SEARCH · Engineering Papers

Results for “interfacial engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

All sources NASA NTRS DOE OSTI

DOE OSTI2023

SA508 low alloy steel to 316L stainless steel dissimilar metal joint made by powder metallurgy hot isostatic pressing

Joining ferritic SA508 low alloy steel (LAS) and austenitic 316 L stainless steel (SS) via powder metallurgy hot isostatic pressing (PM-HIP) was evaluated as an alternative method to welding. This study investigated the mechanical and microstructural evolutions of the bimetallic interface under different joint designs and heat treatments. Here, the direct joining of dissimilar metal alloys by PM-HIP method resulted in two designs: 1) powder SA508 to solid bar 316 L (P508–B316L) and 2) powder 316 L solid bar SA508 (P316L-B508). In both cases, P508–B316L and P316L-demonstrated satisfactory tensile strength, however, high hardness and severe depreciation in toughness were located on the bimetallic interface. The mechanisms responsible for the detrimental mechanical properties were verified. Large oxides were observed in P508–B316L due to the prior powder boundary (PPB) oxides present in SA508 powder. The intense sensitization occurred from the formation of M 23 C 6 carbides, consequently from the slow cooling after PM-HIP in P316L-B508. Post-HIP heat treatments were explored to reduce the distance of carbide formation; however, the heat treatment could not eliminate the carbides. The experimental results were compared to the diffusion couple simulation as a function of carbide formation with distance. The analysis also showed the high hardness at the bimetallic interface was primarily contributed by solid solution strengthening. In conclusion, the direct joining of P316L-B508 and P508–B316L via PM-HIP was deemed to be unfeasible, and a transitional material is necessary to impede the diffusion of carbon.

316L stainless Steel↗

DOE OSTI2024

Self-similar Reynolds-averaged mechanical–scalar turbulence models for reshocked Richtmyer–Meshkov instability-induced mixing in the small Atwood number limit

Analytical self-similar solutions to two-, three-, and four-equation Reynolds-averaged mechanical–scalar turbulence models describing incompressible turbulent Richtmyer–Meshkov instability-induced mixing in planar geometry derived in the small Atwood number limit are extended to construct models for reshocked Richtmyer–Meshkov mixing. In this study, the models are based on the turbulent kinetic energy K and its dissipation rate ε, together with the scalar variance S and its dissipation rate χ modeled either differentially or algebraically. The three- and four-equation models allow for a simultaneous description of mechanical and scalar mixing, i.e., mixing layer growth and molecular mixing. Mixing layer growth parameters and other physical observables were obtained explicitly as functions of the model coefficients and were used to calibrate the model coefficients. Here, the solutions for the singly shocked Richtmyer–Meshkov case for the mixing layer width and the turbulent fields are used to construct piecewise-continuous generalizations of these quantities for times after reshock. For generality, the post-reshock mixing layer width is not assumed to grow with the same power-law as the pre-reshock width, and an impulsive approximation applied to Rayleigh–Taylor instability growth is used to establish the expression for the post-reshock width. A four-equation model is then used to illustrate the spatiotemporal behavior of the mean and turbulent fields and late-time turbulent equation budgets across the mixing layer. The reference solutions derived here can provide systematic calibrations and better understanding of mechanical–scalar turbulence models and their predictions for reshocked Richtmyer–Meshkov instability-induced turbulent mixing in the very large Reynolds number limit.

42 ENGINEERING↗

DOE OSTI2026

Janus skyrmion: Interfacial quasiparticle with two-faced helicity

Janus particles are functional particles with at least two surfaces showing asymmetric properties. Here, we show at the interface between two magnetic regions with different antisymmetric exchange interactions, an alternative species of two-dimensional topological quasiparticles can emerge, in which different helicity structures can coexist. We name such an interfacial quasiparticle a “Janus skyrmion,” in analogy to the Janus particle. As the Janus skyrmion shows helicity asymmetry, its size could vary with both the in-plane and out-of-plane magnetic fields. A vertical spin current could drive the Janus skyrmion into one-dimensional motion along the interface without showing the skyrmion Hall effect, at a speed which depends on both the in-plane spin-polarization direction and current density. Thermal fluctuations could also lead to one-dimensional random walk of a Brownian Janus skyrmion. This work uncovers unique dynamics intrinsic to interfacial quasiparticles with exotic helicity, which may be realized in interface-engineered magnetic layers.

36 MATERIALS SCIENCE↗

DOE OSTI2019

Fuel Matrix Degradation Model Development Update: Alloy Corrosion Rates and Hydrogen Generation

This work is being performed as part of the DOE NE Spent Fuel and Waste Science and Technology Campaign, Argillite and Crystalline Rock R&D work packages: SF-19AN01030101 and SF-19AN01030201. This document meets the milestone M4SF-19AN010301013 for Argillite R&D and the milestone M4SF-19AN010302013 for Crystalline R&D. The fuel matrix degradation (FMD) model calculates the degradation rate of spent UO2 fuel based on fundamental electrochemical theory and thermodynamics. The model provides the quantitative basis for radionuclide source term predictions in the generic disposal system analysis (GDSA) performance assessment (PA) model. The FMD model has been implemented in a manner that facilitates its integration with the GDSA-PA code and a preliminary, integrated FMD-GDSA model has been successfully tested (Jerden et al., 2017). The specific focus of on-going work is to accurately and quantitatively represent the generation of H2 in a breached waste package and its effect on the spent fuel degradation rate so that this key process can be accurately represented in PA models. It has been shown experimentally that millimolar concentrations of dissolved H2 in contact with spent fuel will inhibit oxidative dissolution and decrease the fuel degradation rates by as much as three orders of magnitude (e.g., Röllin et al., 2001, Ollila, 2008). This will lead to a significant decrease in the radionuclide source term values used in repository PA models. Sensitivity studies using the FMD model have shown that the dissolved H2 concentration is the dominant environmental variable affecting the UO2 spent fuel dissolution rate as long as a source of H2 persists in the breached waste package (Jerden et al., 2015). Therefore, on-going experimental and modeling efforts focus on H2 production, accumulation and interfacial reactions within a breached waste package. The anoxic corrosion of metallic engineering materials within a breached waste package will be the main source of H2 in crystalline and argillite rock repository systems. The most important H2-producing alloys present within a waste package include stainless steel, carbon steel, and aluminum alloys and the Zircaloy fuel cladding. A steel corrosion module was added to the FMD model to account for these H2 sources and couple the H2 generation rate with fuel degradation processes (Jerden et al., 2017). As discussed below, there is a need for experimental data from electrochemical corrosion tests to quantify the H2 generation rates due to the corrosion of these waste package alloys as a function of key environmental variables (Eh, pH, groundwater chemistry). This report presents results from series of electrochemical corrosion tests with materials present in waste packages that provide information needed to parameterize and validate the FMD model. The alloys tested include 316L stainless steel (316SS), AISI 4320 carbon steel (C-steel) and Zircaloy-4 fuel cladding (unirradiated). Potentiodynamic polarization and potentiostatic polarization tests were performed in buffer solutions at pH 4, 7 and 10 with NaCl concentrations of 0, 4 and 100 millimolar (mM). The potentiostatic tests were performed at voltages varying from 0.5 volts down to -0.66 volts, vs the standard hydrogen electrode (SHE), and all tests were performed at laboratory ambient temperatures (~22 °C). The corrosion rates measured during the electrochemical tests were used as direct input to a new FMD/in-package chemistry model that is being developed to provide accurate long-term spent fuel degradation rates as chemical conditions (Eh, pH, speciation) evolve within a breached waste package. This new model was developed by coupling the FMD model with the reactive transport code X1t, which is a module within the Geochemist’s Workbench (GWB) reaction path modeling code (Jerden et al., 2019). The reactive transport model consists of a 1D domain discretized with 21 reaction diffusion cells and includes a single waste packag

Jerden, James↗

DOE OSTI2023

Workshop on Addressing Rigor and Reproducibility in Thermal, Heterogeneous Catalysis

Heterogeneous catalysis has long served as the bedrock of the manufacturing of energy carriers, fuels and chemicals, and various technologies for pollution abatement. The significant complexity and variability spanning the entire breadth of catalyst material properties, synthesis methods, characterization techniques, and evaluation procedures, has focused attention on the need to establish community-accepted best practices for ensuring high-quality, benchmarked, and reproducible data. In addition, increased societal urgency to transition to clean energy and reduce greenhouse gas concentrations has incentivized interdisciplinary, convergent, and translational approaches to catalysis research in recent years. Research engineers and scientists with expertise cutting broadly across materials science, chemical synthesis, interfacial science, spectroscopy, and methods of data science and computational simulation, all bring diverse and important perspectives to catalysis research, but often with little awareness of the complexity of catalytic systems, especially in their working environment. As has already occurred in other scientific fields, there has been growing recognition and consensus in the heterogeneous catalysis research community that mechanisms are needed to improve the rigor and reproducibility (R&R) of experimental measurements, to ensure alignment of the broader research community with a common core of best practices specific to the realization of high-quality catalysis research. Similarly, the field is moving rapidly toward computationally informed and data science-driven catalyst design, but the success of implementing such predictive tools hinges on model training and validation rooted in rigorously obtained and reproducible experimental data that are benchmarked to common specifications. As such, this workshop was convened to prepare a report summarizing best practices for reporting data and performing experiments that researchers can use to benchmark, validate, and reproduce data in specific sub-fields of thermal, heterogeneous catalysis. Additionally, we discussed recommendations for future actions that may improve R&R in this field. The workshop organizers and participants include a diverse range of catalysis researchers from various employment sectors (e.g., academia, industry, national laboratory), institutional mission and resources (e.g., PhD-granting research universities, non-PhD-granting teaching universities), career stage (e.g., early, mid and late-career), technical expertise, and demographic background. This diverse group was involved in the discussion of workshop agenda items, writing this report, and discussing possible future action items for the community to consider, which helped ensure that a broad range of perspectives were captured in the description of the problems at hand and the creation of actionable solutions that may be effectively adopted by the diverse practitioners in catalysis research. Importantly, this group of workshop participants also included very early career researchers (e.g., senior PhD students, postdoctoral scholars) who will become the next generation of scientific leaders in various sectors, thus capturing emerging perspectives of newcomers to the field to shape its future while positively impacting the development of its future workforce. We envision that this effort will help advance the field of catalysis science by improving the rigor and reproducibility of experimental data collected by current researchers and future newcomers to the field, which is of broad importance to health and vitality of any scientific discipline. Therefore, best practices identified in this endeavor for thermal heterogeneous catalysis can be translated to such efforts in other areas of catalysis and other scientific fields involving the study of materials, and vice versa. We also envision this to be an ongoing effort, with future workshops that are convened to discuss issues of rigor and reproducibility on technical topics that were unable to be covered in this workshop due to its scope limitations, and as emerging methods and materials become more prevalent in the research community.

36 MATERIALS SCIENCE↗

DOE OSTI2024

N and OH-Immobilized Cu 3 Clusters In Situ Reconstructed from Single-Metal Sites for Efficient CO 2 Electromethanation in Bicontinuous Mesochannels

Cu-based catalysts hold promise for electrifying CO 2 to produce methane, an extensively used fuel. However, the activity and selectivity remain insufficient due to the lack of catalyst design principles to steer complex CO 2 reduction pathways. Herein, we develop a concept to design carbon-supported Cu catalysts by regulating Cu active sites’ atomic-scale structures and engineering the carbon support’s mesoscale architecture. This aims to provide a favorable local reaction microenvironment for a selective CO 2 reduction pathway to methane. In situ X-ray absorption and Raman spectroscopy analyses reveal the dynamic reconstruction of nitrogen and hydroxyl-immobilized Cu 3 (N,OH-Cu 3 ) clusters derived from atomically dispersed Cu–N 3 sites under realistic CO 2 reduction conditions. The N,OH-Cu 3 sites possess moderate *CO adsorption affinity and a low barrier for *CO hydrogenation, enabling intrinsically selective CO 2 -to-CH 4 reduction compared to the C–C coupling with a high energy barrier. Importantly, a block copolymer-derived carbon fiber support with interconnected mesopores is constructed. The unique long-range mesochannels offer an H 2 O-deficient microenvironment and prolong the transport path for the CO intermediate, which could suppress the hydrogen evolution reaction and favor deep CO 2 reduction toward methane formation. Thus, the newly developed catalyst consisting of in situ constructed N,OH-Cu 3 active sites embedded into bicontinuous carbon mesochannels achieved an unprecedented Faradaic efficiency of 74.2% for the CO 2 reduction to methane at an industry-level current density of 300 mA cm –2 . In conclusion, this work explores effective concepts for steering desirable reaction pathways in complex interfacial catalytic systems via modulating active site structures at the atomic level and engineering pore architectures of supports on the mesoscale to create favorable microenvironments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1998

Cyclic Fiber Push-In Test Monitors Evolution of Interfacial Behavior in Ceramic Matrix Composites

SiC fiber-reinforced ceramic matrix composites are being developed for high-temperature advanced jet engine applications. Obtaining a strong, tough composite material depends critically on optimizing the mechanical coupling between the reinforcing fibers and the surrounding matrix material. This has usually been accomplished by applying a thin C or BN coating onto the surface of the reinforcing fibers. The performance of these fiber coatings, however, may degrade under cyclic loading conditions or exposure to different environments. Degradation of the coating-controlled interfacial behavior will strongly affect the useful service lifetime of the composite material. Cyclic fiber push-in testing was applied to monitor the evolution of fiber sliding behavior in both C- and BN-coated small-diameter (15-mm) SiC-fiber-reinforced ceramic matrix composites. The cyclic fiber push-in tests were performed using a desktop fiber push-out apparatus. At the beginning of each test, the fiber to be tested was aligned underneath a 10- mm-diameter diamond punch; then, the applied load was cycled between selected maximum and minimum loads. From the measured response, the fiber sliding distance and frictional sliding stresses were determined for each cycle. Tests were performed in both room air and nitrogen. Cyclic fiber push-in tests of C-coated, SiC-fiber-reinforced SiC showed progressive increases in fiber sliding distances along with decreases in frictional sliding stresses for continued cycling in room air. This rapid degradation in interfacial response was not observed for cycling in nitrogen, indicating that moisture exposure had a large effect in immediately lowering the frictional sliding stresses of C-coated fibers. These results indicate that matrix cracks bridged by C-coated fibers will not be stable, but will rapidly grow in moisture-containing environments. In contrast, cyclic fiber push-in tests of both BN-coated, SiC-fiber-reinforced SiC and BNcoated, SiC-fiber-reinforced barium strontium aluminosilicate showed no significant changes in fiber sliding behavior with continued short-term cycling in either room air or nitrogen. Although the composites with BN-coated fibers showed stable short-term cycling behavior in both environments, long-term (several-week) exposure of debonded fibers to room air resulted in dramatically increased fiber sliding distances and decreased frictional sliding stresses. These results indicate that although matrix cracks bridged by BNcoated fibers will show short-term stability, such cracks will show substantial growth with long-term exposure to moisture-containing environments. Newly formulated BN coatings, with higher moisture resistance, will be tested in the near future.

Eldridge, Jeffrey I.↗

NASA NTRS1991

Development of graphite/copper composites utilizing engineered interfaces

In situ measurements of graphite/copper alloy contact angles were made using the sessile drop method. The interfacial energy values obtained from these measurements were then applied to a model for the fiber matrix interfacial debonding phenomenon found in graphite/copper composites. The formation obtained from the sessile drop tests led to the development of a copper alloy that suitably wets graphite. Characterization of graphite/copper alloy interfaces subjected to elevated temperatures was conducted using Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Auger Electron Spectroscopy, and X Ray Diffraction analyses. These analyses indicated that during sessile drop tests conducted at 1130 C for 1 hour, copper alloys containing greater than 0.98 at pct chromium form continuous reaction layers of approx. 10 microns in thickness. The reaction layers are adherent to the graphite surface. The copper wets the reaction layer to form a contact angle of 60 deg or less. X ray diffraction results indicate that the reaction layer is Cr3C2.

Devincent, Sandra M.↗

DOE OSTI2018

Surface Engineering of Nanostructured Energy Materials

All nanostructures share a common feature of large surface-to-volume ratio, which makes surface engineering a vital tool for exploring their new and important applications in many different areas. Particularly, inorganic nanostructures represent a class of intriguing catalysts that can find wide uses in energy conversion, energy storage, and environmental remediation. In this work, a number of surface engineering strategies, including morphology control, defect incorporation, and interface manipulation for tailoring the shape, facet, defect, interfacial property, and composition of nanostructures, aiming at controlling the chemical and physical properties such as energy bandgap and surface energy toward great enhancement in catalytic performance, are discussed.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Relation between interfacial shear and friction force in 2D materials

Understanding the interfacial properties between an atomic layer and its substrate is of key interest at both the fundamental and technological levels. From Fermi level pinning to strain engineering and superlubricity, the interaction between a single atomic layer and its substrate governs electronic, mechanical and chemical properties. Here, we measure the hardly accessible interfacial transverse shear modulus of an atomic layer on a substrate. By performing measurements on bulk graphite, and on epitaxial graphene films on SiC with different stacking orders and twisting, as well as in the presence of intercalated hydrogen, we find that the interfacial transverse shear modulus is critically controlled by the stacking order and the atomic layer–substrate interaction. Importantly, we demonstrate that this modulus is a pivotal measurable property to control and predict sliding friction in supported two-dimensional materials. The experiments demonstrate a reciprocal relationship between friction force per unit contact area and interfacial shear modulus. As a result, the same relationship emerges from simulations with simple friction models, where the atomic layer– substrate interaction controls the shear stiffness and therefore the resulting friction dissipation.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Electrolyte Design for Fast‐Charging Lithium‐Based Batteries

Fast charging is essential for the widespread adoption of lithium (Li)-ion batteries, but it is fundamentally limited by sluggish interfacial kinetics, Li plating, and electrolyte instability at high current densities. Over the past decade, electrolyte engineering has emerged as a key strategy to address these challenges. This review summarizes the development of fast-charging electrolytes over the past ten years and outlines a design framework. Electrolyte formulations are first deconstructed into their main components—solvents, salts, and functional additives—and representative strategies for tuning solvation structure and interphase chemistry are discussed to suppress Li plating and improve interfacial kinetics. The discussion then extends to advanced electrolyte systems, particularly localized high-concentration electrolytes (LHCEs), and their compatibility with different anode chemistries. Advanced characterization techniques are also summarized and categorized based on destructiveness, spatial and temporal resolution, quantitative analysis, and the chemical species or processes probed across multiple length scales. Recent progress in AI-enabled electrolyte discovery and battery management system (BMS) strategies for optimized fast-charging protocols is further highlighted. Finally, perspectives are presented on translating electrolyte innovations from academic research to practical applications, with emphasis on cell format, realistic operating conditions, and manufacturability.

25 ENERGY STORAGE↗

DOE OSTI2023

Long‐Range Confinement‐Driven Enrichment of Surface Oxygen‐Relevant Species Promotes C−C Electrocoupling in CO 2 Reduction

Abstract CO 2 reduction is a highly attractive route to transform CO 2 into useful feedstocks, of which C 2 products are more desired than C 1 , yet face high kinetic barriers of C−C electrocoupling. Here, the engineering of pore‐enabled local confinement reaction environments is reported for tuning the enrichment of surface‐adsorbed oxygen‐relevant species and the establishment of their pronounced benefits in promoting C−C coupling over oxide‐derived Cu‐based catalysts. A new approach of utilizing the microphase separation of a block copolymer is developed to fabricate bicontinuous mesoporous CuO nanofibers (CuO‐BPNF). The enhanced confinement from long‐range mesochannels enables the adsorption of OH ad /O ad on the Cu surface at a wide negative potential range of −0.7 – −1.3 V in CO 2 reduction, which cannot be achieved over conventional deficient and short‐range pores. Constant‐potential DFT calculations reveal that the surface‐bound oxygen species weakens *CO affinity with the Cu (111) surface and lowers the kinetic barriers for both *CO−CO dimerization and *CO hydrogenation to enable *CO−CHO coupling. Accordingly, a CO 2 ‐to‐C 2 Faradaic efficiency of 74.7% over CuO‐BPNF is shown, significantly larger than counterparts with conventional pores. This work offers a general design principle of confinement engineering to manage the adsorption of reactive species for steering reaction pathways in interfacial catalysis.

Chemistry↗

DOE OSTI2022

Emergence of electric-field-tunable interfacial ferromagnetism in 2D antiferromagnet heterostructures

Van der Waals (vdW) magnet heterostructures have emerged as new platforms to explore exotic magnetic orders and quantum phenomena. Here, we study heterostructures of layered antiferromagnets, CrI 3 and CrCl 3 , with perpendicular and in-plane magnetic anisotropy, respectively. Using magneto-optical Kerr effect microscopy, we demonstrate out-of-plane magnetic order in the CrCl 3 layer proximal to CrI 3 , with ferromagnetic interfacial coupling between the two. Such an interlayer exchange field leads to higher critical temperature than that of either CrI 3 or CrCl 3 alone. We further demonstrate significant electric-field control of the coercivity, attributed to the naturally broken structural inversion symmetry of the heterostructure allowing unprecedented direct coupling between electric field and interfacial magnetism. These findings illustrate the opportunity to explore exotic magnetic phases and engineer spintronic devices in vdW heterostructures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2024

Methods of fabricating porous ceramic electrodes for solid state battery applications

Compositions and methods for the fabrication of electrode and porous lithium-garnet electrolyte scaffolds for use in solid state batteries and other devices are provided. The methods produce porous structures using phase inversion or high shear compaction processes to fabricate a solid-state battery electrode material from LLZO electrolytes. Engineered electrode structures with a porous scaffold of solid electrolyte material provide lower interfacial resistances and a mechanical support for a thin solid electrode layer improving performance.

Tucker, Michael↗

DOE OSTI2021

Comparison of water nanodroplet properties on different graphite-based substrates

The molecular structure and dynamics of water differ considerably at various interfaces. We compare the interfacial water structure–property relationship on three different carbon substrates, namely, amorphous carbon, compressed expanded natural graphite, and pure graphite by utilizing atomistic molecular dynamics simulations. The effect of different substrates on the structural and dynamical properties of water can readily be observed. Here, the density distributions parallel and normal to the substrates show oblate droplet structures. The normal to the substrate water distribution shows a strong hydration layer at the interface that does not vary with substrates. However, the disparity in the structure and dynamics on three different substrates shows that the surface morphologies of the substrates are critical for determining nanoscale water properties. Furthermore, it is observed that the formation of an interfacial water layer or the hydration layer is a direct consequence of both water “confinement” at the nanoscale and “attraction” between water molecules and the carbon substrates.

42 ENGINEERING↗

DOE OSTI2019

Interfacial Octahedral Manipulation Imparts Hysteresis-Free Metal to Insulator Transition in Ultrathin Nickelate Heterostructure

Much like epitaxial strain, engineering oxygen octahedral rotations (OORs) in perovskite oxide thin films can be a powerful means of manipulating their physical and chemical properties. Here, it is demonstrated that the fundamental character of the metal-insulator transition (MIT) can be sensitively controlled by the structure of the oxygen sublattice for NdNiO 3 thin films grown epitaxially on NdGaO 3 (110) substrates. The MIT is sharp and hysteretic for a Ni-O-Ni bond angle of 154.0° (6 nm thick film) like the bulk behavior, while it is diffuse and largely nonhysteretic for a bond angle of 149.5° (3 nm thick film), stemming from the smaller bond angle of the NdGaO 3 substrate. Using synchrotron X-ray diffraction to quantify the geometric framework of the oxygen sublattice, it is found that the influence of the substrate OORs propagates and decays after a few nanometers into the ultrathin film. The sublattice structure in the 6 nm thick film is similar to that for bulk NdNiO 3 , leading to the sharp and hysteretic MIT.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Engineering ligand reactivity enables high-temperature operation of stable perovskite solar cells

Perovskite solar cells (PSCs) consisting of interfacial two- and three-dimensional heterostructures that incorporate ammonium ligand intercalation have enabled rapid progress toward the goal of uniting performance with stability. However, as the field continues to seek ever-higher durability, additional tools that avoid progressive ligand intercalation are needed to minimize degradation at high temperatures. We used ammonium ligands that are nonreactive with the bulk of perovskites and investigated a library that varies ligand molecular structure systematically. Here, we found that fluorinated aniliniums offer interfacial passivation and simultaneously minimize reactivity with perovskites. Using this approach, we report a certified quasi–steady-state power-conversion efficiency of 24.09% for inverted-structure PSCs. In an encapsulated device operating at 85°C and 50% relative humidity, we document a 1560-hour T85 at maximum power point under 1-sun illumination.

14 SOLAR ENERGY↗

DOE OSTI2019

Carbon nanotube-based mixed-matrix membranes with supramolecularly engineered interface for enhanced gas separation performance

Here in this study, novel nanocomposite membranes were fabricated from single-walled carbon nanotubes (SWNTs) and a triptycene-containing polyimide. The desirable interfacial morphology and homogenous dispersion of SWNTs were achieved by strong π-π stacking and supramolecular shape-fitting interactions between the nanotube and the paddlewheel-shaped triptycene moieties in polymer matrix. Mixed-matrix membranes (MMMs) containing 2–15 wt% of as-purchased SWNTs (AP-SWNTs) were prepared and tested for their gas transport properties. While all MMMs showed greatly enhanced permeabilities with well-maintained selectivities, a non-linear dependence of permeability on filler content was observed. Another series of MMMs with purified SWNTs (P-SWNTs) and acid-treated SWNT (A-SWNTs) were also prepared. The functionalized A-SWNT MMM exhibited the best separation performance at 2 wt% filler content among all MMMs, which can be attributed to the improved interfacial affinity with carboxylic acid functionalized surface of A-SWNTs.

42 ENGINEERING↗