Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Low cost fabrication development for oxide dispersion strengthened alloy vanes

Viable processes were developed for secondary working of oxide dispersion strengthened (ODS) alloys to near-net shapes (NNS) for aircraft turbine vanes. These processes were shown capable of producing required microstructure and properties for vane applications. Material cost savings of 40 to 50% are projected for the NNS process over the current procedures which involve machining from rectangular bar. Additional machining cost savings are projected. Of three secondary working processes evaluated, directional forging and plate bending were determined to be viable NNS processes for ODS vanes. Directional forging was deemed most applicable to high pressure turbine (HPT) vanes with their large thickness variations while plate bending was determined to be most cost effective for low pressure turbine (LPT) vanes because of their limited thickness variations. Since the F101 LPT vane was selected for study in this program, development of plate bending was carried through to establishment of a preliminary process. Preparation of ODS alloy plate for bending was found to be a straight forward process using currently available bar stock, providing that the capability for reheating between roll passes is available. Advanced ODS-NiCrAl and ODS-FeCrAl alloys were utilized on this program. Workability of all alloys was adequate for directional forging and plate bending, but only the ODS-FeCrAl had adequate workability for shaped preform extrustion.

Perkins, R. J.↗
NASA NTRS1980

Effects of temperature, thermal exposure, and fatigue on an alumina/aluminum composite

An experimental investigation of the mechanical properties and microstructure of an aluminum matrix/polycrystalline alumina fiber composite material is discussed. The effects of fabrication, isothermal exposure (up to 10,000 hours at 590 K), thermal cycling (6000 cycles between 200 K and 590 K), fatigue (1,000,000 tension-tension cycles) were determined by mechanical testing and metallurgical analysis. The fabrication process severely degraded the fiber strength by reducing the alumina to a nonstoichiometric form and quenching in the resultant vacancies and stress fields. However, isothermal exposure, thermal cycling, and fatigue cycling all restored the fiber strength by enhancing vacancy annihilation. Comparison of the as-fabricated material with other aerospace materials shows that it is an attractive candidate for select applications. Long duration isothermal exposure weakened the matrix by overaging and through the diffusional loss of lithium to a surface reaction forming lithium carbonate. Thermal cycling initiated cracks in the matrix and fibers. Tension-tension fatigue cycling caused no apparent damage to the as-fabricated material but in fact, strengthened it to the rule-of-mixtures value. Fatigue cycling after thermal exposure did have a cumulative damage effect.

Olsen, G. C.↗
NASA NTRS1982

Effects of cobalt on structure, microchemistry and properties of a wrought nickel-base superalloy

The effect of cobalt on the basic mechanical properties and microstructure of wrought nickel-base superalloys has been investigated experimentally by systematically replacing cobalt by nickel in Udimet 700 (17 wt% Co) commonly used in gas turbine (jet engine) applications. It is shown that the room temperature tensile yield strength and tensile strength only slightly decrease in fine-grained (disk) alloys and are basically unaffected in coarse-grained (blading) alloys as cobalt is removed. Creep and stress rupture resistances at 760 C are found to be unaffected by cobalt level in the blading alloys and decrease sharply only when the cobalt level is reduced below 8 vol% in the disk alloys. The effect of cobalt is explained in terms of gamma prime strengthening kinetics.

Jarrett, R. N.↗
NASA NTRS1982

Fundamentals of ultrasonic NDE for microstructure/material property interrelations

Some fundamental aspects of ultrasonic nondestructive evaluation for material properties and microstructure assessment are given. Ultrasonic wave interaction concepts, some recent findings, and practical ramifications are illustrated. The concepts are discussed in nonmathematical, narrative form. Additional information can be found in the references cited herein.

A. Vary↗
NASA NTRS1983

Understanding the roles of the strategic element cobalt in nickel base superalloys

The United States imports over 90% of its cobalt, chromium, columbium, and tantalum, all key elements in high temperature nickel base superalloys for aircraft gas turbine disks and airfoils. Research progress in understanding the roles of cobalt and some possible substitutes effects on microstructure, mechanical properties, and environmental resistance of turbine alloys is discussed.

Stephens, J. R.↗
NASA NTRS1983

Sintering of reaction bonded silicon nitride

A process to produce sintered reaction-bonded Si3N4 (SRBSN) articles has been developed. This process consists of the addition of an appropriate sintering aid to reaction-bonded Si3N4 followed by sintering between 1780 and 2000 C, using an over pressure of nitrogen. The principal advantage of this process is the low sintering shrinkages of 5 to 10 percent. The properties and microstructure of two SRBSN systems sintered with MgO and Y2O3 additives are described and were found to be comparable to corresponding hot-pressed Si3N4 systems. Examples of applications of both systems are illustrated, demonstrating near net shape fabrication capability of the process.

Mangels, J. A.↗
NASA NTRS1984

Microstructure and orientation effects on properties of discontinuous silicon carbide/aluminum composites

Composite panels containing up to 40 vol % discontinuous silicon carbide SiC whisker, nodule, or particulate reinforcement in several aluminum matrices are commercially fabricated and the mechanical properties and microstructual characteristics are evaluated. The yield and tensile strengths and the ductility are controlled primarily by the matrix alloy, the temper condition, and the reinforcement content. Particulate and nodule reinforcements are as effective as whisker reinforcement. Increased ductility is attributed to purer, more uniform starting materials and to more mechanical working during fabrication. Comparing mechanical properties with those of other aluminum alloys shows that these low cost, lightweight composites demonstrate very good potential for application to aerospace structures.

Mcdanels, D. L.↗
NASA NTRS1984

Understanding the roles of the strategic element cobalt in nickel base superalloys

Research progress in understanding the effects of cobalt and some possible substitute on microstructure, mechanical properties, and environmental resistance of turbine alloys is discussed. The United States imports over 90 percent of its cobalt, chromium, tantalum and columbium, all key elements in high temperature nickel base superalloys for aircraft gas turbine disks and airfoils. NASA, through joint government/industry/university teams, undertook a long range research program aimed at reducing or eliminating these strategic elements by examining their basic roles in superalloys and identifying viable substitutes.

Stephens, J. B.↗
NASA NTRS1985

Constitutive Cyclic Deformation Behavior in Single-crystal and Directionally Solidified SSME High-pressure Fuel Turbopump Airfoil Materials

The major goal of the project is to correlate mechanical properties with microstructural deformation behavior and to develop models for constitutive response under a variety of monotonic and cyclic loading cycles, temperatures, strain levels, strain rates, and environments. Two alloys are being studied as candidate SSME turbine blade materials. The first is PWA 1480, which is a single-crystal alloy whose nominal composition is reported. The second alloy being studied is D.S. Mar-M 246 + Hf. This is a directionally solidified material, and its nominal composition is also reported. The major areas of interest for the two materials will be slightly different. The single-crystal alloy lends itself well to fundamental deformation studies, since resolved shear stresses on slip planes are all known and only one grain is present. The D.S. material presents an excellent opportunity to study the effects of slightly misaligned grains on deformation behavior. The two materials will be studied by using approximately the same test matrix, so a good degree of direct comparison will also be possible.

Milligan, W. W.↗
NASA NTRS1985

Diffusion welding of MA 6000 and a conventional nickel-base superalloy

A feasibility study of diffusion welding the oxide dispersion strengthened (ODS) alloy MA 6000 to itself and to conventional Ni-base superalloy Udimet 700 was conducted. Butt joints between MA 6000 pieces and lap joints between Udimet 700 and the ODS alloy were produced by hot pressing for 1.25 hr at temperatures ranging from 1000 to 1200 C (1832-2192 F) in vacuum. Following pressing, all weldments were heat treated and machined into mechanical property test specimens. While three different combinations of recrystallized and unrecrystallized MA 6000 butt joints were produced, the unrecrystallized to unrecrystallized joint was most successful as determined by mechanical properties and microstructural examination. Failure to weld the recrystallized material probably related to a lack of adequate deformation at the weld interface. While recrystallized MA 6000 could be diffusion welded to Udimet 700 in places, complete welding over the entire lap joint was not achieved, again due to the lack of sufficient deformation at the faying surfaces. Several methods are proposed to promote the intimate contact necessary for diffusion welding MA 6000 to itself and to superalloys.

Moore, T. J.↗
NASA NTRS1985

Fabrication of ceramic components for advanced gas turbine engines

The AGT101 ceramic gas turbine engine feasibility study has made use of the slip casting of silicon or silicon nitride powders to produce either reaction-bonded or sintered components such as turbine rotors, turbine shrouds, and inner and outer diffusers. Attention is given to the effects of processing parameters on the microstructure and properties of the finished components; the parameters encompass powder particle size distribution, casting slip viscosity, pH, and solid content fraction. The green slip cast components were consolidated by nitriding, sintering, or sinter/HIPping.

Liu, F.↗
NASA NTRS1987

Conventionally cast and forged copper alloy for high-heat-flux thrust chambers

The combustion chamber liner of the space shuttle main engine is made of NARloy-Z, a copper-silver-zirconium alloy. This alloy was produced by vacuum melting and vacuum centrifugal casting; a production method that is currently now available. Using conventional melting, casting, and forging methods, NASA has produced an alloy of the same composition called NASA-Z. This report compares the composition, microstructure, tensile properties, low-cycle fatigue life, and hot-firing life of these two materials. The results show that the materials have similar characteristics.

Kazaroff, John M.↗
NASA NTRS1987

Processing of laser formed SiC powder

Processing research was undertaken to demonstrate that superior SiC characteristics could be achieved through the use of ideal constituent powders and careful post-synthesis processing steps. Initial research developed the means to produce approximately 1000 A uniform diameter, nonagglomerated, spherical, high purity SiC powders. Accomplishing this goal required major revision of the particle formation and growth model from one based on classical nucleation and growth to one based on collision and coalescence of Si particles followed by their carburization. Dispersions based on pure organic solvents as well as steric stabilization were investigated. Test parts were made by the colloidal pressing technique; both liquid filtration and consolidation (rearrangement) stages were modeled. Green densities corresponding to a random close packed structure were achieved. After drying, parts were densified at temperatures ranging from 1800 to 2100 C. This research program accomplished all of its major objectives. Superior microstructures and properties were attained by using powders having ideal characteristics and special post-synthesis processing procedures.

Haggerty, J. S.↗
NASA NTRS1986

Characterization of hydrogen embrittlement in nickel base superalloy single crystals

In order to study the role of CMSX2 single crystal microstructure on the combined stress-hydrogen environment effects, hydrogen was introduced by cathodic charging. Concentration measurements were carried out to investigate the dependence of hydrogen solubility and trapping on microstructure. Mechanical properties were measured at room temperature on smooth tensile specimens as a function of heat treatment, crystal orientation and H charging conditions. SEM and TEM allow to study H induced cracks initiation and propagation. A large amount of hydrogen can be dissolved and trapped in CMSX2 single crystals when exposed to a high hydrogen fugacity environment. The strong H trapping evidenced in voids explains the predominant role of these defects as crack initiation sites. The strong detrimental effect of hydrogen on the material tenacity is discussed.

Chene, J.↗
NASA NTRS1988

Dispersion strengthened NiAl alloys produced by rapid solidification processing

Initial experimental results are presented concerning the relationship between microstructure and properties in rapidly solidified NiAl alloys whose melting point is of the order of 1900 K. When the dispersoid content of NiAl alloys is increased, the dispersoids begin to populate the grain boundaries, rendering them weak, so that failure must propagate intergranularly. It is concluded that NiAl alloys' strength can be significantly increased through dispersoid additions without sacrifice of high temperature ductility.

Jha, S. C.↗
NASA NTRS1988

Gravity and configurational energy induced microstructural changes in liquid phase sintering

Experiments were performed with W-Ni-Fe heavy alloys in order to measure the microstructural changes vs. position that occur in liquid-phase sintering under normal gravity. The experimentally observed segregation is less than the calculated equilibrium segregation due to the retarding effect from the rigid solid skeleton formed during sintering. These results improve understanding of microstructure, mechanical properties, component shape, and dimensional stability benefits that may be realized from low-gravity sintering.

Kipphut, C. M.↗
NASA NTRS1988

Dispersion strengthening of precipitation hardened Al-Cu-Mg alloys prepared by rapid solidification and mechanical alloying

Several Al-4Cu-1Mg-1.5Fe-0.75Ce alloys have been processed from either rapidly solidified or mechanically alloyed powder using various vacuum degassing parameters and consolidation techniques. Strengthening by the fine subgrains, grains, and the dispersoids individually or in combination is more effective when the alloys contain shearable precipitates; consequently, the strength of the alloys is higher in the naturally aged rather than the artificially aged condition. The strengths of the mechanically alloyed variants are greater than those produced from prealloyed powder. Properties and microstructural features of these dispersion strengthened alloys are discussed in regards to their processing histories.

Gilman, P. S.↗
NASA NTRS1990

Wave propagation in composite media and material characterization

Characteristics of wave propagation in an undamaged composite medium are influenced by many factors, the most important of which are: microstructure, constituent properties, interfaces, residual stress fields, and ply lay-ups. Measurements of wave velocities, attenuation, and dispersion provide a powerful tool for nondestructive evaluation of these properties. Recent developments are reviewed for modeling ultrasonic wave propagation in fiber and particle-reinforced composite media. Additionally, some modeling studies are reviewed for the effects of interfaces and layering on attenuation and dispersion. These studies indicate possible ways of characterizing material properties by ultrasonic means.

Datta, Subhendu K.↗