Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “inp”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Photovoltaic characteristics of n(+)pp(+) InP solar cells grown by OMVPE

The photovoltaic characteristics of n(+)/p/p(+) homojunction InP solar cells fabricated by organometallic vapor-phase epitaxy (OMVPE) are described. The cells are characterized by I-V, C-V and quantum efficiency measurements, and simulations are used to obtain various device and material parameters. The I-V characteristics show a high recombination rate in the depletion region; this is shown to be independent of the impurity used. It is shown that cadmium is easier to use as an acceptor for the p base and p(+) buffer and is therefore beneficial. The high quantum efficiency of 98 percent at long wavelengths measured in these cells indicates a very good collection efficiency in the base. The short-wavelength quantum efficiency is poor, indicating a high surface recombination.

Tyagi, S.↗
NASA NTRS1990

Recent results from the InP homojunction cell module on the LIPS III spacecraft

The flight performance of the NASA Lewis Research Center's indium phosphide homojunction cell module on the LIPs III spacecraft is presented. Four n+-p diffused junction cells, an early product of an InP development program, were flown. The voltage range of the data prohibits determination of the open-circuit voltage or the maximum power point. However, analysis of the 32 months of short-circuit current data reveals a slight increase, not the 4 percent decrease expected from radiation tolerance studies. This increase may be due to continual cleaning of possible prelaunch dust contamination or changes in data acquisition system calibration. For all cells, the average short-circuit current remains below prelaunch values.

Brinker, David J.↗
NASA NTRS1992

Defect behavior, carrier removal and predicted in-space injection annealing of InP solar cells

Defect behavior, observed by deep level transient spectroscopy (DLTS), is used to predict carrier removal and the effects of simultaneous electron irradiation and injection annealing of the performance of InP solar cells. For carrier removal, the number of holes trapped per defect is obtained from measurements of both carrier concentrations and defect concentrations during an isochronal anneal. In addition, from kinetic considerations, the behavior of the dominant defect during injection annealing is used to estimate the degradation expected from exposure to the ambient electron environment in geostationary orbit.

Weinberg, I.↗
NASA NTRS1992

Texturing of InP surfaces for device applications

A unique process for texturing InP (100) wafers by anisotropic etching was developed. The process produces irregular V-grooves on the surface, which reduce the surface reflectivity. The process does not require photolithography or masking. The etching characteristics depend on doping, with etching tending to proceed more rapidly on the more heavily doped samples. Reduced reflectivity surfaces formed using this process can be applied to solar cells, photodetectors, and other optoelectronic devices.

Bailey, Sheila G.↗
NASA NTRS1991

Modeling of InP metalorganic chemical vapor deposition

The growth of InP by metalorganic chemical vapor deposition (MOCVD) in a horizontal reactor is being modeled with a commercially available computational fluid dynamics modeling code. The mathematical treatment of the MOCVD process has four primary areas of concern: 1) transport phenomena, 2) chemistry, 3) boundary conditions, and 4) numerical solution methods. The transport processes involved in CVD are described by conservation of total mass, momentum, energy, and atomic species. Momentum conservation is described by a generalized form of the Navier-Stokes equation for a Newtonian fluid and laminar flow. The effect of Soret diffusion on the transport of particular chemical species and on the predicted deposition rate is examined. Both gas-phase and surface chemical reactions are employed in the model. Boundary conditions are specified at the inlet and walls of the reactor for temperature, fluid flow and chemical species. The coupled set of equations described above is solved by a finite difference method over a nonuniform rectilinear grid in both two and three dimensions. The results of the 2-D computational model is presented for gravity levels of zero- and one-g. The predicted growth rates at one-g are compared to measured growth rates on fused silica substrates.

Black, Linda R.↗
NASA NTRS1993

Simple, extremely low resistance contact system to n-InP that does not exhibit metal-semiconductor intermixing during sintering

Contact formation to InP is plagued by the violent metal-semiconductor intermixing that takes place during the contact sintering process. We have discovered a truly unique contact system, involving Au and Ge, which is easily fabricated, which exhibits extremely low values of contact resistivity, and in which there is virtually no metal-semiconductor interdiffusion, even after extended sintering. We present a description of this contact system and suggest possible mechanisms to explain the observed behavior.

Weizer, Victor G.↗
NASA NTRS1993

Ellipsometric characterization of In(0.52)Al(0.48)As and of modulation doped field effect transistor structures on InP substrates

The dielectric function of a thick layer of In(0.52)Al(0.48)As lattice matched to InP was measured by variable angle spectroscopic ellipsometry in the range 1.9-4.1 eV. The In(0.52)Al(0.48)As was protected from oxidation using a thin In(0.53)Ga(0.47)As cap that was mathematically removed for the dielectric function estimate. The In(0.52)Al(0.48)As dielectric function was then verified by ellipsometric measurements of other In(0.53)Ga(0.47)As/In(0.52)Al(0.48)As structures, including (MODFET), and is shown to provide accurate structure layer thicknesses.

Alterovitz, S. A.↗
NASA NTRS1993

Minority carrier diffusion length and edge surface-recombination velocity in InP

A scanning electron microscope was used to obtain the electron-beam-induced current (EBIC) profiles in InP specimens containing a Schottky barrier perpendicular to the scanned (edge) surface. An independent technique was used to measure the edge surface-recombination velocity. These values were used in a fit of the experimental EBIC data with a theoretical expression for normalized EBIC (Donolato, 1982) to obtain the electron (minority carrier) diffusion length.

Hakimzadeh, Roshanak↗
NASA NTRS1993

A detailed study of the photo-injection annealing of thermally diffused InP solar cells

A detailed analysis of the annealing of thermally diffused InP solar cells fabricated by the Nippon Mining Co. is presented. The cells were irradiated with 1 MeV electrons, and the induced degradation is measured using deep level transient spectroscopy and low temperature (86 K) IV measurements. Clear recovery of the photovoltaic parameters is observed during low temperature (T is less than 300 K) solar illuminations (1 sun, AMO) with further recovery at higher temperatures (300 less than T less than 500 K). For example, the output of a cell which was irradiated up to a fluence of 1 x 10(exp 16) cm(sup -2) was observed to recover to within 5 percent of the pre-irradiation output. An apparent correlation between the recovery of I(sub sc) and the annealing of the H4 defect and of the minority carrier trapping centers is observed. An apparent correlation between the recovery of VO, and the annealing of the H5 defect is also observed. These apparent correlations are used to develop a possible model for the mechanism of the recovery of the solar cells.

Walters, R. J.↗
NASA NTRS1993

High temperature annealing of minority carrier traps in irradiated MOCVD n(+)p InP solar cell junctions

Deep level transient spectroscopy was used to monitor thermal annealing of trapping centers in electron irradiated n(+)p InP junctions grown by metalorganic chemical vapor deposition, at temperatures ranging from 500 up to 650K. Special emphasis is given to the behavior of the minority carrier (electron) traps EA (0.24 eV), EC (0.12 eV), and ED (0.31 eV) which have received considerably less attention than the majority carrier (hole) traps H3, H4, and H5, although this work does extend the annealing behavior of the hole traps to higher temperatures than previously reported. It is found that H5 begins to anneal above 500K and is completely removed by 630K. The electron traps begin to anneal above 540K and are reduced to about half intensity by 630K. Although they each have slightly different annealing temperatures, EA, EC, and ED are all removed by 650K. A new hole trap called H3'(0.33 eV) grows as the other traps anneal and is the only trap remaining at 650K. This annealing behavior is much different than that reported for diffused junctions.

Messenger, S. R.↗
NASA NTRS1993

Activation energy and capture cross section of majority carrier traps in Zn doped InP

Schottky barrier diodes were fabricated on Zn doped InP Wafers. The diodes were radiation damaged with 2 MeV protons to a dose of 2 x 10(exp 12)cm(sup -2). The damage was analyzed by DLTS (deep level transient spectroscopy) using the double correlation technique. Capture cross sections were measured directly. Two major defects were observed in the DLTS spectra. The first defect, was H4 at Ev + 0.29 eV, with capture cross section 1.1 x 10(exp -17)cm(sup 2). The second defect, was H5 at Ev + 0.53 eV. Its capture cross section varied with temperature as described by the relationship sigma = sigma(sub 0) exp(delta(E)/kT) where sigma(sub 0) = 1.3 x 10(exp -19)cm(sup 2) and delta(E) = .08 eV. This relationship yields a sigma of 5.9 x 10(exp -21)cm(sup 2) at room temperature. The surprisingly small capture cross section of H5 and its temperature dependence are discussed in terms of the multiphonon emission process for carrier capture at the defect. The advantages of the improved experimental techniques used are also discussed.

Rybicki, George↗
NASA NTRS1993

Measurement of the minority carrier diffusion length and edge surface-recombination velocity in InP

A scanning electron microscope (SEM) was used to measure the electron (minority carrier) diffusion length (L(sub n)) and the edge surface-recombination velocity (V(sub s)) in zinc-doped Czochralski-grown InP wafers. Electron-beam-induced current (EBIC) profiles were obtained in specimens containing a Schottky barrier perpendicular to the scanned (edge) surface. An independent technique was used to measure V(sub s), and these values were used in a theoretical expression for normalized EBIC. A fit of the experimental data with this expression enabled us to determine L(sub n).

Bailey, Sheila G.↗
NASA NTRS1993

Heteroepitaxial InP, and ultrathin, directly glassed, GaAs 3-5 solar cells

The commercial application of Indium Phosphide solar cells in practical space missions is crucially dependent upon achieving a major cost reduction which could be offered by heteroepitaxy on cheaper, more rugged substrates. Furthermore, significant mass reduction, compatibility with mechanically stacked multijunction cells, and elimination of the current loss through glue discoloration, is possible in III-V solar cells by the development of ultrathin, directly glassed cells. The progress of a UK collaborative program to develop high efficiency, homojunction InP solar cells, grown by MOCVD on Si substrates, is described. Results of homoepitaxial cells (is greater than 17 percent 1 Sun AM0) are presented, together with progress in achieving low dislocation density heteroepitaxy. Also, progress in a UK program to develop ultrathin directly-glassed GaAs cells is described. Ultrathin (5 micron) GaAs cells, with 1 Sun AM0 efficiencies up to 19.1 percent, are presented, together with progress in achieving a direct (adhesive-less) bond between the cell and coverglass. Consequential development to, for example, cell grids, are also discussed.

Hardingham, C. M.↗
NASA NTRS1994

InP solar cell with window layer

The invention features a thin light transmissive layer of the ternary semiconductor indium aluminum arsenide (InAlAs) as a front surface passivation or 'window' layer for p-on-n InP solar cells. The window layers of the invention effectively reduce front surface recombination of the object semiconductors thereby increasing the efficiency of the cells.

Jain, Raj K.↗
NASA NTRS1992

Progress in p(+)n InP solar cells fabricated by thermal diffusion

In SPRAT XI, we proposed that p(sup +)n diffused junction InP solar cells should exhibit a higher conversion efficiency than their n(sup +)p counterparts. This was mainly due to the fact that our p(sup +)n (Cd,S) cell structures consistently showed higher V (sub OC) values than our n(sup +)p (S,Cd) structures. The highest V(sub OC) obtained with the p(sup +)n (Cd,S) cell configuration was 860 mV, as compared to the highest V(sub OC) 840 mV obtained with the n(sup +)p (S,Cd) configuration (AMO, 25 C). In this work, we present the performance results of our most recent thermally diffused cells using the p(sup +)n (Cd,S) structure. We have been able to fabricate cells with V(sub OC) values approaching 880 mV. Our best cell with an unoptimized front contact grid design (GS greater than or equal to 10%) showed a conversion efficiency of 13.4% (AMO, 25 C) without an AR coating layer. The emitter surface was passivated by a -50A P rich oxide. Achievement of such high V(sub OC) values was primarily due to the fabrication of emitter surfaces, having EPD densities as low as 2E2 cm(sup -2) and N(sub a)N(sub d) of about 3E18 cm (sup -3). In addition, our preliminary investigation of p(sup +)n structures seem to suggest that Cd-doped emitter cells are more radiation resistant than Zn-doped emitter cells against both high energy electron and proton irradiation.

Faur, Mircea↗
NASA NTRS1996

InP tunnel junctions for InP/InGaAs tandem solar cells

We report, for the first time, an epitaxially grown InP p(+)/n(++) tunnel junction. A diode with peak current densities up to 1600 A/cm and maximum specific resistivities (Vp/Ip - peak voltage to peak current ratio) in the range of 10(exp -4)Omega cm(exp 2) is obtained. This peak current density is comparable to the highest results previously reported for lattice matched In(0.53)Ga(0.47)As tunnel junctions. Both results were obtained using chemical beam epitaxy (CBE). In this paper we discuss the electrical characteristics of these tunnel diodes and how the growth conditions influence them.

Vilela, Mauro F.↗
NASA NTRS1997

Fabrication and Characterization of a Long Wavelength InP HBT-Based Optical Receiver

Development of a high speed photodetector - the InP-based phototransistor (HPT) for use in optical receivers for microwave signal distribution for satellite phased array antennas is addressed. Currently, p-i-n photodetectors are used because of their compatibility with the heterojunction bipolar transistor (HBT), but their performance limits the bandwidth of these optical receivers. The HPT photodetector was investigated here as an alternative photodetector for monolithic integration with heterojunction bipolar transistor amplifiers in long wavelength (1.3 micron), gigahertz (GHz) frequency optical receivers.

Roenker, Kenneth P.↗
NASA NTRS1995

InP Tunnel Junctions for InP/InGaAs Tandem Solar Cells

We report, for the first time, an epitaxially grown InP p(+)/n(++) tunnel junction. A diode with peak current densities up to 1600 Al/sq cm and maximum specific resistivities (Vp/lp - peak voltage to peak current ratio) in the range of 10(exp -4)Om sq cm is obtained. This peak current density is comparable to the highest results previously reported for lattice matched In(0.53)Ga(0.47)As tunnel junctions. Both results were obtained using chemical beam epitaxy (CBE). In this paper we discuss the electrical characteristics of these tunnel diodes and how the growth conditions influence them.

Vilela, M. F.↗