Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “liquid oxygen”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Wear modes active in angular contact ball bearings operating in liquid oxygen environment of the Space Shuttle turbopumps

Extensive experimental investigation has been carried out on used flight bearings of the high pressure oxidizer turbopumps (HPOTP) of the space shuttle main engine (SSME) in order to determine the dominant wear modes, their extent, and causes. The paper presents the methodology, various surface analysis techniques used, results, and discussion. The mode largely responsible for premature bearing wear has been identified as adhesive/shear peeling of the upper layers of bearing balls and rings. This mode relies upon the mechanisms of scale formation, breakdown, and removal, all of which are greatly enhanced by the heavy oxidation environment of the HPOTP. Major causes of the high wear rates appear to be lubrication and cooling, both inadequate for the imposed conditions of operation. Numerous illustrations and evidence are provided.

Chase, Thaddeus J.↗
NASA NTRS1993

Liquid hydrogen and liquid oxygen feedline passive recirculation analysis

During the National Launch System design phase, a computer code (FEEDLINE) was written to analyze the feasibility of using passive recirculation propellant conditioning for the LH2 and LO2 feed systems. The FEEDLINE code was employed to provide temperature profiles to the STME design team. The team used the temperature profiles to determine if the required Space Transportation Main Engine net positive suction pressure was met. One desired outcome of the LH2 testing was to determine if modifications are required for the FEEDLINE code. The initial LN2 calibration tests indicate that the environmental heat into the system decreases with increasing heater input.

Holt, Kimberly A.↗
NASA NTRS1993

Liquid oxygen (LO2) propellant conditioning concept testing

Testing of a simplified LO2 propellant conditioning concept for future expendable launch vehicles is discussed. Four different concepts are being investigated: no-bleed, low-bleed, use of a recirculation line, and He bubbling. A full-scale test article, which is a facsimile of a propellant feed duct with an attached section to simulate heat input from an LO2 turbopump, is to be tested at the Cold Flow Facility of the Marshall Space Flight Center West Test Area. Work to date includes: design and fabrication of the test article, design of the test facility and initial fabrication, development of a test matrix and test procedures, initial predictions of test output, and heat leak calibration and heat exchanger tests on the test articles.

Perry, Gretchen L. E.↗
NASA NTRS1956

Theoretical performance of JP-4 fuel and liquid oxygen as a rocket propellant II : equilibrium composition

Data were calculated for equivalence ratios of 1 to 3, chamber pressures of 300 and 600 pounds per square inch absolute, and pressure ratios of 1 to 1500. Parameters included are specific impulse, combustion and exit temperature, molecular weight, characteristic velocity, coefficient of thrust, ratio of nozzle-exit area to throat area, specific heat at constant pressure, isentropic exponent, viscosity, and thermal conductivity. A correlation is given which permits determination of performance for a wide range of chamber pressures.

Huff, Vearl N↗
NASA NTRS1957

A Study of Injection Processes for Liquid Oxygen and Gaseous Hydrogen in a 200-pound-thrust Rocket Engine

Characteristic velocities of six single-element injectors that separately varied propellant spreading and mixing were measured over a range of oxidant-fuel weight ratios of 2 to 7. Hydrogen inlet temperature was -320 degrees F. Injectors that both mixed and spread the propellants had the highest characteristic-velocity efficiency. Spreading of either propellant produced about the same increment efficiency. The increase in efficiency due to mixing was relatively small. With similar injectors, oxygen-hydrogen required about 0.2 to 0.5 of the combustor volume of oxygen-heptane for the same efficiency.

Auble, Carmon M↗