monocarboaluminate and katoite also partially decompose in the interaction with the product, whereas gibbsite remains unaffected.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Phyllosilicate mineral dissolution upon alkaline treatment under aerobic and anaerobic conditions

The dissolution of phyllosilicate minerals exposed to high-pH environments has been studied to determine the influence of alkaline treatments and variable redox conditions on clay dissolution and the potential formation of new phases via incongruent dissolution phenomena. The present study focused on the dissolution of phyllosilicate minerals (illite, muscovite, and montmorillonite) under anaerobic and aerobic conditions using comparative solutions (sodium hydroxide and ammonium hydroxide) at similar ionic strength in the presence and absence of oxygen. Our batch data show that there is a rapid decrease in aluminum dissolution (< 240 hrs) and slow increase in silica over time (up to 1440 hrs). This trend was particularly evident for montmorillonite which shows the greatest dissolution for ammonium hydroxide, likely due to intercalation of the polyatomic cation ammonium into the mineral’s expandable layers. When comparing alkaline treatments, the strong base, sodium hydroxide, dissolved more of the mica minerals, illite and muscovite, likely due to ion-pairing between the silicate tetrahedra [SiO4]n- and Na+ cations in solution. In addition, redox conditions affect the systems similarly with treatment, although the sodium hydroxide treatment results in greater variability in solution redox conditions. For all investigated phyllosilicates, the calculated aqueous aluminum and silicon ratios over time are significantly different from the minerals’ stoichiometric ratios. As a result, we conclude that incongruent dissolution occurred and suggest formation of secondary precipitates. Understanding the potential for clay mineral alterations from interaction with alkaline solutions has implications for in situ remediation, mining operations, and waste interactions with the subsurface. This research shows that incongruent dissolution is likely and will lead to secondary precipitation which may have long term physical and chemical impacts in the subsurface.

mineral dissolution, phyllosilicate, alkaline, amm↗

DOE OSTI2022

Optimization-based modeling and economic comparison of membrane distillation configurations for application in shale gas produced water treatment

Membrane distillation (MD) is an emerging membrane technology with great potential for treatment of hypersaline wastewater generated by unconventional (shale) oil and gas reservoirs. However, the low energy efficiency of this technology makes the operating cost of MD systems relatively high, especially in the absence of waste heat. There are several MD configurations with inherent advantages and disadvantages and varying performance. As such, there is a need for thermo-economic optimization of MD systems in a systematic manner to assess their economic performance. Here we present an optimization framework to model and compare the performance of six MD configurations (DCMD, AGMD, PGMD, CGMD, SGMD, and VMD) in continuous recirculation mode for treatment of hypersaline wastewater. The optimization results show that AGMD with small gap size operated at low stream Reynolds number outperforms all other configurations with treatment cost of 4.57 US $/m 3 of feed. However, restricting the system design to more practically relevant operating conditions, such as higher Reynolds number and larger gap size, diminishes the cost superiority of AGMD over other configurations. We also observed that treatment cost using PGMD configuration approaches those of CGMD and DCMD, particularly when modules with small gaps are used.

42 ENGINEERING↗

DOE OSTI2026

Zinc treatment to enhance nickel electrode performance for liquid alkaline water electrolyzers

Raney Ni treatment is introduced to the surface of Ni mesh anode electrodes, enhancing liquid alkaline water electrolyzer performance. The surface of the Ni mesh is alloyed with Zn, deposited by either an aqueous infiltration of Zn salt or direct reaction with Zn foil. The extent of alloying is controlled by a heat treatment step. For both processes, fine porosity and enhanced surface area are obtained after leaching the Zn out of the surface alloy layer. The observed electrode surface structure and performance is quite sensitive to the thermal treatment temperature. The enhanced surface area improves full cell performance by 90 mV for infiltrated Zn treated at 600 °C and by 185 mV for Zn foil reacted at 425 °C (at 2 A cm −2 and 80 °C). In conclusion, the Zn treatment methods produce stable operating performance, exhibiting no decay after 150 h for the infiltrated Zn treated at 600 °C, and a decay rate of 4.6 μV h −1 over 100 h for the Zn foil reacted at 425 °C (at 1 A cm −2 and 80 °C).

LAWE↗

DOE OSTI2021

The Role of Circulating Tumor Cells in Breast Cancer and Implications for Radiation Treatment Decisions

Tumor biomarkers are used routinely in oncology to assign risk categorization, screen and assist in diagnosis of malignancy, allow for prognostication and prediction of outcomes and treatment response, and allow for monitoring of patients after treatment completion. Although tissue-based biomarkers have a long history of use, the emergence of liquid-based biomarkers, including circulating tumor cells (CTCs), may soon revolutionize the management of patients with cancer. Here, we review the discovery of CTCs and their role as prognostic and predictive biomarkers, with an emphasis on breast cancer. We discuss the platforms for CTC enumeration and focus on studies using the only US Food and Drug Administration–approved platform for CTC enumeration (CellSearch). In addition, we examine the role of CTCs in women with metastatic, inflammatory, and nonmetastatic breast cancer, as well as the clinical evidence for their use as a surrogate for radiation treatment response as well as surveillance after treatment. Finally, we conclude by investigating ongoing clinical studies assessing CTCs as radiation response predictors and discuss unanswered questions.

62 RADIOLOGY AND NUCLEAR MEDICINE↗