Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “measurement data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS2025

NAIRAS Version 3 Atmospheric Ionizing Radiation Validation: Comparisons to RaD-X Measurements

The Nowcast of Aerospace Ionizing RAdiation System (NAIRAS) model predicts dosimetric and radiative flux quantities for assessing human radiation exposure levels and radiation effects on flight electronic systems from the surface of the Earth to deep space. NAIRAS version 3 includes many updates and improvements to the model. In this paper, NAIRAS version 3 dosimetric quantities are compared to observations of the atmospheric radiation environment taken during the Radiation Dosimetry Experiment (RaD-X) flight campaign. The RaD-X campaign consisted of a high-altitude balloon flight, with altitudes up to 40 km, and four coordinated aircraft flights covering an altitude range from 6-20 km. The RaD-X measurement data from the different flight platforms were acquired in September 2015 and at nearly the same vertical cutoff rigidity (3-4 GV). High quality, flight-averaged measurement data were provided at seven altitudes, which correspond to regions of fundamentally different radiation transport and collisional interaction physics. The NAIRAS model agrees with the RaD-X measurements to within 30% over the entire altitude domain of the flight campaign (0-40 km), which is within the measurement uncertainty.

Christopher J Mertens↗
NASA NTRS1979

Tensile and flexural strength of non-graphitic superhybrid composites: Predictions and comparisons

Equations are presented and described which can be used to predict bounds on the tensile and flexural strengths of nongraphitic superhybrid (NGSH) composites. These equations are derived by taking into account the measured stress-strain behavior, the lamination residual stresses and the sequence of events leading to fracture. The required input for using these equations includes constituents, properties (elastic and strength), NGSH elastic properties, cure temperature, and ply stress influence coefficients. Results predicted by these equations are in reasonably good agreement with measured data for strength and for the apparent knees in the nonlinear stress-strain curve. The lower bound values are conservative compared to measured data. These equations are relatively simple and are suitable for use in the preliminary design and initial sizing of structural components made from NGSH composites.

Chamis, C. C.↗
NASA NTRS1979

Tensile and flexural strength of nongraphitic superhybrid composites - Predictions and comparisons

Equations are presented and described which can be used to predict bounds on the tensile and flexural strengths of nongraphitic superhybrid (NGSH) composites. These equations are derived by taking into account the measured stress-strain behavior, the lamination residual stresses and the sequence of events leading to fracture. The required input for using these equations includes constituent composites, elastic and strength properties, NGSH elastic properties, cure temperature, and ply stress influence coefficients. Results predicted by these equations are in reasonably good agreement with measured data for strength and for the apparent 'knees' in the nonlinear stress-strain curve. The lower bound values are conservative compared to measured data. These equations are relatively simple and should be suitable for use in the preliminary design and initial sizing of structural components made from NGSH composites.

Chamis, C. C.↗
NASA NTRS1977

A hybrid technique for spacecraft attitude interpolation with arbitrary attitude data gaps

An algorithm for obtaining sufficiently accurate estimates of a system parameter Y, given a data record of the parameter in which at arbitrary times no direct observations of Y exist, and describing the variance of these estimates, is proposed. The method provides estimates at all requested times, and the variance of the estimates is maintained as close to the variance of directly measured data as the quality of input information will allow. Three classes of information are used: (1) the measured data record of Y and the statistical extension of this record into time intervals of no direct measurement, obtained by a modification of standard autocorrelation techniques; (2) an a priori indicator of the behavior of Y; and (3) one or more indirect indicators of Y based on observation of other system parameters. The application of the algorithm to the SEASAT-A attitude determination under conditions of sensor field-of-view limitations and sun occultations is presented.

Treder, A. J.↗
NASA NTRS1990

Boundary-layer stability analysis of flight-measured transition data

Correlation of in-flight boundary-layer transition experiments with linear boundary-layer stability theory contributes both to the validation of the numerical methods as well as the analysis of the measured transition process. Transition results obtained in a recent flight experiment, in which the extent of laminar flow and the transition process on the wing of a business-jet fitted with an instrumented glove section were determined, are analyzed. The experiment was conducted at freestream Mach numbers from 0.55 to 0.82, chord Reynolds numbers from 10 to 20 x 10 to the 6th, and leading-edge sweep angles 17 deg to 20 deg. The growth of both Tollmien-Schlichting and crossflow instabilities are predicted using the e exp n method for several flight conditions and the calculated n-factors at transition onset are correlated. Comparison of the measured dominant boundary-layer disturbance frequencies and the predicted unstable frequencies shows fair agreement for several of the flight conditions studied.

Obara, Clifford J.↗
NASA NTRS1991

A simple, analytical, axisymmetric microburst model for downdraft estimation

A simple analytical microburst model was developed for use in estimating vertical winds from horizontal wind measurements. It is an axisymmetric, steady state model that uses shaping functions to satisfy the mass continuity equation and simulate boundary layer effects. The model is defined through four model variables: the radius and altitude of the maximum horizontal wind, a shaping function variable, and a scale factor. The model closely agrees with a high fidelity analytical model and measured data, particularily in the radial direction and at lower altitudes. At higher altitudes, the model tends to overestimate the wind magnitude relative to the measured data.

Vicroy, Dan D.↗
NASA NTRS1998

Characterization and Design of Digital Pointing Subsystem for Optical Communication Demonstrator

The Optical Communications Demonstrator (OCD) is a laboratory-based lasercom demonstration terminal designed to validate several key technologies, including beacon acquisition, high bandwidth tracking, precision bearn pointing, and point-ahead compensation functions. It has been under active development over the past few years. The instrument uses a CCD array detector for both spatial acquisition and high-bandwidth tracking, and a fiber coupled laser transmitter. The array detector tracking concept provides wide field-of-view acquisition and permits effective platform jitter compensation and point-ahead control using only one steering mirror. This paper describes the detailed design and characterization of the digital control loop system which includes the Fast Steering Mirror (FSM), the CCD image tracker, and the associated electronics. The objective is to improve the overall system performance using laboratory measured data. The. design of the digital control loop is based on a linear time invariant open loop model. The closed loop performance is predicted using the theoretical model. With the digital filter programmed into the OCD control software, data is collected to verify the predictions. This paper presents the results of the, system modeling and performance analysis. It has been shown that measurement data closely matches theoretical predictions. An important part of the laser communication experiment is the ability of FSM to track the laser beacon within the. required tolerances. The pointing must be maintained to an accuracy that is much smaller than the transmit signal beamwidth. For an earth orbit distance, the system must be able to track the receiving station to within a few microradians. The failure. to do so will result in a severely degraded system performance.

Racho, C.↗
NASA NTRS2006

Mars Aerobraking Spacecraft State Estimation by Processing Inertial Measurement Unit Data

Aerobraking is an efficient technique for orbit adjustment of planetary spacecraft, such as Magellan (Venus), Mars Global Surveyor, and Mars Odyssey. Determination of the vehicle state during the aerobraking phase has conventionally been performed using only radiometric tracking data prior to and following the atmospheric drag pass. This approach is sufficiently accurate and timely to meet current mission operational requirements; however, it is expensive in terms of ground support and leads to delayed results because ofthe need for post-drag pass data. This research presents a new approach to estimation of the vehicle state during the atmospheric pass that sequentially incorporates observations from an Inertial Measurement Unit (IMU) and models of the vehicle and environment. The approach, called Inertial Measurements for Aerobraking Navigation (IMAN), is shown to perform at a level comparable to the conventional methods in terms of navigation accuracy and superior to them in terms of availability of the results immediately after completion ofthe pass. Furthermore, the research shows that IMAN can be used to reliably predict subsequent periapsis times and locations over all aerobraking regimes. IMAN also yields accurate peak dynamic pressure and heating rates, critical for a successful corridor control strategy, comparable to navigation team reconstructed values. This research also provides the first instance of the utilization of the Unscented Kalman Filter for the purpose of estimating an actual spacecraft trajectory arc about another planet.

Unscented Kalman Filter↗
NASA NTRS1993

Optimization of actuator arrays for aircraft interior noise control

A numerical procedure for grouping actuators in order to reduce the number of degrees of freedom in an active noise control system is evaluated using experimental data. Piezoceramic actuators for reducing aircraft interior noise are arranged into groups using a nonlinear optimization routine and clustering algorithm. An actuator group is created when two or more actuators are driven with the same control input. This procedure is suitable for active control applications where actuators are already mounted on a structure. The feasibility of this technique is demonstrated using measured data from the aft cabin of a Douglas DC-9 fuselage. The measured data include transfer functions between 34 piezoceramic actuators and 29 interior microphones and microphone responses due to the primary noise produced by external speakers. Control inputs for the grouped actuators were calculated so that a cost function, defined as a quadratic pressure term and a penalty term, was a minimum. The measured transfer functions and microphone responses are checked by comparing calculated noise reductions with measured noise reductions for four frequencies. The grouping procedure is then used to determine actuator groups that improve overall interior noise reductions by 5.3 to 15 dB, compared to the baseline experimental configuration.

Cabell, R. H.↗
NASA NTRS1999

Measurement and Data Distribution for Microgravity Accelerations on the International Space Station

Two accelerometer systems will be available on the International Space Station to support microgravity payloads with information about the quasi-steady and vibratory acceleration environment of the research facilities. The Microgravity Acceleration Measurement System will record contributions to the quasi-steady microgravity environment, including the influences of aerodynamic drag, vehicle rotation, and venting effects. The Space Acceleration Measurement System-II will measure vibratory disturbances on-board due to vehicle, crew, and equipment disturbances. Due to the dynamic nature of the microgravity environment and its potential to influence sensitive experiments, NASA's Principal Investigator Microgravity Services project has initiated a plan through which the data from these instruments will be distributed to researchers in a timely and meaningful fashion. Beyond the obvious benefit of correlation between accelerations and the scientific phenomena being studied, such information is also useful for hardware developers who can gain qualitative and quantitative feedback about their facility acceleration output to station.

McPherson, Kevin↗
NASA NTRS1992

Possibilistic measurement and set statistics

Set-based statistics are necessary to generate possibility distributions from measured data. Methods by which physical measurements can generate statistical data on real intervals are considered, including the following: trials from multiple heterogeneous measurement devices rather than a single instrument at multiple times; classes of consistent intervals constructed from statistical data around a common point focus or interval core; and consonant intervals constructed from statistical data.

Joslyn, Cliff↗
NASA NTRS1984

Static jet noise test results of four 0.35 scale-model QCGAT mixer nozzles

As part of the NASA Quiet Clean General Aviation Turbofan (QCGAT) engine mixer-nozzle exhaust system program, static jet exhaust noise was recorded at microphone angles of 45 to 155 deg relative to the nozzle inlet for a conventional profile coaxial nozzle and three 12-lobed coaxial mixer nozzles. Both flows in all four nozzles are internally mixed before being discharged from a single exhaust nozzle. The conventional profile coaxial nozzle jet noise is compared to the current NASA Lewis coaxial jet noise prediction and after applying an adjustment to the predicted levels based on the ratio of the kinetic energy of the primary and secondary flows, the prediction is within a standard deviation of 0.9 dB of the measured data. The mass average (mixed flow) prediction is also compared to the noise data for the three mixer nozzles with a reasonably good fit after applying another kinetic energy ratio adjustment (standard deviation of 0.7 to 1.5 dB with the measured data). The tests included conditions for the full-scale engine at takeoff (T.O.), cutback (86% T.O.) and approach (67% T.O.).

Groesbeck, D. E.↗
NASA NTRS1992

Astronaut candidate strength measurement using the Cybex 2 and the LIDO Multi-Joint 2 dynamometers

The Anthropometry and Biomechanics Laboratory in the man-Systems division at NASA's Johnson Space Center has as one of its responsibilities the anthropometry and strength measurement data collection of astronaut candidates. The anthropometry data is used to ensure that the astronaut candidates are within the height restrictions for space vehicle and space suit design requirements, for example. The strength data is used to help detect abnormalities or isolate injuries to muscle groups that could jeopardize the astronauts safety. The Cybex II Dynamometer has been used for strength measurements from 1985 through 1991. The Cybex II was one of the first instruments of its kind to measure strength and similarity of muscle groups by isolating the specific joint of interest. In November 1991, a LIDO Multi-Joint II Dynamometer was purchased to upgrade the strength measurement data collection capability of the Anthropometry and Biomechanics Laboratory. The LIDO Multi-Joint II Dynamometer design offers several advantages over the Cybex II Dynamometer including a more sophisticated method of joint isolation and a more accurate and efficient computer based data collection system.

Carroll, Amy E.↗
NASA NTRS1993

Adaptive computations of flow around a delta wing with vortex breakdown

An adaptive unstructured mesh solution method for the three-dimensional Euler equations was used to simulate the flow around a sharp edged delta wing. Emphasis was on the breakdown of the leading edge vortex at high angle of attack. Large values of entropy, which indicate vortical regions of the flow, specified the region in which adaptation was performed. The aerodynamic normal force coefficients show excellent agreement with wind tunnel data measured by Jarrah, and demonstrate the importance of adaptation in obtaining an accurate solution. The pitching moment coefficient and the location of vortex breakdown are compared with experimental data measured by Hummel and Srinivasan, showing good agreement in cases in which vortex breakdown is located over the wing.

Modiano, David L.↗
NASA NTRS2020

An Algorithm for Hyperspectral Remote Sensing of Aerosols: 3. Application to the GEO-TASO Data in KORUS-AQ Field Campaign

This paper describes the third part of a series of investigations to develop algorithms for simultaneous retrieval of aerosol parameters and surface spectral reflectance from the data measured by GEOstationary Trace gas and Aerosol Sensor Optimization (GEO-TASO) instrument. Since the algorithm is designed for future hyperspectral and geostationary satellite sensors, such as Tropospheric Emissions: Monitoring of Pollution (TEMPO), it is applied to GEO-TASO data measured over the same area by different flights as part of the Korea-United Stated Air Quality Study (KORUS-AQ) field campaign in 2016. While GEO-TAOS has a spectral sampling interval of ~0.28 nm in the visible, its data is thinned through a band selection approach with consideration of atmospheric transmittance and different surface types, which yields 20 common spectral bands to be used by the algorithm. The algorithm starts with 4 common principal components (PCs) for surface spectral reflectance extracted from various spectral libraries, and the constraints of surface reflectance parameters and aerosol scattering models respectively from k- means clustering analysis of the Rayleigh-corrected GEO-TASO spectra and AERONET data. The algorithm then proceeds iteratively with an optimal estimation approach to update PCs and retrieve aerosol optical depth (AOD) until the best match between simulated and GEOS-TASO measured spectra is achieved. The spectral AODs are compared between those retrieved from GEO-TASO (x) and 7 AERONETS (y) in 440, 550, 550, 675 nm, respectively. The comparison reveals that iterative updates of surface spectral PCs (and so surface reflectance) yield significant enhancement in AOD retrievals, improving the mean linear fitting equations from y = 0.735x + 0.088 (without update of PCs) to y = 1.055x+ 0.01, and the Pearson correlation coefficient (𝑅𝑅2) from 0.54 to 0.76, respectively. Move case studies are need to further evaluate the algorithm for its application to TEMPO that carries a enhanced version of GEO-TASO instrument.

Tropospheric Emissions: Monitoring of Pollution (T↗
NASA NTRS2002

Turbulent Navier-Stokes Flow Analysis of an Advanced Semispan Diamond-Wing Model in Tunnel and Free Air at High-Lift Conditions

Turbulent Navier-Stokes computational results are presented for an advanced diamond wing semispan model at low-speed, high-lift conditions. The numerical results are obtained in support of a wind-tunnel test that was conducted in the National Transonic Facility at the NASA Langley Research Center. The model incorporated a generic fuselage and was mounted on the tunnel sidewall using a constant-width non-metric standoff. The computations were performed at to a nominal approach and landing flow conditions.The computed high-lift flow characteristics for the model in both the tunnel and in free-air environment are presented. The computed wing pressure distributions agreed well with the measured data and they both indicated a small effect due to the tunnel wall interference effects. However, the wall interference effects were found to be relatively more pronounced in the measured and the computed lift, drag and pitching moment. Although the magnitudes of the computed forces and moment were slightly off compared to the measured data, the increments due the wall interference effects were predicted reasonably well. The numerical results are also presented on the combined effects of the tunnel sidewall boundary layer and the standoff geometry on the fuselage forebody pressure distributions and the resulting impact on the configuration longitudinal aerodynamic characteristics.

Ghaffari, Farhad↗
NASA NTRSDate not supplied

NASA/ONERA Collaboration on Small Hovering Rotor Broadband Noise Prediction using Lattice-Boltzmann and Structured Navier-Stokes Solvers

This work compares two lattice-Boltzmann method solvers, PowerFLOW and ProLB, and two structured Navier-Stokes solvers, OVERFLOW2 and FAST, used by NASA and ONERA, respectively, for the broadband noise prediction of an ideally twisted rotor as part of Implementing Arrangement number FR-0685-0, ‘Comparing Computational Fluid Dynamics Solvers for Broadband Noise Prediction.’ Predicted results are evaluated against measured data from both smooth and rough blade sets acquired in the Small Hover Anechoic Chamber at the NASA Langley Research Center. Aerodynamic thrust predictions are seen to agree more favorably with the rough-blade measurements, whereas torque predictions agree better with the smooth-blade measurements. A tonal noise comparison shows better agreement to the measured data with the two structured Navier-Stokes solvers than with the two lattice-Boltzmann solvers, which is thought to be caused by the different geometric discretization associated with each solver paradigm. Broadband noise comparisons show that both lattice-Boltzmann method solvers trend well with the smooth-blade measurements, with the exception of an overprediction by ProLB between 4 kHz and 15 kHz. OVERFLOW2 is seen to capture the measured nondeterministic tonal content between 3 kHz and 8 kHz on a narrowband spectral basis and FAST agrees well with the rough blades on a one-third octave band basis.

Christopher S. Thurman↗
NASA NTRS1980

Spherical roller bearing analysis. SKF computer program SPHERBEAN. Volume 3: Program correlation with full scale hardware tests

The results of a series of full scale hardware tests comparing predictions of the SPHERBEAN computer program with measured data are presented. The SPHERBEAN program predicts the thermomechanical performance characteristics of high speed lubricated double row spherical roller bearings. The degree of correlation between performance predicted by SPHERBEAN and measured data is demonstrated. Experimental and calculated performance data is compared over a range in speed up to 19,400 rpm (0.8 MDN) under pure radial, pure axial, and combined loads.

Kleckner, R. J.↗