Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “grain boundary segregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Influence of microstructure and temperature on impact toughness of H13 steel produced by binder jet additive manufacturing

Binder Jet Additive Manufacturing (BJAM) is a promising manufacturing pathway to produce H13 steel dies and tooling with complex geometries for applications in high pressure aluminum die casting, hot stamping, and injection molding. While fully dense H13 coupons produced using BJAM have been subjected to detailed microstructure characterization, properties which are critical and relevant to the aforementioned applications, such as impact toughness, have not been reported. Here, this work evaluated the influence of microstructural characteristics and test temperature on the impact toughness of H13 produced by BJAM. Coupons were produced from three different powder size distributions (PSDs), with nominal powder size ranges of −22 μm, 10-32 μm, and 15-53 μm. Coupons were printed, sintered, hot isostatically pressed (HIPed), and heat treated by quenching and tempering. After HIPing, the measured porosities of the different PSDs were all less than 0.015 vol%. The −22 μm PSD BJAM material exhibited the best impact toughness of all three PSDs across the entire test temperature range from 25 to 400 °C, and also exhibited an ambient temperature impact toughness of 10.9 J at a hardness of 46 HRC, equivalent to minimum threshold requirements for premium grade H13. However, all three BJAM PSDs exhibited moderately lower impact toughness than premium grade wrought H13 from RT to 400 °C. We attribute this in part due to the very large prior-austenite grain (PAG) sizes near 400 μm and segregation from former liquid channels leading to greater amounts of carbide precipitation on PAG boundaries. Technical pathways for optimizing processing and chemistry of BJAM H13 to further improve impact toughness are discussed.

Binder jet additive manufacturing↗
DOE OSTI2020

Synthesis routes to eliminate oxide impurity segregation and their influence on intergrain connectivity in K-doped BaFe 2 As 2 polycrystalline bulks

The poor reproducibility of intergrain critical current density $J_c$ in Fe-based superconductors is often believed to result from uncontrolled grain boundary (GB) connectivity degraded by extrinsic factors such as the local or global impurity concentration or GB porosity or cracks. Earlier we found that Ba and K can appear as oxide impurities at GBs, along with GB-wetting FeAs. In this study, we evaluated how the sample preparation environment and purity of the starting materials influence the polycrystalline $J_c$ in K-doped BaFe 2 As 2 (Ba122) bulks. Using a high-performance glovebox, the oxygen and water levels were significantly reduced, eliminating traces of FeAs. We report oxide impurities and Ba (or K) segregation associated with oxygen in the starting materials were significantly reduced by using high purity starting materials. This combination essentially doubled the best $J_c$(4.2 K) values to 2.3 × 10 5 at self-field and 1.6 × 10 4 A cm –2 at 10 T and analytical scanning transmission electron microscopy showed no GB or O segregation in the best samples, but did show dark Z-contrast and distinct nanoscale porosity. Our work shows that an inert synthesis environment and high purity K and Ba do reduce current-blocking oxygen impurity and GB impurity phases, allowing deeper exploration of the role of extrinsic and intrinsic GB blocking effects in controlling the $J_c$ of polycrystalline Ba122.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Hierarchical Defect Engineering for LiCoO 2 through Low-Solubility Trace Element Doping

Real-world industry-relevant battery composite electrodes are hierarchically structured. Their structural and chemical complexity is featured by ubiquitous multi-scale porosity and cracks, solid-solid and solid-liquid interfaces, compositional and redox heterogeneity, as well as lattice disordering and deformation. In particular for the active cathode particles, which are the fundamental building blocks for the energy reservoir, it is a consensus that these structural and chemical defects could have a profound impact on the battery performance. An in-depth understanding of the underlying mechanisms could critically inform the cathode material engineering, which would have a tremendous potential but remains a daunting challenge at present. In this work, we tackle this question by studying LiCoO 2 (LCO) with trace doping of Ti, which exhibits a low solubility in the LCO layered lattice. Additionally, we observed the spontaneous and heterogeneous segregation of the dopant (Ti) across a wide range of length scales. In addition to the modification of the particle surface and the buried grain boundaries within the particle, we reveal that the Ti doping has induced a significant amount of lattice distortions, which, in turn, promotes the robustness of the LCO lattice at high state of charge (above 4.5V). Our result formulates a multi-scale defect engineering strategy that could be applicable to the synthesis of a broad range of energy materials for applications in batteries and beyond.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Kinetics of amorphous defect phases measured through ultrafast nanocalorimetry

Recognition of the role of extended defects on local phase transitions has led to the conceptualization of the defect phase, localized thermodynamically stable interfacial states that have since been applied in a myriad of material systems to realize significant enhancements in material properties. Here, we explore the kinetics of grain boundary confined amorphous defect phases, utilizing the high temperature and scanning rates afforded by ultrafast differential scanning calorimetry to apply targeted annealing/quenching treatments at high rates capable of capturing the kinetic behavior. Four Al-based nanocrystalline alloys, including two binary systems, Al–Ni and Al–Y, and two ternary systems, Al–Mg–Y and Al–Ni–Y, are selected to probe the materials design space (enthalpy of mixing, enthalpy of segregation, chemical complexity) for amorphous defect phase formation and stability, with correlative transmission electron microscopy applied to link phase evolution and grain stability to nanocalorimetry signatures. A series of targeted isothermal annealing heat treatments is utilized to construct a Time–Temperature-Transformation curve for the Al–Ni system, from which a critical cooling rate of 2400 °C/s was determined for the grain boundary confined disordered-to-ordered transition. Finally, a thermal profile consisting of 1000 repeated annealing sequences was created to quantify the recovery of the amorphous defect phase following sequential annealing treatments, with results indicating remarkable microstructural stability after annealing at temperatures above 90% of the melting temperature. This work contributes to a deeper understanding of grain boundary localized thermodynamics and kinetics, with potential implications for the design and optimization of advanced materials with enhanced stability and performance.

Amorphous defect phases↗
DOE OSTI2021

Elemental segregation to lattice defects in the CrMnFeCoNi high-entropy alloy during high temperature exposures

The influence of small plastic pre-strains on the elevated-temperature stability and microstructure of the equiatomic CrMnFeCoNi FCC solid solution is investigated. Particular attention is given to whether any of the alloy elements segregate to individual dislocations. To that end, CrMnFeCoNi samples were first deformed in tension at room temperature to plastic strains of 0.2 and 2.3%, and subsequently annealed at 973 K for 800 hours. The pre-strains activated planar slip of 1/2<110>-type dislocations on {111}-type glide planes. Interactions of this planar slip with special Σ3 grain boundaries formed a large number of dislocation segments with a <110>-type crystallographic orientation suitable for a credible end-on analysis of dislocation cores in HR-STEM. The cores of the 1/2<110> dislocations pushed up against the investigated grain boundaries were found to be close to the compact configuration. Within the sensitivity of the Super-X EDS mapping, no concentration gradient was detected near dislocations that would indicate enrichment at dislocation cores of any of the elemental constituents of the alloy after the pre-deformation and annealing. However, a Cr-rich tetragonal sigma phase nucleated and grew at grain boundary triple junctions during this anneal, processes that were not accelerated by the enhanced dislocation density present after pre-strain. A clear chromium gradient was observed in the Cr-depleted zones near grain boundaries suggesting that Cr transport occurred by relatively slow diffusion from the bulk to the grain boundaries and then by relatively fast diffusion along the grain boundaries to the precipitates. Accompanying the Cr depletion near grain boundaries is a simultaneous Ni and Mn enrichment, which promotes formation of the L1 0 NiMn phase that is observed on the grain boundaries after prolonged annealing.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Influence of Powder Characteristics and Processing Methods on Creep Performance of Powder Metallurgy Hot Isostatic Pressed SS316

The U.S. nuclear energy expansion goals are driving the demand for manufacturing routes that can rapidly produce large, complex, near net shape components. Powder metallurgy hot isostatic pressing (PM HIP) is an advanced manufacturing technique that can be economically scaled-up, while alleviating the supply chain challenges that forging and casting face in terms of cost and lead time constraints. This makes PM-HIP a viable technology to aid and accelerate large-scale part manufacturing for nuclear applications. However, large-scale qualification and deployment of this technology require a thorough understanding of the influence of powder feedstock quality, powder handling history, hot isostatic pressing (HIP) parameters, and subsequent heat treatment on microstructural evolution and elevated temperature mechanical performance. The present work focusses on 316 austenitic stainless steel (SS316) which is most commonly used in high temperature environments for nuclear applications Results from this study show that PM HIPed SS316 meets ASME tensile requirements at room temperature and at elevated temperature. However, creep performance of PM-HIPed SS316 remains inferior to its wrought counterpart, demonstrating that tensile performance alone is not a reliable metric for long duration high temperature integrity. Further, this report delineates powder derived microstructural features that govern creep damage, with key evidences pointing to “microstructural inheritance” from gas atomized powder feedstocks. Commercial SS316 powders of varying chemical compositions and recycling histories were studies, and the results showed large differences in elemental segregation, oxide surface layers and secondary phase distributions. Multi-scale characterization revealed segregation of chromium, molybdenum, manganese and silicon at the boundaries and the precipitation of manganese-, silicon-, and molybdenum-oxides. During HIP consolidation, these surface oxides transform into decorated prior particle boundaries (PPBs) and grain boundary inclusions that persist through conventional post-HIP solution annealing treatment. The retained oxides in post-HIP microstructures were found to influence grain growth, precipitation behavior, and ultimately creep cavitation and fracture. Such post-HIP heat treatments are therefore limited by a complex trade-off between grain growth, and oxide coarsening which aggravate creep damage by acting as nucleation sites for cavities. The objective of this work is to establish an integrated processing–structure–property framework for PM-HIP 316 stainless steel by investigating the influence of powder feedstock characteristics in pre- and post-HIP processing as well as to understand the significance of post-HIP heat treatment on microstructural evolution and creep properties. The results from this report emphasize the significance of powder feedstock integrity in improving creep performance of PM-HIPed SS316, by highlight the effect of rapid solidification, elemental segregation, oxide formation and powder recycling on microstructural defect inheritance following HIP consolidation. Rather than considering HIP processing, solution annealing, and mechanical performance independently, this report treats powder production, HIP consolidation, post-HIP thermal processing, and creep deformation as interconnected stages within a continuous metallurgical process. The resulting framework will provide a scientific basis for developing feedstock engineering strategies capable of improving long-term reliability of PM-HIP stainless steels and accelerating their qualification for advanced nuclear applications.

Ajjarapu, Pavan [Oak Ridge National Laboratory (OR↗
DOE OSTI2022

Carbon nanotube (CNT) reinforced 316L stainless steel composites made by laser powder bed fusion: Microstructure and wear response

Carbon nanotube (CNT) reinforced 316L stainless steel (SS) composites were fabricated by laser powder bed fusion (LPBF) additive manufacturing (AM). This study focuses on microstructure evolution, hardness, and wear behavior. The wear behavior for AM 316L SS and 1 wt% CNT/316L SS was studied by a dry sliding test under normal loads of 10, 15, and 25 N. The addition of CNT to 316L SS led to the change of solidification mode from cellular/columnar to dendritic growth, producing grain refinement. Nanoscale dendrites were observed. Although TEM characterization confirmed the existence of CNT in cell interior, most CNT were damaged, resulting in carbon material segregation along cellular/dendritic boundaries. The wear rate was found dramatically decreased due to the improved hardness. Compared to the adhesive and abrasive wear in AM 316L SS, the wear mechanism of CNT/316L composite was adhesion and oxidative wear. Furthermore, enhanced cellular/dendritic boundary strengthening by carbon segregation was the main strengthening mechanism of CNT/316L composite.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hot Forging Options for Thick Castings

Uranium alloyed with 10 wt% molybdenum (U-10Mo) is a monolithic nuclear fuel relevant to the National Nuclear Security Administration’s nonproliferation efforts. Research has been underway to optimize processing techniques for the U-10Mo fuel. This study investigated the use of hot compression or “hot forging” on a thick (~1") cast and homogenized U-10Mo plate before standard hot and cold rolling procedures. After plates were cast and homogenized, six samples were cut and forged at 700°C at a strain rate of either 0.10 s –1 or 0.01 s –1 at six levels of reduction. After forging, all samples underwent hot and cold rolling followed by annealing to achieve a final foil thickness of about 0.0085". Samples were taken at each stage of the casting and thermomechanical processing to assess the microstructural evolution. Chemical composition, microstructure, and uranium carbide morphology are presented and assessed in this study. Upon hot forging, dislocations accumulate along the grain boundaries, which serve as nucleation sites for randomly oriented, strain-free grains during subsequent annealing steps. Hot forging and subsequent annealing produced very heterogeneous grain sizes. However, no molybdenum segregation was observed after forging. No obvious trend was observed between forging conditions (strain rate and reduction percentage) and the microstructure after final thermomechanical processing. Upon hot rolling to 0.04" and annealing (700°C for 45 min), the average grain diameters from OM was 17 ± 2 µm across the six different forged samples. The subsequent cold rolling to 0.0085" and then annealing (700°C for 45 min) resulted in an average of 13 ± 2 µm between the six samples. Thus, the starting, as-forged microstructure did not appear to significantly influence the final microstructure of the cold-rolled foil. These results will help with understanding and expanding hot working capabilities for thicker U-10Mo castings. They also provide useful information on the effects of hot forging and its potential use to minimize defects that can arise during subsequent hot and cold rolling procedures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Modified microstructures in proton irradiated dual phase 308L weldment filler material

In this study, the effect of proton irradiation on the microstructure of δ ferrite—γ austenite mixed phase 308L filler material in a 508–304 dissimilar metal weldment was investigated over a depth of 0 to 10 µm. Ni–Si–Mn G-phase precipitates were observed with SEM and TEM in δ ferrite but not in γ austenite. Our density functional theory based calculations show that the G/Fe interface energy in δ-Fe is significantly lower than that in γ-Fe (0.35 versus 1.25 J/m 2 ), which provides a thermodynamics-based explanation for our experimental observations of preferential formation of G-phase in δ ferrite. STEM-EDS, TEM dark field imaging, and diffraction patterns confirmed the Ni–Si–Mn enriched precipitates were G-phase precipitates with a stoichiometry of Mn 6 Ni 16 Si 7 . Intragranular voids and Ni–Si enriched clusters were observed in irradiated γ austenite. Additionally, Ni and Si segregation was observed along the void interfaces. In both cases, Ni–Si clusters and segregation to voids, selected area diffraction patterns did not reveal the existence of a second phase. Proton irradiation induced Cr depletion and Si and Ni enrichment at γ-γ austenite grain boundaries that was characterized with STEM/EDS.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1997

Sulfur Impurities and the Microstructure of Alumina Scales

The relationship between the microstructure of alumina scales, adhesion, and sulfur content was examined through a series of nickel alloys oxidized in 1100 to 1200 deg. C cyclic or isothermal exposures in air. In cyclic tests of undoped NiCrAl, adhesion was produced when the sulfur content was reduced, without any change in scale microstructure. Although interfacial voids were not observed in cyclic tests of NiCrAl, they were promoted by long-term isothermal exposures, by sulfur doping, and in most exposures of NiAl. Two single crystal superalloys, PWA 1480 and Rene' N5, were also tested, either in the as-received condition or after the sulfur content had been reduced to less than 1 ppmw by hydrogen annealing. The unannealed alloys always exhibited spalling to bare metal, but interfacial voids were not observed consistently. Desulfurized PWA 1480 and Rene' N5 exhibited remarkable adhesion and no voidage for either isothermal or cyclic exposures. The most consistent microstructural feature was that, for the cases where voids did form, the scale undersides exhibited corresponding areas with ridged oxide grain boundaries. Voids were not required for spallation nor were other microstructural features essential for adhesion. These observations are consistent with the model whereby scale spallation is controlled primarily by interfacial sulfur segregation and the consequent degradation of oxide-metal bonding.

Smialek, James L.↗
NASA NTRS1996

Microgravity Segregation in Binary Mixtures of Inelastic Spheres Driven by Velocity Fluctuation Gradients

We are interested in collisional granular flows of dry materials in reduced gravity. Because the particles interact through collisions, the energy of the particle velocity fluctuations plays an important role in the physics. Here we focus on the separation of grains by properties - size, for example - that is driven by spatial gradients in the fluctuation energy of the grains. The segregation of grains by size is commonly observed in geophysical flows and industrial processes. Segregation of flowing grains can also take place based on other properties, e.g. shape, mass, friction, and coefficient of restitution. Many mechanisms may be responsible for segregation; most of these are strongly influenced by gravity. Here, we outline a mechanism that is independent of gravity. This mechanism may be important but is often obscured in terrestrial grain flows. It is driven by gradients in fluctuation energy. In microgravity, the separation of grains by property will proceed slowly enough to permit flight observations to provide an unambiguous measurement of the transport coefficients associated with the segregation. In this context, we are planning a microgravity shear cell experiment that contains a mixture of two types of spherical grains. The grains will be driven to interact with two different types of boundaries on either sides of the cell. The resulting separation will be observed visually.

Jenkins, James T.↗
DOE OSTI2026

Thermodynamics of grain-boundary phases

The past decade has seen a significant increase in research efforts aimed at understanding the thermodynamics of low-dimensional phases existing in many materials systems, ranging from two-dimensional materials to core regions of extended defects in crystalline solids. We review the current status of theoretical, computational, and experimental research on the “defect phases,” focusing on grain boundaries (GBs) in elemental and multicomponent polycrystalline materials. After reviewing the generalized concept of a phase of any dimensionality, we discuss recent progress in atomistic computer simulations of GB phase transformations and phase coexistences, including the observation of one-dimensional defects separating GB phases (defects in defects). Computational predictions compare well with experimental observations of multiple GB phases and segregation-induced phase transformations. An intriguing open question of GB thermodynamics is whether the GB free energy can be driven to a zero value by increasing solute segregation. We review recent efforts to understand this ultimate thermodynamic stabilization of GB phases and the possible polycrystalline microstructures that may arise. An outlook for future research in the field is discussed.

Materials science↗
DOE OSTI2024

He bubble-induced phase transformation of W grain boundaries revealed by accelerated molecular dynamics

The growth of He bubbles and the resulting impact on the microstructural evolution of W are of paramount importance to the plasma-facing materials community due to the application of W in Tokamak fusion reactors. Using accelerated molecular dynamics (AMD) techniques, we outline the structural evolution of grain boundaries (GBs) caused by growing He bubbles. It is discovered that when an alternative, low energy, high density GB structure or phase is available, He bubbles can induce a progressive phase transformation of the GB to the higher density phase by the continual nucleation of W Frenkel pairs. Here, we find that the resulting W self-interstitials migrate to sites at the GB which are structurally related to the higher density phase, leading to the transformation. We discuss the implications of this progressive microstructural evolution on the growing He bubble and consider in general how He bubbles will impact the structural evolution of an arbitrary W GB. These findings of GB phase transformation are predicted to impact other damage events in W such as recrystallization, GB migration and defect segregation which must take these findings into account in order to accurately simulate a realistic W microstructure and hence extract experimentally meaningful data.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Non-Newtonian Convection and Compositional Buoyancy: Advances in Modeling Convection and Dome Formation on Europa

Numerical modeling of non-Newtonian convection in ice shows that convection controlled by grain boundary sliding rheology may occur in Europa. This modeling confirms that thermal convection alone cannot produce significant dome elevations. Domes may instead be produced by diapirs initiated by thermal convection that in turn induces compositional segregation. Exclusion of impurities from warm upwellings would allow sufficient buoyancy for icy plumes to account for the observed approximately 100 m topography of domes, provided the ice shell has a small effective elastic thickness (approximately 0.2 to 0.5 km) and contains low eutectic-point impurities at the few percent level.

Pappalardo, R. T.↗
NASA NTRS2000

Mineralogy, Petrology, Chemistry, and Ar-39 - Ar-40 and Ages of the Caddo County IAB Iron: Evidence for Early Partial Melt Segregation of a Gabbro Area Rich in Plagioclase-Diopside

We found coarse-grained gabbroic material rich in plagioclase and diopside in the Caddo County IAB iron meteorite. The polished thin sections studied were made from areas rich in Al and Ca detected by a micro-focus X-ray fluorescence (XRF) mapping technique. The gabbro is not a clast within a breccia, but rather this area is located mainly at silicate-metal boundaries only a few cm away from an area with fine-grained, ultramafic silicate similar to winonaites. Medium-grained orthopyroxene and olivine are found in transitional areas showing no disturbance of their crystalline textures. A vein-like region, starting at the area rich in fine-grained mafic silicate, extends towards the gabbroic area with a gradual increase in abundance of plagioclase and diopside. This texture and our accumulated knowledge of the formation mechanism of IAB/winonaltes meteorites, suggest that the gabbroic materials were formed by inhomogeneous segregation of partial melts of chondritic source materials. Compositional data on two mineralogically distinct samples of the gabbro-rich portion of the inclusion were obtained by INAA. Compared to an average of LAB silicate inclusions or winonaites, the Caddo County gabbro is enriched in the incompatible lithophile elements Na, Ca, Sc, REE and Hf, which is consistent with a melt origin for the gabbro. The cosmogenic space exposure age of Caddo County (511 Ma) is significantly younger than exposure ages of some other IAB meteorites, An 39Ar-40Ar age determination of the gabbroic material indicates a series of upward steps in age from 4.516 Ga to 4.523 Ga, with a few high temperature ages up to 4.54 Ga. The older age could approximate the primary recrystallization age of silicates. The stepped Ar age spectrum may indicate differences in Ar closure temperatures during slow cooling of -2-20'C/Myr in the parent body. Alternatively, the younger Ar-Ar ages may date a shock event which occurred while Caddo County was hot and which also created textures such as a linear metal vein with rounded zigzag walls in a diopside crystal and slightly miss-oriented rounded plagioclase domain.

Takeda, Hiroshi↗
DOE OSTI2021

Effects of low-temperature neutron irradiation on the microstructure and tensile properties of duplex 2304 stainless steel and its electron-beam welds

A lean duplex stainless steel material (2304-grade) in its base metal and electron beam (e-beam) welded conditions were studied microstructurally and mechanically as a function of irradiation conditions to evaluate its use as a structural material at low temperatures (60–100 °C). Neutron irradiation up to a fluence of 1.40 × 10 19 n/cm 2 (E > 0.1 MeV) or ~0.011 dpa decreased the total elongation of both base metal and e-beam welded samples. Overall, radiation hardening was observed in all the samples. The transversely cut irradiated samples showed some nonuniform quasi-cleavage and shearing in their fracture surfaces, indicating the variance of ductile nature of the two-phased (deformable austenite and harder ferrite) duplex structure. The e-beam welded samples also showed quasi-cleavage fracture, which is a characteristic of radiation-induced embrittlement. Furthermore, these observations of the e-beam welded samples were attributed to the formation of coarse ferrites, grain boundary and intragranular phases such as γ 2 and γ 3 , and minor impurity phases such as CrN and Cr 2 N in the weld pool and/or heat-affected zone of the samples. Radiation-induced elemental segregation was also identified in the post-irradiated base metal.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rapid Solidification Effects in Additively Manufactured Si and SiGe Compositions

SiGe alloys have a proven track record as robust high-temperature thermoelectric materials, powering NASA missions like SNAP-10A, LES-9, and Voyager 1 and 2. Enhancing thermoelectric efficiency hinges on minimizing thermal conductivity while preserving electrical conductivity. Rapid solidification via LPBF can generate microstructural features such as subgrain cellular boundaries and twinning, which may help reduce thermal conductivity while preserving semiconducting behavior. Here, this study investigates the potential of laser powder bed fusion (LPBF) additive manufacturing to fabricate nanostructured Si and SiGe thermoelectric materials. High cooling rates (10 5 to 10 7 K/s) rates inherent to the LPBF process are conducive to forming such nanostructures. Moreover, this fabrication technique could also be suitable for fabricating complex geometries needed to achieve improved device level performance. Process mapping of commercial Si powder with irregular morphology was first performed to understand the LPBF processing behavior of this semiconductor material. Subsequent studies included in-house synthesized B-doped (p-type) Si7 8 Ge 22 spherical powder that was produced via ultrasonic atomization. Scan strategies involved multiple laser exposures to mitigate solidification cracking: a high density of >98% was achieved, but solidification cracking could not be fully eliminated. Subsequently, a high electrical resistivity (i.e., low conductivity) was observed, but the measured Seebeck coefficient, ∼230 μV/K @ 500 °C, proved that good semiconductor material was being fabricated. A subgrain cellular structure (5–10 μm) was observed as defined by Ge segregation to the intercellular boundaries. The remelting strategies helped lower the cooling rates in processing SiGe, but this still resulted in high residual stresses, which induced a remarkably high density of twins (78–95%) to accommodate the deformation. This unique grain structure offers an avenue for phonon scattering and potential improvements in thermoelectric performance.

figure of merit↗
NASA NTRS1986

Presence, segregation and reactivity of H, C and N dissolved in some refractory oxides

The sources of impurities, particularly carbon, in high melting oxides and silicates are discussed, along with detection and quantification methods. The impurities are important for their effects on bulk material properties through the media of, e.g., surface or grain boundary characteristics. The impurities are usually encountered by the contact of the oxide (refractory) material with volatiles such as H2O and CO2, which become incorporated in the material and form anion complexes with oxygen acting as a covalent bonded ligand. The specific processes undergone by MgO in assimilating C impurities are delineated, using data obtained with X-ray photoelectron spectroscopy, Auger electron spectroscopy, secondary ion mass spectrometry and nuclear reaction profiling. Finally, maintenance of a supersaturated solid solution with C impurities by space charge control is described as a means of offset impurity effects.

Freund, F.↗