Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power switching”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High-Bandwidth Low-Inductance Current Shunt for Wide-Bandgap Devices Dynamic Characterization

High bandwidth sensors are required to measure the wide-bandgap devices' transient behavior because of their fast switching speed. In addition to high bandwidth, the current sensor must introduce little extra parasitic inductance to the switching power loop. The analysis of conventional shunt resistors shows the key to high bandwidth is the coaxial structure and its parasitic inductance is proportional to its transient heat energy rating. Additionally, by combining the structure of coaxial shunt resistor and alumina substrate surface mount thin film resistors, a novel surface mount coaxial shunt resistor is introduced. Experimental measurement verifies its capability of achieving very high bandwidth while introducing very low parasitic inductance. The design can achieve up to 2.23-GHz measurement bandwidth while keeping its parasitic inductance as low as 0.12 nH. Application in gallium nitride heterojunction-field-effect-transistors double pulse test shows it can faithfully capture the transient current waveform while introducing little interference to the switching behavior.

42 ENGINEERING↗
NASA NTRS1972

High voltage and current, gate assisted, turn-off thyristor development

An improved high speed power switch with unique turn-off capability was developed. This gate assisted turn-off thyristor (GATT) was rated 1000 volts and 100 amperes with turn-off times of 2 microseconds. Fifty units were delivered for evaluation. In addition, test circuits designed to relate to the series inverter application were built and demonstrated. In the course of this work it was determined that the basic device design is adequate to meet the static characteristics and dynamic turn-off specification. It was further determined that the turn-on specification is critically dependent on the gate drive circuit due to the distributive nature of the cathode-gate geometry. Future work should emphasize design modifications which reduce the gate current required for fast turn-on, thereby opening the way to higher power (current) devices.

Nowalk, T. P.↗
DOE OSTI2023

Sequential order dependent dark-exciton modulation in bi-layered TMD heterostructure

We report the emergence of dark-excitons in transition-metal-dichalcogenide (TMD) heterostructures that strongly rely on the stacking sequence, i.e., momentum-dark K-Q exciton located exclusively at the top layer of the heterostructure. The feature stems from band renormalization and is distinct from those of typical neutral excitons or trions, regardless of materials, substrates, and even homogeneous bilayers, which is further confirmed by scanning tunneling spectroscopy. To understand the unusual stacking sequence, we introduce the excitonic Elliot formula by imposing strain exclusively on the top layer that could be a consequence of the stacking process. We further find that the intensity ratio of Q- to K-excitons in the same layer is inversely proportional to laser power, unlike for conventional K-K excitons. This can be a metric for engineering the intensity of dark K-Q excitons in TMD heterostructures, which could be useful for optical power switches in solar panels.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Near-field infrared imaging of polar domain walls in Ni 3 TeO 6

Domain walls are leading platforms for the development of ultra-low power switching and memory devices due to their potential to be moved, created, and erased in real time and to mitigate heat flux. Interface vs wavelength size effects unfortunately preclude the measurement of phonons by traditional spectroscopic techniques, so it has been challenging to unravel the primary excitations of the lattice and the symmetries that they represent across these functional interfaces. In this work, we employ synchrotron-based near-field infrared nanospectroscopy to image polar domain walls in multiferroic Ni 3 TeO 6 . This is a unique platform because, in addition to hosting polar and chiral domains that are interlocked with one another, Ni 3 TeO 6 displays both charged and neutral interfaces depending upon the direction allowing the development of structure–property relations. From a local structure and a strain point of view, we find charged walls that are twice as wide as neutral walls as well as strong frequency shifts of vibrational modes across the charged walls. The near-field amplitude drops across the walls as well. We discuss these trends in terms of polarization and chirality as well as phonon lifetimes at functional interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Probabilistic Nanomagnetic Memories for Uncertain and Robust Machine Learning

This project evaluated the use of emerging spintronic memory devices for robust and efficient variational inference schemes. Variational inference (VI) schemes, which constrain the distribution for each weight to be a Gaussian distribution with a mean and standard deviation, are a tractable method for calculating posterior distributions of weights in a Bayesian neural network such that this neural network can also be trained using the powerful backpropagation algorithm. Our project focuses on domain-wall magnetic tunnel junctions (DW-MTJs), a powerful multi-functional spintronic synapse design that can achieve low power switching while also opening the pathway towards repeatable, analog operation using fabricated notches. Our initial efforts to employ DW-MTJs as an all-in-one stochastic synapse with both a mean and standard deviation didn’t end up meeting the quality metrics for hardware-friendly VI. In the future, new device stacks and methods for expressive anisotropy modification may make this idea still possible. However, as a fall back that immediately satisfies our requirements, we invented and detailed how the combination of a DW-MTJ synapse encoding the mean and a probabilistic Bayes-MTJ device, programmed via a ferroelectric or ionically modifiable layer, can robustly and expressively implement VI. This design includes a physics-informed small circuit model, that was scaled up to perform and demonstrate rigorous uncertainty quantification applications, up to and including small convolutional networks on a grayscale image classification task, and larger (Residual) networks implementing multi-channel image classification. Lastly, as these results and ideas all depend upon the idea of an inference application where weights (spintronic memory states) remain non-volatile, the retention of these synapses for the notched case was further interrogated. These investigations revealed and emphasized the importance of both notch geometry and anisotropy modification in order to further enhance the endurance of written spintronic states. In the near future, these results will be mapped to effective predictions for room temperature and elevated operation DW-MTJ memory retention, and experimentally verified when devices become available.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Schematic for the CAEN backup Power-supply [Slides]

J158 in the schematic shown below is the physical power switch for the UDCM. You will see that we really only care about 3 pins on this physical switch, pins 1,2 and 6. we are going to splice between the switch and the board, meaning we are ‘effectively’ elevating this component to become part of our own module, and then have our module interface with the board. So when I say ‘Pin 1 Switch’ I am literally referring the Switch’s pin 1. Whereas when I say ‘Pin 1 Board’ I am talking about the part of the board that originally would have interfaced with pin 1 on the switch as shown in the lower left corner.

42 ENGINEERING↗
DOE OSTI2024

Ultrasound preliminary cyber-physical evaluation

In this assessment, we focused on identifying unwanted RF emissions from the subject devices. This consisted of two major approaches: 1) Monitor for emitted RF during operation and ensure it is within expected bounds. 2) Inspect circuit board construction for any geometry or design patterns that could lead to RF emissions, whether intentional or unintentional. These patterns include: a) Single-ended PCB traces that could operate as an antenna. b) Insufficient shielding around typically “noisy” components such as switching power supplies. c) Free-hanging high-speed signal wires with no shielding that could emit RF. Suspicious components and design patterns were given a plausible reason to be included in the design. Any suspicious components or patterns warranted reason for deeper investigation. After more in-depth analysis no components were found to be intentionally malicious or had unexpected functionality.

42 ENGINEERING↗
NASA NTRS1970

Nondissipative optimum charge regulator

Optimum charge regulator provides constant level charge/discharge control of storage batteries. Basic power transfer and control is performed by solar panel coupled to battery through power switching circuit. Optimum controller senses battery current and modifies duty cycle of switching circuit to maximize current available to battery.

Rosen, R.↗
NASA NTRS1972

Development of high speed power thyristor: The gate assisted turn-off thyristor

A high speed power switch with unique turn-off capability was developed. This gate-assisted turn-off thyristor was rated at 609 V and 50 A with turn-off times of 2 microsec. Twenty-two units were delivered for evaluation in a series inverter circuit. In addition, test circuits designed to relate to the series inverter application were built and demonstrated.

Hamilton, D. R.↗
NASA NTRS1971

Regulated dc-to-dc converter for voltage step-up or step-down with input-output isolation.

A dc-to-dc regulated-converter circuit employing duty-cycle control with variable on and variable off time has been presented. A unique feature of this converter is the method by which the bistable-comparator output controls the duty cycle of the power switching transistor through the action of the encoder. The utilization of minor-loop flux excursions of a saturable-core transformer in the encoder makes it feasible to extend the converter switching frequency considerably higher than would normally be possible. With this converter circuit, high and very-high frequency converter operations were explored.

Feng, S. Y. M.↗
NASA NTRS1974

In-line task 57: Component evaluation

Design analysis tests were performed on selected power switching components to determine the possible applicability of off-the-shelf hardware to space shuttles. Various characteristics were also evaluated in those devices to determine the most desirable properties for the space shuttle.

Boykin, J. C.↗
NASA NTRS1980

An SCR inverter for electric vehicles

An inverter for an electric vehicle propulsion application has been designed and constructed to excite a polyphase induction motor from a fixed propulsion battery source. The inverter, rated at 35kW peak power, is fully regenerative and permits vehicle operation in both the forward and reverse directions. Thyristors are employed as the power switching devices arranged in a dc bus commutated topology. This paper describes the major role the controller plays in generating the motor excitation voltage and frequency to deliver performance similar to dc systems. Motoring efficiency test data for the controller are presented. It is concluded that an SCR inverter in conjunction with an ac induction motor is a viable alternative to present dc vehicle propulsion systems on the basis of performance and size criteria.

Latos, T.↗
NASA NTRS1983

Voltage Regulator for a dc-to-dc Converter

New voltage regulator isolates signals from power-switching converter without use of complex circuitry or optical couplers. Only addition is extra secondary winding on existing interstage transformer. Error signals shortcircuit new winding and inhibit converter action. Resistor in series with primary winding limits short-circuit current to prevent damage to circuit components. Extra transformer winding eliminates need for isolation components.

Mclyman, C. W.↗
NASA NTRS1981

Effect of weightlessness on lymphocyte proliferation

An experiment to study the effect of weightlessness on lymphocyte proliferation to detect possible alteration of the cells responsible for the immune response during long-duration space flights is described. Human lymphocytes in culture medium will be delivered shortly before launch in an incubator which will be kept at 37C. Mitogen will be added to the culture. A control without mitogen will be run in parallel. After 70 hours of incubation, radioactive thymidine will be added. After two hours, cellular activity will be stopped by fixation and incubator power switched off. Later, the amount of incorporated thymidine will be determined and the cell morphology and the distribution of cell organelles will be investigated.

Cogoli, A.↗
NASA NTRS1983

Analysis, testing, and evaluation of faulted and unfaulted Wye, Delta, and open Delta connected electromechanical actuators

Mathematical models capable of simulating the transient, steady state, and faulted performance characteristics of various brushless dc machine-PSA (power switching assembly) configurations were developed. These systems are intended for possible future use as primemovers in EMAs (electromechanical actuators) for flight control applications. These machine-PSA configurations include wye, delta, and open-delta connected systems. The research performed under this contract was initially broken down into the following six tasks: development of mathematical models for various machine-PSA configurations; experimental validation of the model for failure modes; experimental validation of the mathematical model for shorted turn-failure modes; tradeoff study; and documentation of results and methodology.

Nehl, T. W.↗
NASA NTRS1983

The electronic switching spherical array antenna for the Earth Radiation Budget Spacecraft

The ESSA is a microprocessor-controlled antenna for low orbiting spacecraft for telemetry and command relay through the Tracking and Data Relay Satellite System (TDRSS). The array is a hemispherical shape covered with disk radiating elements. A group of radiating elements are continuously selected by the microprocessor controller to form a beam in the direction of a TDRS. A radial switching power divider uses PIN diodes to select the desired radiating elements. The antenna gain is a function of the size of the hemispherical dome. A 30-inch diameter dome is presently being built for the Earth Radiation Budget Spacecraft (ERBS). Gain of this antenna over a hemisphere is 14 dBi and polarization is lefthand circular. There are 145 radiating elements with 12 being used at one time to form a beam. The ESSA subsystem weights 74 pounds and power consumption is 20 watts. RF power handling capability is 30 watts. The S-Band radiating elements have a 10 percent bandwidth that allows simultaneous transmission and reception.

Kudrna, K.↗