Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “spark ignition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Some Notes on Sparks and Ignition of Fuels

This report compliments a concurrent analysis of the electromagnetic field threat to the fuel system of a transport aircraft. The accompanying effort assessed currents, voltages and power levels that may be induced upon fuel tank wiring from radio transmitters (inside and outside the aircraft). In addition to this, it was also essential to determine how much voltage, current, or power is required to create a fuel-vapor ignition hazard. The widely accepted minimum guideline for aircraft fuel-vapor ignition is the application of a 0.2 millijoule energy level. However, when considering radio frequency (RF) sources, this guideline is seriously inadequate. This report endeavors to bridge the gap between a traditional understanding of electrical breakdown, heating and combustion; and supplement the knowledge with available information regarding aircraft fuel-vapor ignition by RF sources

Fisher, Franklin A.↗
DOE OSTI2024

Development of prechamber enabled mixing-controlled combustion strategy for ultra-low methane emissions from lean burn natural gas engines

This numerical study explores the optimization of Prechamber Enabled Mixing-Controlled Combustion (PC-MCC) using natural gas in heavy-duty engines, aiming to enhance combustion efficiency to minimize methane slip and NOx emissions. The approach involves a prechamber ignition system, distinct from conventional spark ignition (SI) systems, to initiate combustion of direct injected natural gas. By leveraging the robust ignition characteristics of the prechamber, the PC-MCC method demonstrates significant potential in achieving efficient combustion akin to diesel engines but with lower greenhouse gas emissions. The research evaluates the effects of various geometric and operational parameters on the combustion process and emissions, including prechamber volume, nozzle diameter, direct injector (DI) geometry, and engine operating strategies. Computational Fluid Dynamics (CFD) simulations are utilized, focusing on a heavy-duty, single-cylinder engine modeled after the Caterpillar C9.3B engine. Key findings indicate that a prechamber volume of 3 cc, coupled with a nozzle diameter of 2.75 mm for two prechamber holes, strikes an optimal balance between combustion efficiency and emissions reduction. This configuration ensures robust combustion across a range of operating conditions while maintaining methane slip within targeted limits. Further investigation into DI geometry shows the significance of the injector umbrella angle and nozzle diameter in shaping the fuel-air mixing and combustion dynamics. An umbrella angle of 130° and a nozzle diameter of 300 microns are identified as optimal, promoting rapid and efficient combustion with minimized methane and NOx emissions. The study also investigates the impact of injection timing and pressure, highlighting their roles in controlling combustion timing and influencing emissions levels. Advanced injection timing is found to be crucial in achieving the desired low methane slip, whereas retarded injection timing assists to reduce NOx emissions while having a slight increase in methane emissions. Operating strategies incorporating various levels of Exhaust Gas Recirculation (EGR) are assessed for their effectiveness in further reducing emissions. The research demonstrates that a judicious combination of internal hot EGR and careful calibration of DI pressure and SOI timing can achieve significant reductions in NOx emissions while keeping methane slip under control. Specifically, an internal EGR level of 15%–25%, combined with DI pressures of 200–300 bar and injection timings at or after top dead center, is recommended. These findings contribute valuable insights into the development of advanced combustion techniques for natural gas engines, offering a viable pathway to reduce methane slip without compromising engine efficiency or performance. The PC-MCC system presents a promising solution for the future of heavy-duty natural gas engine technology to reduce methane emissions.

Nsaif, Osama↗
NASA NTRS1950

Relation Between Inflammables and Ignition Sources in Aircraft Environments

A literature survey was conducted to determine the relation between aircraft ignition sources and inflammables. Available literature applicable to the problem of aircraft fire hazards is analyzed and, discussed herein. Data pertaining to the effect of many variables on ignition temperatures, minimum ignition pressures, and minimum spark-ignition energies of inflammables, quenching distances of electrode configurations, and size of openings incapable of flame propagation are presented and discussed. The ignition temperatures and the limits of inflammability of gasoline in air in different test environments, and the minimum ignition pressure and the minimum size of openings for flame propagation of gasoline - air mixtures are included. Inerting of gasoline - air mixtures is discussed.

Scull, Wilfred E↗
NASA NTRS2016

Green Monopropellant Status at Marshall Space Flight Center

NASA Marshall Space Flight Center is continuing investigations into the use of green monopropellants as a replacement for hydrazine in spacecraft propulsion systems. Work to date has been to push technology development through multiple activities designed to understand the capabilities of these technologies. Future work will begin to transition to mission pull as these technologies are mature while still keeping a solid goal of pushing technology development as opportunities become available. The AF-M315E activities began with hot-fire demonstration testing of a 1N monopropellant thruster in FY 14 and FY15. Following successful completion of the preliminary campaign, changes to the test stand to accommodate propellant conditioning capability and better control of propellant operations was incorporated to make testing more streamlined. The goal is to conduct hot-fire testing with warm and cold propellants using the existing feed system and original thruster design. Following the 1N testing, a NASA owned 100 mN thruster will be hot-fire tested in the same facility to show feasibility of scaling to smaller thrusters for cubesat applications. The end goal is to conduct a hot-fire test of an integrated cubesat propulsion system using an SLM printed propellant tank, an MSFC designed propulsion system electronic controller and the 100 mN thruster. In addition to the AF-M315E testing, MSFC is pursuing hot-fire testing with LMP-103S. Following our successful hot-fire testing of the 22N thruster in April 2015, a test campaign was proposed for a 440N LMP-103S thruster with Orbital ATK and Plasma Processes. This activity was funded through the Space Technology Mission Directorate (STMD) ACO funding call in the last quarter of CY15. Under the same funding source a test activity with Busek and Glenn Research Center for testing of 5N AF-M315E thrusters was proposed and awarded. Both activities are in-work with expected completion of hot-fire testing by the end of FY17. MSFC is continuing to coordinate with the AF and academia on understanding the chemical reactions that occur in AF-M315E. An on-going investigation of the catalyst bed species using Raman Spectroscopy through the NASA Technology Research Fellowship Program (NSTRF) is looking for ways to minimize the amount of computation required by understanding the intermediate species created in the catalyst bed. The MSFC team is also working with commercial partners through Cooperative Agreement Notices (CAN's). Partnerships with commercial and academia include work in non-catalytic ignition of AF-M315, spark ignition of hybrid cubesat systems, printed SLM tanks, and dual-mode (electric and chemical) propulsion systems is continuing.

Burnside, Christopher G.↗
NASA NTRS1985

Transition region ignition characteristics of n-heptane fuel sprays

Ignition studies were perferred on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. The effect of spark duration on ignition frequency for several spark energies was determined for equivalence ratios of 0.5 and 1.0 and initial droplet diameters of 28 and 68 microns. Spark duration had little effect on ignition frequency over the entire 15 to 170 mu s range examined. Spark durations of 70 to 80 mu s were used for all subsequent work. The spark gap was optimized at equivalence ratios of 0.6, 0.8 and 1.0 and initial droplet diameters of 30, 40, 50, 60 and 70 microns by varying the electrode spacing from 0.5 to 5.0 mm while maintaining a constant spark energy. The optimum gap was determined to be 3.0 mm for nearly all conditions.

Danis, A. M.↗
DOE OSTI2022

Fuel property impacts on gaseous and PM emissions from a multi-mode single-cylinder engine

The U.S. Department of Energy’s Co-Optima initiative has focused on improving fuel economy and vehicle performance while reducing emissions through the simultaneous development of emerging sustainable fuels with beneficial properties and advanced combustion strategies. A major thrust has been the development of advanced compression ignition (ACI) combustion strategies of gasoline range fuels in combination with spark-ignited (SI) combustion in a single engine capable of multi-mode operation to achieve high power density with enhanced part load efficiency. The aim of this study was to further the understanding of how emissions from both ACI and SI strategies operating on the same fuels in the same engine are impacted by different fuel properties. This investigation focused on particulate matter (PM) and gaseous hydrocarbon emissions from 6 different fuels across 3 different combustion modes on the same single-cylinder engine designed for multi-mode operation: SI combustion, partial fuel stratification (PFS), and spark-assisted compression ignition (SACI). In each of these modes, 3 different CA50 phasings were studied such that all 6 fuels could be studied at the same phasings. Three of the six different fuels used were specially formulated in a previous investigation to study the impact of fuel distillation and aromatic content while maintaining the research octane number (RON) and octane sensitivity. Additionally, neat isooctane and two ethanol containing fuels (RD5-87 and Co-Optima E30) were studied. Different fuel and phasing impacts on emissions were observed across the three combustion modes. Fuel properties were found to impact soot PM and particle number more than the CA50 phasing, while the phasing had more impact on NOx emissions. The NOx emissions were reduced in the PFS mode for all fuels compared to SI combustion, but the SACI combustion mode did not reduce NOx emissions. Although PFS produced low soot PM emissions like SI, total PM mass emissions were significantly higher due to large organic carbon (OC) PM mass contribution. Both PFS and SACI had greater particle number emission than SI operation with small nuclei mode particles dominating in PFS compared to large agglomeration particles in SACI.

42 ENGINEERING↗
DOE OSTI2023

Analysis of Real-World Preignition Data Using Neural Networks

Increasing adoption of downsized, boosted, spark-ignition engines has improved vehicle fuel economy, and continued improvement is desirable to reduce carbon emissions in the near-term. However, this strategy is limited by damaging preignition events which can cause hardware failure. Research to date has shed light on various contributing factors related to fuel and lubricant properties as well as calibration strategies, but the causal factors behind an individual preignition cycle remain elusive. If actionable precursors could be identified, mitigation through active control strategies would be possible. This paper uses artificial neural networks to search for identifiable precursors in the cylinder pressure data from a large real-world data set containing many preignition cycles. It is found that while follow-up preignition cycles in clusters can be readily predicted, the initial preignition cycle is not predictable based on features of the cylinder pressure. Further, this indicates that the alternating pattern of preignition cycles within clusters is influenced by the thermodynamic state as reflected in the pressure, but that the trigger for the initial preignition cycle is not thermodynamic in nature, but more likely tied to a critical threshold in the chemistry of the fuel/lubricant mixture in the upper crevice or other factors related to the presence of an ignition source.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Optical Investigation of a Partial Fuel Stratification Strategy to Stabilize Overall Lean Operation of a DISI Engine Fueled with Gasoline and E30

This paper offers new insights into a partial fuel stratification (PFS) combustion strategy that has proven to be effective at stabilizing overall lean combustion in direct injection spark ignition engines. To this aim, high spatial and temporal resolution optical diagnostics were applied in an optically accessible engine working in PFS mode for two fuels and two different durations of pilot injection at the time of spark: 210 µs and 330 µs for E30 (gasoline blended with ethanol by 30% volume fraction) and gasoline, respectively. In both conditions, early injections during the intake stroke were used to generate a well-mixed lean background. The results were compared to rich, stoichiometric and lean well-mixed combustion with different spark timings. In the PFS combustion process, it was possible to detect a non-spherical and highly wrinkled blue flame, coupled with yellow diffusive flames due to the combustion of rich zones near the spark plug. The initial flame spread for both PFS cases was faster compared to any of the well-mixed cases (lean, stoichiometric and rich), suggesting that the flame propagation for PFS is enhanced by both enrichment and enhanced local turbulence caused by the pilot injection. Different spray evolutions for the two pilot injection durations were found to strongly influence the flame kernel inception and propagation. PFS with pilot durations of 210 µs and 330 µs showed some differences in terms of shapes of the flame front and in terms of extension of diffusive flames. Yet, both cases were highly repeatable.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1985

Ignition characteristics of rich n-heptane fuel sprays in the transition region

Ignition studies were performed on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. Using the optimum electrode spacing and spark duration, the frequency of ignition was determined as a function of spark energy for three overall equivalence ratios (0.6, 0.8, and 1.0) and for initial droplet diameters of 25, 40, 50, 60, and 70 microns. An LDA system was used to determine the actual equivalence ratio at the spark gap, which varied from 1.5 to 4.7. The spark energy at which the frequency of ignition was 90 percent was defined as the minimum ignition energy. These data indicated that the ignitability of the sprays was enhanced as the equivalence ratio was increased, but was diminished as the droplet size was increased. The increase in minimum ignition energy with increasing droplet size and fixed equivalence ratio was nearly linear over the range of parameters studied. However, the effect became smaller with increasing equivalence ratio.

Danis, A. M.↗
NASA NTRS2004

Chemistry of Aviation Fuels

Minimum ignition energies of various methanol/air mixtures were measured in a temperature controlled constant volume combustion vessel using a spark ignition method with a spark gap distance of 2 mm. The minimum ignition energies decrease rapidly as the mixture composition (equivalence ratio, Phi) changes from lean to stoichiometric, reach a minimum value, and then increase rather slowly with Phi. The minimum of the minimum ignition energy (MIE) and the corresponding mixture composition were determined to be 0.137 mJ and Phi = 1.16, a slightly rich mixture. The variation of minimum ignition energy with respect to the mixture composition is explained in terms of changes in reaction chemistry.

Knepper, Bryan↗
NASA NTRS1986

Combustion characteristics in the transition region of liquid fuel sprays

A number of important effects have been observed in the droplet size transition region in spray combustion systems. In this region, where the mechanism of flame propagation is transformed from diffusive to premixed dominated combustion, the following effects have been observed: (1) maxima in burning velocity; (2) extension of flammability limits; (3) minima in ignition energy; and (4) minima in NOx formation. A monodisperse aerosol generator has been used to form and deliver a well controlled liquid fuel spray to the combustion test section where measurements of ignition energy have been made. The ignition studies were performed on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. Using the optimum electrode spacing and spark duration, the frequency of ignition was determined as a function of spark energy for three overall equivalence ratios (0.6, 0.8, and 1.0) and for initial droplet diameters of 25, 40, 50, 60, and 70 micro m.

Cernansky, N. P.↗
DOE OSTI2020

Potential Impacts of High-Octane Fuel Introduction in a Naturally Aspirated, Port Fuel-Injected Legacy Vehicle

In recent years there has been an increased interest in raising the octane level of gasoline to enable higher compression ratios (CR) in spark-ignition engines to improve vehicle fuel efficiency. A number of studies have examined opportunities to increase efficiency in future vehicles, but potential impacts on the legacy fleet have not received as much attention. In this study, our effort focused on experimental studies on an engine using high-octane fuels without changing the engine’s CR. Spark timing was advanced until maximum torque was reached or knock was encountered for each engine condition, using each individual fuel to maximize engine efficiency. Knock-limited conditions occurred as the output brake mean effective pressure (BMEP) neared the maximum attainable output at a given engine speed. Increasing research octane numbers generally enabled knock-free operation under a greater number of operating conditions. Vehicle modeling using Autonomie was used to project vehicle energy use, fuel economy, and tailpipe CO 2 emissions for the Urban Dynamometer Driving Schedule (UDDS), the Highway Fuel Economy Test (HWFET), and the US06 cycle. Results show that decreases in energy consumption of up to 2% for a small SUV are possible through the use of a 97 RON fuel compared to a baseline using 91 RON fuel, provided that the formulation of the fuel does not cause unanticipated operational issues such as lower maximum BMEP. Greater improvements using high-octane fuels are possible if the CR is increased, but there is no opportunity to increase the CR in legacy vehicles. Thus, these vehicles realize an improvement from increased octane rating in accordance with their ability to spark advance to take advantage of a fuel with a higher octane rating. For the modeled vehicle, improvements of up to 2% in volumetric fuel economy may be possible through the use of a 97 RON fuel with the largest gains expected on the US06 cycle. Fuel economy impacts are strongly coupled to the heating value of the fuels in addition to changes in engine efficiency. Similarly, decreases in tailpipe CO 2 emissions are also achievable. However, simultaneous improvements in energy consumption, fuel economy, and tailpipe CO 2 emissions are not guaranteed and are dependent upon fuel formulation.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS2005

Development of Ionic Liquid Monopropellants for In-Space Propulsion

A family of new, low toxicity, high energy monopropellants is currently being evaluated at NASA Marshall Space Flight Center for in-space rocket engine applications such as reaction control engines. These ionic liquid monopropellants, developed in recent years by the Air Force Research Laboratory, could offer system simplification, less in-flight thermal management, and reduced handling precautions, while increasing propellant energy density as compared to traditional storable in-space propellants such as hydrazine and nitrogen tetroxide. However, challenges exist in identifying ignition schemes for these ionic liquid monopropellants, which are known to burn at much hotter combustion temperatures compared to traditional monopropellants such as hydrazine. The high temperature combustion of these new monopropellants make the use of typical ignition catalyst beds prohibitive since the catalyst cannot withstand the elevated temperatures. Current research efforts are focused on monopropellant ignition and burn rate characterization, parameters that are important in the fundamental understanding of the monopropellant behavior and the eventual design of a thruster. Laboratory studies will be conducted using alternative ignition techniques such as laser-induced spark ignition and hot wire ignition. Ignition delay, defined as the time between the introduction of the ignition source and the first sign of light emission from a developing flame kernel, will be measured using Schlieren visualization. An optically-accessible liquid monopropellant burner, shown schematically in Figure 1 and similar in design to apparatuses used by other researchers to study solid and liquid monopropellants, will be used to determine propellant burn rate as a function of pressure and initial propellant temperature. The burn rate will be measured via high speed imaging through the chamber s windows.

Blevins, John A.↗
NASA NTRS2005

Development of Ionic Liquid Monopropellants for In-Space Propulsion

A family of new, low toxicity, high energy monopropellants is currently being evaluated at NASA Marshall Space Flight Center for in-space rocket engine applications such as reaction control engines. These ionic liquid monopropellants, developed in recent years by the Air Force Research Laboratory, could offer system simplification, less in-flight thermal management, and reduced handling precautions, while increasing propellant energy density as compared to traditional storable in-space propellants such as hydrazine and nitrogen tetroxide. However, challenges exist in identifying ignition schemes for these ionic liquid monopropellants, which are known to burn at much hotter combustion temperatures compared to traditional monopropellants such as hydrazine. The high temperature combustion of these new monopropellants make the use of typical ignition catalyst beds prohibitive since the catalyst cannot withstand the elevated temperatures. Current research efforts are focused on monopropellant ignition and burn rate characterization, parameters that are important in the fundamental understanding of the monopropellant behavior and the eventual design of a thruster. Laboratory studies will be conducted using alternative ignition techniques such as laser-induced spark ignition and hot wire ignition. Ignition delay, defined as the time between the introduction of the ignition source and the first sign of light emission from a developing flame kernel, will be measured using Schlieren visualization. An optically-accessible liquid monopropellant burner will be used to determine propellant burn rate as a function of pressure and initial propellant temperature. The burn rate will be measured via high speed imaging through the chamber s windows.

Blevins, John A.↗
DOE OSTI2024

Performance and Emissions of an SI Engine Fueled With DME-Propane Blends

Dimethyl Ether (DME) is an alternative fuel that can be produced renewably and has the potential for lower CO and NOx emissions than conventional petroleum-based fuels. Blending DME with another gaseous fuel such as propane, which has a lower knock tendency than gasoline, can allow this fuel to be leveraged on SI engines. In this study, the use of DME-propane blends on a spark ignition (SI) engine was studied via computer simulations in order to understand the impact on engine performance and emissions and to identify the knock limitations of using such fuel blends. A 2L Hyundai SI engine was modeled in GT Power and the model was validated by comparing it with computational fluid dynamics (CFD) simulation results. Starting from pure propane, DME was added incrementally until knock was observed in the engine. Results indicate that it is feasible to run propane with DME percentages up to 35% before severe knock impacts were observed. The BTE was higher, but the BSFC also increased for DME-propane blends as compared to gasoline. Here, an increase in NOx emissions was detected along with a significant decrease in CO emissions. CO 2 emissions declined for propane as compared to gasoline but increased with the addition of DME.

alternative fuels↗
DOE OSTI2020

Effects of molar expansion ratio of fuels on engine efficiency

Fuel properties have a strong impact on the efficiency of internal combustion engines. Contrary to other physical and thermochemical fuel properties, the molar expansion ratio is normally ignored. Molar expansion ratio is the ratio of number of moles of the products to the reactants. In this work, the impact of the fuel’s molar expansion ratio on engine efficiency is investigated. Findings are based on simulations of a spark ignition engine using different fuels (standard fuels and user-defined fuels) and different dilution ratios. Simulations without heat transfer and friction were performed first. The combustion then takes place at top dead center with a very short combustion duration to approach the ideal Otto cycle. The heat transfer and friction were then added step by step. From this analysis, it could be concluded that the heat loss and friction work decrease as molar expansion ratio increases. The gross indicated and brake thermal efficiencies thus increase. User-defined fuels with different molar expansion ratio, but the same physical and thermochemical properties were then employed. The simulated results showed that the brake thermal efficiency increases by around 1.15% with an increase in molar expansion ratio of 0.02 compared to a fuel with a molar expansion ratio of unity. Lastly, the simulation was also done with air and exhaust gas recirculation dilution.

42 ENGINEERING↗
DOE OSTI2022

Numerical and experimental investigation of the flame kernel growth in a methane/air mixture near the lean flammability limit

Lean combustion has the potential to improve the thermal efficiency of spark-ignition engines, but it faces the significant challenge of increased cycle-to-cycle variation due to low mixture reactivity and unstable flame dynamics. Computational fluid dynamics (CFD) employing predictive models can guide engine design and optimize operating strategies for lean combustion. However, ignition and combustion models have rarely been validated at fuel-lean conditions, and a fundamental understanding of the early flame kernel growth process is also lacking for a successful sub-model development. Here, the present study develops a numerical simulation framework used to investigate early flame kernel growth in methane/air mixtures. A nanosecond-pulsed discharge (NPD) approach is employed to effectively decouple the flame kernel growth from the electrical discharge due to their difference in timescales, and equivalence ratios near the experimentally measured lean flammability limit (LFL) are selected to focus on challenging mixture conditions. Three numerical investigations, such as the choice of turbulence modeling, grid size, and grid control strategies, are examined to match both LFL and flame kernel structure measured from experiments. It is demonstrated that a quasi-direct numerical simulation (QDNS) with a fixed grid embedding of 10 μm can predict the LFL as φ CFD =0.61 and match the displacement speed of the kernel’s boundary marked in schlieren images. To predict the LFL and flame kernel shape, a fine grid (Δ≤12.5 μm) is needed to capture the consumption of formaldehyde (CH 2 O) in kernel’s reaction branches attached to the anode, and adaptive mesh refinement is replaced with the fixed embedding due to loss of simulation accuracy. Also, it is found that a large-eddy simulation (LES) using the Dynamic Structure model is not suitable for the NPD-induced flame kernel simulation because artificial sub-grid turbulent kinetic energy induced by shock dynamics alters the flow velocity calculation, resulting in divergence of LES from QDNS. Lastly, the simulation well matches the experimental data for the flame kernel evolution in three mixture conditions (φ = 0.7, 0.61, 0.55), showing toroidal flame kernel expansion and flame kernel growth/extinction.

33 ADVANCED PROPULSION SYSTEMS↗