Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material toxicity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Development of aircraft lavatory compartments with improved fire resistance characteristics

The Boeing's participation in a NASA-funded program (FIREMEN) included developing materials for use as lavatory wall panels, sidewall panels, and ceiling panels possessing flammability, smoke, and toxicity (FS&T) characteristics superior to current materials of construction is described. A sandwich panel system is developed for improving FS&T characteristics and acceptable cost, processing requirements, aesthetic qualities, abrasion resistance, strain resistance, scuff resistance, and washability.

Anderson, R. A.↗
DOE OSTI2026

Testing of High S Matrix Glasses to Expand DFHLW Glass Compositional Ranges (Rev.1)

Gaps in glass composition-property data for direct-feed high-level waste (DFHLW) have recently been identified. One such gap is the region of high sulfur solubility since previous, pretreated, high-level wastes contained very little sulfur. Filling this data gap will significantly broaden the range of process flowsheet options including minimal washing and will allow for optimized waste loading in DFHLW glasses. This report summarizes the data collected during the characterization of the DFHLW High S Glass Matrix (HS24). A glass matrix of 50 glass compositions was developed to evenly cover the DFHLW composition region for high sulfur glass. Matrix glasses were designed to expand the composition region outside the current component concentration and property limits so as to reduce uncertainties at the limits. The 50 matrix glasses were fabricated and tested for properties important to the success of DFHLW vitrification including: compositions, canister centerline cooling (CCC) crystallinity and isothermal crystallinity, density, viscosity, electrical conductivity (EC), product consistency test (PCT) response, toxicity, and sulfate solubility. Melter materials corrosion testing is reported elsewhere. These glasses were intentionally designed to have high SO 3 solubilities (0.7 to 2.2 SO 3 wt%) in compositional regions that had not been previously explored. Forty-eight glasses showed the measured SO 3 content retained >80% of the target SO 3 and the densities of all the glasses ranged from 2.49 g·cm -3 to 2.74 g·cm -3 . While the model predicted nepheline formation in 5 glasses, one of the tested 50 CCC glasses formed nepheline, and 35 glasses formed Cr-containing phases such as spinels and eskolaite. Only five glasses were amorphous after CCC treatment where 44 glasses with detectable crystals contained =10 wt% crystals and only one glass had > 10 wt% crystals. None of the glasses exceeded the allowable T 2% for spinel crystal formation at 950 ºC (i.e., no glasses had >2 wt% spinel at 950 ºC) during isothermal crystal fraction tests where 10 glasses showed no crystalline phases at or below 950 ºC. All the glasses (except one which failed being slightly lower than the target) satisfied the SO 3 constraint while 98 glasses did not meet the viscosity constraints and 4 failed the EC constraints. Six quenched (Q) and six CCC glasses failed the Defense Waste Processing Facility (DWPF) Environmental Assessment (EA) glass PCT threshold and 3 Q and 4 CCC failed the PCT design constraint. One glass exceeded the WTP delisting limits for Cr via EPA Method 1311 (i.e., Toxicity Characteristic Leaching Procedure, TCLP). It should be emphasized that some of these glasses were specifically designed to approach or even exceed certain property constraints, as filling data gaps in these regions will provide the greatest benefit for future model development by improving accuracy and reducing uncertainties. These insights will ultimately support the development of more robust glass formulation strategies, enabling higher waste loading, reducing operational risks, and expanding the processing envelope.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Coal Fired Power Plant Configuration and Operation Impact on Plant Effluent Contaminants and Conditions

The primary objective of this project is to characterize coal contaminants in coal-fired power plant wastewater as a function of coal type, unit configurations, and unit operation profile with uncertainty analysis. This project was in response to the U.S. Department of Energy (DOE) Solicitation DE-FOA-0001842. The project duration was between September 01, 2018, and December 31, 2021 (no-cost extension filed, due to the Covid-19 pandemic restrictions, and approved). Field and lab test program was conducted with the main goal to characterize coal contaminants in coal-fired power plant wastewater as a function of coal type, unit configurations, and unit operation profile with uncertainty analysis. In this project, the team of Lehigh University (prime recipient) and Western Kentucky University identified two suitable Thermoelectric Power Plants (TTPs) firing bituminous and sub-bituminous coals respectively, designed test plans, and performed sample collection. Sampling included coal from each TTPs power generation units, Wet Flue Gas Desulfurization (WFGD) slurry material and waste-water samples taken from the outlet of the water treatment tank prior to discharge and other pertinent locations. Coal samples are dried, crushed, and pulverized according to the American Society for Testing and Materials (ASTM) methods. The prepared coal samples are analyzed for normal proximate and ultimate analysis tests in addition to the toxic metals and anions according to ASTM methods. The FGD slurry materials are analyzed for toxic metals and anions according to Electric Power Research Institute (EPRI) or Environmental Protection Agency (EPA) methods, as appropriate. The wastewater samples from the water treatment tank outlet are analyzed for toxic metals and anions according to EPA methods. The effluent species analyzed include mercury, arsenic, selenium, nitrate/nitrite, bromide, and chlorine. This project provided results of effluent conditions as a function of coal type, unit configuration, and unit operation profile, and identified the levels of uncertainty in the effluent results.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1997

New Approaches to Waterproofing of Space Shuttle Insulating Materials

Future reusable space vehicles will be in service much more frequently than current space shuttles. Therefore, rapid reconditioning of spacecraft will be required. Currently, the waterproofing of space shuttles after each re-entry takes 72 hours and requires substantial labor. In addition, the currently used waterproofing reagent, DiMethylEthoxySilane (DMES), is considered toxic, and ethanol fumes are released during its hydrolytic activation. Consequently, a long time period, which is not acceptable for future operations, is needed to ensure that 0 the excess volatile compounds are removed before further maintenance of the space vehicle can be performed. The objective of this project was to assist NASA Ames in finding improved waterproofing systems by identifying suitable waterproofing agents that can be applied by vapor phase deposition and will be less toxic, bond more rapidly to the insulation material surface, and potentially have higher thermal stability than the DMES system. Several approaches to achieve faster waterproofing with less toxicity were assessed using the following alternatives: Reactive volatile compounds that are rapidly deposited by chemical bonding at the surface and leave no toxic volatiles. Reactive reagents that are the least toxic. Nonvolatile reagents that are very reactive and bond strongly to the insulating material surface. Three specific types of potential reagents were chosen for evaluation in this project: 1. Volatile reagents with Si-Cl functional groups for vapor deposition 2. Volatile reagents with Si-H functional groups for vapor deposition 3. Nonvolatile oligomeric or polymeric reactive siloxanes that are assumed to have higher thermal stability and/or strong bonding to the insulating material. The chemistry involved in the project was targeted at the generation of intermediates having reactive Si-OH bonds for the formation of either volatile species or polymeric species that bond rapidly to the surface and also cure rapidly. We focused on two chemical reactions@-hydrolysis of Si-Cl bonds and catalytic dehydrocoupling of Si-H bonds.

Blum, Yigal D.↗
DOE OSTI2025

Enhancing the Infrared Emission from Silver Chalcogenide Quantum Dots Through Microcavity Coupling

Nanocrystals (NCs) appear as a promising platform for cost effective infrared optoelectronics, while offering a simplified coupling to the CMOS platform. However, this perspective is slowed down by toxicity concerns, the most effective materials being based on Pb and Hg. There is currently a large effort to bring forth new platforms that are active in the infrared with a reduced heavy metal content. Here, in this study, the focus is on silver chalcogenides, which, thanks to a combination of inter‐ and intraband transitions, is suited to cover both short and mid wave infrared ranges. However, this material being less mature, the achieved photoluminescence (PL) appears quite broad, which is problematic for device integration. Here, it is demonstrated that a strong control over the PL spectrum can be obtained through integration into a dielectric cavity that magnifies the electric field by a factor 20 and narrows the PL full width at half maximum down to 15 nm for an emission at telecom wavelength. The PL is also highly directional to avoid most waveguiding effects which is of utmost interest for enhancing the efficiency of NC‐based light emitting diodes.

infrared luminescence↗
DOE OSTI2025

Vibrational sum frequency generation spectroscopy reveals the inertness of chromium oxide (001) surfaces

Nanoengineered metal oxides such as Cr(III)-oxide (chromia) films have diverse potential applications in corrosion inhibition, remediation, energy generation, catalysis, data storage, and biological and environmental systems. Concerns about material degradation or oxidation to toxic chromate necessitate an understanding of chromia/aqueous interfaces, beginning with their hydroxylation and hydration behavior. Vibrational sum-frequency generation spectroscopy (vSFG) provides specific molecular-level information about water at the oxide/aqueous junction with high surface selectivity. To overcome the strong absorber problem typical of certain metal oxides in the UV–visible range during nonlinear optical studies, we employed molecular beam epitaxy to deposit transparent, epitaxial nanofilms of Cr 2 O 3 with (001) crystalline orientation on sapphire (Al 2 O 3 (001)) substrates, as confirmed by atomic force microscopy and X-ray diffraction. vSFG spectra of the air and water interfaces of the Cr 2 O 3 (001) films reveal hydroxyl features corresponding to both dissociated and molecular water on the surface. In contrast to the dangling hydroxyls found on the bare Al 2 O 3 (001) substrate, the hydroxyl groups on the deposited Cr 2 O 3 (001) nanofilm do not readily undergo isotopic H/D exchange when exposed to varying forms of D 2 O under ambient conditions. When considering the chemistries of the corresponding trivalent cations in aqueous solution, the finding is at variance with their similar acidities and proton exchange dynamics but consistent with markedly slower inner-sphere water ligand exchange of hexaquo Cr 3+ . This finding challenges the idea that proton and water exchange at the water/Cr₂O₃(001) interface are solely correlated, driven by the strength of metal-bridging oxygen bonds and surface hydroxyl distribution, without direct causation.

Boamah-Agyemang, Mavis D. [Pacific Northwest Natio↗
DOE OSTI2023

Self-assembled Seashell Like Coatings for Large Area Robust Debris Shields for Next Generation Pulsed Power Drivers

During this LDRD project, our team developed a technology which enables the fabrication of novel nanostructures replicating seashell – “nature’s toughest material”. The resulting coatings exhibit high thermal stability up to 1650°C, which exceeds the hardness of Spectra® by ~44%, as well as the compressive strength of aluminum by ~57%. Coatings made with this technology are stronger, environmentally friendly, more sustainable, and more versatile than other comparable materials. Beryllium wafers, the current, most favorable shielding material in terms of thermal and mechanical properties, are very toxic and cost hundreds of times more than the new material developed in this project. The coatings on silicon wafer and stainless steel, respectively, have been tested as ride-along on the Z machine and clearly outperform the bare substrate. Use of this technology will have a profound global impact for pulsed power and fusion energy development, debris mitigation for spacecraft and satellites, durability of drill bits used in deep well drilling and tunnel boring operations, thermal protection of aircraft and manned spacecraft, and various other thermal and mechanical protection applications.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Development and evaluation of a plasma jet flameholder for scramjets

The objective of the work reported herein was to explore the use of a continuous operation plasma torch as an ignitor and flameholder for scramjet combustion. This research was motivated by the desire to eliminate the use of pyrophoric or toxic ignition and/or combustion enhancement materials in operational aircraft or shipboard systems. The total temperatures and torch powers used to ignite/flamehold Mach 2 combustion with hydrogen, ethylene, ethane, and methane were determined. The minimum ignition total temperatures for the fuels tested were hydrogen - 1065 R (lowest test temperature); ethylene - 1500 R; ethane - 2000 R; methane - 2700 R. These temperatures were obtained while operating the torch at a nominal 2 kw net power. The torch was shown to be a good ignitor and flameholder in that both hydrogen and hydrocarbon fuels could be stabilized by the torch and would 'blow off' when the torch was extinguished. The effectiveness of the torch was very sensitive to relative fuel injection location. Best combustion resulted when fuel was injected both upstream and downstream of the torch. These results indicated that an adiabatic plasma torch operating at about 2 kw could be an effective ignitor and flameholder for high-speed combustion.

Northam, G. B.↗
NASA NTRS2004

Computational and Experimental Study of Energetic Materials in a Counterflow Microgravity Environment

Counterflow diffusion flames are studied for various fuels flowing against decomposition products from solid ammonium perchlorate (AP) pellets in order to obtain fundamental understanding of composite propellant flame structure and chemistry. We illustrate this approach through a combined experimental and numerical study of a fuel mixture consisting of C2H4 CO + H2, and C2H2 + C2H4 flowing against solid AP. For these particular AP-fuel systems, the resulting flame zone simulates the various flame structures that are ex+ to exist between reaction products from Ap crystals and a hydrocarbon binder. As in all our experimental studies, quantitative species and temperature profiles have been measured between the fuel exit and AP surface. Species measured included CN, NH, NO, OH, N2, CO2, CO, H2, CO, HCl, and H2O. Temperature was measured using a thermocouple at the exit, spontaneous Raman scattering measurements throughout the flame, OH rotational population distributions, and NO vibrational population distributions. The burning rate of AP was also measured as a function of strain rate, given by the separation distance between the AP surface and the gaseous hydrocarbon fuel tube exit plane. This distance was nominally set at 5 mm, although studies have been performed for variations in separation distance. The measured 12 scalars are compared with predictions from a detailed gas-phase kinetics model consisting of 86 species and 531 reactions. Model predictions are found to be in good agreement with experiment and illustrate the type of kinetic features that may be expected to occur in propellants when AP particle size distributions are varied. Furthermore, the results constitute the continued development of a necessary database and validation of a comprehensive model for studying more complex AP-solid fuel systems in microgravity. Exploratory studies have also been performed with liquid and solid fuels at normal gravity. Because of melting (and hence dripping) and deep thermal wave penetration into the liquid, these experiments were found feasible, but not used for obtaining quantitative data. Microgravity experiments are needed to eliminate the dripping and boiling phenomena of these systems at normal gravity. Microgravity tests in the NASA Glenn 2.2 second drop tower were performed (1) to demonstrate the feasibility of performing propellant experiments using the NASA Glenn microgravity facilities, (2) to develop the operational procedures for safe handing of the energetic materials and disposal of their toxic combustion by-products and (3) to obtain initial measurements of the AP burning rate and flame structure under microgravity conditions. Experiments were conducted on the CH4/AP system previously studied at normal gravity using a modified design of the counterflow burner and a NASA Glenn Pig Rig, i.e., one of the existing drop rigs for general-purpose usage. In these experiments, the AP burning rate was measured directly with a linear variable differential transducer (LVDT) and video imaging of the flame structure was recorded ignition was achieved by hot wires stretched across the AP surfaces. Initial drop tower combustion data show that with the same burner separation distance and flow conditions of the normal gravity experiments, the AP burning rate is approximately a factor of two lower. This difference is likely a result of radiation effects, but further tests with longer test times need to be conducted to verify that steady state conditions were achieved under microgravity conditions.

Takahashi, Fumiaki↗
DOE OSTI2023

Development, Characterization, and Testing of Solid-State Electrolytes for Batteries

Traditional liquid electrolytes used in lithium (Li) metal batteries (LMBs) have severe safety issues, poor power density, as well as thermal and electrochemical instability that prevents their scaling to newer applications, such as electric vehicles. Using sulfide-based solid-state electrolytes (SSEs) is a viable method to address many of the issues that plague LMBs. However, the key issue preventing the expansion of sulfide-based SSEs is an interplay between poor interfacial stability with the electrodes and massive external stack pressure required to maintain electrode-electrolyte contact. The need for extensive pressure requires large system-level (i.e., battery pack used in an electric vehicle) housing that causes a disconnect between performance at a smaller scale and actual application. Secondary prevention to sulfide-based SSE adoption are difficulties in manufacturing, as toxic deterioration occurs when these materials are exposed to humidity, as well as drastic reduction in SSE performance at low temperature. This work hypothesizes that unique interfacial designs of electrodes and the modification of the sulfide-based SSE will enable reduction of necessary external cell pressure, and therefore support the design of practical LMBs. This will be done through collaboration within Idaho National Laboratory (INL), where manufacturing practices will be parameterized to produce low defect, low porosity SSEs with slight modifications. Next, artificial interfaces will be produced on electrodes to observe the conformality and mass transport properties between the modified SSE and pre-treated anode. External pressure on Li-metal cells will also be parameterized to reduce interfacial impedance while a reduction in the pressure will allot reasonable housing design for larger scale applications. Focus on novelty in this work occurs by modifications to the solid-solid interfaces between electrolyte and electrode, done through doping of the electrolyte and production of artificial interfaces on the Li-metal anode. The modifications at these interfaces, in addition to modified external pressure could identify and address the poor interfacial impedance that hinders high performance SSEs. Fundamental understanding on how to reduce the key hindrances of all-solid-state batteries (ASSBs) will support the advancement for larger scale production and performance, of which will be held in perspective for future works. Beyond battery development, the knowledge gained from process control and defect analysis is applicable to other ceramic systems, such as nuclear fuel coatings and high temperature electrolyzers.

25 ENERGY STORAGE↗
DOE OSTI2023

Development, Characterization, and Testing of Solid-State Electrolytes for Batteries

Traditional liquid electrolytes used in lithium (Li) metal batteries (LMBs) have severe safety issues, poor power density, as well as thermal and electrochemical instability that prevents their scaling to newer applications, such as electric vehicles. Using sulfide-based solid-state electrolytes (SSEs) is a viable method to address many of the issues that plague LMBs. However, the key issue preventing the expansion of sulfide-based SSEs is an interplay between poor interfacial stability with the electrodes and massive external stack pressure required to maintain electrode-electrolyte contact. The need for extensive pressure requires large system-level (i.e., battery pack used in an electric vehicle) housing that causes a disconnect between performance at a smaller scale and actual application. Secondary prevention to sulfide-based SSE adoption are difficulties in manufacturing, as toxic deterioration occurs when these materials are exposed to humidity, as well as drastic reduction in SSE performance at low temperature. This work hypothesizes that unique interfacial designs of electrodes and the modification of the sulfide-based SSE will enable reduction of necessary external cell pressure, and therefore support the design of practical LMBs. This will be done through collaboration within Idaho National Laboratory (INL), where manufacturing practices will be parameterized to produce low defect, low porosity SSEs with slight modifications. Next, artificial interfaces will be produced on electrodes to observe the conformality and mass transport properties between the modified SSE and pre-treated anode. External pressure on Li-metal cells will also be parameterized to reduce interfacial impedance while a reduction in the pressure will allot reasonable housing design for larger scale applications. Focus on novelty in this work occurs by modifications to the solid-solid interfaces between electrolyte and electrode, done through doping of the electrolyte and production of artificial interfaces on the Li-metal anode. The modifications at these interfaces, in addition to modified external pressure could identify and address the poor interfacial impedance that hinders high performance SSEs. Fundamental understanding on how to reduce the key hindrances of all-solid-state batteries (ASSBs) will support the advancement for larger scale production and performance, of which will be held in perspective for future works. Beyond battery development, the knowledge gained from process control and defect analysis is applicable to other ceramic systems, such as nuclear fuel coatings and high temperature electrolyzers.

25 ENERGY STORAGE↗
DOE OSTI2022

Lithium Ion Cathode Materials Prepared Using Glycerol as Solvent and Reactant

Two different types of cathode materials were prepared using glycerol as a solvent and reactant. The LiMn1/3Ni1/3Co1/3O2 layered oxide cathode material was successfully synthesized with a shorter time of heat treatment of 8hr at 900°C. An appreciated capacity retention of 83.7% after 100 cycles with an initial discharge capacity of 177.1 mAh/g at 0.1C (discharge rate) has been achieved. Another cathode material with the formula of Li1.2 Mn0.51Ni0.145+xCo0.145-xO2 (x=0 (LR2), 0.0725 (LR1)), as a Li-rich cathode material, has been also successfully synthesized using glycerol. It was shown that LR1 discharge capacity was increased from 185 to 213 mAh/g after 20 cycles and ended up with 194.9 mAh/g after 60 cycles at 0.1C (discharge rate). This material shows an exceptional discharge capacity retention, lower toxic cobalt component, and lower production cost comparing with other Li-rich cathode materials. Detailed results of powder material synthesis, characterization, and battery testing will be presented to demonstrate that glycerol as a green solvent in the synthesis of battery materials.

25 ENERGY STORAGE↗
DOE OSTI2020

Hydrazone-Linked Heptazine Polymeric Carbon Nitrides for Synergistic Visible-Light-Driven Catalysis

Heptazine-based conjugated polymeric carbon nitrides (PCNs) are promising metal-free photocatalysts, yet their synthesis is challenging due to the electron-deficiency and insolubility of heptazine units. Indeed, heptazine-containing polymers have only been prepared through nucleophilic substitution with amines by using toxic cyameluric chloride as the starting material. Herein, we report the novel and environmentally friendly method for preparing heptazine-based mesoporous PCNs with hydrazone links formed through a simple Schiff base condensation of melem-NH 2 and aldehydes. Unlike cyameluric chloride, melem-NH 2 is non-toxic, stable, and can be readily obtained from melem and hydrazine in solution. We demonstrate that the hydrazone linkages and the heptazine units synergistically enhance the photocatalytic activity of PCNs in visible-light-driven aerobic oxidation of benzyl alcohol to benzaldehyde. In particular, the polymer constructed from melem-NH2 and p-phthalaldehyde shows 17 times more activity than graphitic carbon nitride (g-C 3 N 4 ).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

October 2025 Semiannual Composite Salt Waste Processing Facility Decontaminated Salt Solution Toxicity Characteristic Leaching Procedure Results

The aqueous waste from the Salt Waste Processing Facility is sampled semiannually for transfers to the Saltstone Disposal Facility. Salt solution is treated at the Saltstone Production Facility and disposed of in the Saltstone Disposal Facility. Per request of customer, X-TTR-Z-00027, Revision 0, one Saltstone Processing Facility Decontaminated Salt Solution and Z area premix material for the October 2025 semiannual Toxicity Characteristic Leaching Procedure sample. The sample contained 60:40 (by weight) of slag and fly ash (referred to as the “Cement-Free grout sample”). Results from the technical report support Task 2: ‘Grout Leaching Analyses’ of the Task Technical Request prepared by Savannah River Mission Completion. At 51 days cured, the Saltstone sample was collected and shipped to a certified laboratory for analysis using the Toxicity Characteristic Leaching Procedure. The October 2025 Semiannual Cement-Free grout sample met 61 79.268.48 requirements for a non-hazardous waste form with respect to the Resource Conservation and Recovery Act metals and Underlying Hazardous Constituents and met the Saltstone Production Facility Waste Acceptance Criteria that was in effect at the time of the sample collection at the Salt Waste Processing Facility.

Hsieh, Madison [Savannah River National Laboratory↗
DOE OSTI2020

Functional metal–organic frameworks as effective sensors of gases and volatile compounds

Developing efficient sensor materials with superior performance for selective, fast and sensitive detection of gases and volatile organic compounds (VOCs) is essential for human health and environmental protection, through monitoring indoor and outdoor air pollutions, managing industrial processes, controlling food quality and assisting early diagnosis of diseases. Metal–organic frameworks (MOFs) are a unique type of crystalline and porous solid material constructed from metal nodes (metal ions or clusters) and functional organic ligands. They have been investigated extensively for possible use as high performance sensors for the detection of many different gases and VOCs in recent years, due to their large surface area, tunable pore size, functionalizable sites and intriguing properties, such as electrical conductivity, magnetism, ferroelectricity, luminescence and chromism. The high porosity of MOFs allows them to interact strongly with various analytes, including gases and VOCs, thus resulting in easily measurable responses to different physicochemical parameters. Although much of the recent work on MOF-based luminescent sensors have been summarized in several excellent reviews (up to 2018), a comprehensive overview of these materials for sensing gases and VOCs based on chemiresistive, magnetic, ferroelectric, and colorimertic mechanisms is missing. In this review, we highlight the most recent progress in developing MOF sensing and switching materials with an emphasis on sensing mechanisms based on electricity, magnetism, ferroelectricity and chromism. We provide a comprehensive analysis on the MOF–analyte interactions in these processes, which play a key role in the sensing performance of the MOF-based sensors and switches. We discuss in detail possible applications of MOF-based sensing and switching materials in detecting oxygen, water vapor, toxic industrial gases (such as hydrogen sulfide, ammonia, sulfur dioxide, nitrous oxide, carbon oxides and carbon disulfide) and VOCs (such as aromatic and aliphatic hydrocarbons, ketones, alcohols, aldehydes, chlorinated hydrocarbons and N,N'-dimethylformamide). Altogether, this review serves as a timely source of information and provides insight for the future development of advanced MOF materials as next-generation gas and VOC sensors.

36 MATERIALS SCIENCE↗
DOE OSTI2022

January 2022 Semiannual Saltstone Toxicity Characteristic Leaching Procedure (TCLP) Results

The aqueous waste from Tank 50 (salt solution) is sampled semiannually for transfers to the Saltstone Production Facility (SPF). Salt solution is treated at SPF and disposed of in the Saltstone Disposal Facility (SDF). Per request of customer, X-TTR-Z-00025, Revision 0, two SDF waste form (saltstone) samples were prepared in the Savannah River National Laboratory (SRNL) from the Tank 50 Waste Acceptance Criteria (WAC) sample and Z-Area premix material for the January 2022 semiannual Toxicity Characteristic Leaching Procedure (TCLP) samples. One sample contained a Full Premix which included 10:45:45 (by weight) of cement, slag and fly ash. The second sample contained 60:40 (by weight) of slag and fly ash only referred to as the “Cement-Free grout sample.” Results from this technical report support Task 2: ‘Grout Leaching Analyses’ of the Task Technical Request (TTR) prepared by Savannah River Mission Completion (SRMC). After at least 28 days cured, a sample of each of the SDF waste forms was collected and shipped to a certified laboratory for analysis using the Toxicity Characteristic Leaching Procedure (TCLP). The January 2022 semiannual saltstone (Full Premix) and the Cement-Free grout samples met the South Carolina (SC) Code of Regulations for Hazardous Waste Management Regulations (HWMR) 61-79.261.24 and 61-79-268.48 requirements for a non-hazardous waste form with respect to Resource Conservation and Recovery Act (RCRA) metals and Underlying Hazardous Constituents (UHCs), and also met the SPF WAC that was in effect at the time of the tank sampling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

July 2022 Semiannual Saltstone Toxicity Characteristic Leaching Procedure (TCLP) Results

The aqueous waste from Tank 50 (salt solution) is sampled semiannually for transfers to the Saltstone Production Facility (SPF). Salt solution is treated at SPF and disposed of in the Salstone Disposal Facility (SDF). Per request of customer, X-TTR-Z-00025, Revision 0, two SDF waste form (salstone) samples were prepared in the Savannah River National Laboratory (SRNL) from the Tank 50 Waste Acceptance Criteria (WAC) sample and Z-Area premix material for the July 2022 Semiannual Toxicity Characteristic Leaching Procedure (TCLP) samples. One sample contained a Full Premix which included 10:45:45 (by weight) of cement, slag and fly ash. The second sample contained 60:40 (by weight) of slag and fly ash only referred to as the "Cement-Free grout sample." Results from this technical report support Task 2: 'Grout Leaching Analyses' of the Task Technical Request (TTR) prepared by Savannah River Mission Completion (SRMC). After at least 28 days cured, a sample of each of the SDF waste forms was collected and shipped to a certified laboratory for analysis using Toxicity Characteristic Leaching Procedure (TCLP). The July 2022 semiannual salstone (Full Premix) and the Cement-Free grout samples met the South Carolina (SC) Code of Regulations for Hazardous Waste Management Regulations (HWMR) 61-79.261.24 and 61-79-268.48 requirements for the non-hazardous waste form with respect to Resource Conservation and Recovery Act (RCRA) metals and Underlying Hazardous Constituents (UHCs), and also met the SPF WAC that was in effect at the time of the tank sampling.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗