SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This paper describes the development of a unique strain measuring device which is intended to monitor the state of strain in thin balloon films during flight. The gate is bonded directly to the film without significantly altering the state of strain or stress in the wall of the balloon. Results of a model balloon inflation are presented which indicate the gage to measure strain in a deployed balloon.
Combined Load Diagrams for Direct-Read, Force, and Moment Balances are discussed in great detail in the paper. The diagrams, if compared with a corresponding combined load plot of a balance calibration data set, may be used to visualize and interpret basic relationships between the applied balance calibration loads and the load components at the forward and aft gage of a strain-age balance. Lines of constant total force and moment are identified in the diagrams. In addition, the lines of pure force and pure moment are highlighted. Finally, lines of constant moment arm are depicted. It is also demonstrated that each quadrant of a Combined Load Diagram has specific regions where the applied total calibration force is at, between, or outside of the balance gage locations. Data from the manual calibration of a Force Balance is used to illustrate the application of a Combined Load Diagram to a realistic data set.
Strain gauges for use at cryogenic temperatures
Electrical-resistance strain gauges - high strain response, hysteresis, strain sensitivity, creep, zero drift & resistance at cryogenic temperatures
Flight strain gauge system for Centaur /AC-6/ LIQUID hydrogen fuel tank skin
Strain gauge accelerometer based on anisotropic stress effect in P-N junctions using piezoelectric crystals
Explore the source record for details and available documents.
An improved version of an algorithm is presented that uses a weighted least squares fit of balance calibration data for the generation of the balance load prediction equations. The weighted least squares fit assigns a weighting factor between zero and one to each calibration data point that depends on a simple count of the number of intentionally loaded balance gages. The greater the number of the loaded gages is, the smaller a data point's weighting factor becomes. This strategy has two advantages. First, single-component loads become more influential during the regression analysis of the calibration data. In addition, the negative influence of load schedule asymmetries on the regression analysis results can more effectively be controlled. The original algorithm of 2017 was improved in 2020. Now, gage output differences relative to the natural zeros are exclusively used as input for the determination of the number of intentionally loaded gages. The improved weighted least squares fit can be applied with both the Non-Iterative Method and the Iterative Method that are used for the balance load prediction in the aerospace testing community. Machine calibration data of a force balance is used to illustrate benefits of the application of the improved weighted least squares fit of balance calibration data.
Data from a five-component semi-span balance is used to perform a systematic comparison of the load prediction accuracy of two load prediction methods. Both methods independently obtain the load prediction equations from multivariate least squares fits of balance calibration data. The first method is called the Non-Iterative Method. This approach directly uses regression models of the individual load components of a balance for the load prediction. The second method is called the Iterative Method. This alternate approach uses a load iteration equation for the load prediction that is constructed from the regression coefficients of the gage outputs of the balance. Basic characteristics of the two methods are reviewed. Afterwards, both methods are applied to calibration, check load, and wind tunnel test data of a five-component semi-span balance. Selected analysis results are compared. These comparisons confirm that the accuracy of the two methods is the same for all practical purposes.
A new approach for the graphical and numerical description of balance interactions is presented. The approach uses data from single-component loads as input. This choice has the two advantages. First, the number of applied loads is at the minimum needed for interactions to be observed. In addition, the loads used for the description of interactions can easily be repeated at different sites. Output differences relative to the outputs of the zero load point of a load series are used for the description of interactions. Similarly, load differences relative to the loads of the zero load point of a load series are used for the description of the loads. Interactions are plotted versus the load differences for each load component while omitting the outputs of the primary gage of the chosen load component. The resulting plots have a characteristic star pattern as interactions are zero at zero load. Numerical estimates of the slopes of the interactions can be reverse-engineered from the load prediction equations of a balance if calibration data is examined. The slopes are the off-diagonal coefficients of the inverse of the matrix that has the coefficients of the linear terms of the fitted loads if the Non-Iterative Method is used for the analysis. Similarly, the slopes are the off-diagonal coefficients of the inverse of the matrix that is the non-iterative part of the primary load iteration equation if the Iterative Method is used for the analysis. Data from the calibration of a force balance is processed to illustrate the proposed graphical and numerical description of interactions.
The load schedule for the calibration of a six-component force balance in a calibration machine was improved. Now, single-component loads are repeated in regular intervals during the calibration. This approach has several advantages. First, the number of single-component loads increases to about twenty-two percent of all loads and load combinations. Consequently, more accurate numerical estimates of the primary bridge sensitivities can be obtained if global regression is used for the analysis of the calibration data. In addition, single-component repeats make it possible to track the stability of the applied loads during the calibration process. Finally, interactions of single-component repeats can be compared with interactions that are observed during the application of manual loads to the balance. Machine calibration and manual data sets of two force balances are used to illustrate benefits of the new load schedule. It is shown in the examples how differences between the observed interactions of machine calibration and manual data can be quantified. The suggested improvements can also be implemented in the load schedule for the machine calibration of a moment or direct-read balance as long as single-component loads are included that are described in the design load format of the balance.
Cryogenic strain gauge application to circumferential loads of Centaur hydrogen tank insulation while in launch configuration
Explore the source record for details and available documents.
Explore the source record for details and available documents.
An apparatus and method are described for calibrating high temperature strain gases which serve for both dead weight and constant deflection measurements. A cantilever support arm allows the test unit to slide into a furnace while one end is subjected to bending strain either by hanging weights upon it or by deflecting it with a push rod. The dual nature of the fixture permits both tests to be run without change of the test specimen or removal from the furnace.
Technique employs application of pressure and ultrasound to effect welding of encapsulated strain gates to metallic surfaces. Process requires no heat or adhesives. Technique might also be used to simplify curing of epoxy adhesives and for attachment problems like bonding cryogenic temperature sensors to structural parts.
Explore the source record for details and available documents.
Explore the source record for details and available documents.