SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Statistical analysis of design criteria for radio frequency proton event warning system
Ideally, a statistically representative sample of measured high-resolution wind profiles with wavelengths as small as tens of meters is required for assessment of launch vehicle ascent flight systems component capability and vehicle operability for a selected launch site. At most potential launch sites a sample of high-resolution measured wind profiles may not exist. Representative samples of Rawinsonde wind profiles are more likely to be available because of the extensive network of measurement sites established for routine measurements at 12-hr intervals in support of national and international weather observing and forecasting activity. Such a sample, although large enough to statistically represent relatively large wavelength perturbations, would be inadequate for launch system design assessment applications because the Rawinsonde system can accurately measure wind perturbations with wavelengths no smaller than 2000m (1000m altitude increment). Wavelengths less than 2000m in the raw Rawinsonde data, which tend to be dominated by un-damped spurious balloon motion and radar tracking system noise, are filtered within the data processing scheme. The Kennedy Space Center (KSC) Jimsphere wind profiles (150/month and seasonal pairs) are the only adequate high resolution (approximately 150 to 300m effective resolution, but over-sampled at 25m intervals) data that have been used extensively in launch vehicle design, operability assessments and operational protection of vehicle systems for wind perturbation uncertainty. Jimsphere wind profiles have been measured at a few other potential launch sites but the number of profiles is relatively small and the samples are not statistically representative of the site dependent wind profile variability. A simulation process has been developed for enhancement of measured low-resolution Rawinsonde profiles that are more likely to be available in the vicinity of potential launch sites and are a statistically representative sample of wind profile perturbation wavelengths greater than 2000m. The enhancement produces perturbed wind profiles with wavelengths as small as desired for application in launch vehicle ascent flight simulations and design assessments.
A probabilistic methodology for designing rotating mechanical components using reliability to relate stress to strength is explained. The experimental test machines and data obtained for steel to verify this methodology are described. A sample mechanical rotating component design problem is solved by comparing a deterministic design method with the new design-by reliability approach. The new method shows that a smaller size and weight can be obtained for specified rotating shaft life and reliability, and uses the statistical distortion-energy theory with statistical fatigue diagrams for optimum shaft design. Statistical methods are presented for (1) determining strength distributions for steel experimentally, (2) determining a failure theory for stress variations in a rotating shaft subjected to reversed bending and steady torque, and (3) relating strength to stress by reliability.
The cost and safety goals for NASA's next generation of reusable launch vehicle (RLV) will require that rapid high-fidelity aerothermodynamic design tools be used early in the design cycle. To meet these requirements, it is desirable to establish statistical models that quantify and improve the accuracy, extend the applicability, and enable combined analyses using existing prediction tools. The research work was focused on establishing the suitable mathematical/statistical models for these purposes. It is anticipated that the resulting models can be incorporated into a software tool to provide rapid, variable-fidelity, aerothermal environments to predict heating along an arbitrary trajectory. This work will support development of an integrated design tool to perform automated thermal protection system (TPS) sizing and material selection.
The cost and safety goals for NASA s next generation of reusable launch vehicle (RLV) will require that rapid high-fidelity aerothermodynamic design tools be used early in the design cycle. To meet these requirements, it is desirable to identify adequate statistical models that quantify and improve the accuracy, extend the applicability, and enable combined analyses using existing prediction tools. The initial research work focused on establishing suitable candidate models for these purposes. The second phase is focused on assessing the performance of these models to accurately predict the heat rate for a given candidate data set. This validation work compared models and methods that may be useful in predicting the heat rate.
Criteria to determine the probability of aircraft structural failure were established according to the Quantitative Structural Design Criteria by Statistical Methods, the QSDC Procedure. This criteria method was applied to the design of the space shuttle during this contract. An Applications Guide was developed to demonstrate the utilization of the QSDC Procedure, with examples of the application to a hypothetical space shuttle illustrating the application to specific design problems. Discussions of the basic parameters of the QSDC Procedure: the Limit and Omega Conditions, and the strength scatter, have been included. Available data pertinent to the estimation of the strength scatter have also been included.
The use of statistical techniques to build approximations of expensive computer analysis codes pervades much of todays engineering design. These statistical approximations, or metamodels, are used to replace the actual expensive computer analyses, facilitating multidisciplinary, multiobjective optimization and concept exploration. In this paper we review several of these techniques including design of experiments, response surface methodology, Taguchi methods, neural networks, inductive learning, and kriging. We survey their existing application in engineering design and then address the dangers of applying traditional statistical techniques to approximate deterministic computer analysis codes. We conclude with recommendations for the appropriate use of statistical approximation techniques in given situations and how common pitfalls can be avoided.
Results are reported for a study designed to determine statistically the nature and variation of the polarization parameters of Pc3 magnetic pulsations at synchronous orbit. Data obtained with a triaxial flux gate magnetometer on the geosynchronous satellite ATS 6 are subjected to routine power spectral and polarization analyses, and the events examined are identified as peaks in the spectra. Coherence analysis of spectral matrices for these events indicates that Pc3 are very common at synchronous orbit and are primarily a local morning phenomenon with an occurrence peak around 1000 LT; that the pulsations occur at all frequencies in the Pc3 band, with the most common frequency at about 0.35 Hz; that the Pc3 at synchronous orbit are most often linear and generally transverse, but some have significant compressional components; and that based on azimuth angle, there are two distinct classes of Pc3 (azimuthal and radial) with different characteristics. These statistical results are compared with model predictions and ground-based observations.
A characteristic feature of rainfall statistics is that they depend on the space and time scales over which rain data are averaged. A previously developed spectral model of rain statistics that is designed to capture this property, predicts power law scaling behavior for the second moment statistics of area-averaged rain rate on the averaging length scale L as L right arrow 0. In the present work a more efficient method of estimating the model parameters is presented, and used to fit the model to the statistics of area-averaged rain rate derived from gridded radar precipitation data from TOGA COARE. Statistical properties of the data and the model predictions are compared over a wide range of averaging scales. An extension of the spectral model scaling relations to describe the dependence of the average fraction of grid boxes within an area containing nonzero rain (the "rainy area fraction") on the grid scale L is also explored.
Although applications for Statistical Energy Analysis (SEA) techniques are more widely used in the aerospace industry today, opportunities to anchor the response predictions using measured data from a flight-like launch vehicle structure are still quite valuable. Response and excitation data from a ground acoustic test at the Marshall Space Flight Center permitted the authors to compare and evaluate several modeling techniques available in the SEA module of the commercial code VA One. This paper provides an example of vibration response estimates developed using different modeling approaches to both approximate and bound the response of a flight-like vehicle panel. Since both vibration response and acoustic levels near the panel were available from the ground test, the evaluation provided an opportunity to learn how well the different modeling options can match band-averaged spectra developed from the test data. Additional work was performed to understand the spatial averaging of the measurements across the panel from measured data. Finally an evaluation/comparison of two conversion approaches from the statistical average response results that are output from an SEA analysis to a more useful envelope of response spectra appropriate to specify design and test vibration levels for a new vehicle.
The National Meteorological Center Barotropic-Mesh Model has been used to test a statistical correction procedure, designated as M-II, that was developed in Schemm et al. (1981). In the present application, statistical corrections at 12 h resulted in significant reductions of the mean-square errors of both vorticity and the Laplacian of thickness. Predictions to 48 h demonstrated the feasibility of applying corrections at every 12 h in extended forecasts. In addition to these improvements, however, the statistical corrections resulted in a shift of error from smaller to larger-scale motions, improving the smallest scales dramatically but deteriorating the largest scales. This effect is shown to be a consequence of randomization of the residual errors by the regression equations and can be corrected by spatially high-pass filtering the field of corrections before they are applied.
This report documents the efforts of a Georgia Tech High Speed Civil Transport (HSCT) aerospace student design team in completing a design methodology demonstration under NASA's Advanced Design Program (ADP). Aerodynamic and propulsion analyses are integrated into the synthesis code FLOPS in order to improve its prediction accuracy. Executing the integrated product and process development (IPPD) methodology proposed at the Aerospace Systems Design Laboratory (ASDL), an improved sizing process is described followed by a combined aero-propulsion optimization, where the objective function, average yield per revenue passenger mile ($/RPM), is constrained by flight stability, noise, approach speed, and field length restrictions. Primary goals include successful demonstration of the application of the response surface methodolgy (RSM) to parameter design, introduction to higher fidelity disciplinary analysis than normally feasible at the conceptual and early preliminary level, and investigations of relationships between aerodynamic and propulsion design parameters and their effect on the objective function, $/RPM. A unique approach to aircraft synthesis is developed in which statistical methods, specifically design of experiments and the RSM, are used to more efficiently search the design space for optimum configurations. In particular, two uses of these techniques are demonstrated. First, response model equations are formed which represent complex analysis in the form of a regression polynomial. Next, a second regression equation is constructed, not for modeling purposes, but instead for the purpose of optimization at the system level. Such an optimization problem with the given tools normally would be difficult due to the need for hard connections between the various complex codes involved. The statistical methodology presents an alternative and is demonstrated via an example of aerodynamic modeling and planform optimization for a HSCT.
The ATS-F Comsat Millimeter Wave Propagation Experiment has been designed to gather statistical data on the attenuation caused by rain at millimeter wave frequencies. These data will be used to determine system design parameters for future communications satellite systems operating at frequencies above 10 GHz. The experiment has 39 ground terminals transmitting at 13.2 or 17.8 GHz to a transponder on board the ATS-F satellite. The transponder retransmits these signals at 4 GHz to a central earth terminal which records their amplitudes once each second. The data will be analyzed to provide probabilities of attenuation as functions of parameters such as rainfall, location, and time. These probabilities can then be used to determine the required power margins of millimeter wave communications systems. Techniques of overcoming severe attenuation such as site diversity and the use of a spot beam to increase the power level at selected locations will also be evaluated.
The ATS-6 COMSAT Propagation Experiment was designed to gather statistical data on attenuation caused by rain and snow at 13 and 18 GHz. These data will be used to determine system design parameters for future communications satellite systems operating at frequencies above 10 GHz. The experiment used 25, 18 GHz, and 15, 13 GHz unattended ground transmitters at 25 locations in the eastern U.S. to transmit to the ATS-6. The ATS-6 transponder converts these carriers to frequencies around 4150 MHz and transmits these signals to the COMSAT large horn antenna/data acquisition and receiving facility at Andover, Me. This facility calibrates and digitally records each carrier once per second. These data have been processed and analyzed for the period from July to Nov. 2, 1972. Plans are being made to conduct the experiment in Europe and India during the 35 deg E longitude site phase of ATS-6 operations.
A statistical interpolation technique is presented for modeling GaAs FET S-parameter measurements for use in the statistical analysis and design of circuits. This is accomplished by interpolating among the measurements in a GaAs FET S-parameter data base in a statistically valid manner.
Three decades of research in molecular nanomagnets have raised their magnetic memories from liquid helium to liquid nitrogen temperature thanks to a wise choice of the magnetic ion and coordination environment. Still, serendipity and chemical intuition played a main role. In order to establish a powerful framework for statistically driven chemical design, here we collected chemical and physical data for lanthanide-based nanomagnets, catalogued over 1400 published experiments, developed an interactive dashboard (SIMDAVIS) to visualise the dataset, and applied inferential statistical analysis. Our analysis shows that the Arrhenius energy barrier correlates unexpectedly well with the magnetic memory. Furthermore, as both Orbach and Raman processes can be affected by vibronic coupling, chemical design of the coordination scheme may be used to reduce the relaxation rates. Indeed, only bis-phthalocyaninato sandwiches and metallocenes, with rigid ligands, consistently present magnetic memory up to high temperature. Analysing magnetostructural correlations, we offer promising strategies for improvement, in particular for the preparation of pentagonal bipyramids, where even softer complexes are protected against molecular vibrations.
The Application Research Toolbox (ART) is a collection of computer programs that implement algorithms and mathematical models for simulating remote sensing systems. The ART is intended to be especially useful for performing design-tradeoff studies and statistical analyses to support the rational development of design requirements for multispectral imaging systems. Among other things, the ART affords a capability to synthesize coarser-spatial-resolution image-data products. The ART also provides for simulations of image-degradation effects, including point-spread functions, misregistration of spectral images, and noise. The ART can utilize real or synthetic data sets, along with sensor specifications, to create simulated data sets. In one example of a particular application, simulated imagery of a coarse resolution system was created using high-resolution imagery from another system in order to perform a radiometric cross-comparison. In the case of a proposed sensor system, the simulated data can be used to conduct trade studies and statistical analyses to ensure that the sensor system will satisfy the requirements of potential scientific, academic, and commercial user communities.
The Application Research Toolbox (ART) is a collection of computer programs that implement algorithms and mathematical models for simulating remote sensing systems. The ART is intended to be especially useful for performing design-tradeoff studies and statistical analyses to support the rational development of design requirements for multispectral imaging systems. Among other things, the ART affords a capability to synthesize coarser-spatial-resolution image-data sets from finer-spatial-resolution data sets and multispectral-image-data products from hyperspectral-image-data products. The ART also provides for synthesis of image-degradation effects, including point-spread functions, misregistration of spectral images, and noise. The ART can utilize real or synthetic data sets, along with sensor specifications, to create simulated data sets. In one example of a typical application, simulated data pertaining to an existing multispectral sensor system are used to verify the data collected by the system in operation. In the case of a proposed sensor system, the simulated data can be used to conduct trade studies and statistical analyses to ensure that the sensor system will satisfy the requirements of potential scientific, academic, and commercial user communities.