Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “lifting line”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

The Effect of Lift-Drag Ratio and Speed on the Ability to Position a Gliding Aircraft for a Landing on a 5,000-Foot Runway

Flight tests were made to determine the capability of positioning a gliding airplane for a landing on a 5,000-foot runway with special reference to the gliding flight of a satellite vehicle of fixed configuration upon reentry into the earth's atmosphere. The lift-drag ratio and speed of the airplane in the glides were varied through as large a range as possible. The results showed a marked tendency to undershoot the runway when the lift-drag ratios were below certain values, depending upon the speed in the glide. A straight line dividing the successful approaches from the undershoots could be drawn through a lift-drag ratio of about 3 at 100 knots and through a lift-drag ratio of about 7 at 185 knots. Provision of a drag device would be very beneficial, particularly in reducing the tendency toward undershooting at the higher speeds.

Reeder, John P.↗
NASA NTRS1961

Low-Subsonic-Speed Static Stability of Right-Triangular-Pyramid and Half-Cone Lifting Reentry Configurations

An investigation has been made to determine the low-subsonic-speed static stability characteristics of several right-triangular-pyramid and half-cone configurations. Also studied were the effects of various modifications, such as base extensions, nose shape, nose incidence, and ridge-line shape. The investigation showed that, in general, the models had satisfactory longitudinal and lateral stability. The basic pyramid model and the conical ridge-line model with or without a rounded nose had almost identical longitudinal and lateral stability characteristics and lift-drag ratios. The lift-drag ratios of the cylindrical ridge-line and half-cone models were considerably lower than those of the conical ridge-line model. The addition of a 20 degree boattail to the models increased the lift-drag ratios but decreased the directional stability, whereas a streamwise base extension was more effective in increasing the lift-drag ratios and increased the directional stability.

Ware, George M.↗
NASA NTRS1998

Thermal Management Design for the X-33 Lifting Body

The X-33 Advantage Technology Demonstrator offers a rare and exciting opportunity in Thermal Protection System development. The experimental program incorporates the latest design innovation in re-useable, low life cycle cost, and highly dependable Thermal Protection materials and constructions into both ground based and flight test vehicle validations. The unique attributes of the X-33 demonstrator for design application validation for the full scale Reusable Launch Vehicle, (RLV), are represented by both the configuration of the stand-off aeroshell, and the extreme exposures of sub-orbital hypersonic re-entry simulation. There are several challenges of producing a sub-orbital prototype demonstrator of Single Stage to Orbit/Reusable Launch Vehicle (SSTO/RLV) operations. An aggressive schedule with budgetary constraints precludes the opportunity for an extensive verification and qualification program of vehicle flight hardware. However, taking advantage of off the shelf components with proven technologies reduces some of the requirements for additional testing. The effects of scale on thermal heating rates must also be taken into account during trajectory design and analysis. Described in this document are the unique Thermal Protection System (TPS) design opportunities that are available with the lifting body configuration of the X-33. The two principal objectives for the TPS are to shield the primary airframe structure from excessive thermal loads and to provide an aerodynamic mold line surface. With the relatively benign aeroheating capability of the lifting body, an integrated stand-off aeroshell design with minimal weight and reduced procurement and operational costs is allowed. This paper summarizes the design objectives of the X-33 TPS, the flight test requirements driven configuration, and design benefits. Comparisons are made of the X-33 flight profiles and Space Shuttle Orbiter, and lifting body Reusable Launch Vehicle aerothermal environments. The X-33 TPS is based on a design to cost configuration concept. Only RLV critical technologies are verified to conform to cost and schedule restrictions. The one-off prototype vehicle configuration has evolved to minimize the tooling costs by reducing the number of unique components. Low cost approaches such as a composite/blanket leeward aeroshell and the use of Shuttle technology are implemented where applicable. The success of the X-33 will overcome the ballistic re-entry TPS mindset. The X-33 TPS is tailored to an aircraft type mission while maintaining sufficient operational margins. The flight test program for the X-33 will demonstrate that TPS for the RLV is not simply a surface insulation but rather an integrated aeroshell system.

Bouslog, S.↗
NASA NTRS1982

Doppler-radar observation of the evolution of downdrafts in convective clouds

A detailed analysis of the 20 July 1977 thunderstorm complex which formed and evolve over the South Park region in Central Colorado is presented. The storm was extensively analyzed using multiple Doppler radar and surface mesonet data, developed within an environment having very weak wind shear. The storm owed its intensification to the strength of the downdraft, which was nearly coincident with the region where the cloud had grown. The noteworthy features of this storm were its motion to the right of the cloud-level winds, its multicellular nature and discrete propagation, its north-south orientation, and its relatively large storm size and high reflectivity factor (55 dBZ). This scenario accounts for the observed mesoscale and cloud-scale event. A line of convergence was generated at the interface between the easterly upslope winds and westerly winds. During stage II, the convergence line subsequently propagated down the slopes of the Mosquito Range, and was the main forcing mechanism for the development of updraft on the west flank of the storm. The formation of downdraft on the eastern side of updraft blacked surface inflow, and created a detectable gust front. As the original downdraft intensified, the accumulation of evaporatively-chilled air caused the intensification of the mesohigh, which likely destroyed the earlier convergence line and created a stronger convergence line to the east, which forced up-lifting of the moist, westerly inflow and caused the formation of updraft to the east. An organized downdraft circulation, apparently maintained by precipitation drag and evaporational cooling, was responsible in sustaining a well-defined gust front. The storm attained its highest intensity as a consequence of merging with a neighboring cloud. The interaction of downdrafts or gust fronts from two intense cells appeared to be the primary mechanism of this merging process as suggested by Simpson et al. (1980). The merging process coincided with more rain than occurred in unmerged echoes.

Motallebi, N.↗
NASA NTRS1987

Investigation of the vortex flap concept on a 75-deg sweep delta wing at supersonic speeds

An experimental investigation of the aerodynamic performance of vortex flaps on a 75-deg sweep delta wing has been conducted in the NASA Langley Unitary Plan Wind Tunnel at Mach numbers from 1.7 to 2.8. The sharp leading edge vortex flaps consisted of the outboard 30 percent of the local wing semispan. Flap deflections of 0, 5, 10, and 15 deg were investigated, for both a wing-alone and a wing-body configuration. The flaps were effective in reducing the drag across the lift-coefficient range. Integration of the upper surface pressure distributions showed that the suction pressures induced by the vortex on the flap were responsible for the drag reductions. At some lift conditions, the minimum drag condition permitted hinge line separation or vortex migration inboard of the hinge line. This result is in contrast to subsonic results, where optimum conditions call for no hinge line separation. The magnitude of the drag reduction due to flap deflection generally decreased as Mach number increased. The effect of a cylindrical forebody on the drag reduction due to flap deflection was minimal.

Covell, Peter F.↗
NASA NTRS1993

In-flight pressure distributions and skin-friction measurements on a subsonic transport high-lift wing section

Flight experiments are being conducted as part of a multiphased subsonic transport high-lift research program for correlation with wind-tunnel and computational results. The NASA Langley Transport Systems Research Vehicle (B737-100 aircraft) is used to obtain in-flight flow characteristics at full-scale Reynolds numbers to contribute to the understanding of 3-D high-lift, multi-element flows including attachment-line transition and relaminarization, confluent boundary-layer development, and flow separation characteristics. Flight test results of pressure distributions and skin friction measurements were obtained for a full-chord wing section including the slat, main-wing, and triple-slotted, Fowler flap elements. Test conditions included a range of flap deflections, chord Reynolds numbers (10 to 21 million), and Mach numbers (0.16 to 0.40). Pressure distributions were obtained at 144 chordwise locations of a wing section (53-percent wing span) using thin pressure belts over the slat, main-wing, and flap elements. Flow characteristics observed in the chordwise pressure distributions included leading-edge regions of high subsonic flows, leading-edge attachment-line locations, slat and main-wing cove-flow separation and reattachment, and trailing-edge flap separation. In addition to the pressure distributions, limited skin-friction measurements were made using Preston-tube probes. Preston-tube measurements on the slat upper surface suggested relaminarization of the turbulent flow introduced by the pressure belt on the slat leading-edge surface when the slat attachment line was laminar. Computational analysis of the in-flight pressure measurements using two-dimensional, viscous multielement methods modified with simple-sweep theory showed reasonable agreement. However, overprediction of the pressures on the flap elements suggests a need for better detailed measurements and improved modeling of confluent boundary layers as well as inclusion of three-dimensional viscous effects in the analysis.

Yip, Long P.↗
NASA NTRS2006

Developing Multilayer Thin Film Strain Sensors With High Thermal Stability

A multilayer thin film strain sensor for large temperature range use is under development using a reactively-sputtered process. The sensor is capable of being fabricated in fine line widths utilizing the sacrificial-layer lift-off process that is used for micro-fabricated noble-metal sensors. Tantalum nitride films were optimized using reactive sputtering with an unbalanced magnetron source. A first approximation model of multilayer resistance and temperature coefficient of resistance was used to set the film thicknesses in the multilayer film sensor. Two multifunctional sensors were fabricated using multilayered films of tantalum nitride and palladium chromium, and tested for low temperature resistivity, TCR and strain response. The low temperature coefficient of resistance of the films will result in improved stability in thin film sensors for low to high temperature use.

Wrbanek, John D.↗
NASA NTRS2016

Expanding the Natural Laminar Flow Boundary for Supersonic Transports

A computational design and analysis methodology is being developed to design a vehicle that can support significant regions of natural laminar flow (NLF) at supersonic flight conditions. The methodology is built in the CDISC design module to be used in this paper with the flow solvers Cart3D and USM3D, and the transition prediction modules BLSTA3D and LASTRAC. The NLF design technique prescribes a target pressure distribution for an existing geometry based on relationships between modal instability wave growth and pressure gradients. The modal instability wave growths (both on- and off-axes crossflow and Tollmien-Schlichting) are balanced to produce a pressure distribution that will have a theoretical maximum NLF region for a given streamwise wing station. An example application is presented showing the methodology on a generic supersonic transport wingbody configuration. The configuration has been successfully redesigned to support significant regions of NLF (approximately 40% of the wing upper surface by surface area). Computational analysis predicts NLF with transition Reynolds numbers (ReT) as high as 36 million with 72 degrees of leading-edge sweep (ΛLE), significantly expanding the current boundary of ReT - ΛLE combinations for NLF. This NLF geometry provides a total drag savings of 4.3 counts compared to the baseline wing-body configuration (approximately 5% of total drag). Off-design evaluations at near-cruise and low-speed, high-lift conditions are discussed, as well as attachment line contamination/transition concerns. This computational NLF design effort is a part of an ongoing cooperative agreement between NASA and JAXA researchers.

Lynde, Michelle N.↗
NASA NTRS1972

Effect of configuration modification on the hypersonic aerodynamic characteristics of a blended delta wing-body entry vehicle

The longitudinal, lateral, and directional aerodynamic characteristics of a delta-wing configuration were obtained experimentally at Mach 20 in helium with Reynolds numbers, based on model length, of 1.5 million and 2.9 million and at a Mach number of 6 in air with a Reynolds number, based on model length, of 4.8 million. The angles of attack varied from 0 deg to 55 deg for two sideslip angles. The effects of the addition of dorsal fins, the removal of wing tip fins, an increase in elevon span, and changes in elevon hinge-line sweep angle are discussed. The unmodified vehicle had a maximum lift-drag ratio of 2.1 at Mach 19 and of 2.4 at Mach 6 with about the same lateral and directional stability level at both Mach numbers. As the Mach number increased from 6 to 20, the longitudinal center of pressure moved forward and more positive elevon deflection was therefore required to maintain a given trim angle. The removal of wing tip fins increased the maximum lift-drag ratio and had a negligible effect on longitudinal stability, but caused directional instability that was not corrected by the dorsal fins examined. The shape of the wing and elevon hinge-line sweep had a large influence on the induced yawing moment due to roll control.

Arrington, J. P.↗
DOE OSTI2025

Unsteady aerodynamic loads on pitching aerofoils represented by Gaussian body force distributions

The actuator line model (ALM) is an approach commonly used to represent lifting and dragging devices like wings and blades in large-eddy simulations (LES). The crux of the ALM is the projection of the actuator point forces onto the LES grid by means of a Gaussian regularisation kernel. The minimum width of the kernel is constrained by the grid size; however, for most practical applications like LES of wind turbines, this value is an order of magnitude larger than the optimal value that maximises accuracy. This discrepancy motivated the development of corrections for the actuator line, which, however, neglect the effect of unsteady spanwise shed vorticity. In this work we develop a model for the impact of spanwise shed vorticity on the unsteady loading of an aerofoil modelled as a Gaussian body force distribution, where the model is applicable within the regime of unsteady attached flow. The model solution is derived both in the time and frequency domain and features an explicit dependence on the Gaussian kernel width. We verify the model with ALM-LES for both pitch steps and periodic pitching. The model solution is compared with Theodorsen theory and validated with both computational fluid dynamics using body fitted grids and experiment. It is concluded that the optimal kernel width for unsteady aerodynamics is approximately 40 % of the chord. The ALM is able to predict the magnitude of the unsteady loading up to a reduced frequency of 𝑘 ≈ 0.2.

17 WIND ENERGY↗
NASA NTRS1992

Supersonic airplane design optimization method for aerodynamic performance and low sonic boom

This paper presents a new methodology for the optimization of supersonic airplane designs to meet the dual design objectives of low sonic boom and high aerodynamic performance. Two sets of design parameters are used on an existing High Speed Civil Transport (HSCT) configuration to maximize the aerodynamic performance and minimize the sonic boom under the flight track. One set of the parameters perturbs the camber line of the wing sections to maximize the lift-over-drag ratio (L/D). A preliminary optimization run yielded a 3.75 percent improvement in L/D over a baseline low-boom configuration. The other set of parameters modifies the fuselage area to achieve a target F-function. Starting from an initial configuration with strong bow, wing, and tail shocks, a modified design with a flat-top signature is obtained. The methods presented can easily incorporate other design variables and objective functions. Extensions to the present capability in progress are described.

Cheung, Samson H.↗
NASA NTRS1994

Cryocooler Coldfinger Heat Interceptor

Spacecraft instruments requiring cryocoolers in their design struggle to keep overall power requirements in line with feasible solar array dimensions and launch vehicle lift capacities. Intermediate temperature (150 K to 200 K) radiators to cool radiation shields or optics on spacecraft instruments provide an as yet untapped resource for reducing the cryocooler power requirments.

Cryogenic Temperature↗
DOE OSTI2022

Nonsymmorphic symmetry-protected band crossings in a square-net metal PtPb 4

Topological semimetals with symmetry-protected band crossings have emerged as a rich landscape to explore intriguing electronic phenomena. Nonsymmorphic symmetries in particular have been shown to play an important role in protecting the crossings along a line (rather than a point) in momentum space. Here we report experimental and theoretical evidence for Dirac nodal line crossings along the Brillouin zone boundaries in PtPb 4 , arising from the nonsymmorphic symmetry of its crystal structure. Interestingly, while the nodal lines would remain gapless in the absence of spin–orbit coupling (SOC), the SOC, in this case, plays a detrimental role to topology by lifting the band degeneracy everywhere except at a set of isolated points. Nevertheless, the nodal line is observed to have a bandwidth much smaller than that found in density functional theory (DFT). Our findings reveal PtPb 4 to be a material system with narrow crossings approximately protected by nonsymmorphic crystalline symmetries.

36 MATERIALS SCIENCE↗
NASA NTRS1961

Heat-Transfer Measurements at a Mach Number of 4.95 on Two 60 deg Swept Delta Wings with Blunt Leading Edges and Dihedral Angles of 0 deg and 45 deg

An experimental investigation was conducted to evaluate the heat-transfer characteristics of two 60 deg swept delta wings with cylindrical leading edges of 0.25-inch radii and dihedral angles of 0 deg and 45 deg. The tests were conducted at a Mach number of 4.95 and a stagnation temperature of 400 F. The The test-section unit Reynolds number was varied from 1.95 x 10(exp 6) to 12.24 x 10(exp 6) per foot. The results of the investigation indicated that, in a plane normal to the leading edge, the laminar-flow heat-transfer distribution was in good agreement with two-dimensional blunt-body theory. The stagnation-line heat-transfer level could be predicted from two-dimensional blunt-body theory provided the stagnation-line heat-transfer coefficient was assumed to vary as the cosine of the effective sweep. A comparison of the heating rates to the 0 deg dihedral wing (planform sweep of 60 deg) and the 45 deg dihedral wing (planform sweep of 69.3 deg) with equal panel sweep and panel area indicated that the stagnation-line heat-transfer coefficient for the 45 deg dihedral wing could be as much as 40 percent less than the stagnation-line heat-transfer coefficient for the 0 deg dihedral wing at both equal angles of attack and equal lifts. The laminar-flow heat-transfer rate to both wings outside the vicinity of the stagnation line was essentially equal.

Stainback, P. Calvin↗
NASA NTRS1976

Distributed upper-surface blowing concept

A low speed investigation was conducted in the Langley V/STOL tunnel to determine the powered lift aerodynamic performance of a distributed upper surface blown propulsive lift transport model. The model used blowing slots across the span of the wing to produce a thin jet efflux near the leading edge and at the knee of the trailing edge flap (internally blown jet flap). Results indicate that these concepts have both good propulsive related lift and low drag due to lift characteristics because of uniform spanwise propulsive thrust. The leading edge blowing concept provides low speed lift characteristics which are competitive with the flap-hinge-line blowing concept and does not require additional leading edge treatment for prevention of abrupt stall.

Fournier, P. G.↗
NASA NTRS1980

High density circuit technology

Acquisition of polyimide materials for inter-metal dielectrics was obtained from three vendors, with considerable evaluation conducted on the Dupont PI2550 material. Experimental results indicate this material can be patterned using contact printing to line width far below 0.1 mils. Optimum line width is acquired using plasma etch equipment. Metal lift-off experiments on thermal evaporated films were optimized for application to sputtered deposited films. Alternate metal-lift-off experiments are proposed for future investigation. Dry processing equipment studies and future trends in VLSI fabrication techniques are on-going.

Wade, T. E.↗
NASA NTRS2014

An Experimental and Computational Study on Soot Formation in a Coflow Jet Flame Under Microgravity and Normal Gravity

Upon the completion of the Structure and Liftoff in Combustion Experiment (SLICE) in March 2012, a comprehensive and unique set of microgravity coflow diffusion flame data was obtained. This data covers a range of conditions from weak flames near extinction to strong, highly sooting flames, and enabled the study of gravitational effects on phenomena such as liftoff, blowout and soot formation. The microgravity experiment was carried out in the Microgravity Science Glovebox (MSG) on board the International Space Station (ISS), while the normal gravity experiment was performed at Yale utilizing a copy of the flight hardware. Computational simulations of microgravity and normal gravity flames were also carried out to facilitate understanding of the experimental observations. This paper focuses on the different sooting behaviors of CH4 coflow jet flames in microgravity and normal gravity. The unique set of data serves as an excellent test case for developing more accurate computational models.Experimentally, the flame shape and size, lift-off height, and soot temperature were determined from line-of-sight flame emission images taken with a color digital camera. Soot volume fraction was determined by performing an absolute light calibration using the incandescence from a flame-heated thermocouple. Computationally, the MC-Smooth vorticity-velocity formulation was employed to describe the chemically reacting flow, and the soot evolution was modeled by the sectional aerosol equations. The governing equations and boundary conditions were discretized on an axisymmetric computational domain by finite differences, and the resulting system of fully coupled, highly nonlinear equations was solved by a damped, modified Newtons method. The microgravity sooting flames were found to have lower soot temperatures and higher volume fraction than their normal gravity counterparts. The soot distribution tends to shift from the centerline of the flame to the wings from normal gravity to microgravity.

microgravity↗
NASA NTRS1951

Investigation of the Effects of Twist and Camber on the Aerodynamic Characteristics of a 50 Degrees 38 Minutes Sweptback Wing of Aspect Ratio 2.98 : Transonic-bump Method

An investigation of two semispan wings swept back 50 degrees 38 minutes was conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.68 to 1.15 by use of the transonic-bump technique. This paper presents the results of the investigation of wing-alone and wing-fuselage configurations of the two wings; one was an untwisted uncambered wing and the other was the same wing but incorporated twist and camber designed to give uniform load at a lift coefficient of 0.25 at a Mach number of 1.10. The semispan wings had their quarter-chord lines swept back 50 degrees 38 minutes, aspect ratios 2.98, taper ratios 0.45, and modified NACA 64A-series airfoil sections tapered in thickness. Lift, pitching moment, drag, and bending moment were obtained for these configurations.

WINGS, COMPLETE - DESIGN VARIABLES↗