Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermal fracturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Influences of chemical and thermal environments on delay in a Ti-6Al-4V alloy

Experiments were conducted within the framework of linear fracture mechanics to study the effects of chemical and thermal environments on crack-growth retardation (delay) in mill-annealed Ti-6Al-4V alloy under elemental load spectra. Attention is focused on the influence of hold time at high load on delay in a 3.5 percent NaCl solution at room temperature. It is shown that delay is strongly affected by hold time at high load, where delay is longest if the high-load excursion occurs at high temperature and the subsequent fatigue is at room temperature, and shortest if the temperature profile is reversed. The results suggest that residual stresses ahead of the advancing crack play an important role in delay. The significance of combined load and environment (chemical and thermal) effects in terms of modeling and life prediction procedures is discussed.

Shih, T. T.↗
DOE OSTI2021

Fracture Sustainability in Enhanced Geothermal Systems: Experimental and Modeling Constraints

Enhanced geothermal systems (EGS) offer the potential for a much larger energy source than conventional hydrothermal systems. Hot, low-permeability rocks are prevalent at depth around the world, but the challenge of extracting thermal energy depends on the ability to create and sustain open fracture networks. Laboratory experiments were conducted using a suite of selected rock cores (granite, metasediment, rhyolite ash-flow tuff, and silicified rhyolitic tuff) at relevant pressures (uniaxial loading up to 20.7 MPa and fluid pressures up to 10.3 MPa) and temperatures (150–250 °C) to evaluate the potential impacts of circulating fluids through fractured rock by monitoring changes in fracture aperture, mineralogy, permeability, and fluid chemistry. Because a fluid in disequilibrium with the rocks (deionized water) was used for these experiments, there was net dissolution of the rock sample: this increased with increasing temperature and experiment duration. Thermal-hydrological-mechanical-chemical (THMC) modeling simulations were performed for the rhyolite ash-flow tuff experiment to test the ability to predict the observed changes. These simulations were performed in two steps: a thermal-hydrological-mechanical (THM) simulation to evaluate the effects of compression of the fracture, and a thermal-hydrological-chemical (THC) simulation to evaluate the effects of hydrothermal reactions on the fracture mineralogy, porosity, and permeability. Furthermore, these experiments and simulations point out how differences in rock mineralogy, fluid chemistry, and geomechanical properties influence how long asperity-propped fracture apertures may be sustained. Such core-scale experiments and simulations can be used to predict EGS reservoir behavior on the field scale.

15 GEOTHERMAL ENERGY↗
NASA NTRS1980

The origin of polygonal troughs on the northern plains of Mars

The morphology, distribution, geologic environment and relative age of large-scale polygonal trough systems on Mars are examined. The troughs are steep-walled, flat-floored, sinuous depressions typically 200-800 m wide, 20-120 m deep and spaced 5-10 km apart. The mechanics of formation of tension cracks is reviewed to identify the factors controlling the scale of tension crack systems; special emphasis is placed on thermal cracking in permafrost. It is shown that because of the extremely large scale of the Martian fracture systems, they could not have formed by thermal cracking in permafrost, dessication cracking in sediments or contraction cracking in cooling lava. On the basis of photogeologic evidence and analog studies, it is proposed that polygonal troughs on the northern plains of Mars are grabens.

Pechmann, J. C.↗
NASA NTRS2012

Environmental Barrier Coating (EBC) Durability Modeling; An Overview and Preliminary Analysis

A study outlining a fracture mechanics based model that is being developed to investigate crack growth and spallation of environmental barrier coating (EBC) under thermal cycling conditions is presented. A description of the current plan and a model to estimate thermal residual stresses in the coating and preliminary fracture mechanics concepts for studying crack growth in the coating are also discussed. A road map for modeling life and durability of the EBC and the results of FEA model(s) developed for predicting thermal residual stresses and the cracking behavior of the coating are generated and described. Further initial assessment and preliminary results showed that developing a comprehensive EBC life prediction model incorporating EBC cracking, degradation and spalling mechanism under stress and temperature gradients typically seen in turbine components is difficult. This is basically due to mismatch in thermal expansion difference between sub-layers of EBC as well as between EBC and substrate, diffusion of moisture and oxygen though the coating, and densification of the coating during operating conditions as well as due to foreign object damage, the EBC can also crack and spall from the substrate causing oxidation and recession and reducing the design life of the EBC coated substrate.

Abdul-Aziz, A.↗
DOE OSTI2020

Revisiting the first Sandia Fracture Challenge with transient deformation heating and strain localization considerations

In this study, we present a systematic experimental study and accompanying theoretical analysis of the dependence of ductile fracture on strain localization, strain hardening rates, deformation-induced thermal softening, and transient heat conduction under spatially uniform as well as spatially heterogeneous deformation. Spatially uniform cases are studied via standard dogbone shaped specimens subject to uniaxial tension. Spatially heterogeneous deformation is studied via the so-called Sandia Fracture Challenge (SFC) specimen, which is a standard compact tension specimen modified with three machined holes in front of a blunt notch. We utilize the same precipitation hardened martensitic stainless steel used in the first SFC experiments, i.e. 15-5 PH with an H1075 heat treatment. We also study 15-5 PH in Condition A and with the H900 heat treatment, each of which has a different hardening behavior and ductility. We find that the ductility does not correlate with the deformation to first crack initiation in the SFC specimen. Instead, hardening rates are better correlated. Moreover, a re-examination finds that an accurate calibration of the hardening rates is strongly correlated with accurate blind predictions of ductile fracture in the SFC specimens. Given that thermal softening can greatly affect hardening rates, we provided a thermographic analysis of deformation-induced heating and transient heat transfer in both the dogbone shaped samples and the SFC specimens. Transient heating in stainless steels is found to have first-order effects on the strain at the onset of necking, strain to fracture, as well as strain localization and ductile fracture in complex geometries even under so-called quasi-static loading rates.

42 ENGINEERING↗
DOE OSTI2024

Quarterly Research Performance Progress Report (Q8)

As part of Task 1, we have started by testing our modeling capabilities by reproducing isothermal DFIT simulations presented in the literature. Once satisfied with the results we have started by targeting the modeling of the DFITs at conducted at well 58-32. We have a identified a specific test (cycle 4 in zone 2) as the most interesting to be model with GEOS hydraulic fracturing module. Thus, we have first produced results with an isothermal model and adjusted model parameters to get a satisfying match with field pressure data. The, we have added thermal effects and compared the modeling results with and without thermal effects to estimate how thermal effects may influence test interpretation. Models seem to suggest that, for small volumes of fluid, thermal effects are moderate. In Task 2, we have adapted GEOS phase-field formulation to be able to simulate near-wellbore hydraulic fracture nucleation and propagation. We have devised a novel formulation that, compared to other existing ones, incorporates rock strengths. We have submitted a journal publication about our work. We are currently employing this phase-field formulation to model the experiments taking place at U Pitt and help us understand the effect of various parameters. In Task 3, we have built a model of the region surround well 16A and have started modeling stage 3 stimulation because of its simpler planar geometry. After calibrating simulation parameters using known analytical solutions, we have simulated the stage 3 stimulation using our isothermal hydraulic fracturing module, varying the permeability field, the stress conditions including different physics to get a better understanding of the numerical challenges and of the effects of varying these parameters on the simulation results. In Task 4 laboratory experimentation, a set of specialized drilling and injection tools has been customized and constructed to accommodate an inclined well with an orientation of up to 30 degrees relative to material anisotropy or principal stress axes. These inclined samples have also undergone thermal stress and hydraulic fracturing at a temperature of 190 degrees Celsius. Furthermore, both vertical and deviated sampling testing setups enable an extended analysis of post-peak pressure behaviors, facilitating post-test pressure analyses such as the G-function, step rate, and fracture reopening measurements. Thus, the key components of in-situ stress estimation can be extracted and validated through our experiment, providing a solid foundation for validating existing in-situ stress estimation theories or proposing new ones. Simultaneously, we are integrating computer vision techniques with traditional experimental fracture observation methods such as multi-overcore/slicing and water-penetration fracture observation. This combination will prove beneficial in populating the hydraulic fracture patterns database, generated under challenging EGS conditions. This approach aims to deepen our understanding of the complexities in EGS reservoirs and pave the way for future data-driven investigations. Additionally, PITT has also equipped the ELE International compression machine, which is now prepared for conducting indirect tensile and fracture toughness tests. These tests will aid in characterizing how rock fabrics influence the resulting fracture patterns. Additionally, we have completed the required personnel training and gained access to Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) for conducting more detailed characterization and analysis of rock fabrics, as well as the examination of thermal and hydraulically induced fracture patterns. Thus, the PITT team has effectively demonstrated the capabilities of our experimental apparatuses in exploring the thermal effects, well deviation angles, material anisotropy, and operational choices (such as circulation rate, injection fluid viscosity, and injection rate) and their impact on pressure responses and fracture trajectories under the Utah FORGE conditions.

15 GEOTHERMAL ENERGY↗
NASA NTRS2003

Jupiter System Data Analysis Program: Mechanisms, Manifestation, and Implications of Cryomagmatism on Europa

The objectives of the work completed under NASA Grant NAG5-8898 were (i) to document and characterize the low-albedo diffuse surfaces associated with triple bands and lenticulae, (ii) to determine their mechanisms of formation, and (iii) to assess the implications of these features for the resurfacing (in space and time) of the Europa and the nature of the Europan interior. The approach involved a combination of processing and analysis of Solid State Imaging data returned by the Galileo spacecraft during the primary and extended mission phases, together with numerical modeling of the physical processes interpreted to the observed features. We have modeled the formation of Europan triple explosive venting of cryoclastic material from bands and lenticulae halos by two processes: (i) a liquid layer in the Europan interior, and (ii) lag deposit formation by the thermal influence of subsurface cryomagmatic intrusions. We favor the latter hypothesis for explaining these features, and further suggest that a liquid water or brine intrusion is required to provide sufficient lateral heating of surface ice to explain the 25 km size of the largest features. (Solid ice diapirs, even under the most favorable conditions, become thermally exhausted before they heat significant lateral distances). We argue that water circulating in open fractures, or repeated cryomagmatic 'diking' events would provide sufficient thermal input to produce the observed features. Thus our work argues for the existence of a liquid beneath Europa's surface. Our results might most easily be explained by the presence of a continuous liquid layer (the putative Europan ocean); this would concur with the findings of the Galileo magnetometer team. However, we cannot rule out the possibility that discrete liquid pockets provide injections of fluid closer to the surface.

Fagents, Sarah A.↗
DOE OSTI2024

Modeling nuclear waste disposal in crystalline rocks at the Forsmark and Olkiluoto repository sites – Evaluation of potential thermal–mechanical damage to repository excavations

We conduct coupled thermo-hydro-mechanical modeling of a KBS-3V repository design in crystalline rocks, using data and conditions from the Forsmark in Olkiluoto repository sites in Sweden and Finland. The study focuses on repository performance related to the impact of thermal and hydraulic evolution on the potential for thermal–mechanical damage to underground repository excavations. For the designs and conditions considered at the Forsmark and Olkiluoto repository sites, the simulations show a peak temperature well under the adopted performance target of a 100°C maximum temperature, whereas there is still a high potential for thermal–mechanical damage to the KBS-3V waste deposition holes. The thermal–mechanical damage is much more likely if rock permeability is so low that it delays saturation and swelling of bentonite-clay-based backfill beyond the time for the thermal–mechanical peak, which occurs 50 to 100 years after nuclear waste deposition. We also found that sidewalls of the KBS-3V emplacement tunnels are vulnerable to tensile fracturing due to the combined effect of thermal stressing and backfill swelling. The study highlights a strong interaction between bentonite-based backfill and host rock through capillary suction along with induced rock desaturation. A careful design and selection of the bentonite-clay-based backfill materials for KBS-3V tunnels and deposition holes can facilitate a timely saturation and backfill swelling that in turn can minimize thermal–mechanical damage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2016

Annular Air Leaks in a Liquid Hydrogen Storage Tank

Large liquid hydrogen (LH2) storage tanks are vital infrastructure for NASA, the DOD, and industrial users. Over time, air may leak into the evacuated, perlite filled annular region of these tanks. Once inside, the extremely low temperatures will cause most of the air to freeze. If a significant mass of air is allowed to accumulate, severe damage can result from nominal draining operations. Collection of liquid air on the outer shell may chill it below its ductility range, resulting in fracture. Testing and analysis to quantify the thermal conductivity of perlite that has nitrogen frozen into its interstitial spaces and to determine the void fraction of frozen nitrogen within a perlite-frozen nitrogen mixture is presented. General equations to evaluate methods for removing frozen air, while avoiding fracture, are developed. A hypothetical leak is imposed on an existing tank and a full analysis of that leak is detailed. This analysis includes a thermal model of the tank and a time-to-failure calculation. Approaches to safely remove the frozen air are analyzed, leading to the conclusion that the optimal approach is to allow the frozen air to melt and use a water stream to prevent the outer shell from chilling.

Krenn, A. G.↗
DOE OSTI2024

Predicting Fracture Porosity Evolution in Sandstone

To better understand the porosity, strength, chemical reactivity, and patterns of fractures in the subsurface, we used evidence from mineral deposits in open fractures to unravel how fracture growth and diagenesis interact to create and destroy fracture porosity. Quartz cement textures and associated fluid inclusions and thermal histories provided data used to infer the duration and rates at which fractures open.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

High-burnup fuel stress analysis prior to and during a LOCA transient

High-burnup fuel fragmentation and pulverization have been experimentally observed during simulated loss-of-coolant accident (LOCA) transient testing of high-burnup (>62 GWd/tU) nuclear fuel. The cause of this phenomenon is generally accepted to be the formation of stresses arising from the off-normal conditions. However, the primary mechanism(s) contributing to the stress formation is/are still being debated. Leading hypotheses suggest that the concurrence of fission gas bubbles and high burnup structure on the pellet periphery (i.e., the rim) leave the fuel susceptible to pulverization. Other hypotheses suggest that pulverization is artificially inflated during externally heated tests that do not reproduce prototypic fuel stresses and radial temperature profiles as the fuel transitions from full-power nuclear heating to decay heating. This work performs finite element analyses of fuel pellet temperatures and macroscopic stresses prior to and during a LOCA transient to identify (1) operating conditions that may exacerbate the fuel pellet stress state, (2) differences in predicted stresses with nuclear vs. furnace heating, and (3) how fuel cracking impacts the subsequent stress state in the pellet fragments. Analyses predict that macroscopic transient fuel stresses resulting from constrained thermal expansion will remain below the fracture stress of fresh UO 2 once the fragment size reaches ~4 mm or less. Calculated fuel stresses from simulated LOCA tests performed with representative nuclear vs. electrical heating rates are shown to be equal within 5% and essentially unchanged for all times after the first 27 seconds of the transients. Because the fuel stresses do not change once the temperature profile becomes uniform, macroscopic transient stresses would be no different than those following a normal shutdown. Because pulverization of high burnup fuel does not occur prior to a LOCA test, pulverization of high burnup UO 2 cannot be initiated by differential thermal stresses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1974

Lunar mascons as consequences of giant impacts

An investigation is conducted regarding the effect of a giant impact on the thermal evolution of the moon. A model is proposed for the formation of the lunar mascons. The model takes into account the evidence of late volcanism during a period from about 3.7 to about 3.2 b.y. ago. It is found that a giant impact produces extensive fracturing in the region surrounding the basin and reduces the average thermal conductivity of the upper 20 km of this region by a factor of about 2. The less conductive ejecta blanket and the fractured zone behave as a thermal insulator. The lithosphere beneath the basin thickens monotonically and it becomes strong enough to support the mascon.

Arkani-Hamed, J.↗
DOE OSTI2021

Thermomechanical Microstructural Predictions of Fracture Nucleation of Zircaloy-4 Alloys With δ and ε Hydride Distributions

Abstract A crystalline dislocation-density formulation that was incorporated with a nonlinear finite-element (FE) method was utilized to understand and to predict the thermomechanical behavior of an hexagonal closest packed (h.c.p.) zircaloy system with hydrides with either face-centered cubic (f.c.c.) or body-centered cubic (b.c.c.) hydrides. This formulation was then used with a recently developed fracture methodology that is adapted for finite inelastic strains and multiphase crystalline systems to understand how different microstructurally based fracture modes nucleate and propagate. The interrelated microstructural characteristics of the different crystalline hydride and matrix phases with the necessary orientation relationships (ORs) have been represented, such that a detailed physical understanding of fracture nucleation and propagation can be predicted for the simultaneous thermomechanical failure modes of hydride populations and the matrix. The effects of volume fraction, morphology, crystalline structure, and orientation and distribution of the hydrides on simultaneous and multiple fracture modes were investigated for radial, circumferential, and mixed distributions. Another key aspect was accounting for temperatures changes due to the effects of thermal conduction and dissipated plastic work and their collective effects on fracture. For hydrided aggregates subjected to high temperatures, thermal softening resulted in higher ductility due to increased dislocation-density activity, which led to higher shear strain accumulation and inhibited crack nucleation and growth. The predictions provide validated insights into why circumferential hydrides are more fracture-resistant than radial hydrides for different volume fractions and thermomechanical loading conditions.

Engineering↗
NASA NTRS1983

Fracture toughness/Young's modulus correlation for low-density fibrous silica bodies

Fracture toughness and static Young's modulus were measured for the low-density silic fiber materials used as tiles in the thermal protection system of the Space Shuttle. The fracture behavior was found to be in excellent agreement with a previously formulated micromechanical model and allowed both (density) classes of tile material to be correlated to a single function. A similar correlation was also found between strength and Young's modulus, which is the basis of a nondestructive evaluation test for these materials. It was shown that the value of Young's modulus determined from a dynamic test can be substantially greater than that determined in a static mechanical test. This effect must be taken into account in the correlation. Finally, it was also determined that these materials have significant variations in Kc, both within and between production units, so that the strength variability in these materials is dependent on both fracture toughness and flaw-size variations.

Green, D. J.↗
NASA NTRS1974

Model for thermal stress resistance of truly elastic materials containing more than one crack

The model was developed upon the physical properties of surface energy and intrinsic modulus of elasticity of a material containing a number of equal sized microcracks which are independent of one another. The effect of these cracks upon the strain energy per unit volume of material necessary to continue simultaneous crack growth as well as the measured physical properties was established, and the thermal stress resistance is developed in terms of this energy. The model is expressed in its final form in terms of the measured physical properties of fracture strength, effective modulus of elasticity, and coefficient of thermal expansion. The model was applied to existent thermal stress data of ceramic materials for which these physical properties had been measured. On the basis of these data it was concluded that the thermal stress resistance of a material may be improved by increasing the fracture strength.

Lineback, L. D.↗
DOE OSTI2023

Utah FORGE 5-2565: Hydrothermal Evolution of Fracture Properties - Workshop Presentation

This is a presentation on the Evolution of Permeability and Strength Recovery of Shear Fractures Under Hydrothermal Conditions project by the U.S. Geological Survey, presented by Dr. David Lockner. The project's objective was to determine how thermal, hydraulic, mechanical, and chemical processes affect the sustainability of fracture networks in geothermal reservoirs and provide strategies for improved EGS techniques that maximize thermal coupling and increase reservoir longevity. This presentation was featured in the Utah FORGE R&D Annual Workshop on September 8, 2023. The workshop provided a valuable opportunity to explore the progress made in each of the 17 Research and Development projects funded under Solicitation 2020-1 which aim to enhance our understanding of the crucial factors influencing the development of Enhanced Geothermal Systems (EGS) reservoirs and resources.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Charpy Impact Characterization of Surveillance Specimens Harvested from Palisades High Fluence A-60 Capsule

Located on the shores of Lake Michigan, the Palisades Nuclear Generating Station (PNGS) was a nuclear power plant that operated in Covert Township, Michigan. The plant had a single pressurized water reactor that produced electricity for the region. The PNGS was shut down in 2022 after more than four decades of service. The PNGS included in its surveillance program a surveillance capsule, designated A-60, containing specimens of a weld metal with nickel content of about 1.36 wt% and copper content of about 0.25 wt%. The capsule was removed from its surveillance position in early 1995 and has been resident in the spent fuel pool since that time. This capsule was irradiated to a fluence of 1.96×10 20 n/cm 2 (E>1MeV) that is equivalent for more than 150 effective full power years (EFPYs) for the US reactor pressure vessel (RPV) fleet. The material is also of special interest because of its very high nickel content and potential for development of NiMnSi (nickel-manganese-silicon) precipitates. Combination of very high fluence and very high Ni and Cu content makes the material in this capsule of great interest as benchmark for currently developing embrittlement trend curves (ETC) aiming to predict embrittlement at high fluences. Multi-year efforts by the Light Water Reactor Sustainability (LWRS) Program personnel from the Materials Research Pathway (MRP) to harvest this capsule finally succeeded in 2023. As a result, the Westinghouse Electric Company (WEC) through contract with Oak Ridge National Laboratory (ORNL) came to PNGS site, retrieved the A-60 capsule, brought it to WEC Churchill hot cell facility, opened the capsule and sent all surveillance specimens in the capsule to ORNL for future characterization by July 2023. Total of 9 tensile and 48 Charpy specimens were inventoried in the ORNL hot cells. Testing plan has been developed based on available specimens. It includes hardness, tensile, Charpy impact, Mini-CT fracture toughness testing, in-situ thermal annealing, and microstructural characterization, including Atom Probe Tomography (APT). Charpy impact testing has been completed and results are presented in this report. Moreover, negotiations with Pressurized Water Reactors Owners Group (PWROG) and Westinghouse resulted in Westinghouse donating to ORNL a piece of archive weld and base metal such that unirradiated characterization of these materials can be performed as part of this project. Comparison of measured hardening and embrittlement has been performed and data are compared to available large database.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗