Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid oxide”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Investigation of SmBaCuCoO{sub 5+{delta}} double-perovskite as cathode for proton-conducting solid oxide fuel cells

SmBaCuCoO{sub 5+{delta}}, a double-perovskite oxide, was synthesized by the modified Pechini method and developed as cathode material for proton-conducting solid oxide fuel cells. The SmBaCuCoO{sub 5+{delta}} powders calcined at 800 {sup o}C, show the double-perovskite structure in powder XRD pattern. SmBaCuCoO{sub 5+{delta}} has a more suitable thermal expansion coefficient than SmBaCo{sub 2}O{sub 5+{delta}} for BaCe{sub 0.7}Zr{sub 0.1}Y{sub 0.2}O{sub 3-{delta}} electrolyte-based solid oxide fuel cells. The single cell was tested with humidified hydrogen ({approx}3% H{sub 2}O) as the fuel and static air as the oxidant. The performance of the cell was characterized by DC Electronic Load and AC impedance spectroscopy. The peak power densities reached 355-86 mW cm{sup -2} in the range of 700-550 {sup o}C and the interfacial polarization resistance decreased with increasing operation temperature, from 3.1 {Omega} cm{sup 2} at 550 {sup o}C to 0.22 {Omega} cm{sup 2} at 700 {sup o}C. The high power density and low polarization demonstrate that SmBaCuCoO{sub 5+{delta}} is a potential candidate for proton-conducting solid oxide fuel cells.

36 MATERIALS SCIENCE↗

Simple Electrolyzer Model Development for High-Temperature Electrolysis System Analysis Using Solid Oxide Electrolysis Cell

An electrolyzer model for the analysis of a hydrogen-production system using a solid oxide electrolysis cell (SOEC) has been developed, and the effects for principal parameters have been estimated by sensitivity studies based on the developed model. The main parameters considered are current density, area specific resistance, temperature, pressure, and molar fraction and flow rates in the inlet and outlet. Finally, a simple model for a high-temperature hydrogen-production system using the solid oxide electrolysis cell integrated with very high temperature reactors is estimated.

99 GENERAL AND MISCELLANEOUS↗

Progress in metal-supported solid oxide electrolysis cells: A review

There is increasing global interest in using solid oxide electrochemical cells to perform electrolysis. Metal-supported solid oxide electrolysis cells (MS-SOEC) are being developed with stainless steel and Ni-based supports. Additionally, the use of porous metal to support the electrochemically-active layers is anticipated to improve mechanical strength, decrease cost, and increase tolerance to aggressive operating conditions, including rapid thermal excursions. This review summarizes and analyzes the previous decade of progress in MS-SOEC development, and identifies critical needs for future work.

08 HYDROGEN↗

Control of Oxygen Delamination in Solid Oxide Electrolyzer Cells via Modifying Operational Regime

Possible modifications of operational regimes for solid oxide fuel cell (SOEC) devices for hydrogen production are discussed. It is shown that applying alternating current (AC) voltage pulses at a certain frequency range to SOECs could reduce oxygen delamination degradation in these devices and significantly increase their lifetime. This operational scheme provides wide possibilities to increase longevity of SOEC devices required for their use in commercial hydrogen production processes, without any significant modification of used materials and/or cell design. Developed simulation method possesses a broad generality and be employed in a number of other industrial processes.

08 HYDROGEN↗

Cerium-modified doped strontium titanate compositions for solid oxide fuel cell anodes and electrodes for other electrochemical devices

The present invention provides novel compositions that find advantageous use in making electrodes for electrochemical cells and electrochemical devices such as solid oxide fuel cells, electrolyzers, sensors, pumps and the like, the compositions comprising cerium-modified doped strontium titanate. The invention also provides novel methods for making and using anode material compositions and solid oxide fuel cells and solid oxide fuel cell assemblies having anodes comprising the compositions.

Marina, Olga A↗

Cerium-modified doped strontium titanate compositions for solid oxide fuel cell anodes and electrodes for other electrochemical devices

The present invention provides novel compositions that find advantageous use in making electrodes for electrochemical cells and electrochemical devices such as solid oxide fuel cells, electrolyzers, sensors, pumps and the like, the compositions comprising cerium-modified doped strontium titanate. The invention also provides novel methods for making and using anode material compositions and solid oxide fuel cells and solid oxide fuel cell assemblies having anodes comprising the compositions.

Marina, Olga A↗

Effect of Gd-doped ceria infiltration into Ni-YSZ on reversible solid oxide cell operation

Gadolinium doped ceria (GDC) infiltration into Ni-(Y 2 O 3 ) 0•08 (ZrO 2 ) 0.92 (Ni-YSZ) fuel electrodes has been shown to significantly improve solid oxide electrolysis cell performance and stability. However, the effects of GDC infiltration on cells operated reversibly between fuel cell and electrolysis modes have not been reported previously. Here we present reversible solid oxide cell life test results for different GDC infiltration loadings into Ni-YSZ electrodes in two types of fuel-electrode-supported solid oxide cells. Electrochemical impedance spectroscopy reveals that GDC infiltrant lowers the initial cell area specific resistance (ASR) and limits the degradation – for example, the GDC-infiltrated electrode ASR increased by 0.1 Ω cm 2 over 1000 h of reversible operation at ±0.5 A cm –2 and 800 °C, compared to 0.19 Ω cm 2 for non-infiltrated cells. Cell voltage degradation rates were reduced by infiltration during operation at a current density of ±0.5 A cm –2 at 800 °C, and during at 700 °C at ±0.75 A cm –2 . Furthermore, scanning electron microscopy observations show that the infiltrated GDC nanoparticles mitigate Ni particle coarsening in the Ni-YSZ electrode, possibly explaining the enhanced cell stability.

25 ENERGY STORAGE↗

Bipolar plate supported solid oxide fuel cell with a sealed anode compartment

A bipolar plate supported solid oxide fuel cell with a sealed anode compartment is provided. The solid oxide fuel cell includes a cathode, an electrolyte, and an anode, which are supported on a metallic bipolar plate assembly including gas flow fields and the gas impermeable bipolar plate. The electrolyte and anode are sealed into an anode compartment with a metal perimeter seal. An improved method of sealing is provided by extending the metal seal around the entire perimeter of the cell between an electrolyte and the bipolar plate to form the anode compartment. During a single-step high temperature sintering process the metal seal bonds to the edges of the electrolyte and anode layers, the metal foam flow field and the bipolar plate to form a gastight containment.

30 DIRECT ENERGY CONVERSION↗

Progress in durability of metal-supported solid oxide fuel cells with infiltrated electrodes

High power density and longevity are required to commercialize solid oxide fuel cells for vehicular applications. In this work, electrochemical durability of high-performance metal-supported solid oxide fuel cells (MS-SOFCs) with infiltrated catalysts is investigated. Durability screening of various cathode and anode compositions is conducted. The Pr 6 O 11 cathode and SDCN 40 (40 vol% Ni-60 vol% SDC) anode are selected due to preferential tradeoff between performance and durability. X-ray diffraction indicates the catalyst phases are stable after prolonged thermal annealing. Electrochemical impedance and scanning electron microscopy analyses show that the evolution of SDCN40 is minimal, and coarsening and Cr poisoning of the Pr 6 O 11 catalyst are the dominant degradation mechanisms. These degradation mechanisms are addressed by implementing three additional fabrication steps: (1) preoxidation of the metal support, (2) deposition of thin and protective atomic layer deposition (ALD) coatings throughout the cathode-side electrode and support, and (3) in situ pre-coarsening of the catalysts. A favorable tradeoff is achieved: the combination of the three fabrication steps reduces degradation rate at 0.7 V and 700 °C by two orders of magnitude to 2.3% kh -1 , while sacrificing 35% of initial power density. The catalyst pre-coarsening step is primarily responsible for the loss of performance.

25 ENERGY STORAGE↗

BaZn{sub 2}Si{sub 2}O{sub 7} and the solid solution series BaZn{sub 2−x}Co{sub x}Si{sub 2}O{sub 7} (0<x≤2) as high temperature seals for solid oxide fuel cells studied by high-temperature X-ray diffraction and dilatometry

For sealing of solid oxide fuel cells, glasses from which crystalline phases with high coefficient of thermal expansion (CTE) can be crystallized are required. In this paper, a new solid solution series BaZn{sub 2−x}Co{sub x}Si{sub 2}O{sub 7} (0<x≤2) is introduced which exhibit extremely high CTE. The prepared powders were characterized by X-ray diffraction and high-temperature X-ray diffraction (BaZn{sub 2}Si{sub 2}O{sub 7}). Sintered specimens were characterized by dilatometry. The introduction of Co{sup 2+} does not lead to a change in the space group. All compounds show a transition of a low to a high temperature modification. The attributed temperature increases from 300 °C for BaZn{sub 2}Si{sub 2}O{sub 7} to 850 °C for BaCo{sub 2}Si{sub 2}O{sub 7}. The volume expansion which runs parallel to the phase transition decreases with increasing cobalt concentration. The phase BaZn{sub 2}Si{sub 2}O{sub 7} shows the largest CTE and a steep volume effect during phase transition. For the compound BaZn{sub 0.25}Co{sub 1.75}Si{sub 2}O{sub 7} the CTE is minimum (8.6×10{sup −6} K{sup −1} (50–900 °C)) and increases again until for the compound BaCo{sub 2}Si{sub 2}O{sub 7} a CTE of 16.6×10{sup −6} K{sup −1} (50–900 °C) is reached. In the cobalt rich composition range, the CTEs are in the right range for high temperature fuel cells and can be adjusted by the composition. - Graphical abstract: The composition of the solid solution BaZn{sub 2−x}Co{sub x}Si{sub 2}O{sub 7} strongly affects the thermal expansion. Display Omitted - Highlights: • We examined the thermal expansion of solid solutions BaZn{sub 2−x}Co{sub x}Si{sub 2}O{sub 7} (0<x≤2). • BaZn{sub 2}Si{sub 2}O{sub 7} exhibits the highest thermal expansion due to a phase transition. • Substitution of small amounts of Zn{sup 2+} against Co{sup 2+} lead to decreasing thermal expansion. • The thermal expansions re-increased with further increasing Co{sup 2+} concentrations. • Seals based on these solid solutions should be suitable for solid oxide fuel cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rare Earth Nickelate Electrodes Containing Heavily Doped Ceria for Reversible Solid Oxide Fuel Cells

The electrochemical performance of composite rare-earth nickelate-rare-earth doped ceria oxygen electrodes, with a high level of rare-earth doping in ceria are reported. Additionally, the chemical stability of these compositions is reported at both the sintering (1240 ?C) and operating temperature (800 ?C). Specifically, a lanthanum nickelate La2NiO4+d (LNO) ?? 50 mol% lanthanum doped ceria (LDC50) oxygen electrode and a neodymium nickelate Nd2NiO4+d (NNO) ?? 50 mol% neodymium doped ceria (NDC50) oxygen electrode are tested in solid oxide fuel cell (SOFC) and solid oxide electrolysis cell (SOEC) modes and compared to a composite (La0.75Sr0.25)0.95MnO3±d (LSM)-8 mol% yttria stabilized zirconia (YSZ) electrode. The LNO–LDC50 oxygen electrode reaches a current density which is approximately three times that of the LSM-YSZ electrode in SOFC mode at 0.7 V and approximately two times the LSM-YSZ electrode at 1.2 V in SOEC mode. Similarly the NNONDC50 oxygen electrode reaches a current density which is approximately two times and approximately one and a half times that of LSM-YSZ at 0.7 V and 1.2 V respectively. Oxygen surface exchange results for LNO and NNO are also reported which show different oxygen exchange kinetics during oxidation versus reduction steps.

solid oxide electrolysis, solid oxide fuel cell (S↗

A highly oxygen reduction reaction active and CO 2 durable high-entropy cathode for solid oxide fuel cells

One big obstacle for the oxygen reduction reaction (ORR) electrode in solid oxide fuel cells (SOFCs) is the poor reaction activity and fast degradations caused by CO 2 poisoning. Here, in this study, we report our design of an active A-site Ca-rich high-entropy Pr 0.1875 Ba 0.1875 Sr 0.1875 La 0.1875 Ca 0.25 CoO 3-δ (PBSLC 25 C) electrode, guided by the O p-band theory. Here, when applied as a cathode in solid oxide fuel cells (SOFCs), it demonstrates high ORR activity and excellent CO 2 tolerance under realistic operating conditions. Ni-YSZ-based anode-supported cells with PBSLC 25 C cathodes demonstrate excellent peak power densities of 1.14 W cm -2 , 1.04 W cm -2 , and 0.77 W cm -2 in the air with 1%, 5%, and 10% CO 2 , respectively, at 750 °C. The engineered high-entropy PBSLC 25 C effectively diminishes the CO 2 poisoning effect and maintains active surfaces for fast oxygen exchange, as confirmed by the cell durability test in air containing CO 2 (5 and 10 vol%), Raman spectroscopy, and density functional theory calculations.

30 DIRECT ENERGY CONVERSION↗

Stack configurations for tubular solid oxide fuel cells

A fuel cell unit includes an array of solid oxide fuel cell tubes having porous metallic exterior surfaces, interior fuel cell layers, and interior surfaces, each of the tubes having at least one open end; and, at least one header in operable communication with the array of solid oxide fuel cell tubes for directing a first reactive gas into contact with the porous metallic exterior surfaces and for directing a second reactive gas into contact with the interior surfaces, the header further including at least one busbar disposed in electrical contact with at least one surface selected from the group consisting of the porous metallic exterior surfaces and the interior surfaces.

Armstrong, Timothy R↗

A highly active and Cr-resistant infiltrated cathode for practical solid oxide fuel cells

A critical obstacle to the commercialization of modern solid oxide fuel cells (SOFCs) loaded with metallic interconnects is the unacceptable degradation rate resulting from Cr (an element richly present in metallic interconnects) volatilization and its subsequent reaction with the cathode, forming insulating SrCrO 4 that blocks oxygen reduction reaction (ORR) active sites. Here we report a Cr-tolerant, yet ORR-active, cathode for sustainable operation of solid oxide fuel cells (SOFCs). The new resilient cathode consists of a continuous, nanoscaled, ORR-active SrCo 0.9 Ta 0.1 O 3–δ (SCT) as the capping layer and a commercial (La 0.6 Sr 0.4 ) 0.95 Co 0.2 Fe 0.8 O 3–δ (LSCF)–Ce 0.8 Gd 0.2 O 1.9 (GDC) composite as the underlying skeleton. Stability testing in a high-Cr-content environment shows that the cathode has a remarkable resistance to Cr-attack while retaining superior ORR activity. In conclusion, a successful implantation of this bilayer cathode into practical SOFC stacks will advance the commercialization of SOFC technology.

25 ENERGY STORAGE↗

Copper-substituted perovskite compositions for solid oxide fuel cell cathodes and oxygen reduction electrodes in other electrochemical devices

The present invention provides novel compositions that find advantageous use in making electrodes for electrochemical cells. Also provided are electrochemical devices that include active oxygen reduction electrodes, such as solid oxide fuel cells, sensors, pumps and the like. The compositions comprises a copper-substituted ferrite perovskite material. The invention also provides novel methods for making and using the electrode compositions and solid oxide fuel cells and solid oxide fuel cell assemblies having cathodes comprising the compositions.

25 ENERGY STORAGE↗

Strength and Fracture Toughness of Solid Oxide Fuel Cell Electrolyte Material Improved

Solid oxide fuel cells (SOFC) are being developed for various applications in the automobile, power-generation, and aeronautics industries. Recently, the NASA Glenn Research Center has been exploring the possibility of using SOFC's for aeropropulsion under its Zero Carbon Dioxide Emission Technology (ZCET) Program. 10-mol% yttriastabilized zirconia (10YSZ) is a very good anionic conductor at high temperatures and is, therefore, used as an oxygen solid electrolyte in SOFC. However, it has a high thermal expansion coefficient, low thermal shock resistance, low fracture toughness, and poor mechanical strength. For aeronautic applications, the thin ceramic electrolyte membrane of the SOFC needs to be strong and tough. Therefore, we have been investigating the possibility of enhancing the strength and fracture toughness of the 10YSZ electrolyte without degrading its electrical conductivity to an appreciable extent. We recently demonstrated that the addition of alumina to zirconia electrolyte increases its strength as well as its fracture toughness. Zirconia-alumina composites containing 0 to 30 mol% of alumina were fabricated by hot pressing. The hot pressing procedure was developed and various hot pressing parameters were optimized, resulting in dense, crackfree panels of composite materials. Cubic zirconia and a-alumina were the only phases detected, indicating that there was no chemical reaction between the constituents during hot pressing at elevated temperatures. Flexure strength sf and fracture toughness K(sub IC) of the various zirconia-alumina composites were measured at room temperature as well as at 1000 C in air. Both properties showed systematic improvement with increased alumina addition at room temperature and at 1000 C. Use of these modified electrolytes with improved strength and fracture toughness should prolong the life and enhance the performance of SOFC in aeronautics and other applications.

Bansal, Narottam P.↗