Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “hydrothermal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Rheology and engine performance of very low sulfur fuel oil blended with 10% fast pyrolysis and hydrothermal liquefaction oils in a 2-stroke crosshead engine

The performance and emissions for a downscaled single-cylinder 2-stroke crosshead engine were determined for a very low sulfur fuel oil (VLSFO) when blended with 10 wt.% fast pyrolysis (FP) or hydrothermal liquefaction (HTL) bio-intermediates. The FP and HTL oils were derived from biomass and were observed to contain lower molecular weight (MW) hydrocarbons than neat VLSFO (which was evaluated as a baseline comparison). The addition of either biofuel reduced the overall viscosity of the VLSFO. Aging tests at 50, 90, and 120°C showed that the dynamic viscosity of VLSFO increased with exposure time up to two weeks. Similar trends were observed for the FP and HTL blends, but a pronounced spike in viscosity occurred for these fuels during the early period of exposure. None of the viscosity increases exceeded the operational limits of fuel system pumps. Engine performance studies were conducted under low, medium and high load operational settings. The relative performance of the test fuels was highly dependent on operating condition. In general, the engine results for the three test fuels were similar, but modest improvements in brake thermal efficiency and brake specific fuel consumption were observed, which may be attributed to the heightened reactivity of low molecular weight fraction of the FP and HTL oils.

09 BIOMASS FUELS↗
DOE OSTI2021

Changing chemistry of particulate manganese in the near- and far-field hydrothermal plumes from 15°S East Pacific Rise and its influence on metal scavenging

Dissolved Mn(II) in the hydrothermal plume is known to be microbially oxidized to form Mn(III/IV) oxides, and the Mn oxides scavenge other trace elements in seawater. In the GEOTRACES GP16 cruise, dissolved Mn (dMn) and particulate Mn (pMn) were found to be transported over 4000 km westwards from the Southern Eastern Pacific Rise. Previous studies in this plume showed different removal rates of dMn and pMn as well as pMn size distribution between the near-field (<80 km from the ridge axis) and far-field (>80 km) plumes. In order to understand Mn cycling in these plumes, spatial distribution, oxidation states, and mineral structures of Mn in small size fraction (SSF; 0.8–51 μm) and large size fraction (LSF; >51 μm) particles from the near-field and far-field plumes were examined using micro X-ray fluorescence spectrometry (μ-XRF), X-ray absorption near-edge structure spectroscopy (XANES), chemical species mapping, and extended X-ray absorption fine-structure spectroscopy (EXAFS). In the near-field plume, pMn in the SSF is dominated by oxidized Mn with Mn(III) fractions of ~30%. They are a mixture of δ-MnO 2 and triclinic birnessites that is known to be formed as a result of autocatalytic Mn(II) oxidation at the surface of freshly-formed δ-MnO2, suggesting that both microbial and autocatalytic Mn oxidation occur in the near-field plume. The LSF pMn in the near-field plume is also oxidized and often found in large aggregates several hundreds of μm in size. These aggregates settle out in the near-field and during transport, and are not found in the far-field plume. In the far-field plume where Mn oxides are not newly formed, pMn in the SSF is oxidized, but their Mn(III) fractions are smaller than in the near-field pMn. Unlike the SSF, the far-field plume LSF pMn is dominated by reduced Mn, implying very slow aggregation of pMn in the far-field plume. The different characteristics of pMn between the near-field and far-field plumes affect its scavenging of other trace elements. In the near-field plume, Co, Mo, 231 Pa are associated with pMn, but not in the far-field plume. 231 Pa is adsorbed to pFe rather than pMn in the far-field plume, and Pb is adsorbed to pFe in the entire plume. The result shows that freshly-formed Mn oxides in the near-field plume have higher scavenging capacity than the far-field plume pMn. Our findings suggest that the mineralogical age of Mn oxides may be an important parameter that controls the scavenging of many other trace elements and isotopes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A combined experimental and modelling study of granite hydrothermal alteration

Geochemical reactions can induce significant changes of rock reservoir porosity and permeability via mineral dissolution and precipitation processes, affecting the long-term fluid behaviour within various geological systems. Here, the understanding and quantification of these reactions rely on field and experimental studies and on the predictions of reactive transport models. The present study was aimed at assessing the extent to which current geochemical models integrating available mineral dissolution/precipitation rate equations can reproduce the experimental data obtained from 4 to 17-day long hydrothermal alteration experiments of a muscovite-biotite granite and, thus, help provide an accurate description of the evolution of geothermal systems within granitic reservoirs. The experiments were conducted at a constant temperature of 180 °C and over an aqueous fluid pH range of 2 to 8.5, using both mixed-flow and static batch reactors. Modelled major element (K, Al, Si, Ca, and Mg) concentrations were generally in satisfactory agreement with the corresponding measured elemental fluxes – the differences between modelled and experimental values were generally within a factor of 5 – and the predicted identity and mass of formed secondary phases were consistent with the microscopic observations of the reacted solids. However, larger differences between measured and modelled element concentrations were observed when significant amounts of secondary phases formed, notably at pH 2 to 3, and for longer-term batch experiments. Much of this concentration difference stems from the underestimation of the amounts of Al-phases formed at acid to near-neutral pH. Although an idealized rock composition was considered, the observed mismatch between model calculations and experimental data can be attributed to inadequate mineral precipitation reaction rates and a poor description of reactive surface areas in existing geochemical modelling codes. More accurate quantification of precipitation kinetics, including nucleation and growth, and improved descriptions of the temporal change of mineral surface area would enhance the predictive capabilities of reactive transport models and benefit, particularly, the efforts aimed at increasing the sustainability of EGS reservoirs.

58 GEOSCIENCES↗
DOE OSTI2021

Magmatic, hydrothermal and ore element transfer processes of the southeastern Archean Superior Province implied from electrical resistivity structure

Although magmatic- and metamorphic- derived fluids are widely recognized mineralizing agents, the role of crustal architecture in defining source and sink zones within the middle to lower crust and upper mantle of ancient orogens remains enigmatic. The globally largest and best-preserved Archean greenstone belts lie in the Superior Province, Canada. They provide an ideal location to investigate the influence of igneous construction and subsequent syn-deformational plutonism and metamorphism on the localization of metal-rich melts and fluids throughout the crustal column. Integration of three-dimensional magnetotelluric modelling and seismic reflection sections across the Abitibi subprovince reveals details of a 'whole-of-crust' magmatic and hydrothermal system. East-west low resistivity structures broadly underlie the surface traces of the major deformation zones that are host to significant gold endowment (>200 Moz), while mid-crustal cross trends suggest mineralized fluids flowed along 'pipes' within fault planes. Most low resistivity structures are inferred to represent domains containing interconnected zones of graphite and/or sulfide. Furthermore, these delineate relict mantle source/transit domains and crustal pathways enriched by the flow of magmas or metamorphic fluids genetically related to a late-stage pulse of ore-bearing magmatism, possibly as a result of slab break-off or delamination. Using the combined MT and seismic data, we develop a 3-D crustal-scale model which highlights how evolving orogenic architecture-controlled mass transfer and metallogenic processes developed.

58 GEOSCIENCES↗
DOE OSTI2025

Co-depolymerization of lignin and plastic waste using hydrothermal liquefaction process

Sustainable valorization of underutilized lignin and plastic waste beyond incineration is critical for producing renewable fuels. Hydrothermal liquefaction (HTL) provides a promising approach to convert wet lignin and plastics into high-quality oils without the need for prior drying of wet lignin. Here, this study examines the effects of temperature (300–400 °C), residence time, and polymer molecular weight on product yield and composition during HTL of polyethylene (PE), polypropylene (PP), and lignin under subcritical and supercritical water conditions. For PE, oil yields increased with temperature, with low molecular weight (LMW) PE achieving a maximum of ∼93 % at 400 °C for 30 min, while high molecular weight (HMW) PE reached ∼86 % at 400 °C for 1 h. Lignin and PP exhibited optimal oil yields at intermediate temperatures, decreasing at higher temperatures due to secondary reactions and char formation. Lignin yielded a maximum of ∼22 % oil at 300 °C for 30 min, LMW PP ∼88 % at 375 °C for 1 h, and HMW PP ∼83 % at 400 °C for 1 h. GC–MS analysis revealed that lignin oils were rich in phenols and alkylphenols, while PE and PP oils were dominated by paraffins and olefins. Oxygenated compounds in PE decreased at higher temperatures, improving oil quality. Co-liquefaction of lignin with plastics enhanced oil yields and energy content under specific conditions, demonstrating synergistic effects dependent on plastic type, molecular weight, and HTL conditions. These findings highlight the potential of HTL to produce high-energy, value-added fuels from lignin–plastic mixtures.

09 - BIOMASS FUELS↗
DOE OSTI2023

The impact of feedstock size and composition on the hydrothermal growth of (U,Th)O 2

Bulk crystal growth of refractory oxides requires unique approaches, and the U x Th 1-x O 2 solid solution is no exception. Hydrothermal transport reactions of U 0.1 Th 0.9 O 2 onto ThO 2 seeds with feedstocks comprised of U 0.1 Th 0.9 O 2 or mixtures of UO 2 and ThO 2 with a nominal composition of U 0.1 Th 0.9 O 2 are investigated with µ-Raman spectroscopy and X-ray fluorescence. In each case, the trends in stoichiometry as a function of distance from the seed are analyzed and the deviations from the nominal stoichiometry discussed. When the feedstock is composed of mixed oxides, the particle surface area’s influence on the feedstock dissolution rate is the dominant factor and can produce U-rich stoichiometries as high as U 0.75 Th 0.25 O 2 . When composed solely of U 0.1 Th 0.9 O 2 , the total growth amount depends on the particle size, but the obtained stoichiometry is the product of differing solubilities. Although the U0.1Th0.9O 2 feedstock produces the most homogeneous growth, the ending growth of the smallest particle UO 2 /ThO 2 mixture yields the stoichiometry closest to U 0.1 Th 0.9 O 2 . How to obtain desired stoichiometries from mixtures by matching the particle size and solubilities is briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Process intensification in hydrothermal liquefaction of biomass: A review

Hydrothermal liquefaction (HTL) presents a promising pathway for converting wet biomass resources into biofuels, offering significant advantages over conventional methods. However, numerous challenges must be addressed for HTL scale-up, including energy provision for the endothermic process, heat and mass transfer limitations, slurry concentration and pumpability challenges, char and coke formation, and continuous phase separation. This review explores key strategies such as autothermal HTL, which improves process efficiency and reduces external energy requirements by coupling exothermic and endothermic reactions within the same reactor, thereby simplifying reactor design and reducing operational costs. Additionally, multistage HTL processes are highlighted for their ability to optimize biocrude quality and yield by fractionating biomass conversion stages, resulting in higher energy returns on investment and better-quality biocrude. Solvothermal HTL and integration techniques for aqueous phase are also discussed. Furthermore, the HTL patent landscape is discussed to provide insights into current technological advancements. This review aims to offer a comprehensive understanding of process intensification in HTL, highlighting innovative solutions to enhance the efficiency and scalability of the process for sustainable biofuel production.

Biocrude oil↗
DOE OSTI2020

Hydrothermal reactivity of neutron absorber composites

The stability of neutron absorber composite materials at hydrothermal conditions was tested in a series of two-week experiments to mimic spent nuclear fuel disposal. Coupons, composed of boron carbide (B 4 C) sintered with and encased in aluminum, were increasingly altered in experiments at 150, 230, and 300 °C and pressures of 150 bar. Alteration of aluminum to boehmite (γ-AlO(OH)) and hydrogen gas generation occurred over the range of investigated temperatures, but is most significant at 300 °C. We found that the formation of boron-bearing mineral phases was not detected; however, aqueous boron was present in the reaction fluids.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Hydrothermal corrosion of laser printed SiC fibers under extreme environment

We report SiC/SiC fiber composites are proposed cladding materials to improve the accident tolerance of commercial light water nuclear reactor fuel. To evaluate their viability, understanding the kinetics of corrosion under irradiation and high-temperature, high-pressure aqueous environment is critical. In the present work, the microstructure and mechanical properties of novel SiC fibers manufactured by Laser Chemical Vapor Deposition (LCVD) are introduced. The LCVD technology has control over microstructure and stoichiometry while allowing for high purity manufacturing, all key qualities needed in search of an optimum SiC fiber for nuclear energy applications. The isolated hydrothermal corrosion of commercially available carbon-rich Hi-Nicalon Type-S fibers is compared to the LCVD stoichiometric and LCVD silicon-rich fibers. Autoclave testing was carried out at 310°C and 14 MPa in the absence of irradiation. In a separate study, the effect of gamma irradiation on the fibers in the room-temperature environment was analyzed. It was observed from the experiments that the dissolution of the fibers was highly dependent on the stoichiometric ratio, fiber surface morphology and thermal pre-treatment of fibers. Contrary to previous findings, fiber dissolution was also visible under low-temperature gamma irradiation in aqueous environment with LCVD fibers showing lower dissolution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hydrothermal corrosion and steam oxidation behavior comparison of UAM and conventional Zry-4

Here, hydrothermal corrosion and steam exposures on ultrasonic additively manufactured (UAM) Zircaloy-4 (Zry-4) specimens were conducted to compare to wrought Zry-4 performance in both simulated pressurized water reactor (PWR) operation (330°C, 15 MPa, <50 ppb oxygen, 500h) and representative accident conditions (100% H 2 O(g) at 700, 900, and 1100°C for up to 1h). UAM Zry-4 specimens showed 50% higher mass gain in PWR conditions and 50-80% more mass gain in steam oxidation due to internal oxidation between build layers in both cases. UAM Zry-4 in 900°C steam showed breakaway oxidation leading to sample deformation. Titanium used as an interlayer in the UAM process was detected in the substrate after the 1100°C exposure. Additional experiments to better link as-built defects to oxidation behavior are needed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hydrothermal synthesis of Co-free NMA cathodes for high performance Li-ion batteries

Scalable and sustainable production of high voltage cathodes is required to meet the increasing demands for Li-ion batteries. Additionally, the anticipated scarcity of critical materials like cobalt necessitates demonstration of Co-free alternatives that can match the performance metrics of conventional cathodes. Herein, a hydrothermal synthesis route for production of a new class of high-capacity, cobalt-free cathode material, LiNi 0.9 Mn 0.05 Al 0.05 O 2 (NMA9055) for next-generation Li-ion batteries is reported. In this work, the synthesized cathode material shows high crystallinity and purity with monodispersed spherical morphology. Extensive electrochemical, structural, and post-mortem characterization of this novel NMA material is carried out. NMA-Li half cells show an initial discharge capacity of 200 mAh/g with a 96% capacity retention over 100 cycles when cycled between 3.0 and 4.4 V. On the other hand, NMA full cells with Li 4 Ti 5 O 12 (LTO) electrodes as the anode, show an initial discharge capacity of 186 mAh/g with 81% capacity retention over 200 cycles. Post-mortem structural and morphological characterization show that the NMA morphology and crystal structure do not degrade significantly over 200 charge/discharge cycles. This new class of cobalt free cathode material containing nickel, manganese and aluminum synthesized by an ammonia-free synthesis route is expected to provide a facile solution towards sustainable cathode production.

25 ENERGY STORAGE↗
DOE OSTI2024

Mild chemical recycling of carbon fiber-reinforced epoxy composites in aqueous buffers and development of hydrothermally recyclable vitrimer composites from recyclates

Carbon fiber-reinforced polymer (CFRP) composites have gained widespread adoption across diverse industries. However, their inherent stability, stemming from the crosslinked structure of the matrix resin, poses a significant challenge in managing the growing volume of CFRP waste. Consequently, there is a pressing need for an eco-friendly upcycling method that effectively recovers and reuses both the valuable carbon fibers and the polymer matrix from CFRP waste. This study presents a novel approach for upcycling CFRP waste under environmentally friendly conditions. Firstly, CFRP waste with an amine-cured epoxy matrix was completely decomposed in aqueous buffer solutions under mild conditions (≤ 220 °C, pH = 4.8). Further, decomposed matrix polymer (DMP) was employed to transform conventional epoxy resins into recyclable vitrimers. Lastly, new composites that can be hydrothermally recycled were fabricated using both DMP and recovered carbon fibers. As a result, this work proposes a novel strategy for achieving a circular economy within the CFRP industry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Electrocatalytic oxidation of hydrothermal liquefaction-derived aqueous phase for on-site wastewater treatment and H 2 production

Electrocatalytic oxidation (ECO) is a promising method for generating molecular hydrogen (H 2 ) while simultaneously treating the aqueous phase (AP) from hydrothermal liquefaction (HTL) of biomass-derived feedstocks such as algae, food waste, sludge, and wood. This study highlights the impact of HTL-AP composition on ECO performance, mainly activity, stability, and efficiency in a batch and flow electrolyzer. We demonstrated current efficiency (CE) for chemical oxygen demand (COD) removal ranges from 14% to 85% in the flow electrolyzer with electrode stability increasing from 20 to ≥2,800 h. Decreasing the applied potential enhances the CE. High ammonium content can accelerate deactivation, yet chloride ions appear to aid oxidation of organic compounds and enhanced anode stability. A preliminary energy and H 2 balance for an HTL sewage sludge plant shows that the HTL-AP contains sufficient COD to produce all the H 2 needs for bio-oil hydrotreating, with a 26% surplus available for other uses.

Electrolysis↗
DOE OSTI2025

Mild Hydrothermal Crystal Growth of Two Luminescing Uranyl Phosphates Exhibiting an Autunite-Type Sheet Structure

Two new layered uranyl phosphate compounds, K(UO 2 )PO 4 (H 2 O) 3 and Na(UO 2 )PO 4 (H 2 O) 1.52 , crystallizing in an autunite-type sheet structure, were successfully synthesized as both single-crystals and polycrystalline powders under mild hydrothermal conditions. The compound K(UO 2 )PO 4 (H 2 O) 3 crystallizes in the tetragonal crystal system with the space group P4/ncc, exhibiting lattice parameters of a = b = 6.99320(7) Å and c = 17.8389(3) Å. Similarly, Na(UO 2 )PO 4 (H 2 O) 1.52 also crystallizes in the tetragonal crystal system, however, in the space group P4/nmm and exhibits lattice parameters of a = b = 6.9787 Å and c = 8.6303(17) Å. Both compounds adopt layered structures, a characteristic feature of uranyl phosphates, and exhibit intense green fluorescence typical for uranyl-containing materials. As a result, the infrared spectroscopy, photoluminescence, and scintillation properties of these compounds were investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Toward Sustainable Lithium Recovery: A Universal Hydrothermal Approach for Lithium Extraction

The rapid growth of lithium-ion battery (LIB) deployment presents critical challenges in sustainable end-of-life management and raw material recovery. Conventional pyrometallurgical and hydrometallurgical methods suffer from high energy demand, lithium loss, and complex wastewater treatment. This study established a universal, highly efficient, and sustainable hydrothermal route for lithium extraction and material recovery from various spent lithium-ion battery cathodes using 1,2,4,5-benzenetetracarboxylic acid (BTCA). The optimized process achieved over 99% lithium leaching efficiency for lithium iron phosphate (LFP) and LiNi x Mn y Co 1–x–y O 2 (NMC), with transition metal coleaching below 1%. It was also broadly applicable to lithium manganese oxide, lithium cobalt oxide, and black mass, achieving 98.5%, 98.95%, and 94.06% leaching efficiencies, respectively. The extracted lithium was directly converted into battery-grade lithium sources, while transition metals were recovered as oxides. Unreacted BTCA was efficiently regenerated and reused without degradation. Electrochemical evaluation confirmed that cathode materials synthesized with recovered lithium exhibit comparable performance to commercial products. Compared to conventional hydrometallurgy, the BTCA-based process increased revenue by over 40% and reduced greenhouse gas emissions by up to 39%. This closed-loop, chemistry-agnostic strategy offered a scalable and economically viable solution for industrial LIB recycling, enabling resource circularity and reducing dependency on primary critical materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Synergistic Interactions During Co-Hydrothermal Liquefaction of Food Waste and Biomass Model Compounds for Increased Sustainable Aviation Fuel Production

Hydrothermal liquefaction (HTL) of lignocellulosic biomass is plagued with low biocrude yields owing to the tendency of highly reactive oxygenated intermediates to condense to form biochars. By contrast, the high protein content in food waste is comprised of substantial nitrogen species, which are known to interact strongly with oxygenates through Maillard, amide, and peptide bond formation reactions. Co-feeding food waste and lignocellulose opens new reaction pathways for biocrude formation but is currently poorly understood. This work evaluated the molecular level interactions between food waste and lignocellulose model compounds and the corresponding effect on product yields and quality. Food waste–cellulose and food waste–xylan feedstock blends achieved maximum biocrude carbon yield improvements of 12.2% and 10.1%, respectively, relative to a simple linear model that interpolates between the yields of the pure feedstocks. Increases in biocrude yield were balanced by corresponding decreases in char yield, indicating synergistic interactions between the feeds during HTL. Biocrude volatility analysis revealed that increased biocrude yield preferentially benefitted the jet fuel fraction, which comprised up to 22.6% of the total carbon yield for food waste–cellulose blends. Biocrude and char were analyzed using GC–MS and FT-IR spectroscopy to investigate the source of synergistic trends and provide greater mechanistic understanding. Key cofeeding effects included the promotion of retro-aldol condensation reactions and trans-esterification of fatty acids, sequestering carbon in the biocrude phase via the inhibition of char formation while increasing biocrude volatility toward jet fuel-range compounds. These results indicate the potential for judicious selection of HTL cofeeds to increase both biocrude yield and selectivity to desired fuel precursors, including sustainable aviation fuel.

Maillard reaction↗
DOE OSTI2021

Transformation Kinetics of Phosphorus and Nitrogen in Iron-Rich Sewage Sludges during Hydrothermal Treatment and Recovery of Nutrients from Process Water

Hydrothermal treatment (HT) is an emerging technique for sustainable sewage sludge management and resource recovery. Many sludges are rich in iron (Fe) due to the common addition of Fe salts in water resource recovery facilities. To develop guidance for reaction conditions targeting nutrient recovery, this study systematically investigated the influence of HT temperature, treatment time, and sludge source on the dynamic speciation evolution of phosphorus (P) and nitrogen (N) during HT of Fe-rich sewage sludge. Complementary chemical extraction and X-ray spectroscopy analyses were conducted to characterize the treatment products. For the sludge mixture (a blend of primary and waste activated sludges), P speciation did not change significantly within 4.5 h at 125 °C HT, while soluble and labile P was converted into insoluble P over time at 175 and 225 °C HT. Strengite (FePO 4 · 2 H 2 O) preferentially formed in the hydrochars with increasing treatment temperature and/or time, whereas 125 °C HT within 1.5 h favored the formation of vivianite (Fe 3 (PO 4 ) 2 ·8H 2 O). Organic P was completely decomposed into orthophosphate when the HT temperature reached up to 175 °C. Pyrrole-N was enriched in the hydrochars. Similar reaction pathways were observed during HT of anaerobically digested sludge, though some minor differences in Fe-associated P and organic P were observed. Meanwhile, HT of the two sludges released orthophosphate and ammonia into the process waters at 175 and 225 °C, which can be recovered by a sequential process involving struvite (MgNH 4 PO 4 ·6H 2 O) precipitation and air stripping. This study provides new insights into the transformation of P and N during HT of Fe-rich sludges as well as a modular design for maximum P and N recovery from the treatment products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Roadmap for Deployment of Modularized Hydrothermal Liquefaction: Understanding the Impacts of Industry Learning, Optimal Plant Scale, and Delivery Costs on Biofuel Pricing

Hydrothermal liquefaction (HTL) is a promising technology for converting abundant organic wastes into fuels. Previous techno-economic analyses (TEAs) of HTL have been used to estimate the minimum fuel selling price (MFSP) of biofuel products, but these analyses often assume a bespoke plant design where each plant operates under unique process conditions and neglect transportation costs. However, transportation costs must be included in realistic TEAs, and further, a mass-produced fixed-scale modular plant design approach may be more effective than case-by-case plant design, provided that there is sufficient market capacity to benefit from modularization. This study estimates fuel price behavior in the presence of transportation costs and benefits stemming from modular plant design. This analysis indicates that a modular process capable of handling 60 dry tons per day (DTPD) is optimal, resulting in a ~25% reduction in MFSP (from $4.70/GGE, fully upgraded) at complete market feedstock utilization compared with case-by-case design. The associated cost reductions are attributable to learning benefits and modularization. Several HTL deployment “roadmaps” are then explored, with each roadmap consisting of different periods of case-by-case design followed by adoption of a modularized approach. A period of nonmodular industry growth up to market saturation of ~7% followed by implementation of modular plant design strikes a balance between the investment risk and learned cost reductions associated with modular plant design. However, if bespoke plants built during this period of nonmodular growth saturate more than 23% of available feedstock, learned cost reductions are significantly diminished. Here, this study points to the potential benefits of modularized and decentralized waste-to-energy processes when the modularization follows an optimal deployment strategy.

09 BIOMASS FUELS↗