Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “glycolization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 217 records · Page 12

Free-Charge Carrier Generation in Homojunction Non-Polymeric Organic Semiconductor Films - The Role of the Optical Frequency Dielectric Constant

Engineering the dielectric constant (..epsilon..) to lower the exciton binding energy of the light-absorbing semiconductor can improve organic photovoltaic (OPV) device performance. Here, a series of materials are reported with 2-(3-oxo-2,3-dihydro-1H-inden-1-ylidene)malononitrile (INCN) acceptor end groups and a central glycolated bis(4H-cyclopenta[2,1-b:3,4-b']dithiophene) unit with large low-frequency (..epsilon..lf = 7.4-7.9 at 0.1-0.2 MHz) and optical-frequency (..epsilon..opt up to 6.6 at 2 x 1014 Hz) dielectric constants. The INCN end groups differed in whether they were protonated, chlorinated, or fluorinated, with the latter having the highest ..epsilon..opt. An ..epsilon..opt of 6.6 is predicted to lead to a low exciton binding energy of ~0.04 eV. Time-resolved microwave conductivity measurements showed a temperature-dependent yield-mobility product, with it increasing linearly from 340 K. The onset temperature was near that required to overcome the calculated exciton binding energy and indicates increased free charge generation in a homojunction film. Room temperature transient absorption spectroscopy revealed that photoexcitation rapidly converted to a lower energy state that was consistent with the formation of polarons or a charge transfer state. This work provides experimental evidence of the importance of ..epsilon..opt for the generation of free charges, and a strategy for development of efficient single chromophore homojunction OPV devices.

charge generation↗

The effect of polymer grafting on the mechanical properties of PEG-grafted cellulose nanocrystals in poly(lactic acid)

Poly(lactic acid) (PLA) is a commercially available bio-based polymer that is a potential alternative to many commodity petrochemical-based polymers. However, PLA's thermomechanical properties limit its use in many applications. Incorporating polymer-grafted cellulose nanocrystals (CNCs) is one potential route to improving these mechanical properties. One key challenge in using these polymer-grafted nanoparticles is to understand which variables associated with polymer grafting are most important for improving composite properties. In this work, poly(ethylene glycol)-grafted CNCs are used to study the effects of polymer grafting density and molecular weight on the properties of PLA composites. All CNC nanofillers are found to reinforce PLA above the glass transition temperature, but non-grafted CNCs and CNCs grafted with short PEG chains (<2 kg mol –1 ) are found to cause significant embrittlement, generally resulting in less than 3% elongation-at-break. By grafting higher molecular weight PEG (10 kg mol –1 ) onto the CNCs at a grafting density where the polymer chains are predicted to be in the semi-dilute polymer brush conformation (~0.1 chains nm –2 ), embrittlement can be avoided.

36 MATERIALS SCIENCE↗

Imaging a solvent-swollen polymer gel network by open liquid transmission electron microscopy

Visualizing the network of a solvent-swollen polymer gel remains problematic. To address this challenge, open transmission electron microscopy (TEM) was applied to thin gel films permeated by a nonvolatile ionic liquid. The targeted physical gels were prepared by cooling concentrated solutions of poly(ethylene glycol) in 1-ethyl-3-methyl imidazolium ethyl sulfate [EMIM][EtSO 4 ]. During the cooling, gelation occurred by a frustrated crystallization of the dissolved polymer, leading to a percolated, solvent-permeated semicrystalline network in which nanoscale polymer crystals acted as crosslinks. Crystalline features ranging from ~5 to ~200 nm were observed, with the visible network strands dominantly consisting of long curvilinear crystallites of ~15–20 nm diameter. Nascent spherulites irregularly decorated the network, creating a complex structural hierarchy that complicated analyses. Lacking diffraction contrast, TEM did not visualize the many disordered, fully solvated PEG chains present in the voids between crystals. Finally, recognizing that a network's three dimensionality is ambiguous when assessed through two-dimensional microscopy projections, a small gel region was studied by TEM tomography, revealing a nearly isotropic three-dimensional arrangement of the curvilinear crystallites, which displayed remarkably uniform cylindrical cross sections.

36 MATERIALS SCIENCE↗

Improving the Recyclability of Polymer Composites With Cellulose Nanofibrils

Cellulose nanofibers (CNFs) have been widely studied for their reinforcing potential in high-performance composites. While there are numerous publications on CNF-reinforced composites in a variety of polymer matrices, few have considered the recyclability of such thermoplastic composites and whether the incorporation of CNFs deteriorates or improves their performance upon reprocessing. In this study, two thermoplastic resins, poly(lactic acid) (PLA), and glycol-modified polyethylene terephthalate (PETg), were prepared with CNF reinforcement and thermomechanically recycled to investigate the effect of CNF inclusion on the composite properties after reprocessing as well as their effect on the composites’ number of useful life cycles. Additionally, changes in mechanical, thermal, rheological, molecular, and microstructural properties of the composites and/or base resins were monitored as a function of cycle numbers. As is typical, the polymers’ molecular weight and mechanical performance deteriorated with continued processing. However, the addition of spray dried CNF was found to better maintain the mechanical performance of both polymers throughout multiple recycling steps as compared to neat samples. For example, the tensile strength of PETg with 20 wt% CNF after 6 processing cycles was found to exceed that of virgin neat PETg, and higher loadings of CNF were found to preserve a higher yield strength during multiple rounds of reprocessing compared to PETg composites with lower CNF loadings. Ultimately this study indicates that the addition of CNF to some thermoplastic materials can increase both their sustainability by offsetting the use of high-embodied energy resins and their circularity by enabling performance retention over more use cycles.

42 ENGINEERING↗

Biocompatible organosolv fractionation via a novel alkaline lignin-first strategy towards lignocellulose valorization

Simultaneous valorization of both carbohydrate and lignin fractions in lignocellulose remains a great challenge. Herein, a novel lignin-first strategy using triethylene glycol (TEG) under alkaline conditions for effective biomass fractionation producing highly digestible carbohydrates and reactive lignin was developed. Delignification was over 80% and fermentable sugar yields were close to 90% after pretreatment at 90°C. The biocompatibility of TEG allowed direct enzymatic hydrolysis of the solid residue without washing, thus minimizing wastewater generation. Furthermore, the obtained lignin (TEGL) had an uncondensed structure with well-preserved β-O-4 linkage, leading to near-equal aromatic monomer yields compared to cellulolytic enzyme lignin after catalytic-free pyrolysis, demonstrating high valorization potential. Finally, the proposed TEG solvent system is promising for a green and sustainable biorefinery process to achieve the complete utilization of lignocellulose.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Double in-situ lignin modification in surfactant-assisted glycerol organosolv pretreatment of sugarcane bagasse towards efficient enzymatic hydrolysis

Organosolv pretreatment effectively fractionates lignocellulosic biomass for efficient enzymatic hydrolysis, yielding fermentable sugars. However, substantial lignin redeposition on the substrate surface and residual lignin content exacerbate lignin’s inhibitory effects on subsequent enzymatic hydrolysis. Here, an in-situ lignin modification is proposed to address this challenge by incorporating polyethylene glycol (PEG) series into glycerol organosolv (GO) pretreatment. According to the results obtained, PEG-assisted GO pretreated substrate exhibited significantly increased sugar yield during enzymatic hydrolysis, particularly with PEG 4000, showing 35.4% higher glucose yield over 72 h. The improved glucose yield with PEG could be attributed to changes in the physicochemical structure and properties of residual lignin, mitigating its non-productive interaction with cellulase enzymes. PEG's presence in GO pretreatment also increased β-O-4 linkages preservation by 55% and reduced phenolic hydroxyl groups by 28% in lignin fragments versus no surfactants. This outcome resulted from introducing glycerol and PEG hydroxyl tails into the lignin structure, forming α-etherified lignin and rendering it more hydrophilic. Simulations confirmed strong Van Der Waals and hydrogen bonding interactions between lignin units and PEG, hindering lignin fragments repolymerization. Incorporating PEG in the organosolv pretreatment proves highly beneficial for cellulase-mediated lignocellulosic biorefinery, resembling a lignin-first strategy. The optimized process enables efficient biomass utilization for sustainable fuels and chemicals production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Specific molecular design of polycarboxylate polymers exhibiting optimal compatibility with clay contaminants in concrete

Highlights: • Allyl ether-based PCEs with short side chain length and low side chain density presented superior clay resistance. • PCEs with medium side chain density exhibited best clay robustness when compared at the absolute dosed quantities. • The proportion of PCE being intercalated into the layered structure of clay was quantified. It is widely recognized that the dispersing ability of polycarboxylate superplasticizers (PCEs) could be hindered due to the presence of clay contaminants in concrete. In this study, a series of allyl ether-based polycarboxylate superplasticizers possessing short polyethylene glycol side chains was successfully synthesized and probed for their clay tolerance. The resulting PCE polymers were characterized via Size Exclusion Chromatography (SEC) to obtain their molecular properties. Thereafter, their dispersing ability was probed in the absence and presence of sodium bentonite. Allyl ether-based polycarboxylate (APEG) polymers possessing short side chains were found to exhibit enhanced clay resistance as compared to that of conventional MPEG PCEs holding long pendant chains. The mode of interaction between APEG PCEs and bentonite was investigated via sorption and XRD measurements. The data revealed that APEG PCEs possessing a lower side chain density intercalate less into the interlayer space of bentonite than those exhibiting higher side chain density.

36 MATERIALS SCIENCE↗

Solid-state polymer magnesium supercapacitor

Here, the present article focuses on the development of a highly ion-conductive, solvent-free, solid-state polymer electrolyte membrane (PEM) via photopolymerization of polyethylene glycol diacrylate (PEGDA) network from its homogeneous melt mixtures containing succinonitrile (SCN) plasticizer and magnesium bis(trifluoromethane sulfonyl) imide Mg(TFSI) 2 salt. The above solid-state Mg-PEM exhibits a Helmholtz electric double-layer capacitor (EDLC) behavior in its supercapacitive symmetric carbonaceous electrode configuration. The electrochemical stability for this PEM membrane (20/40/40 PEGDA/SCN/Mg (TFSI) 2 ) was found to be approximately 3 V from linear sweep voltammetry with a specific capacitance of about 44 F/g from cyclic voltammetry and an energy density of approximately 17 Wh/kg in the 0–2 V range from the constant current density (CCD) experiment. Of particular interest is its excellent capacity retention of over 11,200 cycles, thus tested with the Coulombic efficiency of over 87%. Moreover, the energy density after extensive cycling for 11,200 has increased to approximately 56 Wh/kg at 10 mV/s in the potential range of 0–3 V relative to 17 Wh/kg in the potential range of 0–2 V at the same scan rate, attesting the excellent electrochemical stability and long life of the present Mg-PEM supercapacitor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Role of Intermolecular Interactions in Deep Eutectic Solvents for CO 2 Capture: Vibrational Spectroscopy and Quantum Chemical Studies

Recent research and reviews on CO 2 capture methods, along with advancements in industry, have highlighted high costs and energy-intensive nature as the primary limitations of conventional direct air capture and storage (DACS) methods. In response to these challenges, deep eutectic solvents (DESs) have emerged as promising absorbents due to their scalability, selectivity, and lower environmental impact compared to other absorbents. However, the molecular origins of their enhanced thermal stability and selectivity for DAC applications have not been explored before. Therefore, the current study focuses on a comprehensive investigation into the molecular interactions within an alkaline DES composed of potassium hydroxide (KOH) and ethylene glycol (EG). Combining Fourier transform infrared (FT-IR) and quantum chemical calculations, the study reports structural changes and intermolecular interactions induced in EG upon addition of KOH and its implications on CO 2 capture. Experimental and computational spectroscopic studies confirm the presence of noncovalent interactions (hydrogen bonds) within both EG and the KOH-EG system and point to the aggregation of ions at higher KOH concentrations. Additionally, molecular electrostatic potential (MESP) surface analysis, natural bond orbital (NBO) analysis, quantum theory of atoms-in-molecules (QTAIM) analysis, and reduced density gradient-noncovalent interaction (RDG-NCI) plot analysis elucidate changes in polarizability, charge distribution, hydrogen bond types, noncovalent interactions, and interaction strengths, respectively. Evaluation of explicit and hybrid models assesses their effectiveness in representing intermolecular interactions. This research enhances our understanding of molecular interactions in the KOH-EG system, which are essential for both the absorption and desorption of CO 2 . The study also aids in predicting and selecting DES components, optimizing their ratios with salts, and fine-tuning the properties of similar solvents and salts for enhanced CO 2 capture efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Aqueous Processed All-Polymer Solar Cells with High Open-Circuit Voltage Based on Low-Cost Thiophene–Quinoxaline Polymers

Eco-friendly solution processing and the low-cost synthesis of photoactive materials are important requirements for the commercialization of organic solar cells (OSCs). Although varieties of aqueous-soluble acceptors have been developed, the availability of aqueous-processable polymer donors remains quite limited. In particular, the generally shallow highest occupied molecular orbital (HOMO) energy levels of existing polymer donors limit further increases in the power conversion efficiency (PCE). Here, we design and synthesize two water/alcohol-processable polymer donors, poly[(thiophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-T)) and poly[(selenophene-2,5-diyl)-alt-(2-((13-(2,5,8,11-tetraoxadodecyl)-2,5,8,11-tetraoxatetradecan-14-yl)oxy)-6,7-difluoroquinoxaline-5,8-diyl)] (P(Qx8O-Se)) with oligo(ethylene glycol) (OEG) side chains, having deep HOMO energy levels (~–5.4 eV). The synthesis of the polymers is achieved in a few synthetic and purification steps at reduced cost. The theoretical calculations uncover that the dielectric environmental variations are responsible for the observed band gap lowering in OEG-based polymers compared to their alkylated counterparts. Notably, the aqueous-processed all-polymer solar cells (aq-APSCs) based on P(Qx8O-T) and poly[(N,N'-bis(3-(2-(2-(2-methoxyethoxy)-ethoxy)ethoxy)-2-((2-(2-(2-methoxyethoxy)ethoxy)ethoxy)-methyl)propyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl)-alt-(2,5-thiophene)] (P(NDIDEG-T)) active layer exhibit a PCE of 2.27% and high open-circuit voltage (V OC ) approaching 0.8 V, which are among the highest values for aq-APSCs reported to date. This study provides important clues for the design of low-cost, aqueous-processable polymer donors and the fabrication of aqueous-processable OSCs with high V OC .

14 SOLAR ENERGY↗

Techno-Economic and Life Cycle Assessments for Sustainable Rare Earth Recovery from Coal Byproducts using Biosorption

Coal byproducts could be a promising feedstock to alleviate the supply risk of critical rare earth elements (REEs) due to their abundance and REE content. Herein, we investigated the economic and environmental potential of producing REEs from coal fly ash and lignite through an integrated process of leaching, biosorption, and oxalic precipitation on the basis of experimental data and modeling results. Two microbe immobilization systems (polyethylene glycol diacrylate (PEGDA) microbe beads and Si sol–gels) were examined for their efficiency in immobilizing Arthrobacter nicotianae to selectively recover REEs. Techno-economic analysis revealed that North Dakota lignite could be a profitable feedstock when Si sol–gel is used due to its high cell loading and REE adsorption capacity as well as high reuse cycles. Life cycle analysis revealed that Si sol–gel-based biosorption could be more environmental friendly than the prevailing REE production in China due to the use of less toxic chemicals. However, fly ash sourced from Powder River Basin coals was neither profitable nor environmentally sustainable, primarily due to low solubility of high-value scandium at an economical pulp density (100 g ash/L of acid solution). To further improve the proposed biotechnology, future research could focus on scandium recovery, leaching efficiency at a high pulp density, and reuse cycles of the immobilized microbes.

01 COAL, LIGNITE, AND PEAT↗

Ionic liquids improve the long-term stability of perovskite solar cells

Achieving operational stability in halide perovskite solar cells remains a critical challenge for commercialization. Ionic liquids are promising bulk modifiers, yet their mechanistic role in perovskite crystallization is poorly understood. Here we engineered an ionic liquid, methoxyethoxymethyl-1-methylimidazole chloride (MEM-MIM-Cl), with an ethylene glycol ether side chain that regulates perovskite growth and stabilizes buried interfaces via synergistic interactions with NiO x . MEM-MIM-Cl induces a novel intermediate phase through chelation with undercoordinated Pb(II), suppressing defects and defect-induced degradation. Solar cells incorporating MEM-MIM-Cl achieved a power conversion efficiency of 25.9% and retained 90% of their initial performance after 1,500 h under continuous 1-sun illumination and 90 °C thermal stress—surpassing prior benchmarks under milder ageing conditions. Furthermore, diurnal cyclic ageing revealed unprecedented fatigue resistance, highlighting the dual role of MEM-MIM-Cl in simultaneously enhancing efficiency and operational resilience. In conclusion, this work elucidates design principles for functional ionic liquids while advancing perovskite photovoltaics towards industrial viability.

14 SOLAR ENERGY↗

ToF-SIMS evaluation of PEG-related mass peaks and applications in PEG detection in cosmetic products

Polyethylene glycols (PEGs) are used in industrial, medical, health care, and personal care applications. The cycling and disposal of synthetic polymers like PEGs pose significant environmental concerns. Detecting and monitoring PEGs in the real world calls for immediate attention. This study unveils the efficacy of time-of-flight secondary ion mass spectrometry (ToF-SIMS) as a reliable approach for precise analysis and identification of reference PEGs and PEGs used in cosmetic products. By comparing SIMS spectra, we show remarkable sensitivity in pinpointing distinctive ion peaks inherent to various PEG compounds. Moreover, the employment of principal component analysis effectively discriminates compositions among different samples. Notably, the application of SIMS two-dimensional image analysis visually portrays the spatial distribution of various PEGs as reference materials. The same is observed in authentic cosmetic products. The application of ToF-SIMS underscores its potential in distinguishing PEGs within intricate environmental context. ToF-SIMS provides an effective solution to studying emerging environmental challenges, offering straightforward sample preparation and superior detection of synthetic organics in mass spectral analysis. These features show that SIMS can serve as a promising alternative for evaluation and assessment of PEGs in terms of the source, emission, and transport of anthropogenic organics.

36 MATERIALS SCIENCE↗

Isothermal Versus Sensible Cold Storage: A Model-Based Performance Comparison for Pumped Thermal Electricity Storage

Pumped-thermal energy storage (PTES) systems consume and produce electrical energy using thermal storage media as an intermediate stage. PTES lends itself to long-duration energy storage to facilitate high penetration of intermittent electricity generation. This study presents a model-based comparison of two thermal storage types within a PTES system: a conventional, single-phase, stratified water-glycol sensible storage system (SGS), and an ideal isothermal, two-phase heat exchanger that freezes a water reservoir (isothermal heat exchanger (IHEX)). The SGS thermal storage capacity is based on the liquid’s sensible heat change with temperature, whereas the capacity of the IHEX is based on the latent heat of isothermally freezing and melting water. The idealized IHEX modeled here undergoes steady-state melting and freezing (in contrast to transient rates, as observed with ice-on-coil storage). A computational model of a complete PTES system is presented and used to evaluate the PTES system-level performance with each type of cold storage. Compared to SGS-based PTES, under nominal operating conditions, the IHEX-based PTES increased electrical round-trip efficiency from 61% to 82% and increased energy density from 1.13 to 8.09 kWh/m 3 In conclusion, the performance of the PTES configured with IHEX storage was also analyzed under varying operating parameters.

25 ENERGY STORAGE↗

Development of 225Ac-doped biocompatible nanoparticles for targeted alpha therapy

Abstract Targeted alpha therapy (TAT) relies on chemical affinity or active targeting using radioimmunoconjugates as strategies to deliver α-emitting radionuclides to cancerous tissue. These strategies can be affected by transmetalation of the parent radionuclide by competing ions in vivo and the bond-breaking recoil energy of decay daughters. The retention of α-emitting radionuclides and the dose delivered to cancer cells are influenced by these processes. Encapsulating α-emitting radionuclides within nanoparticles can help overcome many of these challenges. Poly(lactic- co -glycolic acid) (PLGA) nanoparticles are a biodegradable and biocompatible delivery platform that has been used for drug delivery. In this study, PLGA nanoparticles are utilized for encapsulation and retention of actinium-225 ([ 225 Ac]Ac 3+ ). Encapsulation of [ 225 Ac]Ac 3+ within PLGA nanoparticles (Z ave = 155.3 nm) was achieved by adapting a double-emulsion solvent evaporation method. The encapsulation efficiency was affected by both the solvent conditions and the chelation of [ 225 Ac]Ac 3+ . Chelation of [ 225 Ac]Ac 3+ to a lipophilic 2,9-bis-lactam-1,10-phenanthroline ligand ([ 225 Ac]AcBLPhen) significantly decreased its release (< 2%) and that of its decay daughters (< 50%) from PLGA nanoparticles. PLGA nanoparticles encapsulating [ 225 Ac]AcBLPhen significantly increased the delivery of [ 225 Ac]Ac 3+ to murine (E0771) and human (MCF-7 and MDA-MB-231) breast cancer cells with a concomitant increase in cell death over free [ 225 Ac]Ac 3+ in solution. These results demonstrate that PLGA nanoparticles have potential as radionuclide delivery platforms for TAT to advance precision radiotherapy for cancer. In addition, this technology offers an alternative use for ligands with poor aqueous solubility, low stability, or low affinity, allowing them to be repurposed for TAT by encapsulation within PLGA nanoparticles. Graphical Abstract

60 APPLIED LIFE SCIENCES↗

Solubility Testing to Support the Addition of Sodium Reactor Experiment Material to Sludge Batch 10

The Savannah River Site H-Canyon Facility is planning to discard dissolved Sodium Reactor Experiment (SRE) material into Tank 51 prior to Sludge Batch 10 (SB10). SB10 with the SRE material will be processed in the Defense Waste Processing Facility (DWPF) using the Nitric-Glycolic Acid (NGA) flowsheet. The DWPF Nuclear Criticality Safety Evaluation (NCSE) protects a 14:1 mass ratio of manganese to equivalent uranium-235 in both the solid and liquid phases during processing by requiring a 70:1 mass ratio in the feed. A concern was raised that freshly precipitated manganese in the SRE material will behave differently from the manganese in sludge during DWPF processing and potentially invalidate the criticality control. To mitigate risks to the DWPF criticality controls, the Savannah River National Laboratory (SRNL) performed a metals solubility test applicable to recently precipitated manganese and uranium, as would be expected with SRE transfers to SB10. The objective of this analysis is the tracking of partitioning of the primary fissile component (uranium-235) with the credited poison (manganese) between the aqueous and insoluble phases.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Thermal Management for a Novel Non-Heavy Rare-Earth Interior Permanent Magnet Machine

The work presents a thermal management solution for a novel non-heavy rare-earth permanent magnet machine being developed at Oak Ridge National Laboratory. The motor has been designed to minimize losses while maximizing performance for a range of speeds and power ratings. The novel motor design reduces rare-earth magnet usage, thereby avoiding supply chain issues. The motor component heat losses are established for operating windows and desired performance. These heat losses, along with windage losses, are being used to develop cooling solutions for different components of this machine. A novel thermal management solution for stators and rotors has been developed, and progress is presented in this paper. The stator cooling is achieved with the help of water-ethylene glycol flowing over the finned aluminum stator jacket, and rotor cooling with automatic transmission fluid passing through novel channels designed in the rotor laminations. The attempt is to establish effective cooling of the stator winding, laminations, and rotor magnets. A 3D conjugate heat transfer model has been developed for overall thermal analysis to establish a down- selected thermal management solution for the machine. The model, in addition to estimated component heat losses, includes windage losses and its impact on rotor and stator cooling. Overall, the work presents a workable thermal solution for the interior permanent magnet machine with potential for further improvements. Future work will involve establishing end winding and refinement of other end parts of the machine with the aim of establishing a robust thermal management solution. The work will also focus on different shapes (e.g., round, non-round, presence of wedges) of rotor-stator gaps and investigate windage losses and their impact on thermal management for higher rotational speeds for the machine.

30 DIRECT ENERGY CONVERSION↗

Transcriptome Analysis of Drought-Resistant and Drought-Sensitive Sorghum ( Sorghum bicolor ) Genotypes in Response to PEG-Induced Drought Stress

Drought is a major limiting factor of crop yields. In response to drought, plants reprogram their gene expression, which ultimately regulates a multitude of biochemical and physiological processes. The timing of this reprogramming and the nature of the drought-regulated genes in different genotypes are thought to confer differential tolerance to drought stress. Sorghum is a highly drought-tolerant crop and has been increasingly used as a model cereal to identify genes that confer tolerance. Also, there is considerable natural variation in resistance to drought in different sorghum genotypes. Here, we evaluated drought resistance in four genotypes to polyethylene glycol (PEG)-induced drought stress at the seedling stage and performed transcriptome analysis in seedlings of sorghum genotypes that are either drought-resistant or drought-sensitive to identify drought-regulated changes in gene expression that are unique to drought-resistant genotypes of sorghum. Our analysis revealed that about 180 genes are differentially regulated in response to drought stress only in drought-resistant genotypes and most of these (over 70%) are up-regulated in response to drought. Among these, about 70 genes are novel with no known function and the remaining are transcription factors, signaling and stress-related proteins implicated in drought tolerance in other crops. This study revealed a set of drought-regulated genes, including many genes encoding uncharacterized proteins that are associated with drought tolerance at the seedling stage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗